Akai DVR3400SSBOX, DVR3400SS User Manual

Important Safety Instructions
WARN I NG
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this owner manual.
WARNI NG:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
INVISIBLE LASER RADIATION WHEN
CAUTION
OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM
This symbol means that the unit complies with European safety and electrical interference directives.
This product contains a low power laser device.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASS E 1
PRODUCTO LASER DE CLASE 1
PRODUTO LASER CLA SSE 1
The symbol for Class II (Double lnsulation)
On Placement
• Do not use the Unit in places which are extremely hot, cold, dusty, or humid.
• Place the Unit on a flat and even surface.
• Do not restrict the air flow of the Unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on carpeting.
On Safety
• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard.
• When you are not going to use the Unit for a long period of time, disconnect the AC power cord.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the Unit. When there is condensation inside the Unit, the Unit may not function normally. Let the Unit stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the Unit before use.
WARNING:
• Should any trouble occur, disconnect the AC power cord and refer servicing to a qualified technician.
• Do not place anything directly on the top of the Unit. Damage to the Unit can result.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, rent copyrighted material without permission.
Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098 and 4,907,093 licensed for limited viewing uses only.
DVD video discs are copy protected, and any recordings made from these discs will be distorted. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
- 1 -
Table of Contents
Important Safety Instruction ....................... 1
Disc Formats ................................................ 3
Before You Start ........................................... 4
Using the remote control .......................................... 4
Parts and Functions .................................. 5-8
Front Panel ................................................................. 5
Subwoofer.................................................................. 6
Remote Control ...................................................... 7-8
Display ........................................................ 9
Front Panel Display .................................................. 9
Display Information .................................................. 9
Setup ......................................................10-15
For better reception ................................................. 10
Connecting your TV ................................................. 10
Connecting a VCR .................................................... 11
Connecting another source .................................... 12
Connecting the speakers & subwoofer .................. 13
Positioning the speakers and subwoofer .............. 14
Mounting rear surround speakers .......................... 15
Turning on the Unit and TV ...................................... 15
Power cord connection ........................................... 15
Adjusting the Sound ............................. 16-17
Playing a Disc ....................................... 18-21
Playing Disc ............................................................. 18
Pausing playback (still mode) ............................... 18
Stopping playback ................................................. 18
To skip to a different track ...................................... 18
Fast Foward/Fast Reverse ..................................... 19
Slow-motion play ................................................... 19
Skip (Forward/Reverse) .......................................... 19
Zooming into an image ......................................... 19
Angle selection ....................................................... 20
Audio selection ....................................................... 20
Subtitle selection .................................................... 21
Special Functions ................................. 22-24
Display function (DVD) .......................................... 22
Locating a specific title ......................................... 23
Locating a specific title/chapter/track .................. 23
Locating a specific time ......................................... 24
Angle setting ........................................................... 24
Audio setting .......................................................... 24
Subtitle setting ....................................................... 24
CD / DVD programmable memory ............... 25
DVD programmable memory ................................. 25
Title/Chapter programmed playback ............. 25
CD programmable memory ................................... 25
Track programmed playback .......................... 25
Repeat Playback ................................... 26-27
Repeating a title/chapter (DVD) ............................ 26
Repeating a single track/whole disc (CD) ........... 26
Repeating a specific section (DVD) ...................... 27
Playing MP3 and Picture File Disc......... 28-29
Playing a MP3 file disc ............................................ 28
Playing a Picture file disc ....................................... 29
Playing a MP3/Picture file disc ............................... 29
Radio Operation .................................... 30-31
Tuning into a station manually ............................... 30
FM Stereo ............................................................. 30
Weak FM stations ............................................... 30
To search for a station automatically ................ 30
Presetting stations ................................................... 30
Tuning into a preset station .................................... 30
RDS station service .................................................. 31
Program types (PTY) ................................................ 31
RadioText .................................................................... 31
Customizing the Function Settings ........ 32-40
LANGUAGE setting .................................................. 32
VIDEO setting ............................................................ 33
TV Shape .............................................................. 33
Video Output ....................................................... 34
Brightness ............................................................ 34
Edges .................................................................... 35
AUDIO setting ........................................................... 36
Digital Out ............................................................ 36
L/R speaker .......................................................... 36
Subwoofer ............................................................ 37
Surround Delay ................................................. 37
Center Delay ...................................................... 38
Pink noise .......................................................... 38
RATING setting ......................................................... 39
Password/Parental lock ..................................... 39
Factory Set .......................................................... 40
Language Code List for Disc Language ....... 41
Maintenance ................................................ 42
Cleaning Disc .......................................................... 42
Cleaning the Unit ................................................... 42
Important Note ....................................................... 42
Trouble Shooting Guide ........................ 42-43
Specifications ............................................. 44
- 2 -
Disc Formats
The Unit can playback discs bearing any of the following marks:
DVDs [8cm(3")/12cm(5”) disc]
Audio CDs [8cm(3")12cm(5”) disc]
Region Management Information
Region Management Information: This Unit is designed and manufactured to respond to the Region Management Information that is encoded on DVD discs. If the Region number printed on the DVD disc does not correspond to the Region number of this Unit, this Unit cannot play that disc.
