Page 1
Features
STTH16BC065C
650 V high voltage rectifier for BC2 topology
Data brief
■ high voltage rectifier
■ optimized diode for BC
■ low switching losses
■ improves efficiency by up to 2.5% compared to
2
topology (ST patent)
a conventional continuous mode PFC using
standard ultrafast 600 V PN diodes
■ efficiency performance similar to traditional
topologies using 600 V Schottky power diodes
with no reverse recovery charges used in CCM
PFC
■ provides a cost-effective solution to meet the
80+ efficiency requirements
■ supports PFC working up to 300 kHz
■ suitable for PFC up to 1 kW
■ compatible with standard PFC controller ICs
Description
The STTH16BC065C is a specific rectification
diode used in continuous mode power factor
correction working in the BC
has been specially designed for the dedicated
2
BC
topology. Its electrical characteristics were
specifically studied to optimize the
cost/performance ratio. As a result, SMPS
efficiency improvements of up to 2.5%
(comparable with topologies using SiC) can be
achieved at an optimized cost.
2
topology. This diode
A1
A2
A1
TO-220AB
STTH16BC065CT
Table 1. Device summary
Symbol Value
I
F(AV)
V
RRM
K
A2
K
2 x 8 A
650 V
November 2010 Doc ID 18195 Rev 1 1/3
For further information contact your local STMicroelectronics sales office.
www.st.com
3
Page 2
Ordering information STTH16BC065C
1 Ordering information
Table 2. Ordering information
Order code Marking Package Weight Base qty. Delivery mode
STTH16BC065CT STTH16BC065C TO-220AB 1.90 g 50 Tube
2 Revision history
Table 3. Document revision history
Date Revision Changes
05-Nov-2010 1 Initial release.
2/3 Doc ID 18195 Rev 1
Page 3
STTH16BC065C
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 18195 Rev 1 3/3
Loading...