Denon DRM-555 User Manual

STEREO CASSETTE TAPE DECK

DRM-555

OPERATING INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONES DE OPERACION

PRECISION AUDIO COMPONENT/CASSETTE TAPE DECK DRM-555

REMOTE SENSOR

L R

-40 +10-30 +5-20 +3-10 +1-5 0-3 -1

‚¤‚‚

PLAY

2 STOP 3 REC PAUSE

REC/REC MUTE

PHONES

RESET

INPUT LEVEL

EJECT

¢ON £OFF

COUNTER MEMORY

MPX

B OFF C

DOLBY NR

REC OFF PLAY.

TIMER

REV.MODE

PHONE LEVEL

MIN MAX

+ LEFT RIGHT

BIAS FINE BALANCE

DIRECTION

CD SYNCHRO REC

AUTO REVERSE

HIGH SPEED DUBBING SYSTEM

FOR ENGLISH READERS PAGE 05 ~ PAGE 16 POUR LES LECTEURS FRANCAIS PAGE 17 ~ PAGE 28 PARA LECTORES DE ESPAÑOL PAGINA 29 ~ PAGINA 37

IMPORTANT TO SAFETY

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Please, record and retain the Model name and serial number of your set shown on the rating label. Model No. DRM-555 Serial No.

CAUTION:

1. Handle the power supply cord carefully

Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

2. Do not open the top cover

In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON DEALER.

3. Do not place anything inside

Do not place metal objects or spill liquid inside the cassette tape deck. Electric shock or malfunction may result.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

• FOR U.S.A. & CANADA MODEL ONLY

CAUTION

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

• POUR LES MODELES AMERICAINS ET CANADIENS UNIQUEMENT

ATTENTION

POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Water and Moisture – The appliance should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.

6. Carts and Stands – The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart

combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8. Ventilation – The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9. Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10. Power Sources – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11. Grounding or Polarization – Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

12. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

14. Cleaning – The appliance should be cleaned only as recommended by the manufacturer.

15. Power Lines – An outdoor antenna should be located away from power lines.

16. Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

17. Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

18. Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

19. Damage Requiring Service – The appliance should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

appliance; or C. The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or

exhibits a marked change in performance; or E. The appliance has been dropped, or the enclosure

damaged.

20. Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

ENGLISH FRANCAIS ESPAÑOL

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO

• Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack.

• Eviter des températures élevées Tenir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère.

• Evite altas temperaturas. Permite la suficiente dispersión del calor cuando está instalado en la consola.

• Keep the set free from moisture, water, and dust.

• Protéger l’appareil contre l’humidité, l’eau et lapoussière.

• Mantenga el equipo libre de humedad, agua y polvo.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans l’appareil.

• No deje objetos extraños dentro del equipo.

• Do not let insecticides, benzene, and thinner come in contact with the set.

• Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

• No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.

• Never disassemble or modify the set in any way.

• Ne jamais démonter ou modifier l’appareil d’une manière ou d’une autre.

• Nunca desarme o modifique el equipo de ninguna manera.

• Unplug the power cord when not using the set for long periods of time.

• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

• Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.

* (For sets with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• No obstruya los orificios de ventilación.

• Handle the power cord carefully. Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon.

• Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.

ENGLISH

Thank you very much for purchasing the DENON component stereo cassette tape deck. DENON proudly presents this advanced tape deck to audiophiles and music lovers as a further proof of DENON’s non-compromising pursuit of the ultimate in sound quality. The high quality performance and easy operation are certain to provide you with many hours of outstanding listening pleasure.

— TABLE OF CONTENTS —

FEATURES ……………………………………………………………………………5 CONNECTION ………………………………………………………………………5 NAMES AND FUNCTIONS OF PARTS …………………………………………6, 7 CASSETTE TAPES ……………………………………………………………………7 AUTOMATIC TAPE SELECTION ……………………………………………………8 PLAYBACK …………………………………………………………………………8, 9

