Canon iPF760 series, iPF750 series Service Manual

Service Manual

iPF760/750 series

Jul 25 2012

Application

This manual has been issued by Canon Inc. for qualified persons to learn technical theory, insta llati on, ma intenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality.

Corrections

This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

Trademarks

The product names and company names used in this manual are the registered trademarks of the individual companies.

Copyright

This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or translated into another language, in whole or in part, without the written consent of Canon Inc.

Printed in Japan

Caution

Use of this manual should be strictly supervised to avoid disclosure of confidential information.

Symbols Used

This documentation uses the following symbols to indicate special information:

Symbol Description

Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.

Indicates an item requiring care to avoid electric shocks.

Indicates an item requiring care to avoid combustion (fire).

Indicates an item prohibiting disassembly to avoid electric shocks or problems.

Indicates an item requiring disconnection of the power plug from the electric outlet.

Indicates an item intended to provide notes assisting the understanding of the topic in question.

Memo

Introduction

REF.

Indicates an item of reference assisting the understanding of the topic in question.

Provides a description of a service mode.

Provides a description of the nature of an error indication.

Introduction

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation.

In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the direction of the electric signal. The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit door, which results in supplying the machine with power.

2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".(The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on when '0'. In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the fi eld. Ther efore, the operations of the microprocessors used in the machines are not discussed: they are explained in terms of fro m sensors to the input of the DC controller PCB and from the output of the DC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and major changes will be communicated in the form of Service Information bulletins. All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service Information bulletins and be able to identify and isolate faults in the machine."

Contents

Chapter 1 PRODUCT DESCRIPTION

1.1 Product Overview .......................................................................................................................................1- 1

1.1.1 Product Overview................................................................................................... ... ..............................................1- 1

1.2 Features .....................................................................................................................................................1- 2

1.2.1 Features ..................................................................................................................................................................1- 2

1.2.2 Features ..................................................................................................................................................................1- 2

1.2.3 Features ..................................................................................................................................................................1- 2

1.2.4 Features ..................................................................................................................................................................1- 2

1.2.5 Printhead.................................................................................................................................................................1- 3

1.2.6 Ink Tank.......................................................................................................................... ... ......................................1- 3

1.2.7 Cutter ........................................................................................................................................................ ...............1- 3

1.2.8 Roll Holder...............................................................................................................................................................1- 3

1.2.9 Stand (ST-33)............................................................ ... ... ........................................................................................1- 5

1.2.10 Stand (ST-34)................................................................................ ..................................... ...................................1- 7

1.2.11 Hard Disk Drive............................................................................................ ... .....................................................1- 10

1.2.12 Consumables.......................................................................................................................................................1- 10

1.3 Product Specifications..............................................................................................................................1- 11

1.3.1 Product Specifications...........................................................................................................................................1- 11

1.3.2 Product Specifications...........................................................................................................................................1- 12

1.3.3 Product Specifications...........................................................................................................................................1- 14

1.3.4 Product Specifications...........................................................................................................................................1- 16

1.4 Detailed Specifications .............................................................................................................................1- 17

1.4.1 Interface Specifications .........................................................................................................................................1- 17

1.5 Names and Functions of Components .....................................................................................................1- 19

1.5.1 Front......................................................................................................................................................................1- 19

1.5.2 Side .......................................................................................................................................................................1- 20

1.5.3 Top Cover (Inside).................................................................................................................................................1- 21

1.5.4 Roll Unit Cover (Inside) .........................................................................................................................................1- 22

1.5.5 Carriage.................................................................................................................................................................1- 22

1.5.6 Ink Tank Cover (Inside).........................................................................................................................................1- 23

1.5.7 Stand (ST-33)............................................................ ... ... ......................................................................................1- 24

1.5.8 Stand (ST-34)............................................................ ... ... ......................................................................................1- 25

1.6 Basic Operation........................................................................................................................................1- 26

1.6.1 Operation Panel.....................................................................................................................................................1- 26

1.6.2 Display...................................................................................................................................................................1- 27

1.6.3 Menu......................................................................................................................................................................1- 28

1.6.4 Menu......................................................................................................................................................................1- 46

1.7 Safety and Precautions ............................................................................................................................1- 64

1.7.1 Safety Precautions ................................................................................................................................................1- 64

1.7.1.1 Moving Parts..........................................................................................................................................................................1- 64

1.7.1.2 Adhesion of Ink ...................................................................................................................................................................... 1- 65

1.7.1.3 Electric Parts.......................................................................................................................................................................... 1- 66

1.7.1.4 Electric Parts.......................................................................................................................................................................... 1- 67

1.7.2 Other Precautions..................................................................................................................................................1- 68

1.7.2.1 Printhead................................................................................................................................................................................ 1- 68

1.7.2.2 Ink Tank ................................................................................................................................................................................. 1- 69

1.7.2.3 Handling the Printer ............................................................................................................................................................... 1- 69

1.7.3 Precautions When Servicing Printer......................................................................................................................1- 71

1.7.3.1 Notes on the Data Stored in the Printer.................................................................................................................................1- 71

1.7.3.2 Confirming the Firmware Version .......................................................................................................................................... 1- 71

1.7.3.3 Precautions against Static Electricity.....................................................................................................................................1- 71

