Brother MFC-9010CN Quick Setup Guide
Quick Setup Guide
Start Here
Before you can use the machine, please read this Quick Setup Guide for the correct setup and installation.
To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/
MFC-9010CN
.
IMPORTANT
DO NOT connect the interface cable yet.
Unpack the machine and check the components
1
Product Registration
Sheet
(USA only)
User’s Guide
Accessory Order
Form
CD-ROM
(Windows
(Macintosh)
Waste Toner Box
(pre-installed)
®
)
Quick Setup Guide
Belt Unit
(pre-installed)
Drum Unit and Starter Toner Cartridge
(Black, Cyan, Magenta and Yellow)
AC Power Cord
Assemblies
WARNING
• Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep
these bags away from babies and children.
• This machine is heavy and weighs approximately 50.0 lb. (22.7 kg). To prevent injuries use at least two
people to lift the machine. Be careful not to pinch your fingers when you put the machine back down.
USA/CAN Version A
1
Note
Keep a minimum gap around the machine as shown in the illustration.
15.7 in. (400 mm)
4 in.
(100 mm)
4 in.
(100 mm)
4.7 in.
(120 mm)
Note
• The components included in the box may differ depending on your country.
• Save all packing materials and the box in case for any reason you must ship your machine.
• The interface cable is not a standard accessory. Buy the appropriate interface cable for the interface you
want to use (USB or Network).
USB cable
• Please make sure you use a USB 2.0 cable (Type A/B) that is no longer than 6 feet (2 meters).
• DO NOT connect the interface cable at this time. Connecting the interface cable is done during MFL-Pro
installation process.
• When you use a USB cable, make sure you connect it to the USB port of your computer and not to a USB
port on a keyboard or non-powered USB hub.
Network cable
Use a straight-through Category 5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet
Network.
2
Symbols used in this guide
WARNING
CAUTION
IMPORTANT
Note
User's Guide
Network User's
Guide
WARNINGs tell you what to do to prevent possible personal injury.
CAUTIONs specify procedures you must follow or avoid to prevent possible minor injuries.
IMPORTANT specifies procedures you must follow or avoid to prevent possible damage to the
machine or other objects.
Notes tell you how you should respond to a situation that may arise or give tips about how the
current operation works with other features.
Indicates reference to the User's Guide or Network User's Guide which is on the CD-ROM we
have supplied.
3
Remove the packing
material from the
2
IMPORTANT
• Save all packing material and the carton in
case you have to ship your machine.
• DO NOT plug in the AC power cord yet.
machine
a Remove the packing tape from the outside of
the machine.
b Open the top cover by lifting up on the
handle a.
c Remove the packing material from the inside of
the machine.
1
4
Install the drum unit and
Y
toner cartridge
3
assemblies
a Unpack the four drum unit and toner cartridge
assemblies and gently shake each of them
from side to side several times to distribute the
toner evenly inside the assembly.
c Slide all four of the drum unit and toner
cartridge assemblies into the machine as
shown in the illustration. Make sure that you
match the toner cartridge color to the same
color label on the machine.
b Remove the protective cover by pulling on the
tab as shown in the illustration.
Note
Do not touch the surface of the packing film. It
may contain toner powder which can stain your
skin and clothing.
C
M
K
C - Cyan Y - Yellow
M - Magenta K - Black
d Close the top cover of the machine.
IMPORTANT
To avoid print quality
problems, DO NOT touch the
surface of the drum unit.
5
Load paper in the paper
4
tray
a Pull the paper tray completely out of the
machine.
d Put paper in the tray, and make sure that the
paper is below the maximum paper mark a.
The side to be printed on must be face down.
IMPORTANT
Make sure the paper guides touch the sides of
the paper so it will feed properly.
b While pressing the green paper-guide release
lever a, slide the paper guides to fit the paper
size you are loading in the tray. Make sure that
the guides are firmly in the slots.
c Fan the stack of paper well to avoid paper jams
and misfeeds.
e Put the paper tray firmly back in the machine.
Make sure that it is completely inserted into the
machine.
f Unfold the support flap a to prevent paper
from sliding off the face-down output tray.
1
6
5
Connect the power cord
6
Choose your language (if needed)
IMPORTANT
DO NOT connect the interface cable yet.
a Make sure that the machine’s power switch is
off. Connect the AC power cord to the machine.
b Plug the AC power cord into an AC outlet. Turn
the power switch on.
a Press Menu, 1, 0.
General Setup
0.Local Language
b Press a or b to choose your language.
Press OK.
c Press Stop/Exit.
7
Set the LCD contrast
7
If you are having difficulty reading the LCD, try
changing the contrast setting.
(if needed)
a Press Menu, 1, 4.
General Setup
4.LCD Contrast
b Press a to increase the contrast.
—OR—
Press b to decrease the contrast.
Press OK.
c Press Stop/Exit.
8
Choose your connection type
8
For USB Interface Users
Windows®, go to page 10
Macintosh, go to page 14
For Wired Network
Windows®, go to page 16
Macintosh, go to page 21
Windows
®
USB
Macintosh
Windows
Wired Network
®
Macintosh
Note
For Windows Server® 2003/ 2008, see the Network User’s Guide on the CD-ROM.
9
Loading...