Yealink SIP-T19 User Manual

Configuring Your Phone

Configuring via web user interface

Accessing the web user interface:

1. Press when the phone is idle to get the IP address of the phone.

2. Open the web browser on your computer, enter the IP address into the address bar
(e.g., "http://192.168.0.10" or "192.168.0.10") and press Enter.

3. Enter the user name (default: admin) and password (default: admin) in the login page
and click Confirm.

Note: Please locate your computer in the same network segment of the IP phone [phone].X) to access
the web user interface. Contact your system administrator for more information.

Network Settings: Click on Network->Basic->IPv4 Config

You can configure the network in the following ways:

DHCP: By default, the phone attempts to contact a DHCP server in your network to obtain its
valid network settings, e.g., IP address, subnet mask, gateway address and DNS address.

Static IP Address: If the phone cannot contact a DHCP server for any reason, you need to
configure IP address, subnet mask, gateway address, primary DNS address and
secondary DNS address for the phone manually.

PPPoE: If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE
mode. Contact the ITSP for the user name and password.

Note: The wrong network settings may result in inaccessibility of the phone and may have an impact on
the network performance. Contact your system administrator for more information.

Account Settings: Click on Account->Register

Parameters of the account:

Register Status:
Line Active:
Label:
Display Name:
User Name:
Register Name:
Password:
Server Host:

Register status icons on the LCD screen:

It shows the register status of the current account.
You can select Enabled/Disabled to enable/disable the account.
It is shown on the LCD to identify the account.
It is shown as caller ID when placing a call.
It is provided by ITSP for registration (required).
It is an authenticated ID for authentication provided by ITSP (required).
It is provided by ITSP for registration (required).

It is provided by ITSP for registration (required).

Enterprise IP Phone

SIP-T19P & SIP-T19

Registered Register Failed Registering

Note: Check with your system administrator if any error appears during the registration process or a
specific configuration is required for your registration.

Configuring via phone user interface

Network Settings:

Press the Menu soft key when the phone is idle, select Settings->Advanced Settings
(password:admin)->Network->WAN Port/VLAN/Webserver Type/802.1x Settings to configure
the network.

Account Settings:

Press the Menu soft key when the phone is idle, select Settings->Advanced Settings
(password:admin)->Account to configure the account.

Note: For more information on account parameters, refer to Configuring via web user interface.

For more information, refer to the User Guide available online:

http://www.yealink.com/SupportDownloadfiles_detail.aspx?CateId=334&flag=142

Copyright 2014 YEALINK NETWORK TECHNOLOGY CO.,LTD.

c

www.yealink.com

Quick Installation Guide

Applies to firmware version 72.1 or later.

Packaging Contents

The following items are included in your package. If you find anything missing,
contact your system administrator.

2. Connect the handset and optional headset, as shown below:

Handset Cord

IP Phone

Handset

Stand

Assembling the Phone

1. Attach and detach the stand, as shown below:

a) Attach the stand:

Wall Mount Method

b) Detach the stand:

Ethernet Cable

Power Adapter
(Optional)

Desk Mount Method

Quick Installation
Guide & Quick
Reference Guide

Note: The headset should be purchased separately.

3. Connect the network and power, as shown below:

You have two options for network and power connections. Your system administrator will
advise you on which one to use.

PC Connection
(Optional)

Power Adapter
(DC 5V)

A

AC Power Option

B

PoE ( Power over
Ethernet ) Option

PC Connection
(Optional)

IEEE 802.3af compliant
PoE Hub/Switch

Note: PoE is only applicable to the SIP-T19P IP phone. If inline power (PoE) is provided, you don’t need to
connect the power adapter. Make sure the Etherne cable and hub/switch are PoE compliant.

SIP-T19P & SIP-T19 Quick Installation Guide

Startup

After the IP phone is connected to the network and supplied
with power, it automatically begins the initialization process.
After startup, the phone is ready for use. You can configure
the phone via web user interface or phone user interfafce.

Welcome

Initializing... please wait

www.yealink.com