Contents

1.7.3.4 Precautions for Disassembly/Reassembly............................................................................................................................. 1- 71

1.7.3.5 Self-diagnostic Feature..........................................................................................................................................................1- 71

1.7.3.6 Disposing of the Lithium Battery ............................................................................................................................................ 1- 72

Chapter 2 TECHNICAL REFERENCE

2.1 Basic Operation Outline .............................................................................................................................2- 1

2.1.1 Printer Diagram........................................................................................................................................................2- 1

2.1.2 Printer Diagram........................................................................................................................................................2- 2

2.1.3 Print Signal Sequence .............................................................................................................................................2- 3

2.1.4 Print Driving .............................................................................................................................................................2- 4

2.2 Firmware ....................................................................................................................................................2- 6

2.2.1 Operation Sequence at Power-on............................................................................................................... .............2- 6

2.2.2 Operation Sequence at Power-off............................................................................................................................2- 7

2.2.3 Print Control.............................................................................................................................................................2- 8

2.2.4 Print Position Adjustment Function........................................................................................................................2- 14

2.2.5 Head Management ................................................................................................................................................2- 14

2.2.6 Printhead Overheating Protection Control .............................................................................................................2- 14

2.2.7 Pause between Pages...........................................................................................................................................2- 14

2.2.8 White Raster Skip..................................................................................................................................................2- 14

2.2.9 Sleep Mode............................................................................................................................................................2- 14

2.2.10 Hard Disk Drive............................................ ... .....................................................................................................2- 15

2.3 Printer Mechanical System.. .... ... ... ... .... ... ... ... .... ... ... ... ... .... ... .......................................... ... ... ....................2- 16

2.3.1 Outline....................................................................................................................................................................2- 16

2.3.1.1 Outline.................................................................................................................................................................................... 2- 16

2.3.2 Ink Passage...........................................................................................................................................................2- 17

2.3.2.1 Ink Passage ........................................................................................................................................................................... 2- 17

2.3.2.2 Ink Tank Unit.......................................................................................................................................................................... 2- 18

2.3.2.3 Carriage Unit..........................................................................................................................................................................2- 20

2.3.2.4 Printhead................................................................................................................................................................................ 2- 24

2.3.2.5 Purge Unit..............................................................................................................................................................................2- 25

2.3.2.6 Maintenance Cartridge........................................................................................................................................................... 2- 30

2.3.2.7 Air Flow..................................................................................................................................................................................2- 31

2.3.3 Paper Path.............................................................................................................................................................2- 33

2.3.3.1 Outline.................................................................................................................................................................................... 2- 33

2.3.3.2 Paper Path.............................................................................................................................................................................2- 34

2.3.3.3 Cutter Unit..............................................................................................................................................................................2- 36

2.4 Printer Electrical System ............................... .... ... ... ... ... ....................................... ... .... ... ... .......................2- 37

2.4.1 Outline....................................................................................................................................................................2- 37

2.4.1.1 Overview................................................................................................................................................................................2- 37

2.4.1.2 Overview................................................................................................................................................................................2- 39

2.4.2 Main Controller.......................................................................................................................................................2- 41

2.4.2.1 Main controller PCB components .......................................................................................................................................... 2- 41

2.4.2.2 Main controller PCB components .......................................................................................................................................... 2- 42

2.4.2.3 HDD expansion PCB components.........................................................................................................................................2- 43

2.4.3 Carriage Relay PCB.................................. .. ...........................................................................................................2- 44

2.4.3.1 Carriage PCB components .................................................................................................................................................... 2- 44

2.4.4 Maintenance Cartridge Relay PCB........................................................................................................................2- 44

2.4.4.1 Maintenance cartridge relay PCB components...................................................................................................................... 2- 44

2.4.5 Power Supply............................................................................................................ ... ..........................................2- 45

2.4.5.1 Power supply block diagram..................................................................................................................................................2- 45

2.5 Detection Functions with Sensors..................................... ... ... ... .... ... ... ... .... ... ..........................................2- 46

2.5.1 Covers....................................................................................................................................................................2- 46

2.5.2 Ink passage system...............................................................................................................................................2- 47

2.5.3 Carriage system.....................................................................................................................................................2- 50

2.5.4 Paper path system.................................................................................................................................................2- 52

2.5.5 Others....................................................................................................................................................................2- 54

Contents

Chapter 3 INSTALLATION

3.1 Transporting the Printer..............................................................................................................................3- 1

3.1.1 Transporting the Printer........................................................................................................... ................................3- 1

3.1.1.1 Transporting the Printer ........................................................................................................................................................... 3- 1

3.1.2 Reinstalling the Printer ............................................................................................................................................3- 3

3.1.2.1 Reinstalling the Printer............................................................................................................................................................. 3- 3

Chapter 4 DISASSEMBLY/REASSEMBLY

4.1 Service Parts ..............................................................................................................................................4- 1

4.1.1 Service Parts...................... ... ............................................... ... ................................................................................4- 1

4.2 Disassembly/Reassembly...........................................................................................................................4- 2

4.2.1 Disassembly/Reassembly .......................................................................................................................................4- 2

4.3 Points to Note on Disassembly and Reassembly.......................................................................................4- 2

4.3.1 Note: Items that should never be disassembled......................................................................................................4- 2

4.3.2 Moving the carriage manually................................................................................................................................. .4- 2

