FingerTec Face ID 4 Installation Guide
Face ID4 d
Installation Guide
Step 1
Determine the Location and Positioning
of the Installation
•
Avoid installing the terminals in locations that has contact with
a strong light source (e.g direct sunlight, spotlight, fluorescent
light, etc)
• Avoid installing the terminals in locations with high moisture or
condensation levels in the air.
• The recommended installation height of the terminal from the
ground is 1.2 meters.
Step 2
Mounting of Terminals on a Wall
Back Plate
INSTALLATION TIPS:
A good installation location of Face ID 4 must
1 - Avoid sunlight.
2 - Be 2 meters away from any light source e.g.
ceiling direct flourescent light
3 - Suggested 1.2m from the ground level (measure from ground to the camera)
Step 3
Wiring for Power Supply
Connection points for power and communication are available at
the back of the terminal. Refer to the following diagrams for the
correct installation.
POWER SUPPLY (A)
DC12V 3A
Power Supply
GND
+12V
Face ID 4
Series
Face Recognition System for
Time Attendance and Access Control*
www.fingertec.com
support@fingertec.com
4 feet / 1.2 meter
(recommended)
• After determining the height of the terminal from the ground
level and have made the relevant marks on the wall, drill the
screws into the wall to fix the back plate.
Refer to Appendix II for dimensions and measurements of instal-
lation.
TCP/IP Port
TCP/IP
DC12V 3A
Power Supply
Only available
for Face ID 4d
Door Lock
System
Alarm Output
Step 4
Setting Up Data Communication
(Skip this step if you are using USB ash disk to transfer data)
The data communication ports are positioned at the rear of the
terminals, please refer to the diagrams shown on Step 3 to determine the wiring. Plug the jacks (RJ45) to the ports.
TCP/IP – LAN Connection
For TCP/IP connection, plug the RJ45 jack into the TCP/IP (LAN)
port of the terminal. Connect the other end (normal RJ45 jack) to
the local area network hub or a PC. Configure the device ID, IP address, subnet mask and Gateway in the terminal (refer to the hardware user manual for details).
Other Accessories
Note: All accessories are offered at http://accessory.fingertec.com
AdapTec Plus
Appendix I
Power Supply & Door Lock System
Wiring Diagrams
Diagram1 • Normally Close (NC)
Step 5
Finalizing the Installation
1. Check that all cable connections are done correctly.
2. Attach the terminal to the corresponding back plates,
tighten the screws to secure the terminal on the wall
3. Switch on the power to the terminal.
4. Start using the terminal.
The AdapTec Plus is a 12VDC power supply inclusive of a
110~240VAC switching linear power. The AdapTec Plus supplies
12VDC power to the FingerTec terminal and door lock system as
well as charges a 12VDC 7.0Ah backup battery simultaneously.
During an event of a power failure, the back up battery automatically provides power to the terminal and maintains the door lock
system. The AdapTec Plus also prevents a secured door from being
opened if it has been tampered with.
Door Lock Accessories
FingerTec offers various door locks accessories to complement
FingerTec door access product range. Go to
gertec.com
to view the complete list.
http://accessory.fin-
Door
Sensor
DC12V 3A
GND 12V NC1 COM1 NO1
SEN GND BUT NO2 COM2 NC2
Release
Button
Alarm Device
+
(NC)
Alarm Device
Diagram 2 • Normally Open (NO)
Door
Sensor
DC12V 3A
GND 12V NC1 COM1 NO1
SEN GND BUT NO2 COM2 NC2
Release
Button
Alarm Device
+
(NC)
Alarm Device
(NO)
(NO)
+
2
3
A
C
+
Emergency
2
Break Glass
3
A
Key Switch
C
EM Lock
(NC)
Emergency
Break Glass
(NC)
Override
Key Switch
(NC)
EM Lock
(NO)
(NO)
Override
(NO)
Loading...