Bosch Rotak 34 R Instruction manual
OBJ_DOKU-36613-001.fm Page 1 Tuesday, September 24, 2013 3:07 PM
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-garden.com
F 016 L81 043 (2013.09) O / 12 XXX
Rotak
34 R | 37 R | 340 R | 370 R
en Original instructions
OBJ_BUCH-2040-001.book Page 2 Friday, September 20, 2013 10:44 AM
2 | English
strict the age of the operator. When not in use store the
English
Safety Notes
Warning! Read these instructions carefully, be familiar
with the controls and the proper use of the machine.
Please keep the instructions safe for later use!
Explanation of symbols
General hazard safety alert.
Read instruction manual.
Pay attention that bystanders are not injured
through foreign objects thrown from the machine.
Warning: Keep a safe distance from the machine
when operating.
Caution: Do not touch rotating blades. Sharp
blade(s). Beware of severing toes or fingers.
Not applicable.
Switch off and remove plug from mains before adjusting, cleaning or if the cable is entangled and
before leaving the garden product unattended for
any period. Keep the supply flexible cord away
from the cutting blades.
Wait until all machine components have completely stopped before touching them. The blades
continue to rotate after the machine is switched
off, a rotating blade can cause injury.
Do not use the machine in the rain or leave it outdoors when it is raining.
Beware electric shock hazard.
Keep supply flexible cord away from cutting
means.
Operation
Always wear gardening gloves when handling or work-
ing near the sharp blades.
Never allow children or people unfamiliar with these in-
structions to use the machine. Local regulations may re-
machine out of reach of children.
This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the machine by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the machine.
Never mow while people, especially children or pets, are
nearby.
The operator or user is responsible for accidents or dam-
age that occur to people or property.
Do not operate the machine when barefoot or wearing
open sandals, always wear substantial footwear and long
trousers.
Thoroughly inspect the area where the machine is to be
used and remove all stones, sticks, wires, bones and other
foreign objects.
Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades and bolts to
preserve balance.
Mow only in daylight or in good artificial light.
Avoid operating the machine in wet grass, where feasible.
Walk, never run.
Never operate the appliance with defective guards or
shields, or without safety devices, for example deflectors
and/or grass catchers in place.
Working on banks can be dangerous.
– Do not mow excessively steep slopes.
– Always be sure of your footing on slopes or wet grass.
– Mow across the face of slopes – never up and down.
– Exercise extreme caution when changing direction on
slopes.
Use extreme caution when stepping back or pulling the ma-
chine towards you.
Never mow by pulling the mower towards you.
Stop the blades if the machine has to be tilted for transpor-
tation when crossing surfaces other than grass and when
transporting the machine to and from the area to be
mowed.
Do not tilt the machine when starting or switching on the
motor, except if the machine has to be tilted for starting in
long grass. In this case, do not tilt it more than absolutely
necessary and tilt only the part which is away from the operator. Always ensure that both hands are in the operating
position before returning the machine to the ground.
Switch on the motor according to the instructions with feet
well away from rotating parts.
Do not put hands or feet near or under rotating parts.
Always stand clear of the discharge zone when operating
the machine.
Never pick up or carry the machine while the motor is run-
ning.
F 016 L81 043 | (20.9.13) Bosch Power Tools
OBJ_BUCH-2040-001.book Page 3 Friday, September 20, 2013 10:44 AM
Keep supply cables and extension cables away from
the blade. The blade can cause damage to the cables and
lead to contact with live parts. Beware electric shock hazard.
Do not modify this product. Unauthorized modifications
may impair the safety of your product and may result in increased noise and vibration.
Avoid mowing in bad weather conditions especially when
there is a risk of lightning.
Remove the plug from the socket:
– whenever you leave the machine,
– before clearing a blockage,
– before checking, cleaning or working on the machine,
– after striking a foreign object. Inspect the machine for
damage and make repairs as necessary,
– if the machine starts to vibrate abnormally (check immedi-
ately).
Power supply
The voltage indicated on the rating plate must correspond
to the voltage of the power source.
