E36GC75PSS0
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.
If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
FOR YOUR SAFETY:
-- Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
-- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
-- Installation and service must be performed by a qualified installer,
service agency orthe gas supplier.
For Standard
installation:
Gas Cooktop Dimensions
30"(76.2cm)
Min.*
* 30" (76,2 cm) min. for
unprotected cabinet and
24" (61cm) min. for cabinet
with protected bottom surface.
Gas Cooktop Cutout
Dimensions
2"(5,1 cm) Dia.
Opening to route power
cable. Seal opening
routing power cable.
3" (7,6 cm)
C
4" X 4" (10,2 cm x 10,2 ......
cm) opening to route gas
supply. Seal opening after
routing gas line
G
H
i
Figure 1
F
**Note: D & Eare critical to the proper
installation of the cooktop. D reflects the
finished dimension. Due to the variation in
countertop materials, it is recommended
to first undercut this dimension, and then
adjust it upon installation of the cooktop.
36 (91,4) 357/8(91,1) 25 (63,5) 73/4(19,7) 35/5//6(91,3) 353/16(89,4) 351/8(89,2) 22 (55,9) 1//8(2,9) Max. 71/2(19,1)
30 (76,2) 297/8(75,9) 25 (63,5) 73/4(19,7) 291sk6(76) 293/16(74,1) 29//8(74) 22 (55,9) 11/8(2,9) Max. 71/2(19,1)
All dimensions arestated in inches and (cm).
NOTE: Wiring diagrams for this cooktop are enclosed in this booklet
Printed in China
318205459 (1307) Rev.A
English - pages 1-8
Espaflol - p_iginas 9-16
Francais - pages 17-23
Wiring Diagram page- 24
For Installation with the optional Stainless Steel Backsplash.
Gas Cooktop Dimensions
* 30" (76,2 cm) min. for
unprotected cabinet and
24" (61 cm) min. for cabinet
with protected bottom surface.
30"(76,2 cm)
Min.*
2"(5,1 cm)
9" (22,9 cm)
Optional Stainless
Steel Backsplash
***Note: Applies only in case
of countertop backwall.
2" (5,1 cm)Dia.
Opening to route power
cable. Seal opening
routing power cable.
G
Gas Cooktop Cutout Dimensions
H
Do not slide unit into cabinet cutout.
Protruding screws on the bottom of unit
may damage the bottom front finish.
Figure 2
C
4" X 4" (10,2 cm x 10,2 cm)
opening to route gas supply.
Seal opening after routing
gas line
i
7¼" (18,4 cm)
**Note: D & E are critical to the proper
installation of the cooktop. D reflects the
finished dimension. Due to the variation in
countertop materials, it is recommended to
first undercut this dimension, and then adjust
it upon installation of the cooktop.
36 (91,4) 357/8(91,1) 25 (63,5) 73/4(19,7) 351s//6(91,3) 353//6(89.4) 351/8(89,2) 22 (55,9) 11/8(2,9) Max. 71/) (19,1)
30 (76,2) 297/8(75,9) 25 (63,5) 73/4(19,7) 29/5/16(76) 293/16(74,1) 29//8(74) 22 (55,9) 11/8(2,9)Max. 71/)(19,1)
351s//6(91,3)
29/5/16(76)
All dimensions arestated in inches and (cm).
Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the cooktop.
2. Remove all packing material before connecting the
electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Besure to leave these instructions with the consumer.
5. Note: For operation at 2000 ft. elevations above see
level, appliance rating shall be reduced by 4 percent
for each additional 1000 ft.
Important Note to the Consumer
Keep these instructions with your Use and Care Guide for
future reference.
Depth Adjustment Filler Kit
This cooktop isdesigned to replace existing unit. If the
depth of your countertop opening is bigger than 71/4"
(18.4cm) and lessthan 81/2'` (21.6cm) you can order a free
filler kit by calling Service Center at 1-877-4ELECTROLUX
(1-877-435-3287).
For 36" model: #903051-9010
For 30" model: #903051-9100
Optional Items Available:
• A 9" (22.9cm) Stainless Steel Backsplash Kit
#903048-9010 for 36" model or #903048-9100 for 30"
model.
