Bertazzoni PM6V), PM6040X, PM6V B, P604LMODХ, PM60 3 0 X User Manual

Loading...
Bertazzoni PM6V), PM6040X, PM6V B, P604LMODХ, PM60 3 0 X User Manual

(GB)

INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE

pag. 2

AND USE OF FIXED HOBS WITH GAS OR MIXED SUPPLY

 

DIMENSIONS: (605 mm)(W) x (520 mm)(D)

 

Models PM6030X

(TYPE PM6V)

‘A’

 

Models PM6040X

(TYPE PM6V)

‘B’

(FR) INSTRUCTIONS POUR L'INSTALLATION, L'ENTRETIEN ET

page. 8 L'UTILISATION DES TABLES DE CUISSON ENCASTRABLES GAZ ET MIXTES

DIMENSION: (605 mm)(W) x (520 mm)(D)

Modeles PM6030X

(MODELE PM6V) ‘A’

Modeles PM6040X

(MODELE PM6V) ‘B’

310678

(GB)

Read this instruction booklet before installing and using the appliance.

The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance.

The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics.

This appliance has been designed for non-professional, domestic use only.

THIS APPLIANCE HAS BEEN DESIGNED FOR NON PROFESSIONAL USE IN HOUSEHOLDS.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and Electronic Equipment.

This appliances is not indended to be used by people (children included) with reduced psychic and motor capacities, or with lack of experience and knowledge, unless there is supervision or instruction on the use of the appliance by a person responsible for their safety ‘’ Children must be supervised to make sure that they do not play with the appliance’’

TECHNICAL MANUAL FOR THE INSTALLER

INFORMATION FOR THE INSTALLER

The installation, all regulations, changes and maintenance referred to in this part must only be carried out by qualified staff. A wrong installation can cause damage to persons, animals or things which the manufacturer cannot be held responsible for.

The safety and automatic regulation devices on the appliances can only ever be changed by the manufacturer or by the supplier which has been authorised to do so.

INFORMATION FOR THE INSTALLER

The installation, all regulations, changes and maintenance referred to in this part must only be carried out by qualified staff.

A wrong installation can cause damage to persons, animals or things which the manufacturer cannot be held responsible for.

The safety and automatic regulation devices on the appliances can only ever be changed by the manufacturer or by the supplier which has been authorised to do so.

Inserting the hotplate

After having removed the various loose parts from the internal and external packing, make sure that the hotplate in not damaged and is suitable for the specific gas usage. The gas type label is on the underside of the hotplate base.

In case of doubt, do not use the appliance and contact skilled personnel.

Keep all the packing parts (polystyrene foam, cardboard, staples, etc.) away from children.

Consider the critical dimensions of the appliance, before making an opening in the top surface of the bench top. (relative measurements as per Fig 1- 2).

Requirements

1. Overhead clearances (Minimum values)

The minimum overhead clearances shall be in accordance with the minimum values indicated in the table n.1 and are shown and in the fig. 1- 2

Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the top of the highest burner of the cooking appliance and the range hood be less than 650mm.

Any other downward facing combustible surface less than 600mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area.

However, in no case shall this clearance to any surface be less than 450mm. Maximum depth for the overheads cabinet is 330mm

2

2. Side clearances (Minimum values)

The different side clearances shall be in accordance with the minimum values indicated in the table n.1 and are shawn and in the fig. 1- 2

The cooking surface area is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs.

Table n.1

Hobs models

Type A - B

 

Hobs models

Type A - B

Min. Clearances

(mm)

 

Min. Clearances

(mm)

L1

500

 

L10

560

L2

40

 

L11

915

L3

70

 

W

605

L4

457

 

D

520

L5

610

 

B1 (*)

60

L6

330

 

B2 (*)

152

L7

925

 

B3 (*)

60

L8

40

 

B4 (*)

152

L9

172

 

 

 

(*) Note:

-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.

-B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if present).

-B3 is the min. clearance between the back edge of the appliance and the back wall.

