Denon AVR-4306 Service Manual
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 1 / 16
The Operating Manual for
DENON AV Receiver / Amplifier firmware update.
“DENON Flash Rom Writer Compact Version.”
Model Name: AVR-4306/AVC-4320
Version:
AVR-4306 : FWCV_AVR4306_V0010
AVC-4320 : FWCV_AVC4320_V0010
Date: 2006-06-12
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 2 / 16
Index
<Notice> ....................................................................................................................................................3
1. Preparations before starting the operation........................................................................................4
1.1 Preparation for the Personal Computer.......................................................................................4
1.2 Preparations for the cables .........................................................................................................4
1.3 Connection of AV receiver/amplifier and PC................................................................................5
1.4 Install the DENON Flash ROM Writer Compact version..............................................................6
2. Firmware update procedure (In case of direct connection without hub using cross cable.)..........7
2.1 Setup the IP address PC and the AV Receiver/Amplifier.............................................................7
2.2 How to setup the fixed IP address of the AV Receiver/ Amplifier. ................................................7
2.3 Run the DENON Flash ROM Writer Compact version. ...............................................................8
2.3.1 Communication check. .............................................................................................. 8
2.3.2 Start the firmware update .......................................................................................... 9
2.3.3 Complete the firmware update. ................................................................................. 9
3. Firmwares update procedure (In case of Ethernet HUB or Router (without DHCP server ability)) .10
3.1 Setup the IP address PC and the AV Receiver/Amplifier...........................................................10
3.2 How to setup the fixed IP address of the AV Receiver/ Amplifier. ..............................................10
3.3 Run the DENON Flash ROM Writer Compact version. .............................................................11
3.3.1 Communication check. ............................................................................................ 11
3.3.2 Start the firmware update ........................................................................................ 12
3.3.3 Complete the firmware update. ............................................................................... 12
4. Firmwares update procedure. (In case of Ethernet HUB or Router (with DHCP server ability)) .....13
4.1 Setup the IP address PC and the AV Receiver/Amplifier...........................................................13
4.2 How to setup the auto IP address of the AV Receiver/Amplifier. ...............................................13
4.3 Confirm IP Address of the AV Receiver/Amplifier. .....................................................................13
4.4 Run the DENON Flash ROM Writer Compact version. .............................................................14
4.4.1 Communication check. ............................................................................................ 14
4.4.2 Start the firmware update ........................................................................................ 15
4.4.3 Complete the firmware update. ............................................................................... 15
5. Firmware update retrial procedure..................................................................................................16
6. Confirming the firmware’s number after upgraded... エラー! ブックマークが定義されていません。
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 3 / 16
<Notice>
(1)
After upgraded, the ROOM EQ setting of product (AVR-4306/AVC-4320) is initialized, so please
excute AUTO SETUP again according to the manual (attached to the product at the time of
purchase).
Please load and set USER MEMORY according to the manual (attached to the product at time of
purchase) before the upgrade when you want to leave the data of USER MEMORY. The data that
can be maintained when the upgrade is executed is only a present setting.
(2)
Please keep the following notice for firmware update.
a) Keep the PC environment refer to 1.1.
b) Don't use a wireless network. (Flat type LAN cable)
Connect it by cable.
Don’t use flat type LAN cable like the right picture.
c) Stop the resident program on PC.
(Virus checker and System check utility, etc)
d) Avoid the communication cable from the electrical noise
source.
(E.g. telephone cable, AC line, a fluorescent light)
e) Stop the screen saver ability on PC.
f) Stop the power save ability on PC.
g) In case of laptop PC, Use the AC adaptor.
h) Don’t remove cable during update.
i) Don’t turn off the power during update.
j) Don’t run other PC application during update.
k) Please power off the product (AVR-4306/AVC-4320) before upgrade.
Please power on the product according to this manual.
l) This upgrade takes almost 10 minutes from beginning to the end.
The upgrade situation is displayed the bar graph, and can confirm the status.
Please do not touch the router, working PC, the AV Receiver/amplifier, the connecting cable,
and HUB while upgrade.
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 4 / 16
1. Preparations before starting the operation
1.1 Preparation for the Personal Computer
Minimum hardware and software requirements:
Type PC/AT compatible
CPU Intel Pentium/Celeron500MHz or faster
RAM 128MB or more
Free hard disc space 25MB or more
OS Windows XP Home Edition / Professional SP2 or more
Display resolution Super VGA (800x600) or more.
Port. ETHERNET port(RJ-45)
Communication speed ETHERNET:10BASE-T/100BASE-TX
1.2 Preparations for the cables
There are three methods.
a) 10BASE-T/100BASE-TX Ethernet cross cable x 1pcs.
b) 10BASE-T/100BASE-TX Ethernet straight cable x 2pcs
and 10BASE-T/100BASE-TX Ethernet HUB or Router(w/o DHCP server).
c) 10BASE-T/100BASE-TX Ethernet straight cable x 2pcs
and 10BASE-T/100BASE-TX Ethernet HUB or Router(with DHCP server).
The Operating Manual for DENON AV Receiver/Amplifier firmware upgrade Page 5 / 16
1.3 Connection of AV receiver/amplifier and PC
You can select the following 3 methods.
Also connect the display monitor for OSD.
a) Connect the Ethernet cross cable between Ethernet port of PC and Ethernet port of AV
Receiver/Amplifier. (refer to 2)
b) Connect the Ethernet straight cable between Ethernet port of PC and Ethernet port of Hub (or
Router w/o DHCP server). And connect the Ethernet straight cable between Ethernet port of
Hub (or Router w/o DHCP server) and Ethernet port of AV Receiver/Amplifier. (refer to 3)
PC
Ethernet cross cable
AV Rec e i ver
/Amplifier
Display
C) Connect the Ethernet straight cable between Ethernet port of PC and Ethernet port of
Router( with DHCP server). And connect the Ethernet straight cable between Ethernet port of
Router( with DHCP server) and Ethernet port of AV Receiver/Amplifier. (refer to 4)
PC
PC
Ethernet
straight
cable
Ethernet
straight
cable
HUB or
Router(w/o DHCP
server)
Ethernet
straight
Router
With
DHCPserver
Ethernet
straight
AV Rec e i ver
/Amplifier
cable
AV Rec e i ver
/Amplifier
cable
Display
Display
Loading...