Compatible
The region number of this Unit is 2.
Disc Function or Operation that is Not Available
2
When the symbol appears on the TV screen, it indicates that the function or operation attempted is not available at that time. This occurs because the DVD disc manufacturer determines the specific functions. Certain functions may not be available on some discs. Be sure to read the documentation provided with the disc.
Icons Used on DVDs
Sample lcons
1. English
2
2
2. French
1. English
2. French
Language selections for audio Language selections for subtitles
Screen aspect ratio
2
Multiple camera angles Region code indicator
Notes:
• This Unit supports 2-channel (L/R) audio and 5.1ch (Multi-channel) MPEG Audio 1/2 (only when the DIGITAL AUDIO OUT coaxial jack is used for connection). It does not support 7.1 channel MPEG Audio Version 2.0.
• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown.
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the disc has more than one movie on it, each movie would be a separate “title”. “Chapters” are sections of titles.
T
Chapter 1 Chapter 1Chapter 2 Chapter 2Chapter 3
• Audio CDs are divided into “tracks”. A “track” is usually one song on an Audio CD.
Track 1 Track 2 Track 3 Track 4 Track 5
Note :
• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do not.
Notes on Unauthorized Discs
You may not be able to play back some DVD discs on this Unit if they were purchased from outside your geographic area or made for business purposes.
- 3 -
Before Y ou Start
Using the Remote Control
• Point the Remote Control at the REMOTE SENSOR located on the Unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
To install Batteries
1.Open the battery door.
Battery Replacement
When batteries become weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the batteries.
2. Insert two "AA" or UM-3 size batteries.
Notes:
• If the Remote Control is not going to be used for a long time, remove the batteries to avoid damage caused by battery leakage corrosion.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries.
- 4 -
Parts and Functions
Front Panel
14
1) Disc tray
Open or close tray by pushing OPEN/CLOSE button. Place a disc on the disc tray, label side up.
2) PRO LOGIC indicator
When DOLBY PRO LOGIC sound selected in AV_IN mode, the light will illuminate.
3) standby indicator When the Unit is turned on by pressing the POWER/ STANDBY button, the light will illuminate. If you press POWER button on the Remote control. The Unit will turn on.
4) 3 STEREO indicator
When 3 STEREO sound selected in AV_IN mode, the light will illuminate.
5) Display window
Display system information.
6) VOLUME control
Change the loudness of the sound from the speakers connected to the Unit.
7) Remote sensor
Accept the remote control unit signals.
13452
8) FUNCTION button
9)
10) PAUSE button
11) PLAY button
12)
13) OPEN/CLOSE button
14) POWER/STANDBY button
6
8910111213
Select the source.
STOP button
Stop playing a disc.
Press to pause playback. Each time you press the PAUSE button the picture advances one frame. Press the PLAY button to resume.
Press to start or resume playback
SKIP buttons
Press SKIP tracks.
Press SKIP button to advance to chapters / tracks. Press and hold SKIP button to begin fast scan. Four speeds are available.
Scan all available radio stations.
Use to open and close the disc tray.
Turn the power on or off.
button to go back to previous chapters/
7
Note:
Screen saver - If no button is pressed within 3 minutes, the function will active, If you want to return the normal screen, press any button.
