Canon imageCLASS MF4570dw, MF4570 Settings Manual

Wireless LAN Setting Guide

XXXXXX

Setting the

XXXXXXXXX

wireless LAN

Troubleshooting

？

P. 2 -1P. 1 -1

Starter Guide

For procedures other
than printer installation
and wireless LAN setup,
please refer to the
[Starter Guide].

Read this guide before setting up the wireless LAN

This guide describes the wireless LAN setup procedure and
problems encountered during the configuration.
After you finish reading this guide, store it in a safe place for
future reference.

Setting the wireless LAN

Step1 Checking Before the Setup

The setup of the computer and wireless LAN/access point should be completed.

If they are not set up, you will not be able to use the machine on the wireless LAN network even if you perform the following steps.

For more information, see the instruction manual for the network device you are using, or contact the networking device manufacturer.

Required Environment

Wireless LAN router

or

access point

Internet

Once you have checked the connection settings, proceed to “Step2 Switching the Connection Method to Wireless LAN”

on the next page.

Precautions when connecting to a wireless LAN

• The structure of your computer or networked device, the existence of router functions, setting methods and security settings vary depending on your

environment.

• You can connect the machine to wireless LANs or wired LANs, but you cannot use both at the same time. When using a wireless LAN connection, do not

connect a LAN cable to the machine. This may cause the machine to malfunction.

• If using the machine in your office, consult with your network administrator.

1-1

Setting the wireless LAN

Step2

When the check described on the previous page is completed, switch the connection method to wireless LAN using this
machine.

1. Press [ ] (Menu).

2. Press [ ] or [ ] to select, and press [OK].

Menu
Network Settings
Preferences
Timer Settings
Common Settings

The next screen is displayed for approximately 5
seconds.
It is not necessary to turn OFF/ON the main
power of the machine here. It will be done on
Step

5.

Switching the Connection Method to Wireless LAN

4. Press [ ] or [ ] to select, and press [OK].

Select LAN
Wired LAN

Wireless LAN

5. After the next screen disappears, turn OFF/ON the

machine.

Turn main power OFF
and ON to enable
Wired/Wireless LAN
selection.

Settings effective
after power is
turned OFF and ON.

3. Press [ ] or [ ] to select, and press [OK].

Network Settings
Select Wired/Wireles
Wireless LAN Settin...
TCP/IP Settings
SNMP Settings

It is necessary to turn OFF/ON the machine for the
settings to take effec

OFF

When the connection method has been changed,

proceed to “Step3 Selecting a Method for Setting the

Wireless LAN” on the next page.

t.

Wait for 10 seconds at least

ON

ON

OFF

1-2

Setting the wireless LAN

Step3

Two methods are provided for connecting to the wireless LAN or access point, connecting using WPS (Wi-Fi Protected
Setup) function or connecting manually.

Is there a WPS button?

• For checking whether it supports the WPS, find the descriptions such as “...

supports WPS...” or shown on the wireless LAN router/access point or its

package.

• For further information, contact the manufacturer of the wireless LAN router/

access point.

Selecting a Method for Setting the Wireless LAN

No

Proceed to “Step4-B Setting the Access

Point Manually and Connecting,” on

P.1-6.

YES

Proceed to “Step4-A Setting the Machine Using the

WPS (Push Button Mode),” on P.1-4.

Refer to the following for “WPS PIN Code Mode” or manual setting such as security:

Proceed to e-manual’s “Network Settings” → ”Basic Network Settings” → “Connecting to Wireless LAN”

1-3

Setting the wireless LAN

Step4-A

Follow this procedure only if you selected Step4-A “Setting the Machine Using the WPS (Push Button Mode)” on the
previous page.

1. Make sure the procedure “Step2 Switching the

Connection Method to Wireless LAN” (P.1-2) is
completed.

2. Press [ ] (Menu).

3. Press [ ] or [ ] to select, and press [OK].

Menu
Network Settings
Preferences
Timer Settings
Common Settings

Setting the Machine Using the WPS (Push Button Mode)

6. Press [ ] or [ ] to select, and press [OK].

Wireless LAN Settings

WPS Push Button Mode

WPS PIN Code Mode
SSID Settings
Wireless LAN Informa...

7. Press [ ] to select, and press [OK].

Do you want to
connect with new
settings?

NoYes

The next screen is displayed for approximately
5 seconds.
You do not need to turn the machine OFF and
ON at this stage.

Settings effective
after power is
turned OFF and ON.

4. Press [ ] or [ ] to select, and press [OK].

Network Settings
Select Wired/Wirele...
Wireless LAN Setting
TCP/IP Settings
SNMP Settings

5. Press [OK].

See Wireless LAN
Setting Guide to
perform settings.

8. Within 2 minutes, press and hold the WPS button

on the wireless LAN router or access point for
approximately 5 seconds.

Searching...
Press the access
point WPS button.
Cancel: Press Stop

Connecting...
Cancel: Press Stop

If “Cannot find access point” is displayed.

Press [OK] to close the screen and resume from

Step 6.



1-4

OK