CDIDI 1N4915, 1N4914A, 1N4914, 1N4913A, 1N4913 Datasheet

•	12.8 VOLT NOMINAL ZENER VOLTAGE +		5%	1N4896
• TEMPERATURE COMPENSATED ZENER REFERENCE DIODES				thru
•	LOW NOISE			1N4915A

•METALLURGICALLY BONDED

•DOUBLE PLUG CONSTRUCTION

MAXIMUM RATINGS

Operating Temperature: -65°C to +175°C

Storage Temperature: -65°C to +175°C

DC Power Dissipation: 500mW @ +50°C

Power Derating: 4 mW / °C above +50°C

REVERSE LEAKAGE CURRENT
lR = 15		A @ 25°C & V		R	= 8Vdc
ELECTRICAL CHARACTERISTICS							@ 25°C, unless otherwise specified.
	JEDEC				VOLTAGE						EFFECTIVE		MAXIMUM		MAXIMUM
	TYPE		TEST	TEMPERATURE		TEMPERATURE	TEMPERATURE		DYNAMIC				NOISE
	NUMBER	CURRENT	STABILITY			RANGE		COEFFICIENT		IMPEDANCE			DENSITY
			l ZT			∆ V ZT									Z ZT		N D
			(Note 3)			(Note 2)									(Note 1)
			mA			mV			°C				%/°C		OHMS		V/ √
																		Hz
	1N4896		0.5			96	+25		to +100				0.01		400	0.8
	1N4896A		0.5			198		-55 to +100					0.01		400	0.8
	1N4897		0.5			48		+25 to +100					0.005		400	0.8
	1N4897A		0.5			99		-55 to +100					0.005		400	0.8
	1N4898		0.5			19	+25		to +100				0.002		400	0.8
	1N4898A		0.5			40		-55 to +100					0.002		400	0.8
	1N4899		0.5			10	+25		to +100				0.001		400	0.8
	1N4899A		0.5			20		-55 to +100					0.001		400	0.8
	1N4900		1.0			96	+25		to +100				0.01		200	0.4
	1N4900A		1.0			198		-55 to +100					0.01	200		0.4
	1N4901		1.0			48		+25 to +100					0.005	200		0.4
	1N4901A		1.0			99		-55 to +100					0.005	200		0.4
	1N4902		1.0			19	+25		to +100				0.002	200		0.4							FIGURE 1
	1N4902A		1.0			40		-55 to +100					0.002	200		0.4
	1N4903		1.0			10	+25		to +100				0.001	200		0.4
	1N4903A		1.0			20		-55 to +100					0.001	200		0.4
	1N4904		2.0			96	+25		to +100				0.01	100		0.25
	1N4904A		2.0			198		-55 to +100					0.01	100		0.25
	1N4905		2.0			48		+25 to +100					0.005	100		0.25
	1N4905A		2.0			99		-55 to +100					0.005	100		0.25
	1N4906		2.0			19	+25		to +100				0.002	100		0.25					DESIGN	DATA
	1N4906A		2.0			40		-55 to +100					0.002	100		0.25
	1N4907		2.0			10	+25		to +100				0.001	100		0.25
	1N4907A		2.0			20		-55 to +100					0.001	100		0.25
	1N4908		4.0			96		+25 to +100					0.01	50		0.22					CASE:	Hermetically sealed glass
	1N4908A		4.0			198		-55 to +100					0.01	50		0.22					case. DO – 35 outline.
	1N4909		4.0			48		+25 to +100					0.005	50		0.22
	1N4909A		4.0			99		-55 to +100					0.005	50		0.22
	1N4910		4.0			19		+25 to +100					0.002	50		0.22					LEAD MATERIAL:		Copper clad steel.
	1N4910A		4.0			40		-55 to +100					0.002	50		0.22
	1N4911		4.0			10		+25 to +100					0.001	50		0.22					LEAD FINISH:		Tin / Lead
	1N4911A		4.0			20		-55 to +100					0.001	50		0.22
	1N4912		7.5			96	+25		to +100				0.01	25		0.20					POLARITY:		Diode to be operated with
	1N4912A		7.5			198		-55 to +100					0.01	25		0.20
	1N4913		7.5			48		+25 to +100					0.005	25		0.20					the banded (cathode) end positive.
	1N4913A		7.5			99		-55 to +100					0.005	25		0.20
	1N4914		7.5			19	+25		to +100				0.002	25		0.20					MOUNTING	POSITION:	Any.
	1N4914A		7.5			40		-55 to +100					0.002	25		0.20
	1N4915		7.5			10	+25		to +100				0.001	25		0.20
	1N4915A		7.5			20		-55 to +100					0.001	25		0.20
	NOTE 1		Zener impedance is derived by superimposing on l ZT A 60Hz rms a.c. current equal
			to 10% of l ZT .
	NOTE 2		The maximum allowable change observed over the entire temperature range,
			per JEDEC standard No.5.
	NOTE 3		Zener voltage range equals 12.8 volts +									5%.

22 COREY	STREET, MELROSE, MASSACHUSETTS	02176
PHONE (781)	665-1071	FAX [phone]
WEBSITE: http://www.cdi-diodes.com		E-mail: [e-mail]