4.3.3 Units requiring draining of ink..................................................................................................................................4- 3

4.3.4 External Covers................................................................................................................................................... ....4- 4

4.3.5 Drive Unit.................................... ................................................... .. ......................................................................4- 13

4.3.6 Cutter .....................................................................................................................................................................4- 16

4.3.7 Carriage Unit ............................................................................................................. .. ..........................................4- 18

4.3.8 Purge Unit..............................................................................................................................................................4- 25

4.3.9 Purge Unit..............................................................................................................................................................4- 27

4.3.10 Ink Tank Unit........................................................................................................................................................4- 32

4.3.11 Ink Tube Unit .......................................................................................................................................................4- 35

4.3.12 Waste Ink Collection Unit.....................................................................................................................................4- 39

4.3.13 Multi Sensor.........................................................................................................................................................4- 44

4.3.14 Linear Encoder ............................................................................................................. ... ....................................4- 45

4.3.15 Head Management Sensor..................................................................................................................................4- 50

4.3.16 PCBs....................................................................................................................................................................4- 51

4.3.17 Opening the Cap/Moving the Wiper Unit.............................................................................................................4- 52

4.3.18 Opening/Closing the Ink Supply Valve/Subtank Air Passage Valve....................................................................4- 54

4.3.19 Draining the ink....................................................................................................................................................4- 55

4.4 Applying the Grease.................................................................................................................................4- 56

4.4.1 Applying the Grease..............................................................................................................................................4- 56

4.5 Adjustment and Setup Items ....................................................................................................................4- 60

4.5.1 Adjustment Item List.......................................................................................................... ....................................4- 60

4.5.2 Procedure after Replacing the Carriage Unit or Multi Sensor ...............................................................................4- 60

4.5.3 Procedure after Replacing the Feed Roller or Feed Roller Encoder................................. ....................................4- 60

4.5.4 Procedure after Replacing the Head Management Sensor...................................................................................4- 60

Chapter 5 MAINTENANCE

5.1 Periodic Replacement Parts.......................................................................................................................5- 1

5.1.1 Periodic Replacement Parts....................................................................................................................................5- 1

5.2 Consumable Parts......................................................................................................................................5- 1

5.2.1 Consumable Parts............................................................................................................................................ ... ....5- 1

5.3 Periodic Maintenance...................................... ... ... ... .... ... ... ... .... .................................................................5- 2

5.3.1 Periodic Maintenance..............................................................................................................................................5- 2

Chapter 6 TROUBLESHOOTING

6.1 Troubleshooting..........................................................................................................................................6- 1

6.1.1 Outline.....................................................................................................................................................................6- 1

6.1.1.1 Outline of Troubleshooting.......................................................................................................................................................6- 1

6.2 Location of Connectors and Pin Arrangement............................................................................................6- 1

Contents

6.2.1 Main controller PCB.................................................................................................................................................6- 1

6.2.2 Carriage PCB....................................................... ... .................................................. ... ....................................... ... ..6- 8

6.2.3 Power supply ................................................. ... ... .................................................. ................................................6- 12

6.3 Version Up..... ... ... .... ... ... ... ... ....................................... ... .... ... ... ... ..............................................................6- 13

6.3.1 Firmware Update Tool ...........................................................................................................................................6- 13

6.4 Service Tools............................................................................................................................................6- 17

6.4.1 Tool List .............................................. ... ... .............................................................................................................6- 17

Chapter 7 SERVICE MODE

7.1 Service Mode .............................................................................................................................................7- 1

7.1.1 Service Mode Operation............................................................................................................... ...........................7- 1

7.1.2 Map of the Service Mode................................................................................................................................. ... .....7- 2

7.1.3 Details of Service Mode.................................................. ... ......................................................................................7- 9

7.1.4 e-Maintenance/imageWARE Remote....................................................................................................................7- 24

7.1.5 Viewing PRINT INF................................................................................................................................................7- 34

7.2 Special Mode............................................................................................................................................7- 49

7.2.1 Special Modes for Servicing ..................................................................................................................................7- 49

Chapter 8 ERROR CODE

8.1 Outline........................................................................................................................................................8- 1

8.1.1 Outline.................................................................................................................................................................... ..8- 1

8.2 Warning Table............................................................................................................................................8- 2

8.2.1 Warnings..................................................................................................................................................................8- 2

8.3 Error Table .................................................................................................................................................8- 5

8.3.1 Errors.......................................................................................................................................................................8- 5

8.4 Sevice Call Table ..................................................................................................................................... 8- 16

8.4.1 Service Call Errors....................................................... ..........................................................................................8- 16

Chapter 1 PRODUCT DESCRIPTION

Contents

1.1 Product Overview .......................................................................................................................................................... 1-1

1.1.1 Product Overview ........................................................................................................................................................................ 1-1

1.2 Features..........................................................................................................................................................................1-2

1.2.1 Features........................................................................................................................................................................................ 1-2

1.2.2 Features........................................................................................................................................................................................ 1-2

1.2.3 Features........................................................................................................................................................................................ 1-2

1.2.4 Features........................................................................................................................................................................................ 1-2

1.2.5 Printhead ...................................................................................................................................................................................... 1-3

1.2.6 Ink Tank....................................................................................................................................................................................... 1-3