Rear Panel
15) FM 75 ANTENNA jacks
16) VIDEO OUT jack
17) SCART SOCKET
18) AM LOOP ANTENNA terminal
19) DIGITAL AUDIO OUT jack
20) Left/Right AUDIO OUT jacks
15 16 17
18
19 20 21 22 23 24 25
- 5 -
SUBWOOFER AUDIO OUT
5.1 CH
21) S-VIDEO (DVD) Output jack
22) VIDEO IN (VCR) jack
23) AV IN (AUDIO IN) L&R jack
24) SUBWOOFER AUDIO OUT jack
25) Power cord
(Continued on next page)(Continued on next page)
(Continued on next page)
(Continued on next page)(Continued on next page)
Sub-Woofer
Parts and Functions
Front Panel
Rear Panel
33
26) Front speaker (R) terminals
27) SUBWOOFER AUDIO IN 5.1CH jack
28) Rear speaker (R) terminals
29) Center speaker terminals
30) Rear speaker (L) terminals
31) Front speaker (L) terminals
32) Power cord
33) POWER indicator
26
27
28
29
30
31
32
- 6 -
(Continued on next page)(Continued on next page)
(Continued on next page)
(Continued on next page)(Continued on next page)
Remote Control
POWER
1
2
3
4
MEMORY
5
DIMMER
6
PRO LOGIC
7 8
SETUP MENU
9 10
SLOW SLOW
11 12
STOP
13
PREV
14 15 16
CLEAR
ANGLE SU BTITLE FM M O DE BAND
17 18
Parts and Functions
OPEN/
2.1 CH5.1 CH
PAUS E
A-B D ISC
REPEAT
CLOSE
GOTO
SOUND
FUNCTION
RETURN
VOLUM E
ENTER
PLAY
TUNING NEXT
DISPLAY ZOOM AUDIO
1) POWER / button
Turns the Unit power on and puts it in standby mode.
2) RETURN button
Return to the normal operation after using the SETUP menu.
3) Number (0 - 9) and (+10) buttons
Use when creating programs, and entering a parental level password. To select numbers over 9, press +10 button and then the second no. for example, to enter 18, press +10 and then 8.
4) 5.1 Ch button
Switch speaker outputs by 5 speakers mode.
5) MEMORY button
Enter the number of a selected chapter or track. Enter the number of a selected station.
6) DIMMER button
Adjust the brightness of the front panel display to the level you prefer.
7)
PRO LOGIC button
Set Dolby Pro Logic feature in AV_IN mode.
8) VOLUME (+ / -) buttons
Change the loudness of the sound from the speakers connected to the Unit.
9) SETUP button
Open and close the Unit's SET UP menu screen.
/ CURSOR buttons
10)
Use to highlight selections on a menu screen and adjust certain settings.
11)
SLOW button
Perform slow reverse playback of DVDs.
TUNING buttons
12)
: Fast reverse playback. : Fast forward playback. TUNING : Scan all available radio stations.
13) STOP button
Stop playback.
14) PREV button
Move reverse through titles, chapters or tracks on a disc. Tune to the presetted stations.
15) CLEAR button
Clear input selections and cancel certain playback functions.
16) DISPLAY button
Change disc status information displayed on the TV.
17) ANGLE button
Switch the camera angle of the video presentation when scenes with multiple camera angles are recorded on a DVD.
18) SUBTITLE button Select one of the subtitle languages programmed on a DVD.
.....
- 7 -
(Continued on next page)(Continued on next page)
(Continued on next page)
(Continued on next page)(Continued on next page)
Remote Control
POWER
FUNCTION
RETURN
MEMORY
DIMMER
PRO LOGIC
SETUP MEN U
SLOW SLOW
STOP
PREV
CLEAR
DISPLAY ZO O M AUDIO
ANGLE SUBTITLE FM M O DE BAND
2.1 CH5.1 CH
VOLUME
ENTER
PLAY
TUNING NEXT
A-B DISC
REPEAT
OPEN/
CLOSE
GOTO
SOUND
PAUS E
Parts and Functions
19) FUNCTION button
19
20 21
22 23
24 25
26 27
28 29
30 31
32 33
34
Display the FUNCTION screen where you can check or change various setting.
20) OPEN / CLOSE button
Use to open or close the disc tray.
21) GOTO button
Skip directly to a specific location on a DVD disc.
22) SOUND button
Selects sound balance and tone controls for adjustment with the cursor buttons.
23) 2.1 CH button
Switch speaker outputs by 2 speakers mode.
/ CURSOR buttons
24)
Use to highlight selections on a menu screen and make adjust certain settings.
25) MENU button
Open and close DVD's menu.
26) ENTER button
Confirm selections on a menu screen.
27 ) SLOW button
Perform slow forward playback of DVDs.
28) PLAY button
Start playback.
PAUSE button
29)
Pause playback, frame advance.