MUSIC SEARCH SYSTEM ………………………………………………………9

RECORDING …………………………………………………………………………10

PROPER RECORDING LEVEL …………………………………………………10 RECORDING BIAS ADJUSTMENT ……………………………………………11

REC/REC MUTE AND REC PAUSE BUTTON ………………………………11 DIMMER ADJUSTMENT …………………………………………………………11 SYNCHRONIZED RECORDING FUNCTION ……………………………………12 TAPE COUNTER AND MEMORY STOP …………………………………………13 TIMER RECORDING/PLAYBACK …………………………………………………14 DOLBY B AND C NOISE REDUCTION SYSTEM ………………………………15 DOLBY HX-PRO HEADROOM EXTENSION SYSTEM …………………………15 MAINTENANCE ……………………………………………………………………15 TROUBLESHOOTING ………………………………………………………………16 SPECIFICATIONS ……………………………………………………………………16

Please check to make sure the following items are included with the main unit in the carton:

(1) Operating Instructions …………………………………………………1 (2) Connection Cords ………………………………………………………2 (3) Mini-Plug Cable …………………………………………………………1

FEATURES

2 Computer Controlled Mechanism 2 Dual Power Supply 2 Dolby HX-Pro Headroom Extension System 2 Dolby B & C Noise Reduction Systems 2 Manual Bias Adjustment Control 2 Computing Tape Counter with 4-Digit Readout and Memory Stop 2 Music Search System 2 FL Peak Level Meters 2 Auto Tape Selector 2 Synchronized Recording 2 Timer Play and Timer Recording 2 Optional Remote Controllable

CONNECTION

• Leave your entire system (including this cassette deck) turned off until all connections between the deck and other components have been completed.

VOLTAGE SELECTOR

115V 230V

PRESET

LINE OUT

LINE

SYNCHRO

TAPE-1

REC

L R

LINE

OUT IN

Receiver or amplifier

This jack is for the synchronized recording function only. Do not plug in microphones, headphones nor other plugs.

Power supply outlet.

60 Hz

DRM-555

Connecting the Deck to an Amplifier

• Before connecting the deck to your amplifier, please review your amplifier’s instruction manual.

• Use the white plugs for the left channel and red plugs for the right channel.

2 Tape Dubbing

• Many stereo amplifiers and receivers have tape dubbing circuitry so that tape duplication can be performed between two or more tape decks. Review your amplifier’s instruction manual for a full explanation of this mode of operation.

2 Connecting Headphones

To listen through headphones, plug your headphones into the PHONES jack.

2 Installation Precautions

If the deck is placed near an amplifier, TV or tuner, noise (induced hum) or beat interference may result, especially during FM or AM reception. If this occurs, place the deck further away from other components or reorient its position.

Caution:

A mechanical sound is heard the first time the power switch is set to “ON” after the power cord is plugged into an outlet. This is the sound of the cassette mechanism being set to the proper operating state, and is normal. (When using an AC outlet on a receiver or amplifier, used an “UNSWITCHED” outlet.)

WHITE

RED

ENGLISH

NAMES AND FUNCTIONS OF PARTS

Power Operation Switch (¢ ON £ OFF)

• Press once to turn the power to deck on, and once more to turn the

power off.

• The deck remains in a stand-by (non-operative) mode for

approximately 2 seconds after it is switched on.

Eject Button (EJECT 5 )

• Press this button to open the cassette compartment cover. When the

tape is running, press the Stop button (

2 STOP) first to stop tape

transport, then press the Eject button (EJECT

5).

Timer Switch (TIMER)

• This switch is provided for use with an optional audio timer for

unattended recording or morning-alarm playback.

• For non-timer operation, this switch should be set in the “OFF”

position. See page 14.

Cassette Compartment Cover

• If the cover is not closed completely, the tape transport buttons will

remain inoperative.

Remote Sensor (REMOTE SENSOR)

• With the cassette deck the remote control unit is not included.

• Each of “Play, Fast Forward, Fast Rewind, Stop, Rec Pause and

Rec/Rec Mute” functions can be remote controlled with wireless handset of the receiver (DRA Series receivers). For details refer to the DRA Series operating instructions.

Counter Memory Button (MEMORY)

• When this button is pressed during forward tape travel ( ), fast rewinding (

6 ) will stop automatically at the tape counter position

“‚‚‚‚”.

• When this button is pressed during reverse tape travel ( ), fast forwarding (

7 ) will stop automatically at the tape counter position

“‚‚‚‚”. See page 13.

Counter Reset Button (RESET)

• Press this button to reset the tape counter to zero.