1.2.7 Cutter............................................................................................................................................................................................ 1-3

1.2.8 Roll Holder................................................................................................................................................................................... 1-3

1.2.9 Stand (ST-33)............................................................................................................................................................................... 1-5

1.2.10 Stand (ST-34)............................................................................................................................................................................. 1-7

1.2.11 Hard Disk Drive....................................................................................................................................................................... 1-10

1.2.12 Consumables............................................................................................................................................................................ 1-10

1.3 Product Specifications..................................................................................................................................................1-11

1.3.1 Product Specifications ............................................................................................................................................................... 1-11

1.3.2 Product Specifications ............................................................................................................................................................... 1-12

1.3.3 Product Specifications ............................................................................................................................................................... 1-14

1.3.4 Product Specifications ............................................................................................................................................................... 1-16

1.4 Detailed Specifications ................................................................................................................................................1-17

1.4.1 Interface Specifications.............................................................................................................................................................. 1-17

1.5 Names and Functions of Components ......................................................................................................................... 1-19

1.5.1 Front........................................................................................................................................................................................... 1-19

1.5.2 Side ............................................................................................................................................................................................ 1-20

1.5.3 Top Cover (Inside)..................................................................................................................................................................... 1-21

1.5.4 Roll Unit Cover (Inside) ........... ............................. ............................. ............................ ........................................................... 1-22

1.5.5 Carriage...................................................................................................................................................................................... 1-22

1.5.6 Ink Tank Cover (Inside)............................................................................................................................................................. 1-23

1.5.7 Stand (ST-33)............................................................................................................................................................................. 1-24

1.5.8 Stand (ST-34)............................................................................................................................................................................. 1-25

1.6 Basic Operation............................................................................................................................................................ 1-26

1.6.1 Operation Panel.......................................................................................................................................................................... 1-26

1.6.2 Display....................................................................................................................................................................................... 1-27

1.6.3 Menu .......................................................................................................................................................................................... 1-28

1.6.4 Menu .......................................................................................................................................................................................... 1-46

1.7 Safety and Precautions.................................................................................................................................................1-64

1.7.1 Safety Precautions...................................................................................................................................................................... 1-64

1.7.1.1 Moving Parts .................................................................................................................................................................................................1-64

1.7.1.2 Adhesion of Ink.............................................................................................................................................................................................1-65

1.7.1.3 Electric Parts .................................................................................................................................................................................................1-66

1.7.1.4 Electric Parts .................................................................................................................................................................................................1-67

1.7.2 Other Precautions....................................................................................................................................................................... 1-68

1.7.2.1 Printhead .......................................................................................................................................................................................................1-68

1.7.2.2 Ink Tank ........................................................................................................................................................................................................1-69

1.7.2.3 Handling the Printer ......................................................................................................................................................................................1-69

1.7.3 Precautions When Servicing Printer .................. ....................................................... ................................................................. 1-71

1.7.3.1 Notes on the Data Stored in the Printer.........................................................................................................................................................1-71

1.7.3.2 Confirming the Firmware Version................................................................................................................................................................1-71

1.7.3.3 Precautions against Static Electricity ............................................................................................................................................................1-71

1.7.3.4 Precautions for Disassembly/Reassembly.....................................................................................................................................................1-71

Contents

1.7.3.5 Self-diagnostic Feature .................................................................................................................................................................................1-71

1.7.3.6 Disposing of the Lithium Battery ........................................ ... ...................................... ................................................................................1-72

1.1 Product Overview

Chapter 1

1.1.1 Product Overview

iPF765 / iPF760 / iPF750 / iPF755

0023-1254

This printer is capable of printing on A4- to A0-size cut sheets and its maximum print width is 36 inches. This printer is a desktop large-format printer five-colors (dye- and pigment-based colors) printer that can be used to print CAD and office documents as well as handy POP and posters.

[3] [14]

[15] [1]

[2]

[3]

[4]

[6]

[5]

[13]

[6]

[16]

[7]

[9]

[8]

[10][11][12]

F-1-1

[1] Roll media cover [9] Maintenance cartridge [2] Media loading slot [10] Cutter unit [3] Roll media temporary table [11] Cutter rail [4] Release lever [12] Paper eject slot [5] Operation panel [13] Output guide [6] Ink tank cover [14] Upper cover [7] Media alignment line [15] Width guide [8] Maintenance cartridge cover [16] Stand

1-1

Chapter 1

1.2 Features

1.2.1 Features

iPF755

- High resolutions of 2,400 x 1,200 dp i maximum , coupled with the exceptionally light- fast, water-proof and ozon e-proof fi ve-color pigment inks of Y, M, C, PBK and MBK, deliver high-quality photographic picture quality.

- Black ink suitable for the selected media type is automatically selected from two types of black ink, "black ink" for vivid and glossy printing and "matte black ink" for matte and high-quality printing.

- A 160-by-128-dot-large LCD

- One-inch wide printhead having 2,560 nozzles per color, which are as many as the those of the existing models. High-density printhead technology "FINE" that can satisfy both of beautiful and fast printing requirements of a high order is employed for accurate ejection of ultrasmall 4-pl drops of ink to the target positions. Prints with 2,400 x 1,200 dpi resolution can be made at a high speed.

