Processeur d’effet s Gui tar FX
Guide de l’utilisateur
Schnelles Hinweisbuch (Deutsch)
Box Contents:
GuitarFX Effekt Prozessor
Gebrauchsanleitun
Manuale rapido di utilizzazione (Italiano)
Contenuto della Confezione:
Processore Effetti GuitarFX
Manuale d’Uso
GuitarFX Hookup Diagram
9V
Adapter
Headphones
GuitarFX
Guitar
Control
Pedal
Amplifier
Quick Setup for the GuitarFX
1. Make sure all items listed on the front
of this guide are in the GuitarFX’s box.
2. Read the Important Safety Instructions
starting on page 7 of the User Manual.
3. Study the Hookup Diagram above.
4. Make sure all devices and instruments
are turned off and all gain knobs set to
zero.
5. Connect your guitar and amplifier (and
control pedal and headphones if
applicable) to the GuitarFX in the
manner illustrated above. Refer to the
Connection Details below for details
on which cables to use.
6. Plug in all devices.
7. Experiment with the GuitarFX’s effect
combinations. Refer to the quick
reference on the next page for help.
8. When finished, turn off the amp before
disconnecting any equipment to
prevent damage to the speaker.
9. Go to http://www.alesis.com to
register the GuitarFX.
Connection Details
Features of the GuitarFX
1. Display – Indicates bank and program,
shows parameter values and displays
pitch in tuner mode.
2. EFFECT Knob – Puts the GuitarFX
in PLAY mode or EDIT mode. You
are in EDIT mode when you select a
module or parameter with this knob.
3. VALUE Knob – Adjusts parameter
values, program numbers and master
volume; stores changes.
4. Left Foot Pedal – Decrements
program number; when used with the
right foot pedal, puts the unit in
BYPASS and MUTE modes and
accesses the tuner.
5. Right Foot Pedal – Increments
program number; when used with the
left foot pedal, puts the unit in
BYPASS and MUTE modes and
accesses the tuner.
1. INPUT Jack – A 1/4” monophonic high impedance unbalanced
input. If you’re using battery power, the unit powers on when you
insert a plug here.
2. CONTROL Jack – a 1/4” jack where you can connect a control
pedal for controlling effects.
3. 9VDC Jack – compatible with most 9VDC adapters. The unit
powers on as soon as you connect the adapter.
4. OUTPUT Jack – a stereo 1/4” unbalanced jack for headphones.
You may use a stereo-to-mono Y cable to connect this to two
amplifiers.
Effect Quick Reference
Refer to chapter 10 of the User Manual
for more details on effect modules.
1. COMP/LIMIT – increasing levels of
compression (C1-C9) and limiting (L1L9).
2. DIST – various types of distortion.
3. DRIVE – controls the drive/gain for
the DIST module; control pedal may
be used.
4. EQ – 50 separate values that cover the
gamut of possible EQ settings. See
page 26 of the User Manual for details.
5. NR – noise reduction and hum
elimination working together. left digit
of the display shows the level of hum
elimination and right digit shows level
of noise reduction.
6. CAB – settings C1 – C3 simulate 1 x
12”, 2 x 12” and 4 x 10” cabinets
respectively.
7. FX1 – various mono effects; most have
a separate setting for pedal control.
8. PARAM – direct-control parameter for
FX1; for most effects, can be set to
pedal control independent of the FX1
setting.
9. FX2 – stereo versions of the effects
found in FX1, with several additions;
these also have settings for pedal
control.
10. PARAM – direct-control parameter for
FX2; for most effects, can be set to
pedal control independent of the FX2
setting.
Visual Guide to Tuning
The bottom four segments rotate counterclockwise if
pitch is low. The top four rotate clockwise if the
pitch is high. An 8 means you’re in tune.
11. FX3 – various delay-based effects;
most have pedal-controlled versions.
12. PARAM – direct-control parameter for
FX3; for most effects, can be set to
pedal control independent of the FX3
setting.
