CDIDI 1N759A, 1N758A, 1N757A, 1N756A, 1N755A Datasheet

• 1N746A-1 THRU 1N759-1 AVAILABLE IN	JAN, JANTX	AND	JANTXV		1N746	thru1N759A
PER MIL-PRF-19500/127						and
					1N746A-1	thru1N759A-1
• 1N4370A-1 THRU 1N4372A-1 AVAILABLE IN	JAN, JANTX		AND	JANTXV
						and
PER MIL-PRF-19500/127
					1N4370	thru1N4372A
• DOUBLE PLUG CONSTRUCTION						and
• METALLURGICALLY BONDED					1N4370A-1	thru1N4372A-1

MAXIMUM RATINGS

Operating Temperature: -65°C to +175°C

Storage Temperature: -65°C to +175°C

DC Power Dissipation: 500 mW @ +50°C

Power Derating: 4 mW / °C above +50°C

Forward Voltage @ 200mA: 1.1 volts maximum

ELECTRICAL CHARACTERISTICS @ 25°C
JEDEC		NOMINAL		ZENER		MAXIMUM			MAXIMUM			MAXIMUM
TYPE			ZENER	TEST			ZENER		REVERSE CURRENT			ZENER
NUMBER	VOLTAGE		CURRENT IMPEDANCE						I			R	@ V R			CURRENT
			V Z @ 1	ZT			1 ZT		(NOTE 3)							1
(NOTE 1)		(NOTE 2)					Z		ZT @ 1							ZM
										ZT
			VOLTS		mA				OHMS			A		VOLTS		mA
1N4370A			2.4		20				30		100			1.0	155
1N4371A			2.7		20				30		60			1.0	140				FIGURE 1
1N4372A			3.0		20				29		30			1.0	125
1N746A			3.3		20				28		5			1.0	120
1N747A			3.6		20				24		3			1.0	110
1N748A			3.9		20				23		2			1.0	100			DESIGN	DATA
1N749A			4.3		20				22		2			1.0	90
1N750A			4.7		20				19		5			1.5	85
1N751A			5.1		20				17		5			2.0	75			CASE:	Hermetically sealed glass
1N752A			5.6		20				11		5			2.5	70
																		case. DO – 35 outline.
1N753A			6.2		20				7		5			3.5	65
1N754A			6.8		20				5		2			4.0	60			LEAD MATERIAL:		Copper clad steel.
1N755A			7.5		20				6		2			5.0	55
1N756A			8.2		20				8		1			6.0	50			LEAD FINISH:		Tin / Lead
1N757A			9.1		20				10		1			7.0	45
																		THERMAL RESISTANCE: (		R					):
1N758A			10.0		20				17		1			8.0	40							O		JEC
1N759A			12.0		20				30		1			9.0	35			250 ˚C/W maximum at L = .375 inch
																		THERMAL IMPEDANCE: (		Z	O		JX ):		35
NOTE 1	Zener voltage tolerance on "A" suffix is5%+. No Suffix denotes +															10% tolerance,		˚C/W maximum
	"C" suffix denotes				+2% tollerance and "D" suffix denotes +1% tolerance.													POLARITY:	Diode to be operated with
NOTE 2	Zener voltage is measured with the device junction in thermal equilibrium at an ambient																	the banded (cathode) end positive.
	temperature of 25°C + 3°C.																	MOUNTING POSITION:		Any.
NOTE 3
	Zener impedance is derived by superimposing on 1											ZT A 60Hz rms a.c. current equal
	to 10% of 1			ZT

22 COREY	STREET, MELROSE, MASSACHUSETTS	02176
PHONE (781)	665-1071	FAX [phone]
WEBSITE: http://www.cdi-diodes.com		E-mail: [e-mail]