30 ) NEXT
Move forward through titles, chapters or tracks on a disc.
Tune to the presetted stations.
31) AUDIO button
Select one of the audio soundtracks programmed on a DVD or selects the audio output mode on a AUDIO CD.
32) ZOOM button
Zoom into an image.
33) BAND/REPEAT-DISC button
Switch between AM(MW) or FM. Repeat chapter or title of a DVD. Repeat single track or whole CD.
34) FM MODE / REPEAT A - B button Set FM MODE to FM STEREO for FM stereo sound
or to FM MONO for mono sound. Perform point-to-point repeat playback on a DVD or
CD.
button
- 8 -
Display
Front Panel Display
CHAPTER / TRACK indicator
When a DVD is loaded in the Unit, this indicator appears along with the chapter number. When a Audio CD is loaded in the Unit, this indicator appears along with the track number.
STEREO indicator
Tune into a station. "((ST))" will appear when an FM broadcast is in stereo.
REPEAT 1 playback indicator
Displayed during repeat playback.
MEMORY indicator
Displayed during programmed playback.
ANGLE indicator
Appears when multiple camera angles are recorded in the section of the DVD that is currently playing.
R. T O TAL(REMAIN.T OTAL) indicator
Indicates the elapsed playback time of the disc. With some discs, this area also shows the total play time of the disc when playback is stopped.
TITLE indicator
When a DVD is loaded in the Unit, this indicator appears along with the title number.
REPEAT A-B playback indicator
Displayed during repeat playback.
OPERA TION indicator
Indicates the operation status of the disc and Unit.
DOLBY DIGITAL indicator
Displays while Dolby Digital sound processing is being performed or when the loaded disc contains Dolby Digital sound.
Display Information
The DVD displays the information shown below on the TV screen and on the Unit's DVD display depending on the operation status.
Display Examples
If no disc is loaded when the Main Unit is switched on.
Tray open
TV Screen
No Disc
Open
Unit Display
Remarks
"
" appears when the tray is closed and:
1)There is no disc in the tray.
2) The disc type is not playable in this Unit.
3) The disc is not loaded correctly (upside-down, etc.)
Tray closed Loading Stopped
Playing Paused
Fast forward Fast reverse Slow
Repeat A - B
Close
Loading...
Stop
Play
Pause
x 2
x 2
x 1/2
/
A -
B
A-B
The display changes to show other indicators (total time, etc.)
Freezes the image on the screen or pauses audio playback. The display changes to show other indicators (total
time, etc.) Does not function for Audio CDs. Repeat a specific section.
The operation is not permitted by the DVD Unit or the disc.
Region (Local) Number Error Indicator
If the region (local) number of the disc that you attempt to play differs from the region number of the Unit. "Invalid Region" appears on the TV screen. (The disc cannot be played).
- 9 -
Setup
For better reception
FM
Connect FM antenna (included) to the FM ANTENNA jack.
AM(MW)
Connect the loop antenna (included) to the AM(MW) LOOP ANTENNA terminals.
FM antenna
SUBWOOFER AUDIO OUT
5.1 CH
To wall outlet
AM(MW) LOOP ANTENNA (SUPPLIED)
A.Connecting your TV
The Unit can be connected to your TV in several different ways, depending on the design of your TV.
RCA-SCART 3 Phono/Scart AV cable
Use the included 3 Phono/Scart AV cable
1. Connect the VIDEO OUT and left/right AUDIO OUT jacks to the SCART on your TV.
or
S-Video Jack
Use an S-Video cable (sold separately).
• Use an S-Video cable to connect the S-VIDEO (DVD) jack on your Unit to the S-VIDEO IN jack on your TV.
TV
To AUDIO OUT
DVD Unit
(w h ite)(red)(y ellow )
3 Phono/Scart AV cable
SCART cable (not i ncluded)
- 10 -
(continued to next page)(continued to next page)
(continued to next page)
(continued to next page)(continued to next page)
Setup
R
B. Connecting a VCR
1. Using the supplied 3 Phono/Scart AV cable, connect the yellow plug from VIDEO OUT jack on your Unit to SCART jack on your TV, connect the left and right AUDIO OUT jac ks on your Unit to SCART jacks on your TV. If you want the sound come from the speakers of the Main Unit, you need not to connect these left and right Audio cable from the Main Unit to your TV.
2.Using the Video cable (not supplied), connect the VIDEO IN (VCR) jac k on y our Unit to VIDEO OUT jac k on your VCR.