MPX Filter Button (MPX)

• The MPX Filter button (MPX) should be used to prevent interference with the Dolby NR circuit when making Dolby NR encoded recordings of FM stereo programs.

• When making Dolby NR encoded recordings from any program source other than FM stereo, leave this button in the “OFF” position.

Input Level Control (INPUT LEVEL)

• This knob adjusts the recording input level. It affects the level in both channels. See page 10.

Balance Control (BALANCE)

• This is the knob to adjust the recording level balance between the left and right channels. Turn it counter-clockwise to reduce the right channel’s level and clockwise to reduce the left channel’s. Usually, put the knob at the center click position.

Bias Fine Control (BIAS FINE)

(For Normal, CrO2 and Metal tape)

• Use this control to fine-adjust the bias. Standard bias is obtained at the center click-stop position. See page 11.

Phone Level Control (PHONE LEVEL)

• Head phone output level is adjusted by this knob. The levels in the left and right channels can be changed simultaneously.

Headphone Jack (PHONES)

• For private music enjoyment without disturbing others, or for monitoring a recording, a headphone set may be connected to this jack. Use a headphone with an impedance rating of 8 to 1200 Ω/ohms.

PRECISION AUDIO COMPONENT/CASSETTE TAPE DECK DRM-555

REMOTE SENSOR

L R

-40 +10-30 +5-20 +3-10 +1-5 0-3 -1

‚¤‚‚

PLAY

2 STOP 3 REC PAUSE

REC/REC MUTE

PHONES

RESET

INPUT LEVEL

EJECT

¢ON £OFF

COUNTER MEMORY

MPX

B OFF C

DOLBY NR

REC OFF PLAY.

TIMER

REV.MODE

PHONE LEVEL

MIN MAX

+ LEFT RIGHT

BIAS FINE BALANCE

DIRECTION

CD SYNCHRO REC

AUTO REVERSE

HIGH SPEED DUBBING SYSTEM

we r t y

i!2

!6 !5

Caution:

Whenever the Power Operation switch is in the OFF state, the apparatus is still connected on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation.

Display

Dolby NR Switch (DOLBY NR)

• To record or playback tapes with Dolby B or C-type noise reduction, set this switch to “B” or “C”. Turn it “OFF” when not using the Dolby NR system.

Reverse Mode Switch (REV. MODE)

• Select the type of tape transport. The reverse mode can be set to

(one side), (continuous playback).

ENGLISH

Display

• Indicators with an encircled number light up when the corresponding button is pressed.

L R

-40 +10-30 +5-20 +3-10 +1-5 0-3 -1

SYNCMPX

MEMO

Peak Level Meter

MPX Filter Indicator

Remote Control Indicator

Indicates the recording and playback signal levels for the left and right channels.

Tape Transport Indicators

Memory Indicator

Tape Counter

Synchro Rec Indicator (See page 12)

CASSETTE TAPES

2 Handling Precautions

• C-120 cassette tapes C-120 cassette tapes are not recommended as they use a very thin tape base which may become tangled around the capstan or pinch roller.

• Tape Slack Before putting a tape into the deck, take up any slack with a pencil or your finger tip. This precaution prevents the tape from becoming entangled around the capstan or pinch roller.

2 Storage Precautions

• Do not store cassette tapes in a place where they will be subject to:

• Extremely high temperature or excessive moisture

• Excessive dust

• Direct sunlight

• Magnetic fields (near TV sets or speakers)

• To eliminate tape slack, store your cassettes in cassette cases with hub stops

2 Accidental Erasure Prevention

• All cassettes have erasure prevention tabs for each side. To protect valuable recordings from accidental or inadvertent erasure, remove the tab for the appropriate side with a screwdriver or another tool.

• To record on a tape whose erasure prevention tabs have been removed, cover the tab holes with adhesive tape.

Erasure prevention tab for side B

Erasure prevention tab for side A

Tape Transport Buttons

Play Button

Stop Button

Fast Rewind Button

Fast Forward Button

Rec/Rec Mute

Button

Rec Pause Button

Direction Button

Press to playback tape.

Press to stop the tape in any mode.

Press for fast rewind.

Press for fast forwarding.

