Asus RS700D-E6/PS8 User Manual

RS700D-E6/PS8
1U Rackmount Server User Guide
E4519
First Edition
March 2009
Copyright © 2009 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product.
Specications and information contained in this manual ae furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe.
ii
Contents
Notices ........................................................................................................ vii
Safety information .................................................................................... viii
About this guide ......................................................................................... ix
Chapter 1: Product introduction
1.1 System package contents ........................................................... 1-2
1.2 Serial number label ...................................................................... 1-2
1.3 Systemspecications ................................................................. 1-3
1.4 Front panel features ..................................................................... 1-5
1.5 Rear panel features ...................................................................... 1-5
1.6 Internal features ........................................................................... 1-6
1.7 LED information ........................................................................... 1-7
1.7.1 Front panel LEDs ............................................................ 1-7
1.7.2 LAN (RJ-45) LEDs .......................................................... 1-7
1.7.3 HDD status LED .............................................................. 1-8
Chapter 2: Hardware setup
2.1 Chassis cover ............................................................................... 2-2
2.2 Central Processing Unit (CPU) ................................................... 2-3
2.1.1 Installing the CPU ........................................................... 2-3
2.2.2 Installing the CPU heatsink and airduct .......................... 2-6
2.3 System memory ........................................................................... 2-7
2.2.1 Overview ......................................................................... 2-7
2.3.2 Memory Congurations ................................................... 2-8
2.3.3 Installing a DIMM ............................................................ 2-9
2.3.4 Removing a DIMM .......................................................... 2-9
2.4 Hard disk drives ......................................................................... 2-10
2.5 Expansion slot ............................................................................ 2-11
2.5.1 Installing an expansion card to the riser card bracket ....2-11
2.5.2 Conguring an expansion card ..................................... 2-12
2.6 Cable connections ..................................................................... 2-13
2.7 Removable/optional components ............................................. 2-14
2.7.1 Replacing system fans .................................................. 2-14
2.7.2 Replacing power supply units ....................................... 2-15
2.7.3 Installing ASMB4 series management board (optional) 2-16
iii
Contents
Chapter 3: Installation options
3.1 Rackmount rail kit items (optional) ............................................ 3-2
3.2 Attaching the rails to the server ................................................. 3-2
3.3 Attaching the rack rails ............................................................... 3-3
3.4 Rackmounting the server ............................................................ 3-4
Chapter 4: Motherboard Info
4.1 Motherboard layout ...................................................................... 4-2
4.2 Jumpers ........................................................................................ 4-4
4.3 Internal connectors ...................................................................... 4-8
4.4 Internal LEDs .............................................................................. 4-16
Chapter 5: BIOS setup
5.1 Managing and updating your BIOS ............................................ 5-2
5.1.1 AFUDOS utility ................................................................ 5-2
5.1.2 ASUS CrashFree BIOS 3 utility ...................................... 5-4
5.2 BIOS setup program .................................................................... 5-5
5.2.1 BIOS menu screen .......................................................... 5-6
5.2.2 Menu bar ......................................................................... 5-6
5.2.3 Navigation keys ............................................................... 5-6
5.2.4 Menu items ..................................................................... 5-7
5.2.5 Sub-menu items .............................................................. 5-7
5.2.6 Conguration elds ......................................................... 5-7
5.2.7 Pop-up window ............................................................... 5-7
5.2.8 Scroll bar ......................................................................... 5-7
5.2.9 General help ................................................................... 5-7
5.3 Main menu .................................................................................... 5-8
5.3.1 System Time ................................................................... 5-8
5.3.2 System Date ................................................................... 5-8
5.3.3 SATA1–4 ......................................................................... 5-8
5.3.4 IDE Conguration .......................................................... 5-10
5.3.5 AHCI Conguration ........................................................5-11
5.3.6 System Information ....................................................... 5-12
5.4 Advanced menu ......................................................................... 5-13
5.4.1 CPU Conguration ........................................................ 5-13
iv
Contents
5.4.2 Chipset Conguration ................................................... 5-16
5.4.3 Legacy Device Conguration ........................................ 5-20
5.4.4 USB Conguration ........................................................ 5-21
5.4.5 PCIPnP Conguration ................................................... 5-22
5.4.6 Power On conguration ................................................ 5-23
5.4.7 Event Log Conguration ............................................... 5-24
5.4.8 Hardware Monitor ......................................................... 5-25
5.4.9 PCI Express Conguration ............................................ 5-26
5.4.10 ACPI Conguration ....................................................... 5-27
5.5 Server menu ............................................................................... 5-29
5.5.1 Remote Access Conguration ....................................... 5-29
5.6 Boot menu .................................................................................. 5-31
5.6.1 Boot Device Priority ...................................................... 5-31
5.6.2 Boot Settings Conguration .......................................... 5-32
5.6.3 Security ......................................................................... 5-33
5.7 Exit menu .................................................................................... 5-35
Chapter6: RAIDconguration
6.1 Setting up RAID ............................................................................ 6-2
6.1.1 RAID denitions .............................................................. 6-2
6.1.2 Installing hard disk drives ................................................ 6-2
6.1.3 RAID controller selection ................................................ 6-3
6.1.4 Setting the RAID item in BIOS ........................................ 6-3
6.2 LSISoftwareRAIDCongurationUtility .................................... 6-4
6.2.1 Creating a RAID set ........................................................ 6-5
6.2.2 Adding or viewing a RAID conguration ........................6-11
6.2.3 Initializing the virtual drives ........................................... 6-12
6.2.4 Rebuilding failed drives ................................................. 6-16
6.2.5 Checking the drives for data consistency ..................... 6-18
6.2.6 Deleting a RAID conguration ....................................... 6-21
6.2.7 Selecting the boot drive from a RAID set ...................... 6-22
6.2.8 Enabling WriteCache .................................................... 6-23
6.3 Intel® Matrix Storage Manager Option ROM Utility ................. 6-24
6.3.1 Creating a RAID set ...................................................... 6-25
6.3.2 Creating a Recovery set ............................................... 6-26
v
Contents
6.3.3 Deleting a RAID set ...................................................... 6-28
6.3.4 Resetting disks to Non-RAID ........................................ 6-29
6.3.5 Recovery Volume Options ............................................ 6-30
6.3.6 Exiting the Intel® Matrix Storage Manager .................... 6-31
6.3.7 Rebuilding the RAID ..................................................... 6-31
6.3.8 Setting the Boot array in the BIOS Setup Utility ............ 6-33
Chapter 7: Driver installation
7.1 RAID driver installation ............................................................... 7-2
7.1.1 Creating a RAID driver disk ............................................ 7-2
7.1.2 Installing the RAID controller driver ................................ 7-5
7.2 Intel® chipset device installation .............................................. 7-12
7.3 LAN driver installation ............................................................... 7-14
7.4 VGA driver installation............................................................... 7-17
7.5 Management applications and utilities installation ................ 7-19
7.5.1 Running the support DVD ............................................. 7-19
7.5.2 Drivers menu ................................................................. 7-19
7.5.3 Utilities menu ................................................................ 7-20
7.5.4 Make disk menu ............................................................ 7-20
7.5.5 Contact information ....................................................... 7-20
vi

Notices

Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations. Changes
or modications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class A digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction
of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://green.asus.com/english/REACH.htm.
vii

Safety information

Electrical Safety
Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
When adding or removing any additional devices to or from the system, contact a qualied service technician or your dealer. Ensure that the power cables for
the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you service.
If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your dealer.
Operation Safety
Servicing of this product or units is to be performed by trained service personnel only.
Before operating the server, carefully read all the manuals included with the
server package.
Before using the server, make sure all cables are correctly connected and the
power cables are not damaged. If any damage is detected, contact your dealer as soon as possible.
To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
viii
This product is equipped with a three-wire power cable and plug for the user’s safety. Use the power cable with a properly grounded electrical outlet to avoid electrical shock.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or
carrying the system.
DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

About this guide

Audience
This user guide is intended for system integrators, and experienced users with at
least basic knowledge of conguring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections
on front panel and rear panel specications.
2. Chapter 2: Hardware setup
This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
3. Chapter 3: Installation options
This chapter describes how to install the optional components and devices into the barebone server.
4. Chapter 4: Motherboard information
This chapter includes the motherboard layout and brief descriptions of the jumpers and internal connectors.
5. Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters.
6. Chapter6:RAIDconguration
This chapter provides instructions for setting up, creating and conguring
RAID sets using the available utilities.
7 Chapter 7: Driver installation
This chapter provides instructions for installing the necessary drivers for different system components.
ix
Conventions
To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when
trying to complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Italics
<Key> Keys enclosed in the less-than and greater­ than sign means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or Return key.
<Key1+Key2+Key3> If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command
exactly as shown, then supply the required item or value enclosed in brackets.
Example: At the DOS prompt, type the command line:
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Means that you must type the command
format A:/S
References
Refer to the following sources for additional information, and for product and software updates.
1. ASUS Server Web-based Management (ASWM) user guide
This manual tells how to set up and use the proprietary ASUS server management utility.
2. ASUS websites
The ASUS websites worldwide provide updated information for all ASUS hardware and software products. Refer to the ASUS contact information.
x
Chapter 1
This chapter describes the general features of the server, including sections on front panel and rear panel
specications.
ASUS RS700D-E6/PS8
Product introduction

1.1 System package contents

Check your system package for the following items.
Model Name RS700D-E6/PS8 Chassis ASUS R12B 1U Rackmount Chassis Motherboard ASUS Z8NH-D12 Server Board Component 2 x 770W Single Power Supply
Accessories 1 x RS700D-E6/PS8 User’s Guide
Optional Items CPU Heatsink
* ASUS System Web-based Management
**ThesystemdoesnotincludeaUSBoppydrive.YoumayhavetouseaUSBoppydrivewhen
creating a SATA RAID driver disk. Refer to Chapter 7 for details.
8 x Hot-swap 2.5” HDD trays 1 x SAS/SATA2 Backplane 2 x PCI Riser Card (ASUS RE16R-R12B) 2 x Front I/O Board (ASUS FPB-AR14) 1 x Redundant Power Supply Power Distribution Board (ASUS PDB-R12B) 8 x System Fans (40mm x 56mm)
1 x ASUS ASWM 2.0 User’s Guide 1 x RS700D-E6/PS8 Support CD (including ASWM*) 1 x Bag of Screws 2 x AC Power Cables 1 x Semi-ball Bearing Rail Kit
ASUS ASMB4-iKVM Remote management card
Anti-virus Software CD ASUS PIKE series SAS RAID card
If any of the above items is damaged or missing, contact your retailer.