13. DIGIFX – a couple of digital-sampling
effects with pedal-controlled versions.
14. LEVEL – the level of the current
program.
15. ROUTE – eight variations of the
routing order of all nine effect modules.
Selecting, Editing and Storing
Programs
1. In PLAY mode, use the foot pedals or
VALUE knob to select a program.
2. Turn the EFFECT knob to the module
or parameter you wish to edit.
3. Turn the VALUE knob to change the
value of the module or parameter.
4. To store your changes, press the
VALUE knob and then turn the knob
to select a store location. Press the
VALUE knob again to store the
program.
Using the Tuner
1. In PLAY mode, activate the tuner by
pressing both pedals at the same time
to enter BYPASS mode, or hold down
the pedals for more than half a second
to enter MUTE mode.
2. Play the open string you wish to tune.
Use the following guide when tuning:
Low
In tune
High
= no pitch detected.
Here are the 12 possible
pitches (a decimal point
indicates a sharp):
Diagrama montaje de GuitarFX
Adaptador
de 9V
Guitarra
GuitarFX
Auriculares
Instalación rápida para el GuitarFX
1. Asegúrese de que todos los artículos incluidos
al inicio de este manual están incluidos en la
caja del GuitarFX.
2. Lea las importantes instrucciones de seguridad
que comienzan en la página 7 del Manual de
usuario.
3. Estudie el diagrama de montaje que aparece
más arriba.
4. Asegúrese de que todos los dispositivos e
instrumentos están apagados y de que todos
los controles de ganancia están en posición
“cero”.
5. Conecte su guitarra y su amplificador (y
pedalera de control y auriculares si es
aplicable) al GuitarFX de la manera que se
muestra abajo. Remítase a “Detalles de
conexión” más abajo para detalles sobre qué
cables utilizar.
6. Enchufe todos los dispositivos.
7. Experimente con las combinaciones de
efectos de GuitarFX. Si necesita ayuda,
remítase a la referencia rápida en la página
siguiente.
8. Cuando haya terminado, apague el
amplificador antes de desconectar ningún
equipo para evitar daños al bafle.
Visite http://www.alesis.com para
9.
registrar el GuitarFX.
Amplificador
Pedal de
Control
Detalles de conexión
Características del GuitarFX
1. Display – Indica banco y programa, muestra
los valores del parámetro y puede visualizarse
el pitch en modo sintonizador.
2. Botón de EFECTOS – Pone el GuitarFX en
modo PLAY [Tocar] o EDIT [Editar]. Se
encuentra en modo EDITAR cuando
selecciona un módulo o parámetro con este
botón.
3. Botón de VALOR – Ajusta los valores del
parámetro, los números de programa y el
volumen del master; almacena los cambios.
4. Pedal del Pie Izquierdo – Disminuye el
número de programa, cuando se utiliza junto
con el pedal del pie derecho, pone la unidad
en los modos de BYPASS y MUTE
[SILENCIO] y accede al sintonizador.
5.
Pedal del Pie Derecho – Aumenta el
número de programa, cuando se utiliza junto
con el pedal del pie izquierdo, pone la unidad
en los modos de BYPASS y MUTE
[SILENCIO] y accede al sintonizador.
1. Jack de ENTRADA– Una entrada no balanceada de alta
impedancia monofónica de ¼”. Si está utilizando alimentación por
batería, la unidad se enciende cuando inserta en el enchufe aquí.
2. Jack de CONTROL – un jack de 1/4” donde puede conectar un
pedal de control para controlar los efectos.
3. Jack de 9VDC– compatible con la mayoría de los adaptadores
9VDC. Esta unidad se enciende cuando conecta el adaptador.
4. Jack de SALIDA– un jack estéreo de 1/4” no balanceado para
auriculares. Puede usar un stereo-a-mono Y cable para conectar
esto a dos amplificadores.
Loading...
+ 7 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.