Fisher & Paykel BGCV21248, BGRV21236, BGRV23030HC, BGCV21230, BGCV21236 Installation manual
...
INSTALLATION INSTRUCTIONS
Backguard for
Professional Ranges
BGRV2 models
US CA
www.dcsappliances.com
591091A 04.16
1 SAFETY AND WARNINGS
!
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
●
Save these instructions for the local inspectors use.
●
To avoid hazard, follow these instructions carefully before installing or using this
product.
●
Please make this information available to the person installing the product - doing so
could reduce your installation costs.
●
If the installation requires alterations to the domestic electrical system, call a qualified
electrician. The electrician should also check that the socket cable section is suitable
for the electricity drawn by the range.
2 UNPACKING AND PARTS SUPPLIED
●
Service should only be done by authorized technicians. Technicians must disconnect the
power supply before servicing this appliance.
●
Installation must comply with your local building and electricity regulations.
●
Improper installation, adjustment alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating and maintenance instructions
thoroughly.
●
DO NOT obstruct the flow of combustion or ventilation air to the accompanying appliance.
Be sure a fresh air supply is available.
●
California Proposition 65 - The burning of gas cooking fuel generates some by-products which
are known by the State of California to cause cancer or reproductive harm. California law
requires businesses to warn customers of potential exposure to such substances. To minimize
exposure to these substances, always operate this unit according to the manufacturer’s
instructions and provide good ventilation to the room when cooking with gas.
●
Check local building codes for the proper method of installation. Local codes vary.
Installation, electrical connections, and grounding must comply with all applicable codes. In
the absence of local codes, the range should be installed in accordance with the latest edition
of National Fuel Gas Code ANSI Z223.1 and National Electrical Code ANSI / NFPA 70.
●
Do not place items of interest to children on racks or appliance. Children could be seriously
injured if they should climb onto or into the appliance to reach these items.
●
Do not place combustible material (paper, cloth, plastic, etc.) on the rack.
WALL MOUNT HIGH BACKGUARD
LOW SHELF Models
Low Shelf Rack & Handle Kit
30” & 36” Models (x2 Racks)
48” Models (x3 Racks)
Unpacking and handling
●
Inspect the backguard and racks to verify that there is no shipping
damage. If any damage is detected, call the shipper and initiate a
damage claim. DCS by Fisher & Paykel is not responsible for shipping
damage.
●
DO NOT discard any packing material (box, pallet, straps) until the
unit has been inspected.
●
Range Backguard
(model specific) (1)
WALL MOUNT HIGH BACKGUARD
HIGH SHELF Models
Remove the outer carton and any packing material and dispose
responsibly.
High Shelf Rack & Handle Kit
30” & 36” Models (x2 Racks)
48” Models (x3 Racks)
Angled Trim
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.dcsappliances.com or contact your local DCS by Fisher & Paykel dealer.
2
RANGE MOUNT LOW BACKGUARD
BGRV2-1230 BGRV2-1236 BGRV2-1248
WALL MOUNT HIGH BACKGUARD LOW SHELF
3 MODEL IDENTIFICATION
BGRV2-3030
WALL MOUNT HIGH BACKGUARD HIGH SHELF AND ANGLED VENT TRIM
BGRV2-3030H
BGRV2-3036
BGRV2-3036H
BGRV2-3048
BGRV2-3048H
3
4 INSTALLATION SCENARIOS AND USE OF BACKGUARDS
WALL INSTALLATION
Vent Trim
cooking
surface
0” Clearance
scenario 1
NO BACKGUARD USED
Integral Flat Vent Trim or
Angled Flat Vent Trim (
(supplied with range)
ISLAND INSTALLATION
RGCV2-305 models only)
Non-combustible
surface*
(required)
cooking
surface
scenario 2
NO BACKGUARD USED
Integral Flat Vent Trim or
Angled Flat Vent Trim (
(supplied with range)
Min. 6” (152mm)
Clearance
RGCV2-305 models only)
Combustible
Surface
Range Mount
Low Backguard
cooking
surface
10 3/8”
(263mm)
1/2”
(13mm)
0” Clearance
scenario 3 scenario 4
RANGE MOUNT LOW BACKGUARD
(purchased separately)
Wall Mount
cooking
surface
High Backguard
Low Shelf
(720mm)
28 3/8”
Non-combustible
surface*
(required)
0” Clearance
WALL MOUNT HIGH BACKGUARD LOW SHELF
(purchased separately)
1/2”
(13mm)
Non-combustible
surface*
(required)
Wall Mount
High Backguard
High Shelf
26 1/2”
(673mm)
cooking
surface
Angled Vent Trim
(required)
0” Clearance
scenario 5
WALL MOUNT HIGH BACKGUARD
HIGH SHELF AND ANGLED VENT TRIM KIT
(purchased separately)
1 5/16”
(33mm)
Non-combustible
surface*
or
Combustible
surface
Non-Combustible
Surface*
Vent Trim
cooking
surface
scenario 6 scenario 7
NO BACKGUARD USED
Integral Flat Vent Trim or Angled Flat Vent Trim (RGCV2-305 models only)
(supplied with range)
4
Combustible
Surface
Min. 6” (152mm)
Clearance
cooking
surface
NO BACKGUARD USED
Integral Flat Vent Trim or Angled Flat Vent Trim (RGCV2-305 models only)
(supplied with range)
4 INSTALLATION SCENARIOS AND USE OF BACKGUARDS
Important notes
●
All ranges come fitted standard with with either an Integral Flat Vent Trim or an Angled Vent Trim (RGCV2-305 models only)
●
There are three different backguards available for purchase:
●
Range Mount Low Backguard
●
Wall Mount High Backguard with Low Shelf
●
Wall Mount High Backguard with High Shelf, also supplied with an Angled Vent Trim.
