Fisher & Paykel CDV3365HN, CDV3304HN, CDV3304L, CDV3365HL, CDV3304HL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL
...
GAS COOKTOPS
PROFESSIONAL
CDV-65H, CDV-65 CDV-04H, CDV-04
INSTALLATION GUIDE
US CA
!
WARNING!
If the information in this manual is not
followed exactly, a fire or explosion
may result causing property damage,
personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any otherappliance.
SAFETY AND WARNINGS
!
WARNING!
NEVER use this appliance as a
space heater to heat or warm the
room. Doing so may result in carbon
monoxide poisoning and overheating
of theappliance.
What to Do if you Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your
building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas
supplier, call the fire department.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Never operate the top surface cooking
section of this appliance unattended.
• Failure to follow this warning statement
could result in fire, explosion or burn
hazard that could cause property damage,
personal injury or death.
• If a fire should occur, keep away from the
appliance and immediately call your fire
department.
an oil/grease fire with water
Do not attempt to extinguish
2
SAFETY AND WARNINGS
!
WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• Before carrying out any work on the electrical
section of the appliance, it must be disconnected
from the mains electricitysupply.
• Connection to a good ground wiring system is
absolutely essential and mandatory.
• Alterations to the domestic wiring system must
only be made by a qualified electrician.
!
WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
READ AND SAVE THIS GUIDE
WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety instructions listed below. Read all the guidance before using the appliance.
Servicing
z
Do not repair or replace any part of the appliance unless specifically recommended in
the user guide. All other servicing should be undertaken be a Fisher & Paykel trained and
supported service technician or qualified person.
z
Technicians must disconnect the power supply before servicing this appliance.
z
Please make this information available to the person installing the appliance
z
This appliance must be installed and connected to the mains power supply only by a
suitably qualified person according to these installation instructions and in compliance
with any applicable local building and electricity regulations. Failuretoinstall the
appliance correctly could invalidate any warranty or liability claims.
Gas Requirements
z
Be sure that the unit being installed is set up for the kind of gas being used. The
gasrangetop is shipped from the factory set and adjusted for Natural Gas or LP (propane),
depending on the specific model ordered. Verify that the rangetop is compatible with the
gas at the installation site before proceeding further.
z
Return cooktop to dealer if the unit is not set for site gas supply.
General
z
The appliance must not be installed behind a decorative door in order to avoid
overheating.
z
The cooktop must be grounded.
z
Installation must comply with your local building and electricity regulations.
z
Ensure the installer shows the customer where the gas supply shut-off valve is located.
z
A circuit breaker is recommended.
z
If the power supply cable is damaged, it must be replaced by the manufacturer, itsservice
agent or similarly qualified person in order to avoid a hazard.
z
Do not use adaptors, reducers or branching devices to connect the oven to
themainselectricity supply, as they can cause overheating and burning.
z
Improper installation, adjustment alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating and maintenance instructions
thoroughly before using, installing or servicing this appliance.
z
DO NOT obstruct the flow of combustion or ventilation air to the appliance.
Besureafresh air supply is available.
z
Check local building codes for the proper method of cooktop installation. Local codes
vary. Installation, electrical connections, and grounding must comply with all applicable
codes. In the absence of local codes, the cooktop should be installed in accordance with
the latest edition of National Fuel Gas Code ANSI Z223.1 and National Electrical Code
ANSI / NFPA 70.
z
The cooktops are tested in accordance with ANSI Z21.1 Standard for Household Cooking
Gas Appliances. These cooktops must be installed in conjunction with a suitable overhead
vent hood. (See ventilation requirements). Due to the high heat capacity of this unit,
particular attention should be paid to the hood and duct work installation to ensure it
meets local building codes. To eliminate risk of burns or fire by reaching over heated
surface units, cabinet storage located above the surface units should be avoided.
z
In Canada: Installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes. Installation must be in accordance with
the current CAN/CGA B149.1 & 2 Gas Installation codes and/or local codes. Electrical
installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
3
COMPONENTS REQUIRED
PARTS TOOLS
z
Keep all packing materials until the unit has been inspected.
z
Inspect the product to ensure there is no shipping damage. If any damage is detected
contact the dealer or retailer you bought the product from to report the damage.
z
Fisher & Paykel is not responsible for shipping damage.