• A Black Knobs Kit #903049-9120 for 36" model or
#903049-9110 for 30" model.
Those kits can be order through the Service Center at
1-877-4ELECTROLUX(1-877-435-3287). However all cost
related to those kits will be at customer charges.
IMPORTANT SAFETY
INSTRUCTIONS
Installation of this cooktop must conform with local
codes or, in the absence of local codes, with the National
Fuel Gas Code ANSI Z223.1/NFPA54--1atest edition in
the United States, or in Canada, with the Canadian Fuel
Gas Code, CAN/CGA B149 and CAN/CGA B149.2.
When installed in a manufactured (mobile) home
installation must conform with the Manufactured
Home Construction and Safety Standard, title 24 CFR,
part 3280 [Formerly the Federal Standard for Mobile
Home Construction and Safety, title 24, HUD (part
280)] or, when such standard is not applicable, the
Standard for Manufactured Home Installation, ANSI/
NCSBCSA225.1 or with local codes where applicable.
This cooktop has been design certified by CSA
International. As with any appliance using gas and
generating heat, there are certain safety precautions you
should follow. You will find them in the Use and Care
Guide, read it carefully.
Air curtain or other overhead hoods, which operate
by blowing a downward air flow on to a range, shall
not be used in conjunction with gas ranges other
than when the hood and range have been designed,
tested and listen by an independent test laboratory
for use in combination with each other,
Be sure your cooktop is installed and grounded
properly by a qualified installer or service
technician,
This cooktop must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA
No, 70--latest edition in the United States, or in
Canada, with the Canadian Electrical Code, CSA
C22,1 Part 1,
The burners can be lit manually during an
electrical power outage, To light a burner, hold a
lit match to the burner head, then slowly turn the
Surface Control knob to LITE, Use caution when
lighting burners manually,
Do not store items of interest to children in
cabinets above the cooktop, Children could be
seriously burned climbing on the cooktop to reach
items.
To eliminate the need to reach over the surface
burners, cabinet storage space above the burners
should be avoided,
Adjust surface burner flame size so it does not
extend beyond the edge of the cooking utensil,
Excessiveflame is hazardous.
Never use your cooktop for warming or heating
the room. Prolonged use of the cooktop without
adequate ventilation can be hazardous.
Do not store or use gasoline or other flammable
vapors and liquids near this or any other
appliance, Explosions or fires could result.
The electrical power to the cooktop
must be shut off while gas line connections are
being made, Failure to do so could result in serious
injury or death,
3
13"(33cm)max.depth
forcabinetinstalledabove
cooktop
30"(76,2cm)Min.
ClearanceBetweenthe
TopoftheCooking
PlatformandtheBottom
ofanUnprotectedWood
orMetalCabinet "_.
24" (61 cm)Min.
when Bottom of Wo_
or Metal Cabinet v ,
is Protected by Not
LessThan 1/8" Flame
Retardant Millboard
Covered With Not
LessThan No. 28 MGS
Sheet Steel, 0,01 5"
(0,4 mm) Stainless
Steel, 0,024" (0,6 mm)
Aluminum or 0,020"
(0,5 mm) Copper
18" (45,7 cm)
Min.
2" (5,1 cm) min. distance
between rear edge
of cutout and nearest
combustible surface
above countertop
30" (76,2 cm) min.
clearance between
the top of the
cooking platform and
the bottom of an
unprotected wood or
metal cabinet.
24" (61,X_cm_ l
It is not recommended to use
drawer underneath cooktop.
To eliminate the risk of burns
or fire from reaching over heated surfaces,
cabinet storage space located above the
cooktop should be avoided. If cabinet
storage is provided, risk can be reduced
by installing a range hood that projects
horizontally a minimum of 7" (17,8 cm) 36"(91,4cm) 36" (91,4cm)
beyond the bottom of the cabinets. 30"(76,2cm) 30" (76,2cm)
9" (22,9 cm) 9" (22,9 cm)
5" (12,7 cm) 5" (12,7 cm)
Figure 3 - CABINET DESIGN
Wall Outlet Location
_. 4 ,,_
(10,2 cm)
(12,7 cm)
Recommended
area for 120V
grounded
outlet on rear _L_cENTRE 16"
wall. _LINE (40,6 cm)
OF UNIT
/
NOTE: If an : /
outlet is not I
L
available, have
one installed I
by a qualified i
technician. ____
"_ CCENTR E
][,..LINE
Figure 4 OFUNIT
Provide an Adequate Gas Supply
This cooktop is designed to operate on natural gas at 4"
(10,2 cm) of manifold pressure only.