1.2 Serial number label

Before requesting support from the ASUS Technical Support team, you must take note of the product’s serial number containing 12 characters such as xxxxxxxxxxxx. See the gure below.
With the correct serial number of the product, ASUS Technical Support team
members can then offer a quicker and satisfying solution to your problems.
RS700D-E6-P
xxxxxxxxxxxx
Chapter 1: Product introduction1-2
1.3 Systemspecications
The ASUS RS700D-E6/PS8 is a 1U barebone server system featuring the ASUS Z8NH-D12 server board. The server supports Intel® LGA1366 Xeon® 5500 series
processors, plus other latest technologies through the chipsets onboard.
Model Name RS700D-E6/PS8
2 x Socket LGA1366 per Node
- Quad-Core Intel® Xeon® X5500 Series (95W)
Processor / System Bus
Core Logic
ASUS Features
Memory
Expansion Slots
Storage SATA Controller
HDD Bays
Networking LAN Graphic VGA
Onboard I/O
Smart Fan ASWM2.0
Total Slots
Capacity
Memory Type
Memory Size
Total PCI/PCI-X/ PCI-E Slots
Slot Type
I = internal A or S will be hot-swappable
- Quad-Core Intel® Xeon® E5500 Series (80W)
- Quad-Core Intel® Xeon® L5500 Series
(60W/38W) QPI 4.8 / 5.86 / 6.4 GT/s
Intel® 5500 I/O Hub Intel® ICH10R I/O Controller
√ √ 12 DIMMs per Node (3-channel per CPU,
6 DIMMs per CPU)
Maximum up to 96GB (RDIMM) per Node Maximum up to 48GB (UDIMM) per Node
DDR3 1333 / 1066 / 800 Reg DIMM / Unbuffered
DIMM with ECC
1GB, 2GB, 4GB and 8GB (RDIMM) 1GB, 2GB and 4GB (UDIMM)
1 per Node
1 x PCI-E 2.0 x16 slot (x16 link) (Low prole / HL) per Node
4 x SATA2 300MB/s ports Intel Matrix Storage (for Windows only)
- Supports software RAID 0, 1, 5 & 10 LSI MegaRAID (for Linux / Windows)
- Supports software RAID 0, 1 & 10
4 x Hot-swap 2.5” HDD Bays per Node (Total 8 x 2.5” HDD in 1U)
2 x Intel® 82574L PCIE GbE LAN per Node Aspeed AST2050 8MB
Per Node:
- 1 x External Serial Port
- 3 x RJ-45 ports (1 for ASMB4-iKVM)
- 3 x USB 2.0 ports (Front x 1, Rear x 2)
- 1 x VGA port
- 1 x Internal A-type USB Port
(continued on the next page)
ASUS RS700D-E6/PS8 1-3
Windows® Server 2008 Enterprise 32 / 64-bit Windows® Server 2003 R2 Enterprise 32 / 64-bit
OS Support
RedHat® Enterprise Linux AS5.0 32 / 64-bit SuSE® Linux Enterprise Server 10 32 / 64-bit (Subject to change without any notice)
Anti-virus Software
Optional anti-virus CD Pack
Out of Band Management Solution
Remote
Hardware
Software Dimension (HH x WW x DD) Net Weight Kg (CPU, DRAM &
HDD not inclu ded) Power Supply
Optional ASMB4-iKVM for KVM-over-IP support
ASUS ASWM 2.0
686mm x 444mm x 43.4mm
16.5 Kg
770W (80+) Cold-Swap Power Supply per Node Operation temperature: 10°C ~ 35°C / Non operation
Environment
temperature: -40°C ~ 70°C Non operation humidity: 20% ~ 90% ( Non-
condensing)
*Specicationsaresubjecttochangewithoutnotice.
®
Chapter 1: Product introduction1-4

1.4 Front panel features

The barebone server displays a simple yet stylish front panel with easily accessible
features. The power and reset buttons, LED indicators, and USB port for each
Node are located on the front panel.
Rack screw
Refer to section
Hot-swap HDD bays
Hot-swap HDD bays
1.7.1 Front panel LEDs
Power button
Reset button
Location switch
USB port
for the LED descriptions.
Power LED Message LED Location LED LAN1 LED LAN2 LED HDD Access LED
Hot-swap HDD bays
Hot-swap HDD bays
Rack screw

1.5 Rear panel features

The rear panel includes the expansion slots, system power sockets, and rear fans. The I/O shields with openings for the rear panel connectors on the motherboard are also placed in the real panel.
The ports for the USB, VGA, and Gigabit LANs do not appear on the rear panel
if the motherboards are not present.
LAN port 1
LAN port*
USB ports
LAN port 2
Serial port
VGA port
Location LED
Power supply fan
Power cord connector
LAN port*
Power supply fan
Power cord connector
USB ports
LAN port 1
LAN port 2
Serial port
VGA port
Location LED
* These ports are for ASUS ASMB4-iKVM controller cards only.
ASUS RS700D-E6/PS8 1-5

1.6 Internal features

The barebone server includes the basic components as shown.
1. Power supplies and power
2
1
3
2
1
3
4
5
6 7 8
10
10
9
fans
2. PCI Express x16 slot Riser
Cards (at x16 link)
3. ASUS Z8NH-D12 server
boards
4. System fans
5. SATA/SAS backplane (hidden)
6. Hot-swap HDD tray 1 and 3—Connect to SATA1 and SATA3 ports
7. Hot-swap HDD tray 2 and 4—Connect to SATA2 and
SATA4 ports
8. Hot-swap HDD tray 1 and 3—Connect to SATA1 and SATA3 ports
9. Hot-swap HDD tray 2 and 4—Connect to SATA2 and
SATA4 ports
10. Front I/O boards (hidden)
The barebone server does not include a oppy disk drive and an optical disc drive. Connect a USB oppy disk drive or a USB ODD to any of the USB ports on the front or rear panel if you need to use a oppy disk or a optical disc.
*WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
Chapter 1: Product introduction1-6

1.7 LED information

1.7.1 Front panel LEDs

Power LED Message LED Location LED
HDD Access LED
LAN2 LED
LAN1 LED
LED Icon
Power LED
HDD Access LED
Message LED
Location LED
LAN LEDs
Display status
ON System power ON
OFF
Blinking
OFF
Blinking
OFF ON
OFF Blinking ON
Description
No activity Read/write data into the HDD
System is normal; no incoming event ASWM indicates a HW monitor event
Normal status Location switch is pressed (Press the location switch again to turn off)
No LAN connection LAN is transmitting or receiving data LAN connection is present

1.7.2 LAN (RJ-45) LEDs

SPEED LED
ACT/LINK LED
ACT/LINK LED SPEED LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
GREEN Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
ASUS RS700D-E6/PS8 1-7

1.7.3 HDD status LED

HDDLEDStatusDene
Power
LED Status Description
LED
Active LED
Power
Active Green Blink Data read/write to HDD
Green Light ON Power On (detection HDD present)
Red Light ON
G/R Blinking RAID rebuilding OFF HDD not found
RAID HDD fail (HDD plug-in ready but detection error)
Chapter 1: Product introduction1-8
Chapter 2
This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
ASUS RS700D-E6/PS8
Hardware setup

2.1 Chassis cover

Removing the rear cover
1. Loosen the two thumbscrews on the rear panel to release the rear cover from the chassis.
Thumbscrews
2. Firmly hold the cover and slide it
toward the rear panel for about half an inch until it is disengaged from the chassis.
1/2 inch distance
3. Lift the cover from the chassis.
Chapter 2: Hardware setup2-2

2.2 Central Processing Unit (CPU)

The motherboard comes with dual surface mount LGA 1366 Socket designed for
the Intel® Xeon 5500 series CPU in the Land Grid Array (LGA) package.
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS shoulders the repair cost only if the damage is shipment/transit-related.
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the Socket 1366.
The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/ incorrect removal of the PnP cap.

2.1.1 Installing the CPU

To install a CPU:
1. Locate the CPU socket on the motherboard.
Before installing the CPU, ensure that the socket box is facing towards you and
the load lever is on your left.
2-3ASUS RS700D-E6/PS8
2. Press the load lever with your
thumb (A), then move it to the left
(B) until it is released from the
retention tab.
Retention tab
A
To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
3. Lift the load lever in the direction of the arrow to a 135º angle.
4. Lift the load plate with your thumb
and forenger to a 100º angle.
5. Remove the PnP cap from the CPU socket.
B
Load lever
Load plate
4
3
PnP cap
Chapter 2: Hardware setup2-4
6. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the
socket, and then t the socket
alignment key into the CPU notch.
The CPU ts in only one correct
orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the
socket and damaging the CPU!
7. Apply several drops of thermal paste to the exposed area of the CPU that the heatsink will be in contact with, ensuring that it is spread in an even thin layer.
Some heatsinks come with pre­applied thermal paste. If so, skip this step.
The thermal paste is toxic and inedible. If it gets into your eyes or touches your skin, ensure to wash it off immediately and seek professional medical help.
Gold triangle mark
CPU notch
Alignment key
To prevent contaminating the paste, DO NOT spread the paste with your nger
directly.
8. Close the load plate (A), and then
push the load lever (B) until it snaps
into the retention tab.
A
B
2-5ASUS RS700D-E6/PS8

2.2.2 Installing the CPU heatsink and airduct

To install the CPU heatsink:
1. Place the heatsink on top of the installed CPU, ensuring that the four fasteners match the holes on the motherboard.
2. Twist each of the four screws with a Philips (cross) screwdriver just enough to attach the heatsink to the motherboard. When the four screws are attached,
tighten them one by one to completely secure the heatsink.
A
B
B
Tighten the four heatsink screws in a diagonal sequence.
A
Chapter 2: Hardware setup2-6

2.3 System memory

2.2.1 Overview

The motherboard comes with twelve (12) Double Data Rate 3 (DDR3) Dual Inline
Memory Modules (DIMM) sockets.
The gure illustrates the location of the DDR3 DIMM sockets:
2-7ASUS RS700D-E6/PS8
2.3.2 MemoryCongurations
You may install 1 GB, 2 GB, 4 GB, or 8GB registered / unbuffered ECC DDR3 DIMMs into the DIMM sockets using the memory congurations in this section.
Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the
same vendor. Refer to the Qualied Vendors List on the ASUS web site.
You may install varying memory sizes in Channel A, Channel B and Channel C. The system maps the total size of the lower-sized channel for the dual-channel or triple-channel conguration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
Due to the memory address limitation on 32-bit Windows OS, when you install 4GB or more memory on the motherboard, the actual usable memory for the OS can be about 3GB or less. For effective use of memory, we
recommend that you do any of the following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows OS.
- Install a 64-bit Windows OS when you want to install 4GB or more on the
motherboard. For more details, refer to the Microsoft® support site at
http://support.microsoft.com/kb/929605/en-us.
This motherboard does not support DIMMs made up of 256 Mb (32MB)
chips or less (Memory chip capacity counts in Megabit, 8 Megabit/Mb = 1
Megabyte/MB).
Memory population table
CPU1Conguration
DIMM_A2 DIMM_A1 DIMM_B2 DIMM_B1 DIMM_C2 DIMM_C1 1 DIMMs 2 DIMMs 3 DIMMs 4 DIMMs 6 DIMMs
CPU2Conguration
1 DIMMs 2 DIMMs 3 DIMMs 4 DIMMs 6 DIMMs
-- -- -- -- --
-- -- -- --
-- -- --
DIMM_D2 DIMM_D1 DIMM_E2 DIMM_E1 DIMM_F2 DIMM_F1
-- -- -- -- --
-- -- -- --
-- -- --
-- --
-- --
Chapter 2: Hardware setup2-8

2.3.3 Installing a DIMM

Ensure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
1. Unlock a DIMM socket by pressing the retaining clips outward.
2. Align a DIMM on the socket
such that the notch on the DIMM matches the break on the socket.
Unlocked retaining clip
A DIMM is keyed with a notch so that it ts in only one direction. DO NOT force
a DIMM into a socket to avoid damaging the DIMM.
2
DIMM notch
1
1
3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
Locked Retaining Clip