Supplied
Not supplied
Regulator (1) Brackets (4) Screws (4)
Powered driver Flat-head screw driver
15/16" spanner (2)
4
B
PRODUCT DIMENSIONS 30" MODELS
C
PLAN
H
ISOMETRIC
G
PRODUCT DIMENSIONS
30" MODELS
IN MM
A Overall height* 4 5/16 110
B Overall width 30 762
C Overall depth 21 533
D Height of chassis 4 102
E Width of chassis 28 7/16 723
F Depth of chassis 19 3/8 492
G Height above countertop 3/8 10
H Height above countertop to top of grates 1 9/16 40
I Distance from right edge of chassis to centre
of gas inlet
J Distance from rear edge of chassis to centre of
gas inlet
K Distance from right edge of chassis to centre
of power cord
L Distance from rear edge of chassis to centre of
power cord
*excluding grates
2 3/4 70
1 5/16 33
7/ 8 22
13/16 21
A
k
i
fe
FRONT PROFILE
j
l
D
PRODUCT WEIGHT
30" MODELS
LB KG
Weight of product (excluding packaging) 64 29
CDV3 304 model illustrated
Dimensions may vary by ± 2 mm
5
B
PRODUCT DIMENSIONS 36" MODELS
A
C
PLAN
e
i
k
H
ISOMETRIC
f
j
l
G
D
PRODUCT DIMENSIONS
36" MODELS
IN MM
A Overall height* 4 5/16 110
B Overall width 36 915
C Overall depth 21 533
D Height of chassis 4 102
E Width of chassis 34 7/16 874
F Depth of chassis 19 3/8 492
G Height above countertop 3/8 10
H Height above countertop to top of grates 1 9/16 40
I Distance from right edge of chassis to centre of
gas inlet
J Distance from rear edge of chassis to centre of
gas inlet
K Distance from right edge of chassis to centre of
power cord
L Distance from rear edge of chassis to centre of
power cord
*excluding grates
2 3/4 70
1 5/16 33
7/ 8 22
13/16 21
36" MODELS
PRODUCT WEIGHT
LB KG
Weight of product (excluding packaging) 90 41
FRONT PROFILE
CDV3 365 model illustrated
6
Dimensions may vary by ± 2 mm
CABINETRY DIMENSIONS
30" CUTOUT
D D
E
B
A
C
F
36" CUTOUT
E
B
C
A
F
CABINETRY DIMENSIONS
A Min. height allowance 4 102
B Depth 19 3/4 502
C Width 28 5/8 727
D Max. depth of overhead cabinetry 13 330
E Min. width of ventilation hood required 30 762
F Min. distance from rear edge of cutout to nearest
combustible surface
30" MODELS
IN MM
2 51
CABINETRY DIMENSIONS
A Min. height allowance 4 102
B Depth 19 3/4 502
C Width 34 3/4 883
D Max. depth of overhead cabinetry 13 330
E Min. width of ventilation hood required 36 914
F Min. distance from rear edge of cutout to nearest
combustible surface
36" MODELS
IN MM
2 51
7
CABINETRY DIMENSIONS
CLEARANCES
The below clearances apply to both wall and island installations for all models.
Ensure the cook surface sits flush or above the adjacent countertop and any openings behind or under the cooktop are sealed. Flow of combustion and ventilation air must not be obstructed.
CLEARANCE DIMENSIONS
ALL MODELS
IN MM
B
C
A A
C
A Min. distance from side of cooktop to nearest:
z
vertical combustible surface 12 305
B Min. distance from cook surface to overhead:
z
combustible surface 36 914
z
non-combustible surface 30 762
C Min. distance between countertop and cabinet 18 457
Non-combustible surfaces: as defined in ‘National Fuel Gas Code’ (ANSI Z223.1, Current Edition). Clearances from noncombustible materials are not part of the ANSI Z21.1 scope and are not certified by UL. Clearances of less than 6" (152mm) must
be approved by the local codes and/or by the local authority having jurisdiction.