- Imaging processor "L-COA" incorporated for high-speed image data processing. High-speed processing of 5-color, 12-bit large-size images and printer control for high-accuracy operation of high-density head can be performed with a single chip.

- Standard support for 10Base-T/100Base-TX/1000Base-T and USB 2.0 Hi-Speed.

- Borderless printing on and auto cutting of roll media.

- The hard disk is installed for better print job management. Functional enhancements new to this model include:

- All operations such as loading the roll media and cassette paper can be carried out at the front (top) of the printer, enhancing operability.

- The printer can be installed with its back in touch with the wall, requiring no installation space at the back of the printer.

- A subtank mounted at the ink port allows you to replace the ink tank during printing.

- The pressure of suction from the borderless printing ink catch groove changes automatically with the media size, preventing shift of media edges and staining of the backside of the media.

- A printhead having nozzles (I-shaped nozzle) with a new shape reduces ink mist, ensuring superfine printing.

- Compatibility with e-maintenance/imageWARE Remote allows centralized management of customers' printer information.

- The newly designed operation panel allows you to operate the printer intuitively.

1.2.2 Features

iPF750

0023-1255

0023-2438

- High resolutions of 2,400 x 1,200 dp i maximum , coupled with the exceptionally light- fast, water-proof and ozon e-proof fi ve-color pigment inks of Y, M, C, PBK and MBK, deliver high-quality photographic picture quality.

- Black ink suitable for the selected media type is automatically selected from two types of black ink, "black ink" for vivid and glossy printing and "matte black ink" for matte and high-quality printing.

- A 160-by-128-dot-large LCD

- One-inch wide printhead having 2,560 nozzles per color, which are as many as the those of the existing models. High-density printhead technology "FINE" that can satisfy both of beautiful and fast printing requirements of a high order is employed for accurate ejection of ultrasmall 4-pl drops of ink to the target positions. Prints with 2,400 x 1,200 dpi resolution can be made at a high speed.

- Imaging processor "L-COA" incorporated for high-speed image data processing. High-speed processing of 5-color, 12-bit large-size images and printer control for high-accuracy operation of high-density head can be performed with a single chip.

- Standard support for 10Base-T/100Base-TX/1000Base-T and USB 2.0 Hi-Speed.

- Borderless printing on and auto cutting of roll media. Functional enhancements new to this model include:

- All operations such as loading the roll media and cassette paper can be carried out at the front (top) of the printer, enhancing operability.

- The printer can be installed with its back in touch with the wall, requiring no installation space at the back of the printer.

- A subtank mounted at the ink port allows you to replace the ink tank during printing.

- The pressure of suction from the borderless printing ink catch groove changes automatically with the media size, preventing shift of media edges and staining of the backside of the media.

- A printhead having nozzles (I-shaped nozzle) with a new shape reduces ink mist, ensuring superfine printing.

- Compatibility with e-maintenance/imageWARE Remote allows centralized management of customers' printer information.

- The newly designed operation panel allows you to operate the printer intuitively.

1.2.3 Features

iPF765

- High resolutions of 2,400 x 1,200 dp i maximum , coupled with the exceptionally light- fast, water-proof and ozon e-proof fi ve-color pigment inks of Y, M, C, PBK and MBK, deliver high-quality photographic picture quality.

- Black ink suitable for the selected media type is automatically selected from two types of black ink, "black ink" for vivid and glossy printing and "matte black ink" for matte and high-quality printing.

- A 160-by-128-dot-large LCD

- One-inch wide printhead having 2,560 nozzles per color, which are as many as the those of the existing models. High-density printhead technology "FINE" that can satisfy both of beautiful and fast printing requirements of a high order is employed for accurate ejection of ultrasmall 4-pl drops of ink to the target positions. Prints with 2,400 x 1,200 dpi resolution can be made at a high speed.

- Imaging processor "L-COA" incorporated for high-speed image data processing. High-speed processing of 5-color, 12-bit large-size images and printer control for high-accuracy operation of high-density head can be performed with a single chip.

- Standard support for 10Base-T/100Base-TX/1000Base-T and USB 2.0 Hi-Speed.

- Borderless printing on and auto cutting of roll media.

- The hard disk is installed for better print job management.

- All operations such as loading the roll media and cassette paper can be carried out at the front (top) of the printer.

- The printer can be installed with its back in touch with the wall, requiring no installation space at the back of the printer.

- A subtank mounted at the ink port allows you to replace the ink tank during printing.

- The pressure of suction from the borderless printing ink catch groove changes automatically with the media size, preventing shift of media edges and staining of the backside of the media.

- A printhead having nozzles (I-shaped nozzle) with a new shape reduces ink mist, ensuring superfine printing.

- Compatibility with e-maintenance/imageWARE Remote allows centralized management of customers' printer information.

0028-0090

- The newly designed operation panel allows you to operate the printer intuitively. Functional enhancements new to this model include:

- The processing ability of the printed data will enhance by increase of hard disk drive and memory capacity and improvement of throughput.

1.2.4 Features

iPF760

0028-0098

- High resolutions of 2,400 x 1,200 dp i maximum , coupled with the exceptionally light- fast, water-proof and ozon e-proof fi ve-color pigment inks of Y, M, C, PBK

1-2

Chapter 1

and MBK, deliver high-quality photographic picture quality.