We recommend that this equipment is only connect ed into
a socket which is protected by a circuit-breaker that would
be actuated by a 30 mA residual current.
Only use or replace power supply cables for this unit which
correspond to the types indicated by the manufacturer.
Never touch the mains plug with wet hands.
Do not run over, crush or pull the power supply cable or ex-
tension lead, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.
The extension lead must have a cross section in accord-
ance with the operating instructions and be protected
against splashed water. The connection must not be in water.
Electrical Safety
Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or entangled.
The blades continue to rotate for a few seconds after
the machine is switched off.
Caution – do not touch the rotating blade.
Your machine is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch Service Centre for details.
Extension cords/leads should only be used if they comply
with H05VV-F, H05RN-F types or IEC type design (60227
IEC 53, 60245 IEC 57).
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used:
–1.0mm
–1.5 mm
–2.5 mm
2
: max. length 40 m
2
: max. length 60 m
2
: max. length 100 m
Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
WARNING! Inadequate extension cables can be dan-
gerous. Extension cable, plug and socket must be of
watertight construction and intended for outdoor use.
It is recommended for increased electrical safety to use a Residual Current Device (RCD) with a tripping current of not
more than 30 mA. Always ch eck your RCD every time you use
it.
If the supply cord is damaged, please contact your nearest
Bosch Service Centre.
For products not sold in GB:
WARNING: For your safety, it is required that the plug attached to the machine is connected with the extension cord.
The coupling of the extension cord m ust be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
The connection lead must be inspected for signs of visible
damage and ageing at regular intervals and may only be used
if in perfect condition.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains socket elsewhere.
Maintenance
Always wear gardening gloves when handling or work-
ing near the sharp blades.
Keep all nuts, bolts and screws tight to be sure that the ma-
chine is in safe working condition.
Check the grass catcher frequently for wear or deteriora-
tion.
Examine the machine and replace worn or damaged parts
for safety.
Ensure replacement parts fitted are Bosch approved.
Symbols
The following symbols are important for reading and understanding the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the garden product in a better
and safer manner.
Symbol Meaning
English | 3
Movement direction
Bosch Power Tools F 016 L81 043 | (20.9.13)
OBJ_BUCH-2040-001.book Page 4 Friday, September 20, 2013 10:44 AM
4 | English
Symbol Meaning
Wear protective gloves
Weight
Switching On
Switching Off
Symbol Meaning
Permitted action
Prohibited action
Accessories/Spare Parts
Intended Use
The garden product is intended for domestic lawn mowing.
Technical Data
Lawnmower Rotak 34 R
Article number
Rated power input
Blade width
Height of cut
Grassbox, capacity
Weight according to EPTA-Procedure 01/2003
Protection class
Serial number see type plate on the garden product
The values given are valid for a nominal voltage [U] of 230 V. For different vol tages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your gard en product. The trade names of the individual garden products may vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.36 ohm.
Noise/Vibration Information
Measured sound values determined according to
2000 /14/ EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 82.5 dB(A); sound power level
95 dB(A). Uncertainty K =1 dB.
Vibration total values a
determined according to EN 60335:
<2.5m/s2, K =1.5 m/s2.
a
h
(triax vector sum) and uncertainty K
h
Declaration of Conformity
We declare under our sole responsibility that the product described under “Technical data” is in conformity with the following standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 96 dB (A). Conformity assessment procedure according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS4,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
25.06.2013
Mounting and Operation
Action Figure
Delivery Scope 1
Wheel Assembly 2
Handle Assembly 3
Snap together the Grassbox 4
Grassbox fitting/removing 4
Adjusting the Cutting Height 5
Starting 6
Stopping 6
Working Advice 6 – 7
Blade Maintenance 8
Selecting Accessories 9
W 1300 1400
cm 34 37
mm 20 – 70 20 – 70
kg 11.3 12.3
Rotak 340 R
3 600 HA6 1.. 3 600 HA6 2..
l4040
/II / II
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Rotak 37 R
Rotak 370 R
F 016 L81 043 | (20.9.13) Bosch Power Tools
Loading...