2.3.4 Removing a DIMM

Follow these steps to remove a DIMM.
1. Simultaneously press the retaining clips outward to unlock the DIMM.
1
Support the DIMM lightly with your ngers when pressing the retaining clips. The DIMM might get damaged when it ips out with extra force.
2. Remove the DIMM from the socket.
3
2
1
DIMM notch
2-9ASUS RS700D-E6/PS8

2.4 Hard disk drives

The system supports four hot-swap SATAII/SAS hard disk drives. The hard disk drive installed on the drive tray connects to the motherboard SATAII/SAS ports via the SATAII/SAS backplane. Follow the illustration below for HDD installation.
To install a hot-swap SATAII/SAS HDD
1. Release a drive tray by pushing the spring lock to the right, and then pulling the tray lever outward. The drive tray ejects slightly after you pull out the lever.
2. Firmly hold the tray lever and pull
the drive tray out of the bay.
3. Remove the drive tray supporting
pillar shown in the right gure.
Supporting pillar
4. Place a SATAII/SAS hard disk drive on the tray, and then secure it with four screws.
2
1
5. Carefully insert the drive tray and push it all the way to the depth of the bay until just a small fraction of the tray edge protrudes.
When installed, the SATAII/SAS connector on the drive connects to the SATAII/
SAS interface on the backplane.
6. Push the tray lever until it clicks, and secures the drive tray in place. The drive tray is correctly placed when its front edge aligns with the bay edge.
7. Repeat steps 1 to 5 if you wish to install a second SATAII/SAS drive.
Chapter 2: Hardware setup2-10

2.5 Expansion slot

2.5.1 Installing an expansion card to the riser card bracket

The barebone server comes with a riser card bracket. You need to remove the
bracket if you want to install PCI Express x16 expansion cards.
To install a PCI Express x16 card
1. Firmly hold the riser card bracket, and then pull it up to detach it from the PCI Express x16 slot on the motherboard.
2. Place the riser card bracket on a at and stable surface, and then
remove the screw from the slot bay.
PCI Express x16 slot
3. Install a PCI Express x16 card to the bracket as shown, and then secure the card with a screw.
4. Press the riser card bracket until the golden connectors completely
t the slot and the bracket aligns
with the rear panel.
5. Connect the cable(s) to the card, if applicable.
2-11ASUS RS700D-E6/PS8
2.5.2 Conguringanexpansioncard
After installing the expansion card, congure the it by adjusting the software
settings.
1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the following tables.
3. Install the software drivers for the expansion card.
Standard Interrupt assignments
IRQ Priority Standard function
0 1 System Timer 1 2 Keyboard Controller
2 - Programmable Interrupt 4* 12 Communications Port (COM1) 5* 13 --
6 14 Floppy Disk Controller 7* 15 --
8 3 System CMOS/Real Time Clock
9* 4 ACPI Mode when used 10* 5 IRQ Holder for PCI Steering 11* 6 IRQ Holder for PCI Steering 12* 7 PS/2 Compatible Mouse Port
13 8 Numeric Data Processor
14* 9 Primary IDE Channel 15* 10 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
Chapter 2: Hardware setup2-12

2.6 Cable connections

The bundled system cables are pre-connected before shipment. You do
not need to disconnect these cables unless you will remove pre-installed components to install additional devices.
Refer to Chapter 4 for detailed information on the connectors.
6
5
7
2
3
3
4
3
Pre-connected system cables
1. 20-pin SSI power connector (from power supply to motherboard)
2. 4-pin SSI power connector (from power supply to motherboard)
3. System fan connectors (from motherboard FRNT_FAN1, FRNT_FAN2,
FRNT_FAN3 and FRNT_FAN4 to system fans)
4. USB connector (from motherboard to front I/O board)
5. Panel connector (from motherboard to front I/O board)
6. SATA connectors (from motherboard to SATAII/SAS backplane board)
7. Auxiliary panel connector (from motherboard to front I/O board)
1
3
2-13ASUS RS700D-E6/PS8

2.7 Removable/optional components

You may need to remove previously installed system components when installing
or removing system devices. Or you may need to install the optional components into the system. This section tells how to remove/install the following components:
1. System fans
2. Power supply units
3. ASUS ASMB4-iKVM (optional)
Ensure that the system is turned off before removing any components.

2.7.1 Replacing system fans

To uninstall the system fans:
1. Disconnect the system fan cable from the fan connector on the motherboard.
2. Lift the fan, and then set aside.
3. Repeat step 1 to 2 to uninstall the
other system fans.
To reinstall the system fans
1. Insert the fan to the fan cage. The
airow directional arrow on the
fan side should point towards the system rear panel.
2. Connect the system fan cable to the
fan connector on the motherboard.
Chapter 2: Hardware setup2-14
3. Recover the rear cover. Press down gently on the location above the system fans to ensure proper fan installation, as shown in the
right gure.

2.7.2 Replacing power supply units

Follow the steps below to replace the failed power supply unit (PSU).
To replace the failed PSU
1. Hold the PSU lever and press the PSU latch.
2. Firmly pull the failed PSU out of the
server chassis.
3. Firmly push the new PSU into the chassis until the latch locks to the server chassis.
2-15ASUS RS700D-E6/PS8

2.7.3 Installing ASMB4 series management board (optional)

Follow the steps below to install an optional ASMB4 series management board on
your motherboard.
1. Locate the BMC_FW1 header on
the motherboard.
2. Orient and press the ASMB4
management card in place.
3. Insert the LAN cable plug to the LAN3 port for server management.
Chapter 2: Hardware setup2-16
Chapter 3
This chapter describes how to install the optional components and devices into the barebone server.
ASUS RS700D-E6/PS8
Installation options

3.1 Rackmount rail kit items (optional)

Your rackmount rail kit package contains:
two pair of server rails (for the server)
two pairs of rack rails (for the rack)
Nut-and-bolt type screws
Nuts and screws Rack railsRear end Front end

3.2 Attaching the rails to the server

To attach the server rails
1. Attach the front end of the server rail to the side of the chassis, matching each of the three hooks to the holes on the rail. Then slide the rail toward the front panel until it locks in place.
2. Attach the rear end of the server rail
to the side of the chassis with one screw.
Chapter 3: Installation options3-2
3. Attach the rear end of the server rail to the side of the chassis, matching each of the two hooks to the holes on the rail, and then slide the rail toward the front panel until it locks in place.
4. Secure the rear end of the server rail to the side of the chassis with one screw.
5. Repeat step 1 to 4 to attach the second server rail to the other side of the chassis.

3.3 Attaching the rack rails

To attach the rack rails
1. Select one unit of space (1U) on the rack where you want to install the barebone server.
2. Install the nuts on the holes of the 1U space on the rack front.
3. Install the nuts on the holes of the 1U space on the corresponding rack rear.
4. Measure the depth of the rack to determine the length of the rack rails.
5. Measure the rack rail when assembled to ensure that it ts the rack.
6. Position the rack rail to the 1U space on the rack. Ensure that the front end of the rack rail goes to the front of the rack space.
7. Secure the front end of the rail with two rack screws.
8. Secure the rear end of the rail with two rack screws.
9. Repeat steps 5 to 8 to assemble and attach the second rack rail.
3-3ASUS RS700D-E6/PS8

3.4 Rackmounting the server

To mount the server to the rack
1. Align the server rails with the rack rails, then push the server all the way to the depth of the rack.
2. Tighten the two rack screws to
secure the server in place.
To uninstall the server from the rack
1. Loosen the rack screws that secured the server to the rack.
2. Pull the server from the rack.
Remember to press the latches on both sides to release the server from the rack.
Chapter 3: Installation options3-4
Chapter 4
This chapter includes the motherboard layout and brief descriptions of the jumpers and internal connectors.
ASUS RS700D-E6/PS8
Motherboard Info

4.1 Motherboard layout

Chapter 4: Motherboard information4-2
Layout contents
Jumpers Page
1. Clear RTC RAM (CLRTC1) 4-4
2. VGA controller setting (3-pin VGA_SW1) 4-5
3. DDR3 voltage control setting (4-pin LVDDR3_SEL1,
LVDDR3_SEL2)
4. LAN controller setting (3-pin LAN_SW1, LAN_SW2) 4-6
5. Intel ICH10R® SATA ports S/W RAID setting (3-pin RAID_SEL1) 4-6
6. Force BIOS recovery setting (3-pin RECOVERY1) 4-7
Internal connectors Page
1. Serial ATA connectors (7-pin SATA1, SATA2, SATA 3, SATA4) 4-8
2. USB connector (5-1 pin USB3; A-Type USB4) 4-9
3. Front fan connectors (4-pin FRNT_FAN1, FRNT_FAN2,
FRNT_FAN3, FRNT_FAN4)
4. LPC debug card connector (14-1 pin LPC1) 4-11
5. Serial General Purpose Input/Output connector (6-1 pin SGPIO1) 4-11
6. BMC header (BMC_FW1) 4-12
7. Power Supply SMBus connectors (6-1 pin JP1, JP2) 4-12
8. Proprietary power connectors (20-pin PWR1, 20-pin PWR2, 4-pin PWR3)
9. System panel connector (20-pin PANEL1) 4-14
10. Auxiliary panel connector (20-pin AUX_PANEL1) 4-15
4-5
4-10
4-13
Internal LEDs Page
1. Standby power LED 4-16
2. CPU warning LED (ERR_CPU1, ERR_CPU2) 4-16
ASUS RS700D-E6/PS8 4-3

4.2 Jumpers

1. Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters
by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1–2 (default) to pins 2–3. Keep the cap
on pins 2–3 for about 5–10 seconds, then move the cap back to pins 1–2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup
to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper
default position. Removing the cap will cause system boot failure!
If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After the CMOS clearance, reinstall the battery.
Chapter 4: Motherboard information4-4
2. VGA controller setting (3-pin VGA_SW1)
This jumper allows you to enable or disable the onboard VGA controller. Set to pins 1–2 to activate the VGA feature.
3. DDR3 voltage control setting (4-pin LVDDR3_SEL1, LVDDR3_SEL2)
These jumpers allow you to adjust the DIMM voltage. Set to pins 1–2 to select 1.5V BIOS control, pins 2–3 to select 1.2V Force or 3–4 to select
1.35V Force.
ASUS RS700D-E6/PS8 4-5
4. LAN controller setting (3-pin LAN_SW1, LAN_SW2)
These jumpers allow you to enable or disable the onboard Intel
®
Intel
82574LGigabit LAN controllers. Set to pins 1-2 to activate the Gigabit LAN
feature.
5. Intel® ICH10R SATA port S/W RAID setting (3-pin RAID_SEL1)
This jumper allows you to select the Serial ATA RAID conguration utility to use when you create disk arrays. Place the jumper caps on pins 1-2 if you
want to use the LSI® MegaRAID software RAID utility (default); otherwise,
place the jumper caps on pins 2-3 to use the Intel® Matrix Storage Manager
(IMSM).
Chapter 4: Motherboard information4-6
6. ForceBIOSrecoverysetting(3-pinRECOVERY1)
This jumper allows you to quickly update or recover the BIOS settings when it
becomes corrupted.
To update the BIOS:
1. Prepare a USB ash disk that contains the original or latest BIOS for the motherboard (XXXXXX.ROM) and the AFUDOS.EXE utility.
2. Set the jumper to pins 2–3.
3. Insert the USB ash and turn on the system to update the BIOS.
4. Shut down the system.
5. Set the jumper back to pins 1-2.
6. Turn on the system.
ASUS RS700D-E6/PS8 4-7