- Black ink suitable for the selected media type is automatically selected from two types of black ink, "black ink" for vivid and glossy printing and "matte black ink" for matte and high-quality printing.

- A 160-by-128-dot-large LCD

- One-inch wide printhead having 2,560 nozzles per color, which are as many as the those of the existing models. High-density printhead technology "FINE" that can satisfy both of beautiful and fast printing requirements of a high order is employed for accurate ejection of ultrasmall 4-pl drops of ink to the target positions. Prints with 2,400 x 1,200 dpi resolution can be made at a high speed.

- Imaging processor "L-COA" incorporated for high-speed image data processing. High-speed processing of 5-color, 12-bit large-size images and printer control for high-accuracy operation of high-density head can be performed with a single chip.

- Standard support for 10Base-T/100Base-TX/1000Base-T and USB 2.0 Hi-Speed.

- Borderless printing on and auto cutting of roll media.

- All operations such as loading the roll media and cassette paper can be carried out at the front (top) of the printer.

- The printer can be installed with its back in touch with the wall, requiring no installation space at the back of the printer.

- A subtank mounted at the ink port allows you to replace the ink tank during printing.

- The pressure of suction from the borderless printing ink catch groove changes automatically with the media size, preventing shift of media edges and stainin g of the backside of the media.

- A printhead having nozzles (I-shaped nozzle) with a new shape reduces ink mist, ensuring superfine printing.

- Compatibility with e-maintenance/imageWARE Remote allows centralized management of customers' printer information.

- The newly designed operation panel allows you to operate the printer intuitively. Functional enhancements new to this model include:

- The processing ability of the printed data will enhance by improvement of throughput.

1.2.5 Printhead

iPF765 / iPF760 / iPF750 / iPF755 The printhead that mounts on the carriage is an integrated six-color disposable printhead.

It has 5,120 nozzles for MBK and 2,560 nozzles for each additional color arranged in a staggered pattern.

0013-2741

If print quality remains unimproved even after a specified cleaning operation, replace the printhead.

F-1-2

1.2.6 Ink Tank

iPF765 / iPF760 / iPF750 / iPF755 The ink tank is disposable.

There are four dye-based ink colors (black, cyan, magenta, and yellow) and one pigment-based ink color (matte black). This printer features a mechanism by which only the correct color ink tank will fit in the given slot. When the message that ink tank is empty is displayed, replace the ink tank with a new one.

F-1-3

1.2.7 Cutter

iPF765 / iPF760 / iPF750 / iPF755 The cutter attached to the cutter unit is a round cutter.

0012-6188

0023-1309

1.2.8 Roll Holder

iPF765 / iPF760 / iPF750 / iPF755

F-1-4

0023-1308

1-3

Chapter 1

The roller holder accepts paper tubes having inside diameters of both 2 and 3 inches. It is furnished with attachments for 2- and 3-inch diameter paper tubes. The roll holder clamps the paper tube of a roll not exceeding 150 mm in outside diameter from the inside.

F-1-5

[2-inch paper tube attachment]

F-1-6

[3-inch paper tube attachment R]

[3-inch paper tube attachment L]

F-1-7

F-1-8

1-4

Chapter 1

1.2.9 Stand (ST-33)

iPF750 / iPF755

0023-1260

The stand [1] is equipped with casters so that the printer can be easily moved. The output stacker [2] included with stand can use by the tw o ways of the regula r position or extended position.

[1]

[2]

F-1-9

MEMO:

- When delivering the printing to the output stacker: Use the position [A].

- When not using the output stacker or moving the printer: Use the position [B]. When moving the printer, raise the auxiliary rod to the position of extended position. The output stacker may touch the floor and be soiled or damaged.

[Regular position]

[A]

[B]

F-1-10

F-1-11

1-5

Chapter 1

[Extended position]

F-1-12

- Changing from the regular position to extended position.

1) Raise the auxiliary rod [1] to the position [A] of the illustration to change to the extended position.

[A]

[1]

F-1-13

2) Pull out the switching stopper [1] when using roll paper that is A1 size or has a width of 24 inches.

[1]

F-1-14

1-6

Chapter 1

1.2.10 Stand (ST-34)

iPF765 / iPF760 / iPF750 / iPF755

0027-2228

The stand [1] is equipped with casters so that the printer can be easily moved. The output stacker [2] included with stand can use by the three ways of the regula r position or two extended positions.

[1]

[2]

F-1-15

MEMO:

- When delivering the printing to the output stacker: Use the position [A].

- When not using the output stacker or moving the printer: Use the position [B]. When moving the printer, raise the auxiliary rod to the position of extended position. The output stacker may touch the floor and be soiled or damaged.

[Regular position]

[A]

[B]

F-1-16

F-1-17

1-7

Chapter 1

[Extended position A]

F-1-18

- Changing from the regular position to extended position A.

1) Raise the auxiliary rod [1] to the position [A] of the illustration to change to the extended position A.

[A]

[1]

F-1-19

2) Pull out the switching stopper [1] when using roll paper that is A1 size or has a width of 24 inches.

[1]

F-1-20

[Extended position B]

1-8

F-1-21

- Changing from the regular position to extended position B.

1) Grasp the output stacker handle [1] to set the guide as shown in the following illustration.

[1]

F-1-22

2) Open the output stacker ejection guides [1] toward the front.

