D-Link DO-524 installation Guide
This product can be set up usingThis product can be set up using
This product can be set up using
This product can be set up usingThis product can be set up using
anan
y curry curr
enen
an
y curr
anan
y curry curr
Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape
Internet Explorer 6 or Netscape
Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape
Navigator 6.2.3.Navigator 6.2.3.
Navigator 6.2.3.
Navigator 6.2.3.Navigator 6.2.3.
t web brt web br
en
t web br
enen
t web brt web br
owserowser
owser
owserowser
, i.e, i.e
, i.e
, i.e, i.e
.,.,
.,
.,.,
AirAir
Plus G 802.11g/2.4GHzPlus G 802.11g/2.4GHz
Air
Plus G 802.11g/2.4GHz
AirAir
Plus G 802.11g/2.4GHzPlus G 802.11g/2.4GHz
DI-524
TMTM
TM
TMTM
Wireless RouterWireless Router
Wireless Router
Wireless RouterWireless Router
Before You Begin
1.1.
1. If you purchased this router to share your high-speed Internet connection with other
1.1.
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2.2.
2. It’s best to use the same computer that is connected to your modem for configuring
2.2.
the DI-524 AirPlus G Wireless Router. The DI-524 acts as a DHCP server and will
assign all the necessary IP address information on your network. See Appendix at
the end of this Quick Installation Guide or the Manual on the CD-ROM for
setting each network adapter to automatically obtain an IP address.
Check Your Package Contents
DI-524 AirPlus G 802.11g/2.4GHz Wireless
Router
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP/Straight Through) Cable
Using a power supply with
5V DC Power Adapter
If any of the above items are missing, please contact your reseller.
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice. DI-524. 11142003
1
a different voltage rating will
damage and void the warranty
of this product.
Connecting The DI-524 Wireless Router
To Your Network
A. First, connect the power adapter to the receptor at the back panel of the
DI-524 and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED lights up indicating proper operation.
B. 1. Power off your Cable or DSL modem; devices that do not have a on/off switch and
will require you to unplug the power adapter. Now, the DI-524 should be powered on
and the Cable / DSL modem should be turned off.
Cable / DSL modem (Power Off) – DI-524 (Power On)
2. Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL
modem. After the Ethernet cable is securely connected, power on the Cable / DSL
modem by turning on the unit or plugging in the power adapter.
Cable / DSL modem (Power On) – DI-524 (Power On)
3. Insert the other end of the Ethernet cable to the WAN PORT on the back panel of
the DI-524. The WAN LED light will illuminate to indicate proper connection. If the
WAN LED is not illuminated, please go back to step B1 and repeat the steps.
C. Insert an Ethernet cable to LAN Port 1 on the back panel of the DI-524 and an
available Ethernet port on the network adapter in the computer you are using to
configure the DI-524. The LED light for LAN Port 1 illuminates to indicate proper
connection. (Note: The LAN Ports on the DI-524 are Auto-MDI/MDI-X. Meaning you
can use a straight-through or crossover-Ethernet cable in the LAN Ports.)
D. Computers equipped with 802.11g wireless adapters will be able to connect to the
DI-524. The DWL-630 AirPlus G Wireless Cardbus Adapter and the DWL-510
AirPlus G Wireless PCI Adapter will be able to connect out of the box with the
router using their default wireless settings.
D. Antenna
Used to
wirelessly
connect to
802.11g or
802.11b
adapters.
C. LAN PORTS
These are the
connections for Ethernet
cables to Ethernet
enabled computers.
Reset Button
Pressing this button restores the Router to its original
factory default settings.
B. WAN PORT
This is for the connection
of an Ethernet cable to the
Cable or DSL modem.
A. Receptor for
Power Adapter.
2
Restart Your Computer
Connecting Additional Computers
To The DI-524
Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped
computers to the remaining Ethernet LAN ports on the back panel of the DI-524.
WLAN LED – a solid light
Status LED – a blinking light
indicates that the DI-524 is
functioning properly.
Power LED – a solid
light indicates a proper
connection to the power
supply.
When you have completed the steps in this Quick Installation Guide, your connected
network should look similar to this:
indicates that the wireless
segment is ready. This LED
blinks during wireless data
transmission.
LOCAL NETWORK LEDs – a
solid light on the port indicates
a connection to an Ethernet
enabled computer on ports 1-4.
This LED blinks during data
transmission.
WAN LED – a solid light
indicates connection on
the WAN port. This LED
blinks during data
transmission.
3
Using The Setup Wizard
Open your Web browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
The logon pop-up screen will appear.
Type “admin” for the username and
leave the password field blank.
Click OK
Once you have logged in, the
Home screen will appear.
Click Run Wizard
4
Loading...