Yamaha MV6, MV12 User Manual

MIXER

Owner’s Manual

Thank you for purchasing the YAMAHA MV12/6 Mixer.
The MV12/6 mixer is designed to provide the user with an ideal balance of
operability, functionality, and simplicity.
In order to get the most out of your MV12/6 mixer and its functions, and to
enjoy years of trouble-free use, please read this Owner’s Manual thoroughly
and keep it in a safe place for future reference.

Keep This Manual For Future Reference.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on
different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

MV12/6 — Owner’s Manual

Important

Read the following before operating the MV12/6

Warnings

• Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects
inside this unit are a fire and electrical shock hazard.

• Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result.

• Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as
marked on the unit. Failure to do so is a fire and electrical shock hazard.

• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a fire and electrical
shock hazard.

• Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire
and electrical shock hazard. In particular, be careful not to place heavy objects on a power cord covered
by a carpet.

• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid gets inside
the unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your dealer for
repair. Using the unit in this condition is a fire and electrical shock hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove the power
plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this
instruction, fire or electrical shock may result.

• If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using
the unit with a damaged power cord is a fire and electrical shock hazard.

• Do not remove the unit’s cover. You could receive an electrical shock. If you think internal inspection,
maintenance, or repair is necessary, contact your dealer.

• Do not modify the unit. Doing so is a fire and electrical shock hazard.

• If lightning begins to occur, turn off the power switch of the unit as soon as possible, and unplug the
power cable plug from the electrical outlet.

• If there is a possibility of lightning, do not touch the power cable plug if it is still connected. Doing so
may be an electrical shock hazard.

Important 1

Cautions

• When rack-mounting the unit, allow enough free space around the unit for normal ventilation. This
should be: 10 cm at the sides, 15 cm behind, and 15 cm above.
For normal ventilation during use, remove the rear of the rack or open a ventilation hole.
If the airflow is not adequate, the unit will heat up inside and may cause a fire.

• Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A damaged
power cord is a potential fire and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

Operating Notes

• Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from
the unit.

• XLR-type connectors are wired as follows:
pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

• The performance of components with moving contacts, such switches, rotary controls, faders, and
connectors, deteriorates over time. The rate of deterioration depends on the operating environment and
is unavoidable. Consult your dealer about replacing defective components.

MV12/6 — Owner’s Manual

2 MV12/6

Features

• The MV12/6 offers 12 input channels that can be mixed into stereo,
monaural, or to four group outputs.

• A MONITOR jack offers easy connection to a sub amp for monitor­ing. It allows monitoring of the main stereo output, TAPE IN input
and the signals from groups 1-2, 3-4.

• The mixer is equipped with a highly efficient, built-in digital effects
section. The built-in effects allow you to create professional sounding
mixes without the need of additional equipment. An EFFECT SEND
jack is also supplied to allow the use of external effectors.

• Two AUX SEND/RETURN jacks are provided. Two separate AUX
buses can be used as sends for external effectors or a monitor system.

• The mixer supplies phantom power to provide easy connection of
condenser microphones that require an external power source.

• The mixer is equipped with INSERT IN, INSERT OUT jacks for
input channels 1-4 allowing individual effects to be inserted into
individual channels.

• Input Channels 1-8 are equipped with XLR type input jacks. A three­way selector switch allows compatibility with a wide range of sources
such as condenser microphones that need an external power source,
regular dynamic microphones, line level devices, etc.
Input Channels 9-12 are equipped with stereo line input jacks

• The main input and output jacks are also equipped with Euro-block
connectors. These connectors facilitate the installation of the mixer
as a permanent fixture in halls, etc.

• TAPE IN jacks and REC OUT jacks offer easy connection of tape
decks for playback and recording.

Contents

Front & Rear Panels ............................ 3

Channel Control Section ........................ 3

Master Control Section .......................... 5

Connector Panel .................................... 7

About the Accessories ...................... 11

Applications .......................................... 12

Supplement .......................................... 14

Specifications ....................................... 14

Dimensions .......................................... 16

Block and Level Diagrams .................... 17

Caution: When the unit is installed in a rack

The main unit’s power switch is located on the rear panel of
the unit. When installed in a rack, please use the external
power switch on a power distributor, etc.

Power distributor, etc.