[1]

Chapter 1

F-1-23

- Changing from the extended position B to regular position.

1) Close the output stacker ejection guides [1] and pull the output stacker release lever [2] forward to release the lock, and then grasp the output stacker handle [3] to return the guide.

[2]

[1]

[3]

F-1-24

1-9

Chapter 1

1.2.11 Hard Disk Drive

iPF765 / iPF755

0017-8472

Each print job received from the host computer is saved to the hard disk drive(serial ATA connection) attached to the printer, so the printer can print the job repeatedly as needed, without having to wait for its retransmission from the host computer.

Saving print jobs will offer the following benefits:

- Eased computer workload A print job may be automatically preserved to the hard disk when printing or may be preserved to the hard disk without printing. A print job preserve d can be printed in as many copies as needed without having to use the host computer.

- Reprinting after error occurrence If the printer encounters errors, such as paper out, while printing a print job, it can resume the print operation as soon as the errors are cleared, without needing its retransmission from the host computer.

- Higher print work eff iciency Print jobs can be printed selectively or in a specified number of copies without using a host computer. Multiple print jobs can be printed batched. Unattended print operations in the nighttime are also possible.

1.2.12 Consumables

iPF765 / iPF760 / iPF750 / iPF755

Printhead

The consumable printhead is the same as that supplied with the printer.

0023-1261

F-1-25

Ink Tanks

The consumable ink tanks are available in five colors (matte black, black, cyan, magenta and yellow). They are the same as those supplied with the printer. The ink tank that can be used with this printer is labeled "J".

F-1-26

MEMO:

You can also use ink tanks other than magenta ink tank that are simply labeled "A".

Maintenance Cartridge

The consumable maintenance cartridge is the same as that supplied with the printer.

1-10

F-1-27

1.3 Product Specifications

Chapter 1

1.3.1 Product Specifications

iPF755

Type Bubble jet large-sized paper printer (stand model) Feeding system Roll media: manual feed from top

Feeding capacity - Roll media: 1 roll madia (Outer diameter of roll: 150 mm or less/Inner

Delivery method Forward delivery, face up Sheet delivery capability Stacking to the output stacker of the stand

Cutter Automatic cross-cutter (round blade) Type of media Roll Media:

Supported thickness 0.07mm to 0.8mm Media size (Roll media) Width: 254.0mm (10") to 914.4mm (36")

Media size (Cut sheet) Width: 203.2mm (8") to 917.0mm

Printable area (Roll media) Internal area, excluding a 3-mm top, bottom and left and right margins.

Printable area (Cut sheet) Internal area, excluding a 3-mm top margin, a 23-mm bottom margin and

Printing recommendation area (Roll media)

Printing recommendation area (Cut sheet)

Memory 256MB

Hard disk drive 80GB or 160GB (2.5inch, 5,400rpm) Firmware Flash ROM (update from USB or Ethernet)

Cut sheet: manual feed from top

diameter of paper tube: 2 or 3 inches)

- Cut sheet: 1 sheet

- 1 sheet: when using in the regular position

- approximate 20 sheets: when using in the extended position (However, it has the following restrictions.) when using in the extended position/extended position A: paper length A0/36"X48" or A1/24"X36" size plain paper or recycled paper when using in the extended position B: paper length A1/36"X24" or A2/ 24"X18" size plain paper or recycled paper

Plain Paper, Plain Paper (High Quality), Plain Paper (High Grade), Coated Paper, Heavyweight Coated Paper, Premium Matte Paper, Premium Glossy Paper 200, Premium Semi-Glossy Paper 200, Premium Glossy Paper 280, Premium Semi-Glossy Paper 280, Back Light Film, Economy Bond Paper, Universal Bond Paper, Matte Coated Paper 170gsm, Premium RC Photo Luster, Durable Backlit Film, High Resolution Coated Paper, Matte Coated Paper 90gsm, Glossy Photographic Paper 190gsm, Glossy Photographic Paper 240gsm, Satin Photographic Paper 240gsm, Glossy Photographic Paper 270gsm, Satin Photographic Paper 270gsm, HW Glossy Photo Paper, HW Satin Photo Paper, Commercial Proofing Paper, Standard Paper1569B 80g, Standard Paper1570B 90g, Matt Coated Paper 9171, Matt Coated Paper 7215, Matt Coated Paper 140g, Opaque Paper White, Hi Res Graphic Paper, Hi Res Barrier Paper, Photo Realistic Paper 210g, Photo paper Pearl 260g, Glossy Proofing Paper 195g, Semiglossy Proofing Paper 195g, Semiglossy Proofing Paper 255g

Cut Paper: Plain Paper, Plain Paper (High Quality), Plain Paper (High Grade), Coated Paper, Premiun Matte Paper, Premium Glossy Paper 280, Premium Semi-Glossy Paper 280, High Resolution Paper, Matte Photo Paper, Glossy Photo Paper GP-501, Photo Paper Plus Glossy 2, Photo Paper Pro Platium, Photo Paper Plus Semi-Gloss, Universal Bond Paper, Premium RC Photo Luster, High Resolution Coated Paper, Matt Coated Paper 7215, Matt Coated Paper 140g

Length: 203.2mm (8") to 18m (709") *1 Outer diameter of roll :150mm or less *1: The maximum amount of length may vary by the using operating system or the applications.