Attaching the hotplate

To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. To apply this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing strips along the edges of the opening in the bench top and carefully overlap the strip end. (See Fig. 3). insert the hotplate into the bench top opening. With a screwdriver assemble the brackets to the hotplate bottom by means of the screws . (See Fig. 3A-3B). Slide the hooks into position and secure them with the screws.

Trim the part of the sealing strips which extend beyond the hotplate base

IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE

The hob can be installed by itself, in an isolated position or inserted between two kitchen units or between one kitchen unit and a wall. Furthermore the back wall and surrounding surfaces must resist a temperature of 65 K.

To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the two surfaces together must resist temperatures of up to 150 °C

The installation of the appliance must be carried out according to the norms in force of the country concerned and the appliance must be installed in a well ventilated place.

This appliance is not equipped with devices to remove the products of combustion. The appliance must therefore be connected following the norms for installation mentioned above. Special attention must be paid to the information below regarding aeration and ventilation of the premises.

VENTILATION OF THE PREMISES

To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed is continuously ventilated. The volume of the premises must not be less than 25 m³ and the quantity of air needed must be based on the regular combustion of gas and on the ventilation of the premises. The natural flow of air will take place through permanent openings made in the wall of the premises to be ventilated: these openings will be connected to the outside and must have a minimum section of 100 cm² ( see Fig. 4 ).

These openings must be made in such a way that they cannot be obstructed.

3

POSITION AND VENTILATION

The cooking appliances that use gas must always remove the products of combustion via a hood linked to chimneys, chimney flues or via a direct connection to the outside ( see Fig. 5A ). If it is not possible to fit a hood it is possible to use a fan, fitted on the window or facing directly outside, which operates when the appliance is in use. ( see Fig. 5B ). In this way the norms in force of the country concerned regarding the ventilation of premises are strictly followed.

CONNECTING THE APPLIANCE TO THE GAS SUPPLY

Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the gas supply which is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it.

Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply.

A label on the last page of this manual and on the lower part of the case indicates the conditions for regulating the appliance: type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country concerned and it must only be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical male in accordance with the norms UNI-ISO 228-1. (Fig. 6-7)

CONNECTION OF THE APPLIANCE TO THE ELECTRICITY SUPPLY:

Connection to the electricity supply must be carried out according to the norms and indications of the law in force.

Before carrying out the connection check that:

- The electric charge of the system and the sockets are suitable for the maximum power of the appliance ( see label on the lower part of the case ).

-The socket or system is equipped with an efficient earth connection according to the norms and indications of the law currently in force. No responsibility can be held if these indications are not respected.

When the connection to the electricity supply is made with a socket.

Fit onto the electric cable a standard plug ( if it is not provided ) which is appropriate for the charge indicated on the label. Connect up the wires according to the diagram in Fig. 8 taking care to respect the corresponding pairs listed below:

letter L (phase) = brown coloured wire; letter N (neutral) = blue coloured wire;

symbol”earth = green-yellow coloured wire;

-The electric cable must be positioned so that it cannot reach a temperature of over 75 K at any point.

-Do not use reducers, adapters or shunts for the connection as they could cause false contacts and subsequent dangerous overheating.

When the connection is made directly with the electricity supply:

-To connect the appliance directly to the supply mains, a means for disconnection having a contact separation in all poles that provide full disconnection under overvoltage category III conditions, must be incorporated in the fixing wiring, according with the wiring rules.

-Remember that the earth wire must not be interrupted by the switch.

-Alternatively the electrical connection can also be protected by a differential switch of high sensitivity.

-You are strongly advised to fix the special yellow-green earth wire to an efficient earthing system

ATTENTION: The appliance conforms with the regulations of directives 90/396EEC (Gas Directive) regarding gas appliances for domestic use and the like, 93/68 and 73/23 (Low Voltage Directive) regarding electrical safety and 2004/108/CE, 93/68 and 89/336 (EMC Directive) regarding electromagnetic compatibility.

Wiring diagrams

Wiring diagram description

 

For hotplate see Fig. 13.

1.

Cable terminal

L. Black

 

2.

Ignition switch

N. White

 

3.

Spark generator

T. Green (earth)

 

4.