A pressure regulator is connected in series with the
manifold on the cooktop and must remain in series with
the supply line.
For proper operation, the maximum inlet pressure to
the regulator must be no more than 14" (35,6 cm) of
water column (W.C.) pressure.
For checking the regulator, the inlet pressure must be at
least 1"(2,5 cm) (or 2,5 kPa) greater than the regulator
manifold pressure setting. The regulator is set for 4"
(10,2 cm) of manifold pressure, the inlet pressure must
be at least 5" (12,7 cm).
The gas supply line to the range should be 1/2" (1,3 cm)
or 3/4" (1,9 cm) pipe.
LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
A kit for converting to LPgas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANEGAS
CONVERSION".
The conversion must be performed by a qualified service
technician in accordance with the kit instructions and
all local codes and requirements. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in serious personal injury and
property damage.
Important: Remove all packing material and literature
from cooktop before connecting gas and electrical
supply to cooktop.
Install Pressure Regulator
Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position
where you can reach the access cap.
Do not make the connection too tight.
The regulator is die cast. Overtightening may crack the
regulator resulting in a gas leak and possible fire or
explosion.
Manual GAS FLOW Pressure
Shutoff Flare __ Flare Regulator
Valve Union Union
Nipple Flexible
Access
Off Connector
Cap
All connections must be wrench-tightened
Figure 5
Assemble the flexible connector from the gas supply pipe
to the pressure regulator in the following order:
1. manual shutoff valve
2. 1/2" (1,3 cm) nipple
3. 1/2" (1,3 cm) flare union adapter
4. flexible connector
5. 1/2" (1,3 cm) flare union adapter
6. 1/2" (1,3 cm) nipple
7. pressure regulator
Use pipe-joint compound made for use with Natural and
LP/Propane gas to seal all gas connections. If flexible
connectors are used, be certain connectors are not
kinked.
Thesupplylineshouldbeequippedwithanapproved
shutoffvalve.Thisvalveshouldbelocatedinthesame
roomasthecooktopandshouldbeinalocationthat
allowseaseofopeningandclosing.Donotblockaccess
totheshutoffvalve.Thevalveisforturningonor
shuttingoffgastotheappliance.
Open position
Figure 6
Once the regulator is in place, open the shutoff valve in
the gas supply line. Wait a few minutes for gas to move
through the gas line.
Check for leaks. After connecting the cooktop to the
gas supply, check the system for leaks with a manometer.
If a manometer is not available, turn on the gas supply
and use a liquid leak detector (or soap and water) at all
joints and connections to check for leaks.
Do not use a flame to check for leaks
from gas connections. Checking for leaks with a flame
may result in a fire or explosion.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment of control knob valves after
connecting the cooktop to the gas supply to be sure the
cooktop manifold pipe has not moved. A misalignment
could cause the valve stems to rub on the control panel,
resulting in a gas leak at the valve.
Disconnect this cooktop and its individual shutoff
valve from the gas supply piping system during any
pressure testing of that system at test pressures greater
than 1/2 psig (3,5 kPa or 14" (35,6 cm) water column).
Isolate the cooktop from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3,5 kPa or 14" (35,6 cm) water column).
Electrical Requirements
120 volt, 60 Hertz, properly grounded branch circuit
protected by a 15 amp circuit breaker or time delay fuse.
Do not use an extension cord with this cooktop.
Grounding Instructions
IMPORTANT Pleaseread carefully.
For personal safety, this appliance must be properly
grounded.
The power cord of this appliance isequipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle (see Figure 7) to
minimize the possibility of electric shock hazard from the
appliance.
The wall receptacle and circuit should be checked by
a qualified electrician to make sure the receptacle is
properly grounded.
Preferred Method
Grounding type
wall receptacle
Power supply
cord with 3=prong
grounding plug.