Press the Rec/Rec Mute button (REC/REC MUTE) (

4 ) and Play button (PLAY) simultaneously to

start recording. If only the Rec/Rec Mute button (REC/REC MUTE) (

4 ) is pressed, the deck enters

the recording pause mode. Pressing this button in the recording pause mode will start Auto Rec Mute, and a 5-second silent space is recorded onto the tape.

Press this button to enter the recording pause mode from the recording or recording mute mode. This button can only be used during recording.

Changes the tape transport direction from forward “

1” to reverse “0”, and vice versa.

PLAY

2 STOP

3 REC PAUSE

Side A

ENGLISH

PLAYBACK

q Press the Power Operation switch to the ¢ ON position. w Press the Eject button (EJECT

5 ) to open the cassette compartment

cover.

e Load the cassette tape and close the cassette compartment cover. r When listening to a tape that has been recorded with Dolby noise

reduction, set the Dolby NR switch (DOLBY NR) to match the system used at the time of recording.

B OFF C

DOLBY NR

t Press the Direction button ( 01) to select the direction of tape transport.

IndicatorTransport Direction

Forward

Reverse

• Switch on your amplifier or receiver.

• Set the Tape Monitor switch on your amplifier or receiver to the TAPE position.

• The numbers in the illustration below depict the order in which operation steps are carried out.

PRECISION AUDIO COMPONENT/CASSETTE TAPE DECK DRM-555

REMOTE SENSOR

L R

-40 +10-30 +5-20 +3-10 +1-5 0-3 -1

‚¤‚‚

PLAY

2 STOP 3 REC PAUSE

REC/REC MUTE

PHONES

RESET

INPUT LEVEL

EJECT

¢ON £OFF

COUNTER MEMORY

MPX

B OFF C

DOLBY NR

REC OFF PLAY.

TIMER

REV.MODE

PHONE LEVEL

MIN MAX

+ LEFT RIGHT

BIAS FINE BALANCE

DIRECTION

CD SYNCHRO REC

AUTO REVERSE

HIGH SPEED DUBBING SYSTEM

AUTOMATIC TAPE SELECTION

This Stereo Cassette Deck contains an automatic tape selector which automatically selects the optimum bias and equalization for the tape in use. This is accomplished by detection of the tape type detections holes in the cassette housing.

• If a tape without tape type detection holes is used, the deck will be set for normal tapes.

Detection holes for metal tape

Detection holes for chrome tape

ENGLISH

y Select the type of tape transport with the Reverse Mode switch (REV.

MODE).

REV.MODE

Switch positionMode

To listen to one side only

To listen to repeat playback of both sides

u Press the Play button (PLAY) to begin playback. i Press the Stop button (

2 STOP) to stop the playback.

• In the continuous playback mode (Reverse Mode switch (REV. MODE) set to ), playback of both tape sides will be repeated 5 times and then stop automatically.

• If different types of Dolby noise reduction are used for record and playback, playback response will be adversely effected.

• When power is turned off during tape transport, it may not be possible to remove the cassette by pressing the Eject button (EJECT

5 ).

In this case, turn on power again before you press the Eject button (EJECT

5 ).

2 MUSIC SEARCH SYSTEM

The music search system detects blank sections (lasting for at least 4 seconds) between selections in order to locate the beginning of selections in the forward or reverse direction.

1. To advance from the current selection to the beginning of the next selection (CUE): Press the Play button (PLAY), and press the Fast Forward button (

7 )

when the tape is travelling in the forward ( ) direction. Press the

Play button (PLAY)

, and press the Fast Rewind button (

) when the tape is travelling in the reverse ( ) direction. The tape transport indicator flashes. The deck will skip the rest of the current selection and automatically resume play from the beginning of the next selection.

2. To repeat playback from the beginning of the current selection (REVIEW): Press the

Play button (PLAY)

, and press the Fast Rewind button ( 6 ) when the tape is travelling in the forward ( ) direction. Press the Play button (PLAY), and press the Fast Forward button (

7 )

when the tape is travelling in the reverse ( ) direction. The tape transport indicator flashes. The deck will rewind the tape to the beginning of the current selection and automatically resume play from that point. This is very convenient for repeating playback of the current selection.