Length: 279.4mm (11") to 1600mm (63") *1 *1: The maximum amount of length may vary by the using operating system or the applications.

Borderless printing: 0 mm from the leading edge, trailing edge, and left and right edges. * The printable area may vary with each type of paper media used.

Width of media allowing borderless printing: 36"(914.4mm), A0(841.0mm), B1(728.0mm), 24"(609.6mm), A1(594.0mm), B2(515.0mm), 17"(431.8mm), A2(420.0mm), 14"(355.6mm), 300mm, A3(297.0mm), B4(257.0mm), 10"(254mm)

3-mm left and right margins. * The printable area may vary with each type of paper media used.

Internal area, excluding a 20-mm top margin, a 5-mm bottom margin and 5-mm left and right margins.

Internal area, excluding a 20-mm top margin, a 23-mm bottom margin and 5-mm left and right margins.

Increase of memory: none

- Printer description language GARO (Graphic Arts language with Raster Operation), HP-GL/2, HPRTL

0023-1273

1-11

Chapter 1

Interface USB2.0 Hi-Speed

Operation panel LCD (160 X 128 dots), 13 keys, 5 LEDs

Printhead/Ink Tank type Printhead and separate ink tanks Printhead PF-04

Ink tank PFI-102 MBK/BK/C/Y

Detection functions (Cover system)

Detection functions (Ink passage system)

Detection functions (Carriage system)

Detection functions (Paper path system)

Operating noise Operating: Approx. 50dB (A) or less

Operating environment Temperature: 15 to 30 degrees centigrade

Print quality guaranteed environment

Power supply 100-240 VAC (50/60 Hz) Power consumption (Maximum) During printing: Max. 140 W Power consumption In power save (sleep) mode:

Printer unit dimensions (WxDxH)

Weight Approx. 63.1 kg (with stand and without printhead and ink tank)

Network (10Base-T/100Base-TX/1000Base-T)

- Panel language English

- Message language English, German, French, Italian, Spanish, Chinese, Korean, Russianand and Japanese

Structure: Integrated six-color assembly Number of nozzles: 5,120 for MBK, 2,560 for other each color

PFI-104 M Capacity: 130 ml per color (Ink tanks supplied with the printer contain 90 ml pf each color.)

Upper cover open/closed detection: Yes Ink tank cover open/closed detection: Yes

Ink tank presence/absence detection: Yes Remaining ink level detection (dot count and electrode): Yes Maintenance cartridge presence/absence detection: Yes Used ink tank full detection: Yes Ink supply Valve open/closed detection: Yes Air passage Valve open/closed detection: Yes

Printhead presence/absence detection: Yes Carriage position detection: Yes Carriage home position detection: Yes Printhead temperature detection: Yes Printhead height detection: Yes Non-discharging nozzle detection: Yes Non-discharging nozzle backup feature: Yes Ambient temperature/humidity detection: Yes

Paper presence/absence detection: Yes Paper width detection: Yes Skew detection: Yes Paper leading edge and trailing edge detection: Yes Release lever position detection: Yes Remaining roll media detection: Yes Feed roller rotation detection: Yes Roll holder rotation detection: Yes Cutter positin detection: Yes

Standby: Approx. 35dB (A) or less

Humidity: 10% to 80%RH without dew condensation Temperature: 15 to 30 degrees centigrade

Humidity: 10% to 80%RH

100-120 VAC : 5W or less 220-240 VAC : 6W or less During standby: 1 W or less

1304mm(W) x 870mm(D) x 1062mm(H) (with ST-33 stand and opening the output stacker) 1304mm(W) x 887mm(D) x 1062mm(H) (with ST-34 stand and opening the output stacker) 1304mm(W) x 1100mm(D) x 1062mm(H) (with ST-34 stand and setting to the extended position B)

1.3.2 Product Specifications

iPF750

Type Bubble jet large-sized paper printer (stand model) Feeding system Roll media: manual feed from top

Feeding capacity - Roll media: 1 roll madia (Outer diameter of roll: 150 mm or less/Inner

Delivery method Forward delivery, face up Sheet delivery capability Stacking to the output stacker of the stand

Cutter Automatic cross-cutter (round blade)

1-12

Cut sheet: manual feed from top

diameter of paper tube: 2 or 3 inches)

- Cut sheet: 1 sheet

- 1 sheet: when using in the regular position

- approximate 20 sheets: when using in the extended position (However, it has the following restrictions.) when using in the extended position/extended position A: paper length A0/36"X48" or A1/24"X36" size plain paper or recycled paper when using in the extended position B: paper length A1/36"X24" or A2/ 24"X18" size plain paper or recycled paper

0023-2439

Chapter 1

Type of media Roll Media:

Supported thickness 0.07mm to 0.8mm Media size (Roll media) Width: 254.0mm (10") to 914.4mm (36")

Media size (Cut sheet) Width: 203.2mm (8") to 917.0mm

Printable area (Roll media) Internal area, excluding a 3-mm top, bottom and left and right margins.

Printable area (Cut sheet) Internal area, excluding a 3-mm top margin, a 23-mm bottom margin and

Printing recommendation area (Roll media)

Printing recommendation area (Cut sheet)

Memory 256MB

Firmware Flash ROM (update from USB or Ethernet)