Page 1
Reference Guide
© 2015 ZOOM CORPORATION
Copying or reprinting this manual in part or in whole without
permission is prohibited.
Page 2
—2—
Introduction
is a mixer application designed specifically for the .
Using a computer, you can make settings for the built-in mixer and for the high-quality monitoring effects.
Functions include LO CUT, PHASE reversal and AUTO GAIN, which automatically detects input signal levels.
Other functions are LOOPBACK, which sends the input signal and computer signal back to the computer, and MEMORY, which allows you to save settings with one
touch.
Installing and Launching
1. Download to the computer
Download the application from the ZOOM website (http://www.zoom.co.jp/
downloads).
HINT
• You can download the latest ZOOM from the above website.
• Download for the operating system that you are using.
2. Launch the installer and install .
Follow the instructions that appear on screen to install .
3. Launch
When you connect a to a computer using a USB cable,
will launch automatically.
HINT
• See the operation manual for instructions about connecting it with a
computer.
• If it does not launch automatically, launch manually from where
it is installed on the computer.
Page 3
—3—
Names of Parts/Basic Operations
Setting the inputs
P.5
Setting the built-in
mixer for each output
jack
P.7
Checking computer settings/
Using the loopback function/
Selecting the clock source
P.6
Setting the upsampling function
P.10
Saving and loading settings
P.11
Setting the effect
P.9
Setting output levels
P.8
Basic operations
•
Click a knob and drag up or down to adjust it.
•
Press the shift key while moving a knob to make fine adjustments.
•
Click a knob value to allow direct entry of the value.
•
Click a button to turn it on/off.
• Follow the procedures below to set the sampling rate.
Windows Open the Control Panel, then "Hardware and Sound" and change it on the ZOOM UAC-8 Control Panel.
Mac Open the Utilities folder in the Applications folder, double-click the Audio MIDI Setup application, and then select the UAC-8.
Page 4
—4—
Mixer Block Diagram
PHONES1
VOLUME
FADER
FADER PAN
LEVEL
METER
L R
EFX RETURN
OUTPUT
VOLUME
SWITCHER
PHONES2
MAIN OUT L
LINE OUT 1
LINE OUT 2
LINE OUT 3
LINE OUT 4
LINE OUT 5
LINE OUT 6
LINE OUT 7
LINE OUT 8
S/PDIF OUT
ADAT OUT
MAIN OUT R
MIXER
MAIN OUTPUT+PHONES1
ADAT8
ADAT7
ADAT6
ADAT5
ADAT4
ADAT3
ADAT2
ADAT1
INPUT8
INPUT7
S/PDIF R
S/PDIF L
INPUT6
INPUT5
INPUT4
INPUT3
INPUT2
INPUT1
LINE OUTPUT1/2
LINE OUTPUT3/4
LINE OUTPUT5/6
LINE OUTPUT7/8
S/PDIF OUT
ADAT OUT1/2
ADAT OUT3/4
ADAT OUT5/6
ADAT OUT7/8
COMPUTER
INPUT
EFFECT
EFX SEND
REVERB & DELAY
LEVEL
METER
PHASE
1/2 3/4 5/6 7/8
1/2
ANALOG
From
Computer
To
Computer
S/PDIF A DAT
3/4 5/6 7/8 L/R 1-8
9/10 11/12 13/14 15/16 17/18 19/20
ADAT IN
S/PDIF IN
INPUT8
INPUT7
INPUT6
INPUT5
INPUT4
INPUT3
INPUT2
INPUT1
48V
Hi-Z/
Lo-Z
Hi-Z/
Lo-Z
ADAT8
ADAT7
ADAT6
ADAT5
ADAT4
ADAT3
ADAT2
ADAT1
INPUT8
INPUT7
S/PDIF L/R
INPUT6
INPUT5
INPUT4
INPUT3
INPUT2
INPUT1
Gain
AD
AD
AD
AD
AD
AD
AD
AD
Gain
Gain
Gain
Gain
Gain
Gain
Gain
LO CUT PHASE
EFX SEND
LEVEL
METER
DA
DA
DA
DA
DA
DA
DA
DA
DA
DA
PEAK
METER
Loop
Back
L
Loop
Back
R
LoopBack
Switch
LoopBack L
LoopBack R
Page 5
—5—
Setting the Inputs (INPUT)
Showing the digital inputs
Click the DIGITAL button to show the digital inputs.
The screen will open to the right and show S/PDIF and ADAT 1 –
ADAT 8.
Adjusting the input gain
Turn the GAIN knob to adjust the input gain so that it does not
cause the CLIP indicator to light.
NOTE
• If you adjust a GAIN knob, the corresponding
input gain setting will also change automatically.
2. Enable the automatic gain setting.
3. Input the audio signal.
4. Complete the setting.
HINT
• If there is no input for about three seconds, the button will blink
more rapidly and the setting will complete automatically.