Notes on Music Search Operation:

The search functions operates by detecting comparatively long, blank sections approximately 4 to 5 seconds long, in between recorded selections. Therefore, the system may not operate normally in the following cases:

• Recordings with discontinuous speech or conversation.

• Recordings with long periods of pianissimo (softly played music).

• Recordings with long silences.

• Blank sections with a high level of noise.

• Blank sections shorter than 4 seconds.

• If noise-emitting appliances, such as electric razors, drills, refrigerators, etc., are operated nearby.

• REV. close to the beginning of the program or CUE close to the ending.

ENGLISH

RECORDING

q Press the Power Operation switch to the ¢ ON position. w Load the cassette tape.

(Check that the erasure prevention tabs of the cassette housing have not been broken off.)

e Move the Dolby NR switch (DOLBY NR) and select the Dolby NR type that

suits the recording.

B OFF C

DOLBY NR

r Press the Direction button ( 01) to select the direction of tape transport. t Select the type of tape transport with the Reverse Mode switch (REV.

MODE).

Switch positionMode

To record on only one side

To continuously record on both sides

y Press the Rec/Rec Mute button (REC/REC MUTE) ( 4 ) to set the recording

pause mode. The

43indicator will light up.

u Adjust the recording level with the Input Level control (INPUT LEVEL)

while watching the Peak Level Meter.

i Press the Play button (PLAY) to start the recording.

The play ( or ) and the

4 indicator will light during recording.

o To pause the recording, press the Rec Pause button (

3 REC PAUSE).

Press the Play button (PLAY) to resume recording.

!0 To stop recording, press the Stop button (

2 STOP).

Caution:

• Be careful not to erase important recordings by mistake. Inadvertent start of recording will happen in the following cases:

1. If the Play button (PLAY) is pressed while the

4 indicator lights, recording

starts.

If the Play button (PLAY) and Rec/Rec Mute button (REC/REC MUTE)

( 4 ) are pressed at the same time, recording starts. The best way to avoid accidental erasure is to break off the two erasure prevention tabs on the cassette housing.

2 PROPER RECORDING LEVEL

A too high recording level can saturate the tape and cause distortion. On the other hand, if the recording level is set too low, soft passages will be marked by residual noise. A proper recording level is the single most important factor for making well balanced recordings.

Guideline for maximum recording level

0 dB level on peaks

+1 dB level on peaks

+3 dB level on peaks

TYPE

I (Normal) TYPE II (CrO2) TYPE IV (Metal)

Note: The optimum recording level differs depending on the program source

and the type of tape used.

• Switch on your amplifier or receiver and the source component.

• Set the Tape Monitor switch on your amplifier or receiver to the SOURCE position.

PRECISION AUDIO COMPONENT/CASSETTE TAPE DECK DRM-555

REMOTE SENSOR

L R

-40 +10-30 +5-20 +3-10 +1-5 0-3 -1

‚¤‚‚

PLAY

2 STOP 3 REC PAUSE

REC/REC MUTE

PHONES

RESET

INPUT LEVEL

EJECT

¢ON £OFF

COUNTER MEMORY

MPX

B OFF C

DOLBY NR

REC OFF PLAY.

TIMER

REV.MODE

PHONE LEVEL

MIN MAX

+ LEFT RIGHT

BIAS FINE BALANCE

DIRECTION

CD SYNCHRO REC

AUTO REVERSE

HIGH SPEED DUBBING SYSTEM

ENGLISH

2 RECORDING BIAS ADJUSTMENT

For best recording results, monitoring during recording and comparing different recordings using your own judgement are essential. The DENON cassette deck is equipped with a Bias Fine control (BIAS FINE) to assist you in setting the proper bias for different types and brands of tape. At the center stop-click position, the deck is set to the reference bias level for Normal, CrO

2 and Metal tape. If the resulting recording in this

position has too much or too little high frequency content, adjusting the Bias Fine control (BIAS FINE) can be useful to achieve better results.

BIAS FINE

If the high frequencies (treble sounds) are to be boosted, turn the Bias Fine control (BIAS FINE) counter-clockwise to decrease the bias current. Turn the control clockwise to increase bias current. By the use of this control, you can record tapes with a frequency response that will perfectly match your listening taste.

