Fisher LO540 User Manual

L0540
Newborn Baby
Older Baby
Toddler
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.com/uk
Consumer Information
WARNING
To prevent serious injury or death:
Fall Hazard - It is dangerous to use this
product on an elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor.
Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the product can tip over and cause suffoca­tion in soft surfaces.
• Never leave child unattended.
• Never use as a carrier or lift while child is seated. Never use the toy bar as a handle.
• Use the upright position only when child has developed enough upper body control to sit without leaning forward.
• Always use the restraint system until child is able to climb in and out of the product unassisted.
• Reclined position not recommended for children who cannot sit up by them­selves (6 months approximately, until 9 Kg/20 lbs).
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Toy (Toy may
be different)
Pad with Seat Back Tube Hint: Please refer to the care
section to remove the seat back tube for cleaning.
CAUTION
This package contains small parts in its unassembled state. Adult assembly is required.
• Please read these instructions before assembly and use of this product.
• Adult assembly is required. Tool needed for assembly: Phillips screw­driver (not included).
• Requires one “D” (LR20) alkaline battery (not included) for soother operation. Toy includes one non-replaceable button cell battery.
• Product features and decorations may vary from photographs.
Assembly
IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
Crossbar
3
• Insert and "snap" the back rails into the sockets in the side rails. Pull up on the back rails to be sure they are secure.
Side Rails
1
• Place the side rails on a flat surface.
• Fit the crossbar tabs into the small rectangular opening in each side rail. Push the crossbar down completely.
• Insert two #4 x 20 mm screws into the crossbar and tighten.
PUSH
PUSH
LIFT
LIFT
2
4
• First lift the front rails and then push out the back rails.
Seat Back Tube
Socket
Assembly
Pad
Socket
5
• Insert the ends of the seat back tube (inside the pad) into the sockets in the front rail. Push down on the seat back tube until you hear a “click” on each side.
• Pull up on the seat back tube to be sure it is secure.
6
• Locate the pocket in the bottom of the pad.
• Fit the hardboard (attached to the front bar) into the pocket in the pad.
Toy Bar
9
Assembly
Clamp
• Fit the toy bar clamp to the top of the front rail. Push the toy bar clamp down to “snap” it into place.
Hint: To remove the toy bar, lift the edge of the clamp and pull to remove.
• Fit the toy into the slot in the top of the front rail.
Battery Installation
Hint: We recommend using an alkaline battery for longer battery life.
• Turn the product face down.
• Loosen the screw in the battery compartment door and remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
IMPORTANT! If vibrations become faint, or if there are no vibrations, remove the “D” (LR20) battery from the soothing unit and dispose of it properly. Replace the battery with a new “D” (LR20) alkaline battery.
• Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).
+
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
"D" (LR20)
1,5V x 1
-
Newborn-to-Toddler Portable Rocker
Newborn Baby
Toddler
Older Baby
7
WARNING
To prevent serious injury or death:
• Use the upright position only when child has developed enough upper body control to sit without leaning forward.
• Reclined position not recommended for children who cannot sit up by themselves (6 months approximately, until 9 Kg/20 lbs).
Setup
91011
Soothing Vibrations and Fun Music Fold for Portability and Storage
PRESS
1
• Make sure your child is properly secured in the seat.
• Slide the power switch on the soothing unit to for vibrations and to turn vibrations off.
O
Note: If vibrations from the soothing unit become faint, or if there are no vibrations, remove the battery from the soothing unit and dispose of it properly. Replace the battery with a new “D” (LR20) alkaline battery.
• Pull the ring on the toy for a delightful tune!
• Press both frame release buttons.
2
• Lift the back rails from the side rails.
LIFT
3
• Push the back rails toward the front rails.
• The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Do not immerse the frame or the toys.
To remove the pad:
• Unfasten the pad flaps.
• Remove the pad clips from the front bar.
• Remove the hardboard from the pocket in the pad.
4
• Lower the seat back.
• Press the seat back tube release buttons on each side of the front rails. Pull to remove the seat back tube. Remove the seat back tube from the sleeve in the pad.
To replace the pad,
in the top of the pad. Then, follow the assembly instructions.
first insert the seat back tube into the sleeve
Loading...