Alesis GuitarLink Wireless User Guide
GuitarLink Wireless
User Guide
English ( 2 – 6 )
Guía del usuario
Español ( 7 – 11 )
Guide d’utilisation
Français (12 – 16 )
Guida per l'uso
Italiano ( 17 – 21 )
Benutzerhandbuch
Deutsch ( 22 – 26 )
User Guide (English)
1. Make sure all items listed in the Box Contents are
included.
2. READ SAFETY INSTRUCTION BOOKLET BEFORE
USING THE PRODUCT.
3. Place the product in an appropriate location for
operation.
Support
For complete system requirements, compatibility information, and product registration, visit the
Alesis website: alesis.com/guitarlink-wireless.
For additional product support, visit alesis.com/support.
Quick Setup
1. Flip the power switch to the "On" position for the transmitter and receiver.
2. Press the Pair Button on both the transmitter and the receiver. The Pair LED will be lit
solid on the transmitter and receiver when they have successfully connected.
3. Set the receiver antenna to a vertical position.
4. Connect your guitar to the transmitter and adjust your guitar’s output volume.
5. Use a standard 1/4" cable (not included) to connect the receiver's Amp Output to your
amplifier.
6. Set the volume control on the receiver to the highest level possible without distorting or
clipping the guitar signal. This level will vary with the settings of your guitar's volume and
your guitar amplifier's gain and/or volume. Adjust your guitar amplifier's volume last.
2
BOX CONTENTS
GuitarLink Wireless
Transmitter
GuitarLink Wireless
Receiver
Power Adapter
2 AAA Batteries
User Guide
Safety & Warranty Manual
Connection Diagram
Transmitter
Receiver
Guitar*
Amplifier*
* Sold
separately
3
1
2
1
2
3
1
3
1
1
2
1
3
Transmitter Features
Front Panel
1. Pair Button – Press this button to connect to the
receiver. The Pair LED will illuminate when connected
to the receiver.
2. Pair LED – Illuminates when the transmitter is
connected with the receiver.
3. Power LED – Illuminates when the transmitter is powered on.
Rear Panel
1. Battery Compartment – Insert 2 AAA batteries here
to power the transmitter.
2. On/Off Switch – Slide this switch to power the
transmitter on.
3. Guitar Cable – Connect the attached 1/4” cable to
your guitar’s 1/4” output.
Bottom Panel
1. Guitar Strap Clip – Use the attached clip to secure
the GuitarLink Wireless transmitter to your guitar strap
or to your pocket.
4
2
3
4
1
2
3
4
1
2
1
2
3
1
1
3
4
5
2
1
1
Receiver Features
Front Panel
1. Pair Button – Press this button to
connect to the transmitter. The Pair
LED will illuminate when connected
to the transmitter.
2. Pair LED – Illuminates when the
receiver is connected with the
transmitter.
3. Power LED – Illuminates when the receiver is powered on.
4. Volume – Adjusts the volume of the signal going to the Amp Output.
5. Amp Output – Use a standard 1/4" cable (not included) to connect the GuitarLink
Wireless receiver to your amplifier.
Rear Panel
1. Battery Compartment – Insert 2 AAA batteries
here to power the receiver.
2. On/Off Switch – Slide this switch to power the
receiver on.
3. Power Input – Connect the included 5V 1A,
Center-Pin Positive power adapter here.
4. Antenna – Place the antenna in a vertical
position for best results in transmitting the wireless signal. If the wireless signal quality is
poor, change the position of the antenna.
5
Troubleshooting
No signal:
• Make sure both the transmitter and receiver are powered on.
• Make sure you are within the 60-foot (20-meter) transmitting range.
• Make sure the transmitter and receiver have been paired.
• Adjust the output volume on your guitar.
• Make sure the volume controls on your mixer and speakers are turned up.
• Check the power LEDs on both the receiver and transmitter. If one of them is off, check
that the device is powered correctly:
o Install fresh AAA batteries in the transmitter.
o Connect the power adapter to (or install fresh AAA batteries in) the receiver.
Weak signal:
• Adjust the output volume on your guitar.
• Make sure there are no objects (computers, walls, furniture, etc.) between the transmitter
and receiver.
• Make sure you are within the 60-foot (20-meter) transmitting range.
• If the transmitter or receiver is being powered from batteries, install fresh AAA batteries.
Poor signal quality:
• Keep any connected audio cables away from the receiver’s antenna.
• If the transmitter or receiver is being powered from batteries, install fresh AAA batteries.
6
Guía del usuario (Español)
1. Asegúrese de que estén presentes todos los elementos
enumerados en Contenido de la caja.
2. LEA EL FOLLETO DE INSTRUCCIONES DE
SEGURIDAD ANTES DE UTILIZAR EL PRODUCTO.
3. Coloque el producto en un lugar adecuado para su
funcionamiento.
Soporte
Para obtener información completa sobre requisitos del sistema, compatibilidad y registro del producto,
visite el sitio web de Alesis: alesis.com/guitarlink-wireless.
Para soporte adicional del producto, visite alesis.com/support.
Instalación rápida
1. Coloque el interruptor de encendido en la posición "On" (Encendido) en el transmisor y el receptor.
2. Pulse el botón Pair (Aparear) en el transmisor y el receptor. Cuando se conectan exitosamente, el LED
Pair se enciende con luz fija en el transmisor y el receptor.
3. Coloque la antena del receptor en posición vertical.
4. Conecte su guitarra al transmisor y ajuste el control de volumen de salida de la guitarra.
5. Use un cable de 1/4 pulg. estándar (no incluido) para conectar la salida Amp (Amplificador) del receptor
a su amplificador.
6. Ajuste el control de volumen del receptor al máximo nivel posible sin distorsionar o recortar la señal de
la guitarra. Este nivel varía en función de los ajustes de volumen de su guitarra y de ganancia y/o
volumen de su amplificador de guitarra. Ajuste el volumen de su amplificador de guitarra.
7
CONTENIDO DE LA CAJA
Transmisor GuitarLink
Wireless
Receptor GuitarLink Wireless
Adaptador de alimentación
2 pilas AAA
Guía del usuario
Manual sobre la seguridad y
garantía
Diagrama de conexión
Transmisor
Receptor
Guitarra*
Amplificador*
* Se vende por
separado
8
1
2
1
2
3
1
3
1
1
2
1
3
Características del transmisor
Panel frontal
1. Botón de encendido – Pulse este botón para
encender el receptor. Cuando se conecta al receptor,
se enciende el LED Pair.
2. LED Pair – Se ilumina cuando el transmisor se
conecta con el receptor.
3. LED de encendido – Se ilumina cuando se enciende
la unidad.
Panel trasero
1. Compartimiento de las pilas – Inserte aquí 2 pilas
AAA para alimentar el transmisor.
2. Interruptor de encendido – Deslice este interruptor
para encender el transmisor.
3. Cable de guitarra – Conecte el cable de 1/4 pulg.
incluido a la salida de 1/4 pulg. de su guitarra.
Panel inferior
1. Presilla para correa de la guitarra – Use la presilla
incluida para sujetar el transmisor GuitarLink Wireless
a la correa de su guitarra o a su bolsillo.
9
Loading...