4.3 Internal connectors

1. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Supported by the Intel® ICH10R chipset, these connectors are for the Serial
ATA signal cables for Serial ATA hard disk drives that allows up to 3Gb/s of
data transfer rate.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 10, or RAID 5 conguration.
The actual data transfer rate depends on the speed of Serial ATA hard disks installed.
Chapter 4: Motherboard information4-8
2. USB connector (5-1 pin USB3; A-Type USB4)
These connectors are for USB 2.0 ports. Connect the USB module cables to connectors USB3, then install the modules to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specication that supports up to 480 Mbps connection speed.
ASUS RS700D-E6/PS8 4-9
3. Front fan connectors (4-pin FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4)
The fan connectors support cooling fans of 350 mA–740 mA (8.88 W max.) or a total of 3.15 A–6.66 A (53.28 W max.) at +12V. Connect the fan cables to
the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.
DO NOT forget to connect the fan cables to the fan connectors. Insufcient
air ow inside the system may damage the motherboard components.
These are not jumpers! DO NOT place jumper caps on the fan connectors!
All fans feature the ASUS Smart Fan technology.
Chapter 4: Motherboard information4-10
4. LPC debug card connector (14-1 pin LPC1)
This is a low pin count interface used to plug in the LPC debug card.
5. Serial General Purpose Input/Output connector (6-1 pin SGPIO1)
This connector is used for the SGPIO peripherals for the LSI MegaRAID and
Intel Matrix RAID SATA LED.
ASUS RS700D-E6/PS8 4-11
6. BMC header (BMC_FW1)
The BMC connector on the motherboard supports an ASUS® Server
Management Board 4 Series (ASMB4).
7. Power Supply SMBus connectors (6-1 pin JP1, JP2)
These connectors allow you to connect SMBus (System Management Bus) to
the power supply unit to read PSU information. Devices communicate with an
SMBus host and/or other SMBus devices using the SMBus interface.
Chapter 4: Motherboard information4-12
8. Proprietary power connectors (20-pin PWR1, 20-pin PWR2, 4-pin PWR3)
These connectors are for Proprietary power supply plugs. The power supply
plugs are designed to t these connectors in only one orientation. Orient the connectors and push down rmly until they completely t.
The 4-pin EZ_PLUG is designed for hard disk drives power supply. DO NOT
connect other 4-pin power connectors of the power supply unit (PSU) to this connector.
Connect either one of the 20-pin power connectors to boot up the system.
Use of a PSU with a higher power output is recommended when
conguring a system with more power-consuming devices. The system
may become unstable or may not boot up if the power is inadequate.
USE THE PROPRIETARY POWER SUPPLY ONLY and ensure that your
PSU can provide at least the minimum power required by your system.
ASUS RS700D-E6/PS8 4-13
9. System panel connector (20-pin PANEL1)
This connector supports several chassis-mounted functions.
1. System power LED (3-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
2. Message LED (2-pin MLED)
This 2-pin connector is for the message LED cable that connects to
the front message LED. The message LED is controlled by Hardware monitor to indicate an abnormal event occurance.
3. System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.
4. Hard disk drive activity LED (2-pin HDDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or ashes
when data is read from or written to the HDD.
5. Proprietary power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode
depending on the BIOS settings. Pressing the power switch for more
than four seconds while the system is ON turns the system OFF.
6. Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
Chapter 4: Motherboard information4-14
10. Auxiliary panel connector (20-pin AUX_PANEL1)
This connector is for additional front panel features including front panel
SMB, locator LED and switch, chassis intrusion, and LAN LEDs.
1. Front panel SMB (6-1 pin FPSMB)
These leads connect the front panel SMBus cable.
2. LAN activity LED (2-pin LAN1_LED, LAN2_LED)
These leads are for Gigabit LAN activity LEDs on the front panel.
3. Chassis intrusion (4-1 pin CHASSIS)
These leads are for the intrusion detection feature for chassis with
intrusion sensor or microswitch. When you remove any chassis
component, the sensor triggers and sends a high-level signal to these leads to record a chassis intrusion event. The default setting is short
CASEOPEN and GND pin by jumper cap to disable the function.
4. Locator LED (2-pin LOCATORLED1 and 2-pin LOCATORLED2)
These leads are for the locator LED1 and LED2 on the front panel. Connect the Locator LED cables to these 2-pin connector. The LEDs will
light up when the Locator button is pressed.
5. Locator Button/Swich (2-pin LOCATORBTN)
These leads are for the locator button on the front panel. This button queries the state of the system locator.
ASUS RS700D-E6/PS8 4-15

4.4 Internal LEDs

1. Standby Power LED
The motherboard comes with a standby power LED. The green LED lights up
to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.
2. CPU warning LED (ERR_CPU1, ERR_CPU2)
The CPU warning LEDs light up to indicate that an impending failure of the
corresponding CPU.
Chapter 4: Motherboard information4-16
Chapter 5
This chapter tells how to change the
system settings through the BIOS Setup menus. Detailed descriptions of the BIOS
parameters are also provided.
ASUS RS700D-E6/PS8
BIOS setup

5.1 Managing and updating your BIOS

The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup:
1.
AFUDOS utility
ash drive.)
2.
ASUS CrashFree BIOS 3
when the BIOS le fails or gets corrupted.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS le to a bootable USB ash drive in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the AFUDOS utility.

5.1.1 AFUDOS utility

The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable USB ash drive with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets
corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS le using the AFUDOS utility:
Ensure that the USB ash drive is not write-protected and has at least 2048
The succeeding BIOS screens are for reference only. The actual BIOS
(Updates the BIOS in DOS mode using a bootable USB
(To recover the BIOS using a USB ash drive
KB free space to save the le.
screen displays may not be the same as shown.
1. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable USB ash drive.
2. Boot the system in DOS mode, and then at the prompt type:
afudos /o[lename]
where the [lename] is any user-assigned lename not more than eight alphanumeric characters for the main lename and three alphanumeric
characters for the extension name.
A:\>afudos /oOLDBIOS1.rom
Mainlename Extension name
3. Press <Enter>. The utility copies the current BIOS le to the USB ash drive.
A:\>afudos /oOLDBIOS1.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading ash ..... done
Write to le...... ok
A:\>
The utility returns to the DOS prompt after copying the current BIOS le.
5-2 Chapter 5: BIOS setup
UpdatingtheBIOSle
To update the BIOS le using the AFUDOS utility:
1. Visit the ASUS website (www.asus.com) and download the latest BIOS le for the motherboard. Save the BIOS le to a bootable USB ash drive.
Write the BIOS lename on a piece of paper. You need to type the exact BIOS lename at the DOS prompt.
2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable USB ash drive.
3. Boot the system in DOS mode, and then at the prompt type:
afudos /i[lename]
where [lename] is the latest or the original BIOS le on the bootable USB ash drive, and then press <Enter>.
A:\>afudos /iRS700DE6.ROM
The utility veries the le, and then starts updating the BIOS le.
A:\>afudos /iRS700DE6.ROM AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during ash BIOS
Reading le ....... done
Reading ash ...... done
Advance Check ......
Erasing ash ...... done
Writing ash ...... 0x0008CC00 (9%)
DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure!
5. The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iRS700DE6.ROM AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during ash BIOS
Reading le ....... done
Reading ash ...... done
Advance Check ......
Erasing ash ...... done
Writing ash ...... done
Verifying ash .... done
Please restart your computer
A:\>
ASUS RS700D-E6/PS8 5-3

5.1.2 ASUS CrashFree BIOS 3 utility

The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS le using the motherboard support DVD or a USB ash drive that contains the BIOS le.
The BIOS le in the motherboard support DVD may be older than the BIOS le published on the ASUS ofcial website. If you want to use the newer BIOS le, download the le at support.asus.com and save it to a USB ash drive.
Recovering the BIOS
To recover the BIOS
1. Turn on the system.
2. Insert the motherboard support DVD to the optical drive, or the USB ash drive containing the BIOS le to the USB port.
3. The utility automatically checks the devices for the BIOS le. When found, the utility reads the BIOS le and starts ashing the corrupted BIOS le.
4. Turn off the system after the utility completes the updating process and power on again.
5. The system requires you to enter BIOS Setup to recover BIOS setting. To
ensure system compatibility and stability, we recommend that you press
<F2> to load default BIOS values.
DO NOT shut down or reset the system while recovering the BIOS! Doing so can cause system boot failure!
5-4 Chapter 5: BIOS setup

5.2 BIOS setup program

This motherboard supports a programmable rmware chip that you can update
using the provided utility described in section
.
BIOS
Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to “Run Setup.” This section explains how to congure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
conguration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to recongure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the rmware chip.
The rmware chip on the motherboard stores the Setup utility. When you start up
the computer, the system provides you with the opportunity to run this program.
Press <Del> during the Power-On Self-Test (POST) to enter the Setup utility;
otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the rst two failed. The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make your selections from the available options using the navigation keys.
5.1 Managing and updating your
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Select the Exit Menu. See section
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
Visit the ASUS website at www.asus.com to download the latest BIOS le
for this motherboard.
ASUS RS700D-E6/PS8 5-5
5.7 Exit Menu
Load Default Settings
.
item under the

5.2.1 BIOS menu screen

Menu bar
Main Advanced Server Boot Exit
System Time [13:44:30] System Date [Thu, 01/08/2009]
SATA 1 : [ST3160812AS] SATA 2 : [Not Detected] SATA 3 : [Not Detected] SATA 4 : [Not Detected]
IDE Conguration AHCI Conguration System Information
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Sub-menu items
CongurationeldsMenu items
BIOS SETUP UTILITY
General help
Use [ENTER], [TAB] or [SHIFT-TAB] to select a eld.
Use [+] or [-] to congure system Date.
←→ Select Screen ↑↓ Select Item
+- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit
Navigation keys

5.2.2 Menu bar

The menu bar on top of the screen has the following main items:
Main For changing the basic system conguration
Advanced For changing the advanced system settings
Server For changing the advanced server settings Boot For changing the system boot conguration
Exit For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.

5.2.3 Navigation keys

At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings.
Some of the navigation keys differ from one screen to another.
5-6 Chapter 5: BIOS setup

5.2.4 Menu items

The highlighted item on the menu bar displays the specic items for that menu; for
example, selecting Main shows the Main menu items.
The other items (Advanced, Power, Boot, and Exit) on the menu bar have their
respective menu items.

5.2.5 Sub-menu items

A solid triangle before each item on any menu screen means that the item has a sub-menu. To display the sub-menu, select the item and press <Enter>.
5.2.6 Congurationelds
These elds show the values for the menu items. If an item is user-congurable, you can change the value of the eld opposite the item. You cannot select an item that is not user-congurable.
A congurable eld is enclosed in brackets, and is highlighted when selected. To change the value of a eld, select it then press <Enter> to display available
options. Refer to 5.2.7 Pop-up window.

5.2.7 Pop-up window

Select a menu item and press <Enter> to display a pop-up window with the
conguration options for that item.

