Page 1
We Ma ke Th in gs Eas y
Installation Guides
H2i
sup p o r t@ f i ng e r t ec . c om
H2i
Door Access & Time Attendance System
Step 1
Determine the Location and Positioning
of the Installation
• Avoid installing the terminals in locations with high moisture or
condensation levels in the air
• The recommended installation height of the terminal from the
ground is 1.2 meter.
Step 2
Mounting of Terminals on A Wall
Back Plate
i
H2
support
rtec.com
@finge
4 feet / 1.2 meter
(recommended)
•
After determining the height of the terminal from the ground
level and have made the relevant marks on the wall, drill the
screws into the wall to hang the back plate.
Refer to Appendix II for dimensions and measurements of instal
lation.
Step 3
Wiring for Power Supply
The power input ports for these models are located at the rear of
the terminals. There is no adapter plug supplied with the models,
instead you need to source for power cable (red and black cables)
to connect the power from the terminal to the AdapTec.
CONNECTION PORT
1. Single Connection
2. Network Connection
CONNECTIONPORT
-
For
NC or
NO
door
lock
system
RS485
485A
485B
RX+
RX-
RS485 Data Converter
485A
485B
485A
485B
RX+
RX-
RS485 Data Converter
ACCESS
GND
BUT
SEN
NO
COM
NC
POWER SUPPLYPORT
DC12V
Power Supply
Back of Terminal
+12V
GND
TCP/IP PORT
(Ethernet Connection)
TCP/IP
WIEGAND
INPUT
CONNECTION
PORT
+12V
IWD1
IWD0
RLED
GLED
BEEP
GND
3rd party
controller
with 26 bits
wiegand
output
WIEGAND
OUTPUT
CONNECTION
PORT
WD0
WD1
3rd party
controller
with 26 bits
wiegand
output
-
w w w . f i n g e r t e c . c o m
Page 2
Step 4
Setting Up Data Communications
(Skip this step if you are using USB ash disk to transfer data)
The data communication ports are positioned at the rear of the
terminals, please refer to the diagrams shown on Step 3 to determine the wiring. Plug the communication jacks (TCP/IP or RS485)
to the corresponding ports.
TCP/IP – LAN Connection
For TCP/IP connection, plug the RJ45 jack into the TCP/IP (LAN)
Port of the terminal. Connect the other end (normal RJ45 jack) to
the local area network hub or a PC. Configure the device ID, IP address, subnet mask and Gateway by using TCMS V2 software (refer
to the hardware user manual for details).
RS485 – Serial Port Connection
Plug the communication jack that is provided in the package to
connect to the communication port of the terminal. Select wires
with label RS485+, RS485- and GND, and connect the other end
of these wires to an RS232/485 data converter. Connect the other
end of the data converter to a DB9 female connector. Configure
the device ID and baudrate of the terminal (refer to the hardware
user manual for details).
Step 5
Finalizing the installation
1. Check that all cable connections are done correctly.
2. Attach the terminal to the corresponding back plates, tighten
the screws to secure the terminal on the wall
3. Switch on the power to the terminal.
4. Start using the terminal.
Other Accessories
Note: All Accessories are offered at http://accessory.fingertec.com
AdapTec
R
O
L
O
O
C
K
D
T
I
M
E
R
We Ma ke Th in gs Eas y
AdapTec AC
The AdapTec AC is a 12VDC power supply inclusive of a 110~240VAC
switching linear power. The AdapTec supplies 12VDC power to the
FingerTec terminal and door lock system as well as charges a 12VDC
7.0Ah backup battery simultaneously. During an event of a power fail-
ure, the back up battery automatically provides power to the terminal
and maintains the door lock system. The AdapTec AC also prevents a
secured door from being opened if it has been tampered with.
Enclosures
FingerTec offers enclosures to protect the terminals from being meddled with by unauthorized persons.
Door Lock Accessories
FingerTec offers various door locks accessories to complement FingerTec door access product range.
Page 3
Appendix I
Power Supply & Door Lock System Wiring Diagrams
Appendix II
Terminal Dimensions and Measurements
Diagram1 • Normally Close (NC)
DC12V 3A
Power Supply
EM Lock (NC)
Emergency Break 2
Glass (Type NC)
Overwrite Switch A
(Type NC)
--+
3
C
Release button
Door sensor
+12V
GND
485-
485+
GND
BUT
SEN
NO
COM
NC
AL-
AL+
Diagram 2 • Normally Open (NO)
DC12V 3A
Power Supply
EM Lock (NO)
Emergency Break 1
Glass (Type NO)
Overwrite Switch B
(Type NO)
_
+
3
D
Release button
Door sensor
+12V
GND
485-
485+
GND
BUT
SEN
NO
COM
NC
AL-
AL+
Door Lock Connectors
WIRING PORT USAGE
Dry Contact
NO
NC
COM
SEN
GND
BUT
AL+
AL-
(Independent power supply for door lock)
• NO type door lock (NO-COM)
• NC type door lock (NC-COM)
Power Contact
(Using power from terminal to power on door lock)
• NO type door lock (NO-GND)
• NC type door lock (NC-GND)
Dry Contact
(Independent power supply for door lock)
• NO type door lock (NO-COM)
• NC type door lock (NC-COM)
Power contact
(Using power from terminal to power on door lock)
• COM1 - +12V
Door Sensor (SEN-GND)
Release Button(BUT-GND)
Alarm System
NO or NC Type – Check in Advance Options
The terminal will trigger the alarm output (NO or NC) for the
following situations:
• Door forced open (A door sensor must first be installed)
• Door open time out (A door sensor must first be installed)
• Terminal has been illegally dismantled
28 mm
18 mm
o
3 mm
22 mm
35 mm
138 mm
152 mm
47 mm
Diagram 3 • Other Accessories
DC12V 3A
Power Supply
Door Sensor
Alarm device Type NO
or NC Dry contact
+12V
GND
485-
485+
GND
BUT
SEN
NO
COM
NC
AL-
AL+
7 mm
8 mm
10 mm
o
3 mm
70 mm
78 mm
Front View of H2i
8 mm
10 mm
Loading...