Click again
Click
Using phantom power
Click the 48V(1-4) or 48V(5-8) button so that it lights.
When the corresponding switch is lit, phantom power is supplied
to INPUTS 1–4 or INPUTS 5–8 at the same time.
Using the Hi-Z function (INPUTS 1–2 only)
Click the Hi-Z button so that it lights.
Enabling the lo-cut filter
Click the LO CUT button so that it lights.
The cutoff frequency is 80 Hz.
Reversing the polarity
Click the PHASE button so that it lights.
Adjusting the effect level
Adjusting the gain automatically (INPUT 1–8 only)
To set the optimal gain level automatically, click the AUTO button
and input the audio signal.
Setting the automatic gain
1. Select the maximum recording level.
Turn the EFX SEND knob to adjust the effect level.
Double-click to set it to −inf. (See “Adjusting the effect” on P.9.)
Checking input levels
Check the level meters to see the input levels.
If a level exceeds 0 dB (maximum value), the top of the meter will
light red. Click the meter to turn off this indicator.
Page 6
—6—
Checking computer settings/Using the loopback function/Selecting the clock source (COMPUTER)
Sending the mixed signal to the computer
All the inputs and computer inputs can be mixed and sent
back to the computer.
When you want to record the final mixed signal, press the LOOP-
BACK button so that it lights.
NOTE
• The LOOPBACK function only works for the MAIN OUTPUT mixer.
• This signal is sent to the computer as INPUT1 and INPUT2 .
Reversing the phase
Click the PHASE button so that it lights.
Expanding the COMPUTER section
To expand the COMPUTER section, click the DAW3-20 button.
The screen will open to the right and show DAW3/4 – DAW19/20.
Checking the sampling rate
Check the sampling rate.
The lit indicator shows the sampling rate that the is using.
NOTE
When the sampling rate shown is 88.2 or 96, ADAT 5–8 cannot be
used. When it is 176.4 or 192, ADAT 3–8 cannot be used.
Adjusting the effect level
Turn the EFX SEND knob to adjust the effect level.
Double-click to set it to −inf. (See “Adjusting the effect” on P.9.)
Checking input levels from the computer
Check the level meters to see the input levels from the computer.
If a level exceeds 0 dB (maximum value), the top of the meter will
light red.
Click the meter to turn off this indicator.
Setting the clock source
Select the clock source to use for synchronizing signals.
Click the INTERNAL, ADAT, S/PDIF or WORD CLOCK button so
that it lights.
NOTE
If synchronization with an external digital device is not possible, the
CLOCK SOURCE indicator will blink.
In this case, the will operate using its internal clock.
Page 7
—7—
Using the built-in mixer (MIXER)
The mixer can be set separately for each output. (See “ Mixer Block Diagram” on page 4.)
For example, different mixes can be output from the MAIN OUT and the LINE OUT 1/2 outputs.
Changing the output jacks
Muting the input signals
Input signals can be muted.
Click the M button so that it lights to mute the input.
Soloing one input
All inputs other than the selected are muted.
Click the S button so that it lights to solo the channel.
Click an output tab to select it.
If the window is narrow, click to change the shown tabs.
Assigning an output to the HEADPHONE 2 jack
Click the headphone icon on an output tab to assign that output
to the HEADPHONE 2 jack.
NOTE
The MAIN OUT and LINE OUT 1/2–LINE OUT 7/8 can be assigned.
Working with input from S/PDIF and ADAT
Press the INPUT tab DIGITAL button.
The screen will open to the right and show S/PDIF and ADAT 1 – ADAT 8.
Controlling computer channels number 3 and higher
Press the COMPUTER DAW3-20 button.
The screen will open to the right and show DAW3/4 – DAW19/20.
Adjusting the input signal panning
Turn the PAN knob for an input to adjust the panning of that
input signal.
Double-click to set it to 0 (center).
At their center positions, INPUT 1–8 and ADAT 1–8 are reduced −3 dB.
NOTE
If both SOLO and MUTE are enabled at the same time, MUTE takes
priority.
Adjusting the input signal levels
Drag each input fader to adjust its input signal level.
Double-click to set it to 0 dB.
Copying settings from the currently selected
output mixer to another output mixer
You can copy the settings from the currently
selected output mixer to another output mixer.
1. Click the COPY MIX TO button next to the
output tab.
2. Select the output to receive the settings in the
dialog shown, and click the “Copy” button.
Resetting PEAK, SOLO and MUTE for all channels at once
Click the CLEAR PEAKS, CLEAR SOLOS or CLEAR MUTES button
to reset the peak indicators or the solo or mute status for all chan-
nels at once.
Page 8
—8—
Setting Output Levels (OUTPUT)
You can set the output level for the channels selected by the OUTPUT tab.
Checking output levels
You can check the OUTPUT/PHONES level with the level meters.