5.2.8 Scroll bar

A scroll bar appears on the right side of
Advanced
CPU Bridge Chipset Conguration
USB Functions [12 USB Ports] USB Port Congure [8X4 USB Ports] USB 2.0 Controller [Enabled] HDA Controller [Enabled] SMBUS Controller [Enabled]
SLP_S4# Min. Assertion Width [1 to 2 seconds]
PCIE Ports Conguration PCIE Port 0 [Auto] PCIE Port 1 [Auto] PCIE Port 2 [Auto] PCIE Port 3 [Auto] PCIE Port 4 [Auto] PCIE Port 5 [Auto] PCIE High Priority Port [Disabled]
a menu screen when there are items that
do not t on the screen. Press the Up/
Down arrow keys or <Page Up> /<Page Down> keys to display the other items on the screen.
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Disabled
2 USB Ports 4 USB Ports 6 USB Ports 8 USB Ports 10 USB Ports 12 USB Ports
Scroll bar
Pop-up window
Options
Disabled 2 USB Ports 4 USB Ports 6 USB Ports 8 USB Ports 10 USB Ports 12 USB Ports
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit

5.2.9 General help

At the top right corner of the menu screen is a brief description of the selected item.
ASUS RS700D-E6/PS8 5-7

5.3 Main menu

When you enter the BIOS Setup program, the Main menu screen appears, giving
you an overview of the basic system information.
Refer to section 5.2.1 BIOS menu screen for information on the menu screen items and how to navigate through them.
Main Advanced Server Boot Exit
System Time [13:44:30] System Date [Thu, 01/08/2009]
SATA 1 : [ST3160812AS] SATA 2 : [Not Detected] SATA 3 : [Not Detected] SATA 4 : [Not Detected]
IDE Conguration AHCI Conguration System Information
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Use [ENTER], [TAB] or [SHIFT-TAB] to select a eld.
Use [+] or [-] to congure system Date.
←→ Select Screen ↑↓ Select Item
+- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit

5.3.1 System Time [xx:xx:xx]

Allows you to set the system time.

5.3.2 System Date [Day xx/xx/xxxx]

Allows you to set the system date.

5.3.3 SATA1–4

The BIOS automatically detects the connected IDE devices. There is a separate
sub-menu for each IDE device. Select a device item, then press <Enter> to display the IDE device information.
Main
SATA 1
Device :Hard Disk Vendor :ST3160812AS Size :160.0GB LBA Mode :Supported Block Mode:16Sectors PIO Mode :4 Async DMA :MultiWord DMA-2 Ultra DMA :Ultra DMA-6 S.M.A.R.T.:Supported
Type [Auto] LBA/Large Mode [Auto] Block(Multi-Sector Transfer)M [Auto] PIO Mode [Auto] DMA Mode [Auto] SMART Monitoring [Auto] 32Bit Data Transfer [Enabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Disabled: Disables LBA Mode. Auto: Enables LBA Mode if the device supports it and the devide is not already formatted with LBA Mode disabled.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
5-8 Chapter 5: BIOS setup
The BIOS automatically detects the values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and S.M.A.R.T. monitoring). These values are not user-congurable. These items show
N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the appropriate IDE device type. Select [CDROM] if you are specically conguring a CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Conguration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA
mode disabled.
Conguration options: [Disabled] [Auto]
Block (Multi-Sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the data
transfer from and to the device occurs multiple sectors at a time if the device
supports multi-sector transfer feature. When set to [Disabled], the data transfer
from and to the device occurs one sector at a time.
Conguration options: [Disabled] [Auto]
PIO Mode [Auto]
Allows you to select the data transfer mode.
Conguration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Sets the DMA mode.
Conguration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] [UDMA6]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Conguration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer. Conguration options: [Disabled] [Enabled]
ASUS RS700D-E6/PS8 5-9
5.3.4 IDEConguration
The items in this menu allow you to set or change the congurations for the IDE
devices installed in the system. Select an item then press <Enter> if you wish to
congure the item.
Main
IDE Conguration
SATA Conguration [Enhanced] Congure SATA as [IDE]
Hard Disk Write Protect [Disabled] IDE Detect Time Out (Sec) [35]
BIOS SETUP UTILITY
Options
Disabled Compatible Enhanced
SATAConguration[Enhanced]
Conguration options: [Disabled] [Compatible] [Enhanced]
Configure SATA as [IDE]
Sets the conguration for the Serial ATA connectors supported by the Southbridge chip. Conguration options: [IDE] [RAID] [AHCI]
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, keep the default setting [IDE].
If you want the Serial ATA hard disk drives to use the Advanced Host
Controller Interface (AHCI), set this item to [AHCI]. The AHCI allows
the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive
to internally optimize the order of commands.
If you want to use LSI® MegaRAID or the Intel® Matrix Storage Technology
conguration from the Serial ATA hard disk drives, set this item to [RAID].
Hard Disk Write Protect [Disabled]
Disables or enables device write protection. This will be effective only if the device
is accessed through BIOS. Conguration option: [Disabled] [Enabled]
IDE Detect Time Out (Sec) [35]
Selects the time out value for detecting ATA/ATAPI devices.
Conguration options: [0] [5] [10] [15] [20] [25] [30] [35]
5-10 Chapter 5: BIOS setup
5.3.5 AHCIConguration
This menu is the section for AHCI conguration.
Main
AHCI Settings
AHCI CD/DVD Boot Time out [35]
SATA Port1 [Not Detected] SATA Port2 [Not Detected] SATA Port3 [Not Detected] SATA Port4 [Not Detected]
AHCI CD/DVD Boot Time out [35]
Selects the boot time out value for SATA CD/DVD devices in AHCI mode.
Congifuration options: [0] [5] [10] [15] [20] [25] [30] [35]
SATA Port1–4 [XXXX]
Displays the status of auto-detection of SATA devices.
Main
SATA Port1
Device :Not Detected
SATA Port0 [Auto] SMART Monitoring [Enabled]
SATA Port0 [Auto]
Allows you to select the type of device connected to the system.
Conguration options: [Auto] [Not Installed]
SMART Monitoring [Enabled]
Allows you to set the Self-Monitoring, Analysis and Reporting Technology.
Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
BIOS SETUP UTILITY
Some SATA CD/DVD in AHCI mode need to wait ready longer.
Select the type of device connected to the system.
ASUS RS700D-E6/PS8 5-11

5.3.6 System Information

This menu gives you an overview of the general system specications. The BIOS
automatically detects the items in this menu.
Main
AMIBIOS
Version :0108 Build Date :12/25/08
Processor
Speed :2400MHZ Count :1
System Memory
Usable Size : 1024MB
System Memory Information
AMIBIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specication.
System Memory
Displays the auto-detected system memory.
System Memory Information
Displays system memory information.
Main
AMIBIOS
CPU1 Memory Conguration CPU2 Memory Conguration
BIOS SETUP UTILITY
BIOS SETUP UTILITY
CPU1/2 Memory Configuration
Allows you to check information of installed memory (6 DIMMs per CPU).
5-12 Chapter 5: BIOS setup