3.Using the Audio cable (not supplied), connect the left/right AUDIO IN jac ks on your Unit to the A UDIO OUT jac ks on your VCR.
To AUDIO
OUT
(y ellow )
(red )
DVD Unit
To V ID E O I N
(w h ite)
(y ellow )
(y ellow )
(red )
(w h ite)
To AUDIO IN
3 Phono/Scart AV cable
TV
To AUDIO
OUT
(w h ite)(red )
VC
AUDIO OUT
To V ID E O OUT
(y ellow )
Watching a DVD
1.Turn on the Unit, use the FUNCTION button on the remote control or the front panel to select "DVD".
2.Turn on your TV and follow the instructions included with it to select VIDEO function which is correspond to the VIDEO IN jack you need connected with the Main Unit.
Watching a Videotape
1.Turn on the Unit, use the FUNCTION button on the remote control or the front panel to select "AV_IN".
2.Turn on your TV and follow the instructions included with it to select VIDEO function which is correspond to the VIDEO IN jack that is connected with the Main Unit.
3. Turn on the VCR and follow the instructions included with it to play the videotape.
Notes:
• When playing VCR, you want the sound come from the speakers (supplied), you need not connect the Video cable.
• If VCR Audio is mono, surround speakers sound level will be low.
(continued to next page)(continued to next page)
(continued to next page)
- 11 -
(continued to next page)(continued to next page)
Setup
C. Connecting another source
Using the not supplied Audio/Video cable, connect ONLY the left and right AUDIO OUT jack on your Unit to the AUDIO IN jack or use a coaxial digital Audio cable (not supplied) to connect to the coaxial in jack on your another equipment. Do not connect the yellow video plug.
Listening to an other audio equipment
1. Turn on the Unit.
2.Turn on your audio equipment and follow the instructions included with it to select the AUDIO IN or DIGITAL IN function.
Analogue connection
Amplifier of stereo
DVD Unit
system, etc. (no t incl uded )
AUDIO IN
Digital connection
To AUDIO OUT
(w h ite)(r ed )(yello w )
To A U DIO I N
(w h ite)
(red )
(y ellow )
Audio equipment with
DVD Unit
Notes:
• If the external equipment is a television and this audio system is close to it, you may experience interference
if the tuner function is selected while the television is working.
• When you have selected TUNER function, sound will ONLY come from the front left, right speakers and
subwoofer.
• Ensure that a VCR connected to this Unit is set to stereo mode otherwise the activated speakers may be
different from those outlined in the table on page 17.
• Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the
resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.
• When playing VCR, press the FUNCTION button on the remote control or front panel to AV_IN mode, all
speakers will be activated a few minutes later.
digital audio input jack
COAXIAL
- 12 -
(continued to next page)(continued to next page)
(continued to next page)
(continued to next page)(continued to next page)
Setup
D. Connecting the speakers & subwoofer
1. The speaker cords have been color-coded to simplify connection. Just plug the POSITIVE (+) and NEGATIVE (-) ends of each speaker wire into the corresponding jacks on the rear of the Unit, matching the color tube on the end of the speaker wire to the color-coded connector.
2. Connect each of the speaker wires to the satellite speakers. The front left/right and rear left/right speakers are all the same. However, make sure you connect to the center speaker (color) to the one speaker which is slightly longer than the rest.
MAIN UNIT
Manufactured unde r license from D olby Laboratori es. Do lby the double-D symbol are trademarks of Dolby Confidential Unpub lishe d Work s. All rights reserved. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093 licensed for limited viewing u ses only.
and
Laboratories.
© 1992-1997 Dolby Laboratories, lnc.
VIDEO IN
CLASS 1 LASER PRODUCT APPAREIL À LASER D E CLASSE 1 PRODUCTO LASER DE CLASE 1 PRODUTO LASER CLASSE 1
To
To
AUDIO IN
TELEVISION
FRONT (RIGHT)
DTS a nd D TS Digi tal O ut are trademarks of Digital Theater Systems, Inc.
SUBWOOFER AUDIO OUT
SUBWOOFER
5.1 CH
AUDIO OUT
5.1 CH
SUBWOOFER
FRONT (LEFT)
CENTER
CENTER
+
CENTERREAR (RIGHT)
- 13 -
REAR (LEFT)
+
(continued to next page)(continued to next page)
(continued to next page)
(continued to next page)(continued to next page)
Loading...
+ 31 hidden pages