Counterclockwise

FREQUENCY (Hz)

OUTPUT LEVEL (dB)

Clockwise

REC/REC MUTE AND REC PAUSE BUTTON

1. To record a 5-second blank section during recording: Press the Rec/Rec Mute button (REC/REC MUTE) (

4 ). A 5-second blank

will be recorded and the deck will enter the recording standby mode.

2. To record a 5-second blank section during the recording standby mode: Press the Rec/Rec Mute button (REC/REC MUTE) (

4 ) from the recording

standby mode. A 5 second blank will be recorded and the deck will enter the recording standby mode again.

3. To cancel recording of blank space: Press the Rec Pause button (

3 REC PAUSE). Blank space recording will be

cancelled and the deck enters the recording standby mode.

4. To extend the blank section with another 5 seconds or more: Simply press the Rec/Rec Mute button (REC/REC MUTE) (

4 ) and the blank

section will be increased with another 5 seconds.

DIMMER ADJUSTMENT

With the DRM-555, the brightness of the display can be adjusted in seven steps. To make the display brighter, press the Fast Forward button (

7 ) while holding in the Stop button ( 2 STOP).

To make the display dimmer, press the Fast Rewind button (

6 ) while holding in the Stop button ( 2 STOP).

The display is initially set to the maximum brightness.

ENGLISH

PRECISION AUDIO COMPONENT/CASSETTE TAPE DECK DRM-555

REMOTE SENSOR

L R

-40

+10-30 +5-20 +3-10 +1-5 0-3 -1

‚¤‚‚

PLAY

2 STOP 3 REC PAUSE

REC/REC MUTE

PHONES

RESET

INPUT LEVEL

EJECT

¢ON £OFF

COUNTER MEMORY

MPX

B OFF C

DOLBY NR

REC OFF PLAY.

TIMER

REV.MODE

PHONE LEVEL

MIN MAX

+ LEFT RIGHT

BIAS FINE BALANCE

DIRECTION

CD SYNCHRO REC

AUTO REVERSE

HIGH SPEED DUBBING SYSTEM

q Load the tape, the disc you want to record into the CD player. w Following the recording instructions on page 10, set the Dolby NR mode,

and the input level.

e Set the CD player to the stop or pause mode. r Press the Rec/Rec Mute button (REC/REC MUTE) (

4 ) and Rec Pause

button (

3 REC PAUSE) simultaneously. The cassette deck and CD player

are automatically set to the synchronized recording mode. The “SYNC” indicator flashes on the cassette deck and the synchronized recording mode is indicated on the CD player. (For details, refer to the CD player’s operating instructions.)

t To stop synchronized recording, press the Stop button

( 2 STOP)

on cassette deck and stop button on CD player. The synchronized recording mode is cancelled for both the cassette deck and CD player.

To stop synchronized recording temporarily, press the Stop button ( 2 STOP) on the CD player. A 5-second blank space is created on the tape, after which the recording pause mode is set. The “SYNC” indicator flashes. To resume synchronized recording, press the Play button (PLAY) on the CD player.

Notes:

• If synchronized recording is started when the CD player is in a mode other than the stop or pause mode or when no disc is set, the “SYNC” indicator on the cassette deck flashes and the recording pause mode is set until synchronized recording is possible on the CD player.

• In the synchronized recording mode, only the Stop button (

2 STOP) will

function.

Caution:

• Do not set the cassette deck to the synchronized recording mode when the CD player is in the play mode. Also, do not turn off the power of the cassette deck or the CD player during synchronized recording. Doing so can result in malfunction.

• During the editing operation, when using the editing functions on the CD player, be sure to select a tape with a sufficiently long recording time.

SYNCHRONIZED RECORDING FUNCTION

• Convenient synchronized recording can be performed when used in combination with a DENON CD player equipped for the synchronized recording function.

• Synchro jack (SYNCHRO) Connection connect the Synchro jack (SYNCHRO) with a DENON CD player which is equipped with a Synchro jack (SYNCHRO), then make a synchronized recording. Use the connection cord supplied with this cassette deck.

• Switch on your amplifier or receiver and the CD player.

• Set the Tape Monitor switch on your amplifier or receiver to the source position.

LINE OUT

LINE

SYNCHRO

LINE OUT

CD player

DRM-555

Power supply outlet

+ 28 hidden pages