5.4 Advanced menu

The Advanced menu items allow you to change the settings for the CPU and other system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
eld values can cause the system to malfunction.
Main Advanced Server Boot Exit
CPU Conguration Chipset Conguration Legacy Device Conguration USB Conguration PCIPnP Conguration Power On Conguration Event Log Conguration Hardware Monitor PCI Exppress Conguration ACPI Conguration
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
5.4.1 CPUConguration
The items in this menu show the CPU-related information that the BIOS
automatically detects. Some items may not appear if your CPU does not support the related functions.
Advanced
Congure advanced CPU settings
Module Version:3F.11
Manufacturer:Intel Brand String:Genuine Intel(R) CPU @ 0000 @ 2.67GHz Frequency :2.66GHz BCLK Speed :133MHz Cache L1 :128 KB Cache L2 :1024 KB Cache L3 :8192 KB Ratio Status:Unlocked (Min:12, Max:20) Ratio Actual Value :20 CPUID :106A2
Ratio CMOS Setting: [Auto] C1E Support [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetch [Enabled] Intel(R) Virtualization Tech [Enabled] CPU TM Function [Enabled]
Scroll down for more items.
Execute-Disable Bit Capability [Enabled] Intel(R) HT Technology [Enabled] Active Processor Cores [All] A20M [Disabled] DCU Mode [32KB 8-way without] DCA Prefetch Delay [32] Intel(R) SpeedStep(TM) Tech [Enabled] Intel(R) C-STATE Tech [Enabled] C3 State [ACPI C2] C6 State [Enabled] C State package limit setting [Auto] C1 Auto Demotion [Enabled] C3 Auto Demotion [Enabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
BIOS SETUP UTILITY
Congure CPU.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Sets the ratio between CPU Core Clock and the FSB Frequency. Note:If an invalid ratio is set in CMOS then actual and setpoint values may differ.
←→ Select Screen ↑↓ Select Item
F1 General Help F10 Save and Exit ESC Exit
ASUS RS700D-E6/PS8 5-13
Ratio CMOS Setting [Auto]
Allows you to adjust the ratio between CPU Core Clock and BCLK Frequency.
Use the <+> and <-> keys to adjust the value.
Conguration options: [Auto] [12.0] [13.0] [14.0] [15.0] [16.0] [17.0] [18.0] [19.0] [20.0]
C1E Support [Enabled]
Allows you to enable or disable Enhanced Halt State support.
Conguration options: [Disabled] [Enabled]
Hardware Prefetcher [Enabled]
Allows you to enable or disable the Hardware Prefetcher function.
Conguration options: [Disabled] [Enabled]
AdjacentCacheLinePrefetch[Enabled]
Allows you to enable or disable the Adjacent Cache Line Prefetch function.
Conguration options: [Disabled] [Enabled]
Intel(R) Virtualization Tech [Enabled]
The Intel® Virtualization Technology allows a hardware platform to run multiple operating systems separately and simultaneously, enabling one system to virtually function as several systems.
Conguration options: [Disabled] [Enabled]
CPU TM Function [Enabled]
This function enables the overheated CPU to throttle the clock speed to cool down.
Conguration options: [Disabled] [Enabled]
Execute-Disable Bit Capability [Enabled]
Allows you to enable or disable the No-Execution Page Protection Technology.
Setting this item to [Disabled] forces the XD feature ag to always return to zero (0). Conguration options: [Disabled] [Enabled]
Intel(R) HT Technology [Enabled]
Allows you to enable or disable the Intel Hyper-Threading Technology function.
When disabled, only one thread per activated core is enabled. Conguration options: [Enabled] [Disabled]
Active Processor Cores [All]
Allows you to choose the number of CPU cores to activate in each processor package.
Conguration options: [All] [1] [2]
5-14 Chapter 5: BIOS setup
A20M [Disabled]
Legacy OSes and APs may need A20M enabled. Conguration options: [Disabled] [Enabled]
DCU Mode [32KB 8-way without]
Allows you to select the mode for the Data Cache.
Conguration options: [32KB 8-way without ECC] [16KB 4-way with ECC]
DCA Prefetch Delay [32]
Allows you to select the time delay in bus clocks from snoop to prefetch.
Conguration options: [8] [16] [24] [32] [40]—[104] [112] [120]
Intel(R) SpeedStep (TM) Tech [Enabled]
When set to [Disabled], the CPU runs at its default speed. When set to [Enabled],
the CPU speed is controlled by the operating system.
Conguration options: [Disabled] [Enabled]
Intel(R) C-STATE Tech [Enabled]
The Intel® C-State Technology allows the CPU to save more power under idle mode. Enable this item only when you install a C-State Technology-supported CPU.
Conguration options: [Disabled] [Enabled]
C3 State [ACPI C2]
Allows you to select the CPU action under C3 state.
Conguration options: [Disabled] [ACPI C2] [ACPI C3]
C6 State [Enabled]
Allows you to select the CPU action under C6 state.
Conguration options: [Disabled] [Enabled]
C State package limit setting [Auto]
This item appears only when you set the Intel(R) C-STATE Tech item to [Enabled]. We recommend that you set this item to [Auto] for BIOS to automatically detect the
C-State mode supported by your CPU.
Conguration options: [Auto] [C1] [C3] [C6] [C7]
C1 Auto Demotion [Enabled]
When enabled, CPU will conditionally demote C3/C6/C7 requests to C1 based on
on-core auto-demote information.
Conguration options: [Disabled] [Enabled]
ASUS RS700D-E6/PS8 5-15
C3 Auto Demotion [Enabled]
When enabled, CPU will conditionally demote C6/C7 requests to C3 based on on-
core auto-demote information.
Conguration options: [Disabled] [Enabled]
5.4.2 ChipsetConguration
The Chipset conguration menu allows you to change advanced chipset settings.
Select an item then press <Enter> to display the sub-menu.
Advanced
Advanced Chipset Settings
WARNING: Setting wrong values in below sections may cause system to malfunction.
CPU Bridge Conguration North Bridge Conguration South Bridge Conguration Intel VT-d Conguration
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Congure North Bridge features.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
CPUBridgeChipsetConguration
Advanced
CPU Bridge Chipset Conguration
CPU Revision :B0 Current CSI Frequency :4.800GT Current Memory Frequency :1066 Mhz
CSI Links Speed [Full-Speed] CSI Frequency [Auto] CSI Isochronous [Disabled] CSI L0s [Disabled] CSI L1 [Disabled]
Memory Frequency [Auto] Memory Mode [Independent] Memory ECC Function [Enabled] Double Rate Refresh [Auto] Demand Scrubbing [Enabled] Patrol Scrubbing [Disabled] NUMA Aware [Auto] Page Policy [Closed]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Scroll down for more items.
Adaptive Page [Disabled] Data Scramble [Enabled] Split Below 4GB [Disabled] Channel Interleaving [6:1] Rank Interleaving [4:1]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
To transition the CSI links to full-speed or leave them in slow-mode.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
5-16 Chapter 5: BIOS setup
CSI Links Speed [Full-Speed]
Allows you to set the speed of CSI Links.
Conguration options: [Slow-Mode] [Full-Speed]
CSI Frequency [Auto]
Allows you to set the CSI frequency.
Conguration options: [Auto] [4.800GT] [5.866GT] [6.400GT]
CSI Isochronous [Disabled]
Conguration options: [Disabled] [Enabled]
CSI L0s [Disabled]
Conguration options: [Disabled] [Enabled]
CSI L1 [Disabled]
Conguration options: [Disabled] [Enabled]
Memory Frequency [Auto]
You may allow the system to detect DDR3 memory frequency via SPD or designate a specic frequency. Conguration options: [Auto] [Force DDR-800] [Force DDR-1066] [Force DDR-1333]
Memory Mode [Independent]
Allows you to set Memory channel mode.
Conguration options: [Independent] [Channel Mirroring] [Lockstep] [Sparing]
Memory ECC Function [Enabled]
Allows you to enable or disable Memory ECC fucntion.
Conguration options: [Disabled] [Enabled]
Double Rate Refresh [Auto]
Conguration options: [Disabled] [Auto]
Demand Scrubbing [Enabled]
Enables or disables the ECC demand scrub.
Conguration options: [Disabled] [Enabled]
Patrol Scrubbing [Disabled]
Enables or disables the ECC patrol scrub.
Conguration options: [Disabled] [Enabled]
ASUS RS700D-E6/PS8 5-17
NUMA Aware [Auto]
Conguration options: [Disabled] [Enabled]
Page Poilcy [Closed]
Conguration options: [Closed] [Open]
Adaptive Page [Disabled]
Conguration options: [Disabled] [Enabled]
Data Scramble [Disabled]
Conguration options: [Disabled] [Enabled]
Split Below 4 GB [Disabled]
Conguation options: [Disabled] [Auto]
Channel Interleaving [6:1]
Allows you to set the channel interleaving setting.
Conguation options: [1:1] [2:1] [4:1] [6:1]
Rank Interleaving [4:1]
Allows you to set the rank interleaving setting.
Conguation options: [1:1] [2:1] [4:1]
NorthBridgeChipsetConguration
Advanced
NorthBridge Chipset Conguration
NB Revision :B3 Current CSI Frequency :4.800GT
Crystal Beach / DMA [Disabled]
BIOS SETUP UTILITY
Crystal Beach / DMA [Disabled]
Conguation options: [Disabled] [Auto]
5-18 Chapter 5: BIOS setup
SouthBridgeChipsetConguration
Advanced
CPU Bridge Chipset Conguration
USB Functions [4 USB Ports] USB Port Congure [8+4 USB Ports]
USB 2.0 Controller [Enabled]
HDA Controller [Enabled]
SLP_S4# Min. Assertion Width [1 to 2 seconds]
USB Functions [4 USB Ports]
Allows you to congure the amount of USB ports to be enabled. Conguration options: [Disabled] [2 USB Ports] [3 USB Ports] [4 USB Ports]
USBPortCongure[8+4USBPorts]
This item disappears when you set the
Conguration options: [6+6 USB Ports] [8+4 USB Ports]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller. This item become uncongurable if you set the [12 USB Ports]. Conguration options: [Enabled] [Disabled]
HDA Controller [Enabled]
Allows you to enable or disable the High Denition Audio controller. Conguration options: [Enabled] [Disabled]
BIOS SETUP UTILITY
USB Functions
USB Functions
Options
Disabled 2 USB Ports 3 USB Ports 4 USB Ports
item to [Disabled].
item to [10 USB Ports] or
SLP_S4# Min. Assertion Width [1 to 2 seconds]
Conguration options: [4 to 5 seconds] [3 to 4 seconds] [2 to 3 seconds] [1 to 2 seconds]
ASUS RS700D-E6/PS8 5-19
IntelVT-dConguration
Advanced
Intel VT-d [Disabled]
Intel VT-d [Disabled]
Allows you to enable or disable the Intel Virtualization Technology for
Directed I/O.
Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Disabled Enabled
5.4.3 LegacyDeviceConguration
Advanced
Legacy Device Conguration
Serial Port1 Address [3F8/IRQ4] Serial Port2 Address [2F8/IRQ3]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Allows BIOS to Select Serial Port1 Base Address.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
Options
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Conguration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]
Serial Port2 Address [2F8/IRQ3]
Allows you to select the Serial Port2 base address. Conguration options: [Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]
5-20 Chapter 5: BIOS setup
5.4.4 USBConguration
Advanced
USB Conguration
Module Version - 2.24.3-13.4
USB Devices Enabled :
None
Legacy USB Support [Enabled] USB 2.0 Controller Mode [HiSpeed] BIOS EHCI Hand-Off [Enabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
The following item appears only when you set USB Function to [Enabled].
Legacy USB Support [Enabled]
Allows you to enable or disable support for legacy USB devices. Setting to [Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Conguration options: [Disabled] [Enabled] [Auto]
The following item appears only when you set USB Function to [Enabled].
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller to HiSpeed (480Mbps) or FullSpeed (12Mbps). Conguration options: [FullSpeed] [HiSpeed]
BIOS SETUP UTILITY
Enables support for legacy USB. AUTO option disables legacy support if no USB devices are connected.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
BIOS EHCI Hand-Off [Enabled]
Enables or disables the BIOS EHCI hand-off support. Conguration options: [Disabled] [Enabled]
ASUS RS700D-E6/PS8 5-21
5.4.5 PCIPnPConguration
The PCIPnP Conguration menu items allow you to change the advanced settings
for PCI/PnP devices.
Take caution when changing the settings of the PCI/PnP Conguration menu items. Incorrect eld values can cause the system to malfunction.
Advanced
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections may cause system to malfunction.
Plug And Play O/S [No]
PCI Option ROM Scan Order [Bus 0 First] Onboard Option ROM Priority [High]
Onboard LAN1 Boot [PXE] Onboard LAN2 Boot [PXE]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
NO: lets the BIOS congure all the devices in the system. YES: lets the operating system congure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
Plug And Play O/S [No]
When set to [No], BIOS congures all the devices in the system. When set to [Yes] and if you install a Plug and Play operating system, the operating system congures the Plug and Play devices not required for boot. Conguration options: [No] [Yes]
PCI Option ROM Scan Order [Bus 0 First]
Allows you to select the PCI option ROM scanning order. The scanning of the option ROM will start from the lowest bus, device, fucntion number if you set this
item to [Bus 0 First]; the scanning starts from the highest bus, device, function number if you set this item to [Bus N First]. Conguration options: [Bus 0 First] [Bus N First]
Onboard Option ROM Priority [High]
Allows you to select the onboard option ROM priority.
Conguration options: [Normal] [High]
Onboard LAN1/2 Boot [PXE]
Allows you to congure the onboard LAN1/2 boot mode. Conguration: [Disabled] [PXE] [iSCSI]
5-22 Chapter 5: BIOS setup
5.4.6 PowerOnconguration
Advanced
APM Conguration
Restore on AC Power Loss [Last State]
Resume On Ring [Disabled] Resume On PME#(Wake On LAN) [Disabled] Resume On RTC Alarm [Disabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Restore on AC Power Loss [Last State]
When set to [Power Off], the system goes into off state after an AC power loss. When set to [Power On], the system will reboot after an AC power loss. When set to [Last State], the system goes into either off or on state, whatever the system
state was before the AC power loss.
Conguration options: [Power Off] [Power On] [Last State]
Resume On Ring [Disabled]
When set to [Enabled], the system enables RI to generate a wake event while the computer is in Soft-off mode. Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Options
Power Off Power On Last State
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
Resume On PME#(Wake On LAN) [Disabled]
When set to [Enabled], the system enables PME to generate a wake event while the computer is in Soft-off mode. Conguration options: [Disabled] [Enabled]
Resume On RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake-up event.
Conguration options: [Disabled] [Enabled]
The following items appear only when the
Resume On RTC Alarm
to [Enabled].
RTC Alarm Date [15]
To set the alarm date, highlight this item and press the <+> or <-> key to make the selection.
System Time [12:30:30]
Use the <ENTER>, <TAB> or <SHIFT-TAB> key to select a eld. Use the <+> or <-> key to congure alarm time.
ASUS RS700D-E6/PS8 5-23
item is set
5.4.7 EventLogConguration
Advanced
Event Logging details
View Event Log Mark all events as read Clear Event Log
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
View Event Log
Press the <ENTER> key to view unread system event log.
Make all events as read
Press the <ENTER> key to mark all events as read. Select [Ok] to conrm the
change.
Clear Event Log
Press the <ENTER> key to clear all system events. Select [Ok] to conrm the
change.
BIOS SETUP UTILITY
View all unread events on the Event log.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
5-24 Chapter 5: BIOS setup

