PAC N120
PAC N120
User manual
5
8
7
9
6
10
DESCRIPTION
ACCESSORIES
1
4
3
2
11
12
20
14
15
16
17
21
13
19
18
4
Important safeguards
• Use this appliance only as described in this instruction manual.
As with all electrical equipment, whilst the instructions aim to cover as many eventualities as
possible, caution and common sense should be applied when operating and installing this
appliance.
• This appliance is designed for home air conditioning and must not be used for other purposes.
• It is dangerous to modify or alter the characteristics of the appliance in any way.
• The appliance must be installed in conformity with national legislation regulating electrical
equipment and installations.
• If the appliance requires repair, contact a Service Centre authorised by the manufacturer only.
Repairs carried out by unauthorised personnel may be dangerous.
• This appliance must be used exclusively by adults.
• Never allow the appliance to be used by people (including children) with psychological, physical or sensory impairments or with insufficient experience and knowledge, unless closely
supervised and instructed by someone responsible for their safety.
Young children should be supervised to ensure that they do not play with the appliance.
• The appliance must be connected to an efficient earth system.
Have your electrical circuit checked by a qualified electrician.
• Do not use extension cables.
• Before cleaning or maintenance, always unplug the appliance from the mains socket.
• Never unplug the appliance by pulling on the power cable.
• Do not install the appliance in rooms containing gas, oil or sulphur. Do not install near sources
of heat.
• Keep the appliance at least 50 cm away from flammable substances (alcohol etc) or pressu
rised containers (eg aerosol cans).
• Do not rest heavy or hot objects on top of the appliance.
• Clean the air filter at least once a week.
• Avoid using heating appliances near the air conditioner.
• Always transport the appliance upright or resting on one side.
Before moving the appliance, empty the internal circuit completely of water.
After moving the appliance, wait at least 1 hour before starting it
• When putting the appliance away, do not cover with plastic bags.
• The materials used for packaging can be recycled.
You are therefore recommended to dispose of them in special differentiated waste collection
containers.
• At the end of its working life, consign the appliance to a specialist collection centre.
• If the power cable is damaged, it must be replaced by the manufacturer or an authorised
technical service centre in order to avoid all risk.
SPECIFIC WARNINGS FOR APPLIANCES WITH R410A* REFRIGERANT GAS
R410A refrigerant gas conforms to EC regulations on the environment.
Avoid perforating the refrigerant circuit of the appliance.
ENVIRONMENTAL INFORMATION: This unit contains fluorinated greenhouse gases covered by the
Kyoto Protocol. Maintenance and disposal must be carried out by qualified personnel only
(R410A, GWP=1975).
* Verify the type of refrigerant gas used in your appliance on the rating plate.
DESCRIPTION
1 air outlet grille
2 control panel
3 castors
4 handles
5 filter
6 evaporator air intake grille
7 air exhaust hose housing
8 condenser air intake grille
9 power cable
10 drainage hose
11 wall flange
12 air exhaust hose
13 hose adaptor (2 pieces)
14 accessory for wall mounting
15 window bracket grille
16 window bracket cap
17 window bracket
18 additional window bracket
19 6 screws
20 window outlet
21 remote control
5
AIR-CONDITIONING WITHOUT INSTALLATION
Just a few simple steps and your comfort is
ensured with your air conditioner:
• Screw one hose adaptor to the hose’s
end .
• Fit the other hose adaptor in the air
exhaust hose housing at the back of
the appliance (see fig. A).
• Screw the other end of the hose to the
adaptor, that was already fitted to the appliance (see fig. A).
12
7
13
13
A
Preparing for use
If you have a sash window
• Attach the window bracket grille to
the window bracket with the four
screws provided
(fig. B).
19
17
15
B
• Open the window.
• Place the window bracket in the window, extending it to fit the width of the
window
(fig. C).
17
C
D
• Once the bracket is extended, it can be
locked into his width by tightening the last
two screws provided.
• Close the window (fig. D).
• Place the air conditioner near the window. Insert the assembled exhaust hose
into the window bracket grille
(fig.
E). Make sure the air exhaust hose is unobstructed.
• When not used, the window bracket can
be closed off with the cap provided.
16
17
12
Keep the air hoses as short and free of
curves as possible to avoid constrictions.
E
ELECTRICAL CONNECTIONS
Before plugging the appliance into the mains socket, check that:
• The outlet’s power supply corresponds to the value indicated on the rating label on the back
of the appliance;
• The outlet and electrical circuit are adequate for the appliance;
• The outlet is a 3-hole grounded outlet . If this is not the case, you must choose another outlet.
Failure to follow these important safety instructions absolves the manufacturer of all liability.
The instructions below will enable you to prepare your air conditioner for operation as efficiently
as possible. Before use, make sure the air intake and outlet grilles are unobstructed.
The power cable must be replaced by a qualified professional only.
If you have a very large window
• in order to cover your window aperture,
use the additional window bracket without holes extending it to the desired
dimension, then fix the bracket by using
the pins provided. When extracting the
window bracket and joining the two
pieces pay attention you do not cover the
hole or holes (depending on the model).
Loading...