Ignition spark

 

4

MAINTENANCE OF THE MACHINE

CHANGING THE PARTS

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

To replace different components such as burners, taps and electrical parts you must take out the hob from the kitchen unit by releasing the fixing hooks, unscrew the fixing screws of the burners on the work top, unscrew the fixing nuts of the electric plates which are visible on the lower part of the hob and remove the worktop in order to carry out the replacement of the defective parts.

NOTE: If the taps need replacing you also need to unscrew the two fixing screws of the gas ramp at the bottom of the hob which are found on the upper part of the latter.

For appliances equipped with automatic “ON” switches you must dismantle the “ON” switch chain before replacing the taps.

You are advised to change the seal on the tap every time you replace a tap in order to ensure a perfect hold between the body and ramp.

WARNING: The electric cable which is provided with the appliance is connected to the appliance with a type X connection and thus can be replaced with the same type of cable as that installed without using special tools. In the event of wear or damage to the mains cable, replace it with :

Type/ section of mains cable H05VV-F 3x0,75 mm2 or H05RR-F 3x0,75 mm2

WARNING: If you replace the electric mains cable the installer must have the earth conductor about 2 cm longer than the phase conductors and must also take heed of the warnings regarding electric connection.

Room ventilation – Location and venting.

ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the national standards in force.

ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity with the national standards in force.

- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:

To change the nozzles of the burners use the following procedure:

Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE A shown below.

TABLE N°2: Adapting to different types of gas

 

 

 

APPLIANCE CATEGORY:

III

 

Burner

Type of Gas

Pressure

Nozzle

 

Nominal Charge

Reduced Charge

Diameter

 

 

 

 

diameter

 

 

 

 

 

 

 

 

by-pass 1/100mm

 

 

 

mbar

1/100mm

g/h

l/h

Kw

 

kcal/h

kw

 

kcal/h

 

 

Town

G110

8

145

-

227

1,00

 

860

0,30

 

258

27 reg

Auxiliary

Natural

G20

20

77

-

95

1,00

 

860

0,30

 

258

27 reg

 

Butane

G30

28

50

73

-

1,00

 

860

0,30

 

258

27

 

Propane G31

37

50

71

-

1,00

 

860

0,30

 

258

27

 

Town

G110

8

192

-

397

1,75

 

1505

0,44

 

378

31 reg

Semi-

Natural

G20

20

101

-

167

1,75

 

1505

0,44

 

378

31 reg

Rapid

Butane

G30

28

66

127

-

1,75

 

1505

0,44

 

378

31

 

Propane G31

37

66

125

-

1,75

 

1505

0,44

 

378

31

 

Town

G110

8

280

-

681

3

 

2580

0,75

 

645

42 reg

 

Natural

G20

20

129

-

286

3

 

2580

0,75

 

645

42 reg

Rapid

Butane

G30

28

87

218

-

3

 

2580

0,75

 

645

42

 

Propane G31

37

87

214

-

3

 

2580

0,75

 

645

42

 

Town

G110

8

130

-

181

0,8

 

688

0,30

 

258

27 reg

Dual

Natural

G20

20

70

-

76

0,8

 

688

0,30

 

258

27 reg

burner

Butane

G30

28

46

211

-

0,8

 

688

0,30

 

258

27

inner

Propane G31

37

46

207

-

0,8

 

688

0,30

 

258

27

 

Town

G110

8

2x300

-

885

4,4

3784

1.8

 

1548

65 reg

Dual

Natural

G20

20

2x110

-

419

4,4

3784

1.8

 

1548

65 reg

burner

Butane

G30

28

2x69

298

-

4,1

3526

1.8

 

1548

65

outer

Propane G31

37

2x69

293

-

4,1

3526

1.8

 

1548

65

CAUTION: save the orifices removed from the appliance for future use

Regulation of burners

Regulation of the "MINIMUM" on the burners

To regulate the minimum on the burners carry out the following procedure indicated below:

1)Turn on the burner and put the knob onto position MINIMUM ( small flame ).

2)Remove the knob ( Fig. 10) of the tap which is set for standard pressure. The knob is found on the bar of the tap itself.

5

+ 11 hidden pages