5.4.8 Hardware Monitor

Advanced
Hardware Monitor
CPU1 Temperature [ 27.5ºC/ 81.5ºF] CPU2 Temperature [ 0 ºC/ 32 ºF] Front Fan1 Speed [5357RPM ] Front Fan2 Speed [ N/A ] Front Fan3 Speed [ N/A ] Front Fan4 Speed [ N/A ] Fan Speed Control [High Density Mode] VCORE1 Voltage [ 1.052 V]
VCORE2 Voltage [ N/A ]
+1.5V_P1DDR3 Voltage [ 1.508 V]
+1.5V_P2DDR3 Voltage [ N/A ]
+1.5V_ICH Voltage [ 1.520 V] P1VTT Voltage [ 1.022 V] P2VTT Voltage [ 1.022 V] +1.1V_IOH Voltage [ 0.204 V] +12V Voltage [12.000 V] +5V Voltage [ 5.196 V] +3.3V Voltage [ 3.246 V]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Options
Disabled Enabled
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
Scroll down for more items.
+5VSB Voltage [ 5.132 V] +3VSB Voltage [ 3.198 V] VBAT Voltage [ 3.126 V]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
CPU1/2 Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU
temperatures. Select [Ignored] if you do not wish to display the detected
temperatures.
Front Fan1–4 Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the speed of CPU fans, front fans, and rear fans in rotations per minute (RPM). If the fan is not
connected to the motherboard, the eld shows [N/A].
Fan Speed Control [High Density Mode]
Allows you to congure the ASUS Smart Fan feature that smartly adjusts the fan speeds for more efcient system operation. Conguration options: [Full Speed Mode] [Whisper Mode] [Generic Mode] [High Density Mode]
VCORE1/2Voltage,+1.5V_P1/2DDR3Voltage,+1.5V_ICHVoltage, P1/2VTT Voltage, +1.1V_IOHVoltage,+12VVoltage,+5VVoltage, +3.3VVoltage,+5VSBVoltage,+3VSBVoltage,VBATVoltage
The onboard hardware monitor automatically detects the voltage output through
the onboard voltage regulators. Select [Ignored] if you do not want to detect this
item.
ASUS RS700D-E6/PS8 5-25
5.4.9 PCIExpressConguration
Advanced
PCI Express Conguration
Active State Power-Management [Disabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Active State Power-Management [Disabled]
Enables or disables the PCI Express L0s and L1 link power states. Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Enable/Disable PCI Express L0s and L1 link power states.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
5-26 Chapter 5: BIOS setup
5.4.10 ACPIConguration
Advanced
ACPI Settings
Advanced ACPI Conguration Chipset ACPI Conguration General WHEA Conguration
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
BIOS SETUP UTILITY
Advanced ACPI Conguration settings.
Use this section to congure additional ACPI options.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
AdvancedACPIConguration
Advanced
Advanced ACPI Conguration
ACPI 2.0 Support [Enabled] ACPI APIC support [Enabled] BIOS-->AML ACPI table [Enabled] Headless mode [Disabled]
ACPI 2.0 Support [Enabled]
Species the Advanced Conguration and Power Interface (ACPI) version
supported.
Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Add additional tables as per ACPI 2.0 specications.
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Conguration and Power Interface (ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When
set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list.
Conguration options: [Disabled] [Enabled]
BIOS-->AML ACPI table [Enabled]
Allows you to include the BIOS-->AML exchange table pointer to (X)RSDT pointer
list.
Conguration options: [Disabled] [Enabled]
Headless mode [Disabled]
Allows you to enable or disable the Headless operation mode through ACPI.
Conguration options: [Disabled] [Enabled]
ASUS RS700D-E6/PS8 5-27
ChipsetACPIConguration
Advanced
South Bridge ACPI Conguration
Energy Lake Feature [Disabled] APIC ACPI SCI IRQ [Disabled] USB Device Wakeup From S3/S4 [Disabled] High Performance Event Timer [Disabled]
Energy Lake Feature [Disabled]
Allows you to enable or disable the Energy Lake feature.
Conguration options: [Enabled] [Disabled]
APIC ACPI SCI IRQ [Disabled]
Allows you to enable or disable the APIC ACPI SCI IRQ feature.
Conguration options: [Disabled] [Enabled]
USB Device Wakeup From S3/S4 [Disabled]
Allows you to enable or disable the USB device wakeup from S3/S4 feature. Conguration options: [Disabled] [Enabled]
High Performance Event Timer [Disabled]
Allows you to enable or disable the High Performance Event Timer feature.
Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Enabled Disabled
Options
GeneralWHEAConguration
Advanced
General WHEA Conguration
WHEA Support [Enabled]
BIOS SETUP UTILITY
Enable or disable Windows Hardware Error Architecture.
WHEA Support [Enabled]
Allows you to enable or disable the Windows Hardware Error Architecture (WHEA)
support.
Conguration options: [Disabled] [Enabled]
5-28 Chapter 5: BIOS setup

5.5 Server menu

The Server menu items allow you to customize the server features.
Main Advanced Server Boot Exit
Remote Access Conguration
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
5.5.1 RemoteAccessConguration
The items in this menu allows you to congure the Remote Access features. Select an item then press <Enter> to display the conguration options.
Server
Congure Remote Access type and parameters
Remote Access [Enabled]
Serial port number [COM2]
Base Address, IRQ [2F8h, 3]
Serial Port Mode [57600 8,n,1] Flow Control [Hardware] Redirection After BIOS POST [Disabled] Terminal Type [VT-UTF8]
BIOS SETUP UTILITY
BIOS SETUP UTILITY
IPMI conguration including server monitoring and event log.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Select Remote Access type.
Remote Access [Enabled]
Enables or disables the remote access feature.
Conguration options: [Disabled] [Enabled]
The following items appear only when
Remote Access
is set to [Enabled].
Serial port number [COM2]
Selects the serial port for console redirection.
Conguration options: [COM1] [COM2]
Base Address. IRQ [2F8h, 3]
This item is not user-congurable and changes with the conguration of Serial
port number.
ASUS RS700D-E6/PS8 5-29
Serial port Mode [57600 8,n,1]
Sets the Serial port mode.
Conguration options: [115200 8,n,1] [57600 8,n,1] [38400 8,n,1] [19200 8,n,1] [09600 8,n,1]
Flow Control [Hardware]
Allows you to select the ow control for console redirection. Conguration options: [None] [Hardware] [Software]
Redirection After BIOS POST [Disabled]
Sets the redirection mode after the BIOS Power-On Self-Test (POST). Some operating system may not work when set to [Always]. Conguration options: [Disabled] [Boot Loader] [Always]
Terminal Type [VT-UTF8]
Allows you to select the target terminal type.
Conguration options: [ANSI] [VT100] [VT-UTF8]
VT-UTF8 Combo Key Support [Enabled]
This item appears only when you set the and allows you to enable or disable the VT-UTF8 combo key support for ANSI or
VT100 terminals. Conguration options: [Disabled] [Enabled]
Terminal Type
item to [ANSI] or [VT100]
5-30 Chapter 5: BIOS setup

5.6 Boot menu

The Boot menu items allow you to change the system boot options. Select an item
then press <Enter> to display the sub-menu.
Main Advanced Server Boot Exit
Boot Settings
Boot Device Priority
Boot Settings Conguration Security
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.

5.6.1 Boot Device Priority

Boot
Boot Device Priority
1st Boot Device [Removable Dev.] 2nd Boot Device [ATAPI CD-ROM] 3rd Boot Device [Hard Drive] 4th Boot Device [Network:IBA GE Slo] 5th Boot Device [Network:IBA GE Slo]
BIOS SETUP UTILITY
BIOS SETUP UTILITY
Species the Boot Device Priority sequence.
A virtual oppy disk drive (Floppy Drive B: ) may appear when you set the CD-ROM drive as the rst boot device.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Species the Boot Device Priority sequence.
A device enclosed in parenthesis has been disabled in the corresponding type menu.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
1st ~ xxth Boot Device [XXXXXXX]
These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.
Conguration options: [xxxxx Drive] [Disabled]
ASUS RS700D-E6/PS8 5-31
5.6.2 BootSettingsConguration
Boot
Boot Settings Conguration
Quick Boot [Enabled] Full Screen Logo [Disabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] Wait For ‘F1‘ If Error [Enabled] Hit ‘DEL‘ Message Display [Enabled] Interrupt 19 Capture [Enabled]
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. Conguration options: [Disabled] [Enabled]
Full Screen Logo [Disabled]
Allows you to enable or disable the full screen logo display feature.
Conguration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
BIOS SETUP UTILITY
Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
←→ Select Screen ↑↓ Select Item
+- Change Option F1 General Help F10 Save and Exit ESC Exit
AddOn ROM Display Mode [Force BIOS]
Allows you to set the display mode for Options ROM.
Conguration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Conguration options: [Off] [On]
Wait For ‘F1‘ If Error [Enabled]
When set to [Enabled], the system waits for the <F1> key to be pressed when error occurs. Conguration options: [Disabled] [Enabled]
Hit ‘DEL‘ Message Display [Enabled]
When set to [Enabled], the system displays the message “Press DEL to run Setup” during POST. Conguration options: [Disabled] [Enabled]
Interrupt 19 Capture [Enabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Conguration options: [Disabled] [Enabled]
5-32 Chapter 5: BIOS setup

5.6.3 Security

The Security menu items allow you to change the system security settings. Select
an item then press <Enter> to display the conguration options.
Boot
Security Settings
Supervisor Password : Not Installed User Password : Not Installed
Change Supervisor Password Change User Password
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a Supervisor Password:
1. Select the Change Supervisor Password item and press <Enter>.
2. From the password box, type a password composed of at least six letters
and/or numbers, then press <Enter>.
3. Conrm the password when prompted.
The message “Password Installed” appears after you successfully set your password.
To change the supervisor password, follow the same steps as in setting a user password.
To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.
BIOS SETUP UTILITY
<Enter> to change password. <Enter> again to disable password.
←→ Select Screen ↑↓ Select Item
Enter Change F1 General Help F10 Save and Exit ESC Exit
If you forget your BIOS password, you can clear it by erasing the CMOS Real
Time Clock (RTC) RAM. See section 4.2 Jumpers for information on how to erase the RTC RAM.
ASUS RS700D-E6/PS8 5-33
After you have set a supervisor password, the other items appear to allow you to change other security settings.
Main Advanced Server Power Boot Tools Exit
Supervisor Password : Installed User Password : Not Installed
Change Supervisor Password User Access Level [Full Access] Change User Password Password Check [Setup]
BIOS SETUP UTILITY
<Enter> to change password. <Enter> again to disable password.
User Access Level [Full Access]
This item allows you to select the access restriction to the Setup items.
Conguration options: [No Access] [View Only] [Limited] [Full Access]
No Access prevents user access to the Setup utility. View Only allows access but does not allow change to any eld. Limited allows changes only to selected elds, such as Date and Time. Full Access allows viewing and changing all the elds in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.
To set a User Password:
1. Select the Change User Password item and press <Enter>.
2. On the password box that appears, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3. Conrm the password when prompted.
The message “Password Installed” appears after you set your password successfully.
To change the user password, follow the same steps as in setting a user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Conguration options: [Setup] [Always]
5-34 Chapter 5: BIOS setup

5.7 Exit menu

The Exit menu items allow you to load the optimal or failsafe default values for the
BIOS items, and save or discard your changes to the BIOS items.
Main Advanced Server Boot Exit
Exit Options
Exit & Save Changes Exit & Discard Changes Discard Changes
Load Setup Defaults
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Pressing <Esc> does not immediately exit this menu. Select one of the options
from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are nished making your selections, choose this option from the Exit
menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned
off. When you select this option, a conrmation window appears. Select
save changes and exit.
BIOS SETUP UTILITY
Exit system setup after saving the changes.
F10 key can be used for this operation.
←→ Select Screen ↑↓ Select Item
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
to
YES
If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Press <Enter> to save the changes while exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you made to the
Setup program. If you made changes to elds other than System Date, System Time, and Password, the BIOS asks for a conrmation before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a conrmation appears. Select
to discard any changes and load the previously saved values.
YES
Load Setup Defaults
This option allows you to load the default values for each of the parameters on the
Setup menus. When you select this option or if you press <F5>, a conrmation
window appears. Select or make other changes before saving the values to the non-volatile RAM.
ASUS RS700D-E6/PS8 5-35
to load default values. Select
YES
Exit & Save Changes
5-36 Chapter 5: BIOS setup
Chapter 6
This chapter provides instructions for
setting up, creating and conguring RAID
sets using the available utilities.
ASUS RS700D-E6/PS8
RAIDconguration