If a level exceeds 0 dB (maximum value), the top of the meter will
light red.
Click the meter to turn off this indicator.
Adjusting the effect return level
Turn the EFX RETURN knob to adjust the effect return level mixed
into the output.
Double-click to set it to −inf.
(See “Adjusting the effect” on P.9.)
Muting the output signal
You can mute the output.
Click the M button so that it lights to mute the output.
Adjusting the output volume
Drag the fader to adjust the volume.
Page 9
—9—
Using the Effect (EFFECT)
Adjusting the effect
1. Turn the effect on.
Click
2. Select the effect.
Turn
3. Adjust the EFX SEND of each input.
Turn
4. Adjust the EFX RETURN of each output.
Turn
Effect types
ROOM1
ROOM2 This reverb simulates the reverberations of a concert in a club.
HALL1 This reverb simulates a concert hall with bright reverberations.
HALL2 This reverb simulates a concert hall with muted reverberations.
PL ATE1 This simulates a plate reverb with short reflections.
PLATE2 This simulates a plate reverb with long reflections.
ECHO1 This short delay can be used in many situations.
ECHO2 This simulates a tape echo.
NOTE
This reverb simulates the reverberations of an echo chamber in a
recording studio.
• The effect and upsampling functions cannot be used at the
same time. Turning one on will turn the other off.
• If the upsampling function is on, a conrmation message will
appear when the effect is turned on. Click the "Turn the effect
ON" button.
Page 10
—10—
Using the Upsampling Function (UPSAMPLING)
Activating the upsampling function
When the original sampling rate is 44.1 kHz or 48 kHz, internal processing can al-
low operation at 176.4 kHz or 192 kHz.
1. Click the UPSAMPLING button.
Click
This activates the upsampling function.
NOTE
• The upsampling function only works for 44.1/48 kHz.
• The effect and upsampling functions cannot be used at the
same time. Turning one on will turn the other off.
• If the effect function is on, a conrmation message will appear
when upsampling is turned on. Click the "Turn upsampling
ON " button.
Deactivating the upsampling function
1. Click the UPSAMPLING button.
Click
This deactivates the upsampling function.
NOTE
If the effect function is turned on, the upsampling function will be
deactivated.
Page 11
—11—
Saving and Loading Settings (MEMORY)
Saving settings
1. Start saving the settings.
Click
2. Select a blinking button to save the settings.
Click
Saving and Loading Setting Files (SAVE/LOAD)
Loading settings
1. Load saved settings.
Click
Resetting interface settings
To restore a to its factory default
settings, click the FACTORY RESET but-
ton. On the confirmation screen, click
“Reset”.
Settings saved in will not
be reset.
Saving settings
1. Select “Save” from the “File” menu.
NOTE
After saving settings as a file, select "Save as" to save settings
with a different file name.
2. Set the file name and saving location, and save the file.
Loading settings
1. Select “Open…” from the “File” menu.
2. Select the settings file and click “Open”.
The settings will be loaded.
NOTE
Settings saved in the memories will not be changed when a
settings file is loaded.
Page 12
Using the Power Management Function
The power will automatically turn off 10 hours after the is put in standalone mode. You can use to turn this function ON/OFF.
Disabling the power management function
1. Click “File” in the tool bar.
Click
2. Select “Preferences”.
Click
NOTE
On a Mac, open the UAC-8 MixEfx menu, select "Preferences…" and change the
"Enable Power Management function" setting.
3. Remove the check next to “Enable Power Management function”.
HINT
• The power management function is enabled when a check appears next to this
item.
—12—
Page 13
Managing Software and Firmware Versions
Viewing version information
1. Click “File” in the tool bar.
Click
2. Select “About UAC-8 MixEfx”.
Click
3. Check the version information.
Setting version update alerts
1. Click“ File” in the tool bar.
Click
2. Select "Preferences".
Click
3. Enable the version update alerts.
NOTE
On a Mac You can check the version information by opening "UAC-8 MixEfx" in
the menu bar and selecting "About UAC-8 MixEfx".
HINT
• "Version" is the mixer application version and "Device Version" is
NOTE
On a Mac You can set the version update alert by opening "UAC-8 MixEfx" in the
menu bar and selecting "Preferences…"
HINT
• The alerts are enabled when checked.
the version of the hardware.
Windows® is a registered trademark of Microsoft® Corporation.
Mac® is a registered trademark of Apple Inc
ADAT and ADAT Optical are trademarks of inMusic Brands Inc. in the US and other countries.
Note: All trademarks and registered trademarks in this document are for identification purposes only and are not intended to infringe on the copyrights of their respective owners.
ZOOM CORPORATION
4-4-3 Kanda-Surugadai, Chiyoda-ku, Tokyo 101-0062 Japan http://www.zoom.co.jp
Z2I-2359-02
Loading...