Page 1
2
2
1
1
100
TOOL KIT
To gain access to the tool kit, unlock and lift
the saddle as described on page 24 (UNLOCKING / LOCKING THE SADDLE).
The wrenches are fixed in the upper part of
the battery compartment cover.
The tool kit is formed by:
– No. 1 16 mm socket wrench (1);
– No. 1 17 mm wrench of the DIN type;
– No. 1 screwdriver (2) with one cross end
of the PH type, size 2, and opposite end
with hexagonal male wrench of 4 mm.
100
The wrenches are located in the comparment
found in the undersaddle plastic part.
The tool kit is formed by:
– No.1 16 mm socket wrench (1);
– No. 1 screwdriver (2) with one cross end
of the PH type, size 2, and opposite end
with hexagonal male wrench of 4 mm.
– No. 1 O ring for the two tools.
1
BAG HOOK
WARNING
Do not hang excessively bulky bags or
parcels to the hook, as this may seriously
compromise the manoeuvrability of the
vehicle or the movement of your feet.
The bag hook (3) is positioned on the front
part of the inner shield.
Max. allowed weight: 1.5 kg.
use and maintenance
Scarabeo 50 - Scarabeo 100 4T
25
Page 2
100
2
1
3
POSITIONING THE HELMET IN
THE REAR TOP CASE
Thanks to the rear top case, it is not necessary to take away the helmet with you everytime you park the vehicle.
WARNING
Never drive the vehicle with the rear top
case open as this may compromise
safety while riding.
To position the helment in the top case:
♦
Position the vehicle on the centre stand
as described on page 46 (POSITIONING
THE VEHICLE ON THE CENTRE
STAND)
♦ Remove the key from the ignition switch
26
.
and insert it in the lock (1) found on the
use and maintenance
Scarabeo 50 - Scarabeo 100 4T
rear top case.
♦ Turn the key anticlockwise and open the
rear top case (2).
♦ Put the helment (3) into the rear top case,
positioning it as shown in the figure and
on the label in the top case.
♦ Close the rear top case (2) until you hear
the click, remove the key from the lock (1).
CAUTION
Never leave the key in the lock.
Page 3
MAIN COMPONENTS
FUEL
WARNING
The fuel used for internal combustion
engines is extremely inflammable and in
particular conditions it can become explosive.
It is important to carry out the refuelling
and the maintenance operations in a wellventilated area, with the engine off.
Do not smoke while refuelling or near fuel
vapours, in any case avoid any contact
with naked flames, sparks and any other
heat source to prevent the fuel from
catching fire or from exploding.
Further, prevent fuel from flowing out of
the fuel filler, as it could catch fire when
getting in contact with the red-hot surfaces of the engine.
In case some fuel has accidentally been
spilt, make sure that the area is completely dry before starting the vehicle.
Since petrol expands under the heat of
the sun and due to the effects of sun radiation, never fill the tank to the brim.
Screw the cap carefully after refuelling.
Avoid any contact of the fuel with the skin
and the inhalation of vapours; do not
swallow fuel or pour it from a receptacle
into another by means of a tube.
DO NOT DISPOSE OF FUEL IN THE ENVIRONMENT.
KEEP AWAY FROM CHILDREN.
Use only premium petrol (4 Stars
) DIN
51600 standard, min. O.N. 98 (N.O.R.M.)
and 88 (N.O.M.M.).
Use only unleaded petrol, in conformity with
100
the DIN 51607 standard, min. O.N. 95
(N.O.R.M.) and 85 (N.O.M.M.).
To refuel, proceed as follows:
♦
Lift the saddle, see page 24 (UNLOCKING / LOCKING THE SADDLE).
♦ Unscrew and remove the fuel tank plug
(1).
1
1
100
FUEL T ANK CAPACITY
(reserve included): 8 l
TANK RESERVE: 1 l .
CAUTION
Do not put additives or other substances
into the fuel.
If you use a funnel or other similar items,
make sure that they are perfectly clean.
♦ Refuel.
WARNING
Make sure that the filler cap (1) is well
tightened.
♦ Put back the cap (1).
use and maintenance
Scarabeo 50 - Scarabeo 100 4T
27
Loading...