8
VENTILATION REQUIREMENTS
z
Ventilation hoods and blowers are designed for use with single wall ducting, however some local building codes or inspectors may require double wall ducting and/or a damper. Consultlocal
building codes and/or agencies, before installing to ensure local requirements are met. Semi-rigid ducting is recommended for maximum effectiveness.
z
Hood blower speeds should be variable to reduce noise and loss of household air.
z
Due to a high volume of ventilation air, a source of make-up air (outside replacement air) is recommended. This is particularly important for tightly sealed and insulated homes. A reputable
heating and ventilating contractor should be consulted.
WALL INSTALLATION
ISLAND INSTALLATION
Non-combustible Non-combustibleCombustible Combustible
C C
C C
A A
B B
VENTILATION UNIT WALL INSTALLATION RECOMMENDATIONS
A min. 30" (762mm) max. 42 (762mm)
Hood
B min. 36" (914mm) max. 42 (762mm)
C min. 19" (480mm)
30" Cooktop min. 550 CFM
Blower
36" Cooktop min. 550 CFM
VENTILATION UNIT ISLAND INSTALLATION RECOMMENDATIONS
A min. 30" (762mm) max. 42 (762mm)
Hood
B min. 36" (914mm) max. 42 (762mm)
C min. 19" (480mm)
30" Cooktop min. 550 CFM
Blower
36" Cooktop min. 550 CFM
9
1
INSTALLATION ELECTRICAL REQUIREMENTS
The electrical supply must be a correctly polarized, grounded 120 V AC, 60 Hz, single phase
circuit suitable for the maximum current draw of the model, as detailed in the table below.
Please verify your model’s current draw by checking the rating label on the cooktop.
Required grounding method
Gently lower the cooktop into the cutout
ensuring you have access below the
countertop to fit and secure the brackets.
This appliance is factory equipped with a power supply cord with a three-prong grounding
plug (with polarized parallel blades). It must be plugged into a mating grounding type
receptacle, connected to a correctly polarized 120 Volt circuit. If the circuit does not have a
grounding type receptacle, it is the responsibility and obligation of the installer to have the
existing receptacle changed to a properly grounded and polarized receptacle in accordance
with all applicable local codes and ordinances by a qualified electrician. In the absence of local
codes and ordinances, the receptacle replacement shall be in accordance with the National
Electrical Code.
The third prong should not, under ANY circumstances, be cut or removed.
MODEL VOLTAGE MAX. CURRENT FREQUENCY
2
3
Fix the four supplied brackets to the
base of the cooktop.
Tighten all screws to secure the
cooktop to the countertop.
Ensure cooktop is level.
CDV3 36" models 120 V 0.10 A 60 Hz
CDV3 30" models 120 V 0.10 A 60 Hz
z
This cooktop must be grounded.
z
Always disconnect electric supply cord from the wall outlet or service disconnect before
servicing this appliance.
z
Observe all governing codes and ordinances when grounding, in absence of which, observe
National Electrical Code ANSI / NFPA No. 70.
The rating label
is located on
the base of the
cooktop towards
the front right.
A wiring
diagram label
is attached to
the bottom of
thecooktop.
10
GAS CONNECTION
Verify the type of gas supplied to the location. The cooktop is shipped from the factory set up and adjusted for Natural Gas or LP, depending on the specific model ordered. If the cooktop is not set
for the gas supplied at the site, return to the dealer.
Pressure testing at test pressures in excess of 1/2 psig (3.5 kPa.): the cooktop and its individual shut-off valve must be disconnected from the gas supply piping system
Pressure testing at test pressures equal to or less than 1/2 psig (3.5 kPa.): The cooktop must be isolated from the building’s gas supply piping system by closing its individual manual shut-off valve
LP GAS CONNECTION NATURAL GAS CONNECTION
Connection: 1/2" NPT Minimum 5/8" dia. flex line. Supply pressure: 6" to 9" W.CConnection: 1/2" NPT Minimum 5/8" dia. flex line. Supply Pressure: 11" to 14" W.C.
A regulator is required at the LP source to provide a maximum pressure of 14" W.C. to the
cooktop regulator.
A manual shut-off valve (not supplied) must be installed in an accessible location in the
gas line external to the appliance for the purpose of turning on or shutting off gas to the
appliance. In Massachusetts, such shut-off valves should be approved by the Board of State
Examiners of Plumbers & Gas Fitters. The shut-off valve must be located within 6 feet (1.8
meters) of the appliance.