●
For installations against non-combustible* surfaces only, you may install the range without a backguard or choose any of the three backguards.
●
For installations close to combustible surfaces (above the cooking surface), without a backguard, there must be a minimum 6” (152mm) clearance
(see Scenario 2 or 7 opposite)
●
For installations immediately against combustible surfaces (above the cooking surface), you must purchase and fit the Wall Mount High Backguard
High Shelf and Angled Vent Trim (see Scenario 5 opposite)
●
The cooking surface must sit flush or above the adjacent countertop level.
* Non-combustible surfaces:
as defined in ‘National Fuel Gas Code’ (ANSI Z223.1, Current Edition). Clearances from non-combustible materials
are not part of the ANSI Z21.1 scope and are not certified by UL. Clearances of less than 6” (152mm) must be
approved by the local codes and/or by the local authority having jurisdiction.
BACKGUARD MODEL NUMBERS
WALL
MOUNT HIGH
BACKGUARD
LOW SHELF
RANGE
RANGE
MOUNT LOW
BACKGUARD
30” models BGRV2-1230 BGRV2-3030 BGRV2-3030H 29 7/8” (759mm)
36” models BGRV2-1236 BGRV2-3036 BGRV2-3036H 35 7/8” (911mm)
48” models BGRV2-1248 BGRV2-3048 BGRV2-3048H 47 7/8” (1216mm)
WALL
MOUNT HIGH
BACKGUARD
HIGH SHELF
BACKGUARD
WIDTH
Note: For more information on Backguard installation, refer to the separate instructions provided with your backguard.
Backguard Installation Instructions can also be downloaded from our website, www.dcsappliances.com
5
5 PRODUCT DIMENSIONS
29 1/8”
(740mm)
5 7/8”
(150mm)
8 13/16”
(224mm)
WIDTH
1/2”
(13mm)
10 15/16”
(278mm)
26 1/2”
(673mm)
WIDTH
1 5/16”
(33mm)
5 3/8”
(136mm)
9 1/16”
(230mm)
10 3/8”
(263mm)
WIDTH
1/2”
(13mm)
RANGE MOUNT LOW BACKGUARD
FRONT
PROFILE
WALL MOUNT HIGH BACKGUARD HIGH SHELF
WALL MOUNT HIGH BACKGUARD LOW SHELF
FRONT
PROFILE
6
FRONT
PROFILE
SUITABLE
RANGE
30” models BGRV2-1230 BGRV2-3030 BGRV2-3030H 29 7/8” (759mm)
36” models BGRV2-1236 BGRV2-3036 BGRV2-3036H 35 7/8” (911mm)
48” models BGRV2-1248 BGRV2-3048 BGRV2-3048H 47 7/8” (1216mm)
RANGE
MOUNT LOW
BACKGUARD
WALL
MOUNT HIGH
BACKGUARD
LOW SHELF
WALL
MOUNT HIGH
BACKGUARD
HIGH SHELF
BACKGUARD
WIDTH
6-A RANGE MOUNT LOW BACKGUARD - ASSEMBLY
1
Attach low backguard to the rear of the range
1 Align the backguard with the range, so that it
rests on the vent trim.
2 Fasten the bottom of the backguard to the rear
of the range using all the screws provided, as
shown.
The two center screws come already attached to
the range for your convenience.
Finally position range
3 Push the range into position.
Follow the rest of the instructions shown in the
range installation instructions.
2
Center screw
These screws
come pre-attached to
rear of range
3
7
6-B WALL MOUNT HIGH BACKGUARD WITH LOW SHELF - ASSEMBLY
1
VENT HOOD
BACKGUARD
RANGE
2
End
cap
3
Center
stanchion
#10 machine
Rod
screws
End
cap
1 Recommended installation order:
1] VENT HOOD
2] BACKGUARD
3] RANGE
Locate and Mark the two mounting screw locations
2 Use the diagram below depending on your
particular model.
Attach rod etc
3 Attach rod, end caps and center stanchion to
backguard with #10 machine screws supplied.
continued over...
B
C
Top of Vent Trim
Mounting screw locations
A
B
C
30” MODELS 36” MODELS 48” MODELS
inches (mm) inches (mm) inches (mm)
6 15/16” (176) 1 15/16” (50) 7 15/16” (202)
16” (406) 32” (813) 32” (813)
26 9/16” (675) 26 9/16” (675) 26 9/16” (675)
Mounting
Hole
location
Mounting
Hole
location
A
8
Loading...