6.1 Setting up RAID

The motherboard comes with the Intel® ICH10R southbridge controller that supports the following SATA RAID solutions:
LSIMegaRAIDsoftwareRAIDCongurationUtility
RAID 1, and RAID 10 support (for both Linux and Windows OS).
Intel Matrix Storage Manager
support (for Windows OS only).
with RAID 0, RAID 1, RAID 10, and RAID 5
(default) with RAID 0,
6.1.1 RAIDdenitions
(Data striping)
RAID 0
data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. Use of two new identical hard disk drives is required for this setup.
(Data mirroring)
RAID 1
drive to a second drive. If one drive fails, the disk array management software directs all applications to the surviving drive as it contains a complete copy of
the data in the other drive. This RAID conguration provides data protection and
increases fault tolerance to the entire system. Use two new drives or use an existing drive and a new drive for this setup. The new drive must be of the same
size or larger than the existing drive.
RAID 10
data) having to be calculated and written. With the RAID 10 conguration you get all the benets of both RAID 0 and RAID 1 congurations. Use four new hard disk
drives or use an existing drive and three new drives for this setup.
RAID 5
drives. Among the advantages of RAID 5 conguration include better HDD performance, fault tolerance, and higher storage capacity. The RAID 5 conguration
is best suited for transaction processing, relational database applications, enterprise resource planning, and other business systems. Use a minimum of three identical hard disk drives for this setup.
is data striping and data mirroring combined without parity (redundancy
stripes both data and parity information across three or more hard disk
optimizes two identical hard disk drives to read and write
copies and maintains an identical image of data from one

6.1.2 Installing hard disk drives

The motherboard supports SATA hard disk drives for RAID set conguration. For
optimal performance, install identical drives of the same model and capacity when creating a disk array.
See section
6-2 Chapter 6: RAID conguration
2.3 Hard disk drives
for SATA hard disk drive installation.

6.1.3 RAID controller selection

You can choose either the LSI Software RAID Conguration Utility or the Intel
Matrix Storage Manager as the default utility to create RAID set(s). See
ICH10R SATA port S/W RAID setting
on page 4-6 for details.
5. Intel®

6.1.4 Setting the RAID item in BIOS

You must enable the RAID function in the BIOS Setup before creating RAID set(s)
using SATA HDDs. To do this:
1. Enter the BIOS Setup during POST.
2. Go to the
3. Set the
4. Save your changes, and then exit the BIOS Setup.
Refer to Chapter 5 for details on entering and navigating through the BIOS
Setup.
menu >
Main
CongureSATAas
IDEConguration
, and then press <Enter>.
item to [RAID].
ASUS RS700D-E6/PS8 6-3
6.2 LSISoftwareRAIDConguration
Utility
The LSI MegaRAID software RAID conguration utility allows you to create RAID 0, RAID 1, or RAID 10 set(s) from SATA hard disk drives connected to the SATA
connectors supported by the motherboard southbridge chip.
To enter the LSI MegaRAID software RAID conguration utility
1. Turn on the system after installing all the SATA hard disk drives.
2. During POST, the LSI MegaRAID software RAID conguration utility
automatically detects the installed SATA hard disk drives and displays any existing RAID set(s). Press <Ctrl> + <M> to enter the utility.
LSI MegaRAID Software RAID BIOS Version A.08 09161344R LSI SATA RAID Found at PCI Bus No: Dev No:1F Device present at Port 0 ST3160812AS 152114MB Device present at Port 1 ST3160812AS 152114MB Device present at Port 2 ST3160812AS 152114MB Device present at Port 3 ST3160812AS 152114MB Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.
The LSI MegaRAID software RAID conguration utility automatically congures to RAID 1 when the SATA to RAID Mode is enabled.
The RAID setup screens shown in this section are for reference only and may not exactly match the items on your screen due to the controller version difference.
When you create RAID sets with the LSI MegaRAID software RAID conguration utility, the boot priority of the SATA optical drive has to be
manually adjusted. Otherwise, the system will not boot from the connected SATA ODD.
3. The utility main window appears. Use the arrow keys to select an option from the
Management Menu
and then press <Enter>. Refer to the Management
Menu descriptions on the next page.
At the bottom of the screen is the legend box. The keys on the legend box
allow you to navigate through the setup menu options or execute commands. The keys on the legend box vary according to the menu level.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
6-4 Chapter 6: RAID conguration
BIOS Version A.08.09161344R
Congure VD(s)
Menu Description
Congure
Allows you to create RAID 0, RAID 1 or RAID 10 set using the Easy Conguration or the New Conguration command. This menu also allows you to view, add, or clear RAID congurations or select the
boot drive
Initialize
Objects
Allows you to initialize the virtual drives of a created RAID set Allows you to initialize virtual drives or change the virtual drive
parameters
Rebuild
Check Consistency
Allows you to rebuild failed drives
Allows you to check the data consistency of the virtual drives of a created RAID set

6.2.1 Creating a RAID set

The LSI Software RAID Conguration Utility allows you to create a RAID 0, RAID 1, or RAID 10 set using two types of congurations:
In
EasyConguration
In
NewConguration
, the virtual drive parameters are set automatically.
, you manually set the virtual drive parameters.
UsingEasyConguration
To create a RAID set using the
EasyConguration
Easy
option
and
New
.
1. From the
Management Menu
, select
Congure>EasyConguration
, and
then press <Enter>.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Denes Physical Arrays. An Array Will Automatically Become A VD
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
ASUS RS700D-E6/PS8 6-5
BIOS Version A.08.09161344R
Conguration Menu
Easy Conguration
New Conguration View/Add Conguration Clear Conguration Select Boot Drive
2. The
ARRAYSELECTIONMENU
displays the available drives connected to
the SATA ports. Use the up/down arrow key to select the drives you want to
include in the RAID set, and then press <Space>. When selected, the drive
indicator changes from
READY
to
ONLINA[X]-[Y]
, where X is the array
number, and Y is the drive number.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Port # 1 DISK 77247MB HDS728080PLA380 PF20A60A
SPACE-Sel,ENTER-EndArray,F10-Congure,F2-Drive Info,F3-Virtual Drives,F4-HSP
The information of the selected hard disk drive displays at the bottom of the screen.
You need at least two identical hard disk drives when creating a RAID 1 set.
You need at least four identical hard disk drives when creating a RAID 10
set.
BIOS Version A.08.09161344R
Easy Conguration - ARRAY SELECTION MENU
PORT #
0
ONLIN A00-00
1
ONLIN A00-01
2
READY
READY
3
3. Select all the drives required for the RAID set, and then press <F10> to congure array setting.
4. Press <Space> to select the congurable array.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
BIOS Version A.08.09161344R
Easy Conguration - ARRAY SELECTION MENU
SPAN-1
Select Congurable Array(s)
A-0
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Congure Esc-Quit
6-6 Chapter 6: RAID conguration
5. Press <F10> again, the virtual drive information appears including a
menu that allows you to change the virtual drive parameters.
Drive
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Congure Esc-Quit
BIOS Version A.08.09161344R
Virtual Drive(s) Congured
Easy Conguration - ARRAY SELECTION MENU
Virgual Drive 0
RAID = 1
Size = 77247MB DWC = Off
RA = On Accept
SPAN = NO
Choose RAID Level For This VD
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
Virtual
6. Select
RAID
7. Select the
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Congure Esc-Quit
from the
RAID
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
Virtual Drive
level from the menu, and then press <Enter>.
BIOS Version A.08.09161344R
Virtual Drive(s) Congured
Easy Conguration - ARRAY SELECTION MENU
Virtual Drive 0
RAID = 1
Size = 77247MB DWC = Off
RA = On Accept
SPAN = NO
Choose RAID Level For This VD
sub-menu, and then press <Enter>.
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
RAID Level
RAID 0
RAID 1
ASUS RS700D-E6/PS8 6-7
8. When creating a
menu, and then press <Enter>.
Drive
When creating a
RAID 1
RAID 0
9. Select On to enable the
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Congure Esc-Quit
Enabling DWC can improve the performance, but with the risk of data loss.
BIOS Version A.08.09161344R
Easy Conguration - ARRAY SELECTION MENU
Virtual Drive 0
RAID = 1
Size = 77247MB DWC = Off
RA = On Accept
SPAN = NO
Disk Write Cache Setting Of VD
or a
RAID 10
set, select
set, proceed to step 10.
Disk Write Cache
Virtual Drive(s) Congured
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
setting, and then press <Enter>.
Change DWC
Off
On
DWC
from the
Virtual
10. When nished setting the selected virtual drive conguration, select
Accept
from the menu, and then press <Enter>.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Congure Esc-Quit
6-8 Chapter 6: RAID conguration
BIOS Version A.08.09161344R
Virtual Drive(s) Congured
Easy Conguration - ARRAY SELECTION MENU
Virtual Drive 0
RAID = 1 Size = 77247MB DWC = Off
RA = On
Accept
SPAN = NO
Accept This VD Conguration And Go To Next VD
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
11. Follow step 2 to 10 to congure additional virtual drives.
12. Press <Esc> to nish RAID conguration. When prompted to save conguration, select
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Easy Conguration
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
New Conguration View/Add Conguration Clear Conguration Select Boot Drive
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
from the menu, and then press <Enter>.
Yes
BIOS Version A.08.09161344R
Conguration Menu
Virtual Drive(s) Congured
Select Yes Or No
Save Conguration?
Yes
No
UsingNewConguration
When a RAID set already exists, using the
NewConguration
erases the existing RAID conguration data. If you do not want to delete the
existing RAID set, use the
View/AddConguration
command to view or create
another RAID conguration.
command
To create a RAID set using the
1. From the
Management Menu
NewConguration
, select
option
Congure>NewConguration,
and
then press <Enter>.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Clear Existing Conguration And Start A New Conguration
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
ASUS RS700D-E6/PS8 6-9
BIOS Version A.08.09161344R
Conguration Menu
Easy Conguration
New Conguration
View/Add Conguration Clear Conguration Select Boot Drive
2. Follow step 2 to 7 of the previous section:
3. Select
Size
from the
Virtual Drive
UsingEasyConguration
menu, and then press <Enter>.
.
4. Key-in the desired virtual drive size, and then press <Enter>.
LSI Software RAID Conguration Utility Ver A.60 Jul 30, 2008
LD RAID Size #Stripes StripSz Status
0 1 77247MB 2 64 KB ONLINE
Management Menu
Congure
Initialize Objects Rebuild Check Consistency
Enter VD Size (MB): 77247
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
BIOS Version A.08.09161344R
Virtual Drive(s) Congured
Easy Conguration - ARRAY SELECTION MENU
Virtual Drive 0
RAID = 1
Size = 77247MB
DWC = Off
RA = On Accept
SPAN = NO
PORT #
DNLIN A00-00
0
DNLIN A00-01
1
Enter VD Size (MB):
5. Follow step 8 to 12 of the previous section:
UsingEasyConguration
create the RAID set.
to
6-10 Chapter 6: RAID conguration
Loading...