Ensure the gas supply is turned off at the wall valve before connecting the appliance. The
gas supply connections should be made by a qualified technician and in accordance with
local codes or ordinances. In the absence of a local code, the installation must conform to
the latest edition of National Fuel Gas Code ANSI Z223.1. When within the Commonwealth of
Massachusetts, this appliance must be installed by a licensed plumber or gas fitter.
To prepare the unit for connection to the gas supply
Thread the supplied 1/2" pipe nipple into the elbow on the end of the manifold. The elbow is
located inside the chassis of the unit, on the end of the manifold, facing down. It is accessible
through the square cutout in the left rear corner of the chassis bottom. Connect the outlet of
the regulator to the exposed end of the nipple, connect the flex line from the gas supply to the
inlet side of the regulator.
Fisher & Paykel recommends installing the manual shutoff valve in a location readily accessible
by the customer, so that gas to the appliance can be shut off in an emergency situation.
However, the appliance must not be modified in any way to accommodate such placement.
Pipe sealant must be used on all pipe threads.
The gas supply line must not protrude beyond the back of the appliance.
Ensure the gas supply is turned off at the wall valve before connecting the appliance. Leaktesting of the appliance shall be conducted according to the manufacturer’s instructions. See
instructions following. When checking the manifold gas pressure, the inlet pressure to the
regulator should be at least 7.0" W.C. for natural gas or 12.0" for LP.
The flex line for the gas supply must be metal and be approved for appliance use by a
certifying agency (CSA, CGA, or UL). Never use a hose made of rubber or other synthetic
material, as the heat may cause the hose to melt and develop leaks.
The arrow on the regulator indicating direction of gas flow should be pointing towards the
unit.
base of product
1/2" coupling
1/2" close nipple
Regulator
1/2" x 5" close nipple
1/2" NPT to 3/8"
flare adapter
to gas supply
11
COOKTOP BURNERS LEAK TESTING
lifting off stable blue flameyellow tip
z
To check that the ignition system operates correctly, light each burner by itself, then all
burners in combination.
z
Check for a well-defined blue flame without any yellow tipping.
z
If any abnormality is evident, check that the components of the burner assembly are
located properly.
●
No air shutter adjustment is possible on the cooktop. Correct operation is achieved with
factory installed settings for the correct gas type.
z
When installing the burner port ring, align the two locating pins in the bottom side of the
port ring with the locating notch and center holes on the top side of the simmer ring, and
make sure these are properly engaged.
z
Incorrect installation may produce a potentially dangerous flame and result in poor
burner performance.
z
If proper operation cannot be obtained, contact Customer Care or your nearest
Fisher&Paykel Authorized Service Center.
z
The rangetop must not be used until proper operation has been achieved.
GAS
ON
z
Ensure all dials are set to OFF before connecting cooktop to gas supply.
z
After final gas connection is made, turn gas supply on and test all connections in gas supply
piping for gas leaks with a soapy water solution.
z
In order to avoid property damage or serious personal injury, never use a match or open
flame. If a leak is present, tighten joint or unscrew, apply more joint compound, tighten
again and retest connection for leak.
12
TO BE COMPLETED BY THE INSTALLER
GENERAL
Specified clearance maintained.
Unit is level–front to back and side to side.
All packaging materials have been removed.
Dials turn correctly and freely.
Burners light satisfactorily, both individually and with other burners operating.
Flame adjustments made if required.
FINAL CHECKLIST
GAS
ELECTRICAL
Connection: 1/2 NPT with a minimum 5/8" diameter flex line. Site gas supply is
compatible with cooktop model, and sufficient pressure is available
The pressure regulator which is connected to the manifold is set correctly
Manual gas shut-off valve installed in an accessible location.
Unit tested and free of gas leaks.
Receptacle with correctly rated over-current protection is provided for service
cordconnection.
Adequate ground connection.
Complete and keep for safe reference:
Model
Serial no.
Purchase date
Purchaser
Dealer address
Installer’s name
Installer’s signature
Installation company
Installation date
13
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2020. All rights reserved.
The models shown in this guide may not be available in all markets
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher&Paykel dealer.
and are subject to change at any time.
592192A 05.20
Loading...