Figure 7
Where a standard 2-prong wall receptacle is installed,
it is the personal responsibility and obligation of the
consumer to have it replaced by a properly grounded
3-prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.
Cooktop Installation
1. Visually inspect the cooktop for damage.
2. If you are installing the optional Stainless Steel
backsplash, first fix it at the back of the cooktop
using the screws supplied with the kit and follow the
instructions attached.
3. Set the cooktop into the countertop cutout.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.
6
Check Operation
RefertotheUse and Care Guide packaged with the
appliance for operating instructions and for care and
cleaning of your cooktop.
Do not touch the burners. They may be
hot enough to cause burns.
1. Check Burner Cap Placement
Regular burner
It is very important to be sure that all surface burner
caps and burner grates are properly installed and in the
correct locations before operating the appliance. Please
note that the burner heads are secured to the cooktop.
The cooktop is not removable. Do not attempt to remove
or lift the cooktop.
_To prevent flare-ups and avoid creation
of harmful by-products, do not use the cooktop without
all burner caps properly installed to insure proper ignition
and gas flame size.
Always keep the burner caps and burner grates in place
whenever the surface burners are in use. DO not allow
spills, food, cleaning agents or any other material to
enter the gas orifice holder openings.
Check and be sure the size of each burner cap matches
the size of the burner head. Check and be sure that all
round style burner caps are correctly in place on round
burner heads.
Check and be sure that all oval style burner caps are
correctly in place on oval burner heads (if equipped).
Check and be sure that all dual or twin style burner caps
are correctly in place on dual or twin heads (if equipped).
On round style burners, the burner cap lip (Figure 8)
should fit snug into the center of burner head and be
level. Refer to figures 9 & 10 for correct and incorrect
burner cap placement.
Once in place, you may check the fit by gently sliding
the burner cap from side to side (Figure 11) to be sure it
is centered and firmly seated. When the burner cap lip
makes contact inside the center of the burner head you
will be able to hear the burner cap click. Please note that
the burner cap should NOT move off the center of the
burner head when sliding from side to side.
Burner
Head
Fig. 8
Correct Incorrect
Burner Cap Burner Cap
Placement Placement
Fig. 9 A Fig. 10
Fig. 11
Dual Flame burner (if equipped)
Remove all tapes from burner cap Be sure that the dual
flame burner caps are correctly placed BEFOREusing
your cooktop.
Note: There are no burner adjustments necessary on this
cooktop.
Burner Cap
Burner Simmer
Precision Flame
Figure 12
Burner
Head
7
2,Turnon ElectricalPowerandOpenMainShutoff
Gas Valve
3. Check the Igniters
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks and range has been connected to
electric power.
a. To check for proper lighting, push in and turn a surface
burner knob to the LITE position. You will hear the
igniter sparking.
b. The surface burner should ignite when gas is available to
the burner. Purge air from supply lines by leaving knob
in the LITE position until burner ignites. Each burner
should light within four (4) seconds in normal operation
after air has been purged from supply lines.
c. Visually check that burner has aflame, Once the
burner ignites, the control knob should be turned out
of the LITEposition.
d. Try each surface control knob separately until all
burner valves have been checked. Each burner
location is equipped with a separate electrode.
4. Adjust the "LOW" Setting of Surface Burner Valves
(linear flow)
Testto verify if LOW setting should be adjusted:
a. Push in and turn control to LITE until burner ignites.
b. Push in and quickly turn knob to lowest position.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. Insert a thin-bladed screwdriver into the hollow valve
stem and engage the slotted screw inside. Flame size
can be increased or decreased with the turn of screw.
Turn counterclockwise to increase flame size. Turn
clockwise to decrease flame size (Figure 13).
Adjust flame until you can quickly turn knob from
LITEto lowest position without extinguishing the
flame. Flame should be as small as possible without
extinguishing.
When All Hookups are Complete
Make sure all controls are left in the OFFposition.
Before You Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your Use and Care Guide.
It may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to your Use and Care Guide for Electrolux Service
phone numbers, or call 1-877-4ELECTROLUX (1-877-
435-3287).
Valve
Stem
Figure 13
Loading...