MV12/6 — Owner’s Manual

Front & Rear Panels

Channel Control Section

Front & Rear Panels 3

Channels 1-8

(Monaural)

Channels 9-12

(Stereo)

q GAIN Control

Adjusts the input level of the signal entering the mixer to an
optimum level.

To obtain an optimum balance between the S/N ratio and

q

dynamic range, adjust the level so that the PEAK Indicator w
occasionally lights.

w

-60 to -16 indicates the MIC input adjustment level, -34 to +10
indicates the LINE input adjustment level.

* The Input Select Switch located on the Connector Panel provides

settings for the type of mic or device that is connected to the INPUT
jack (refer to page 7).

e

w PEAK Indicator

The indicator detects peaks in the signal after it has passed the
EQ.

The indicator will light red when the level reaches +17dB to
warn that clipping is imminent.

rr
tt

e Equalizer

Provides +/-15dB of control over high, mid and low frequency
ranges at the center frequencies listed below.

HIGH : 10kHz (shelving)
MID : 2.5 kHz (peaking)

y

LOW : 100Hz (shelving)

Frequency response will be flat when the knob is positioned at
“G”.

u

ii

+20

+15

+10

+5

0

–5

Response [dB]

–10

–15

–20

r AUX1, AUX2 Controls
t POST Switch

o

Individually controls the level of the signal sent from each
channel to the AUX1 and AUX2 buses.

The signal taken from before the channel fader is sent to
AUX1.

Depending upon the POST switch setting, the signal taken
from either before (POST Switch = ?) or after (POST Switch
= >) the channel fader is sent to AUX2.

When a stereo channel is used, L and R signals are combined
and sent to the AUX1 and AUX2 buses.

Frequency [Hz]

10k1k100 20k20

MV12/6 — Owner’s Manual

4 Front & Rear Panels

y EFFECT Control

Controls the level of the signal sent from each channel to the EFFECT bus.
This control is located after the channel fader so its level will also be affected by the channel fader

setting.
When a stereo channel is used, L and R channel signals are combined and sent to the EFFECT bus.

u PAN Control (CH1-8)

BAL Control (CH9-12)

The PAN control knobs set the position within the stereo field of each signal that is sent to the GROUP
bus 1-2, GROUP bus 3-4 and STEREO bus L-R.

The BAL control knobs set the balance between left and right channels and assigns the signals that are
received at INPUT L (CH9, 11) to GROUP buses 1/3 or STEREO bus L, and the signals received at
INPUT R (CH10, 12) to GROUP buses 2/4 or STEREO bus R.

i GROUP, ST Select Switches

Used to send the signal of each channel to the GROUP bus 1-2, GROUP bus 3-4 and STEREO bus L-R.
When the switch is ON (>), the signal is sent to the relative bus.

o Channel Fader

Controls the output level of the input channel signal and adjusts the volume balance between channels.

* Levels of unused faders should be lowered.

CH INPUT

1~4ch

CH INPUT

5~8ch

INPUT

[-60~+10dB]

INSERT OUT

[0dB]

INSERT IN

[0dB]

INPUT

[-60~+10dB]

ST INPUT

9/10ch, 11/12ch
[-34~+10dB]

MIC(+48V)
MIC
LINE

HA

PAD

GAIN

[-60dB~-16dB]
[-34dB~+10dB]

BA

MIC(+48V)

MIC
LINE

PAD

HA

GAIN

[-60dB~-16dB]
[-34dB~+10dB]

[0dB]

HA

L

R

GAIN

[-34dB~+10dB]

HA

[0dB]

[0dB]

3-Stage EQ

Lo

Mid

3-Stage EQ

+48V

3-Stage EQ

Lo

+48V

3-Stage EQ

Lo

Hi

Mid

Mid

PEAK

Hi

Hi

PEAK

Ch.Fader

[-10dB]

PEAK

Ch.Fader

[-10dB]

BA

ST Ch.Fader

[-10dB]

BA

SUM

[0dB]

POST

POST

[0dB]

1-2

3-4

ST

[-6dB]

AUX1

AUX2

EFFECT

[0dB]
1-2

3-4

ST

[-6dB]

AUX1

AUX2

EFFECT

1-2

3-4

ST

[-6dB]

AUX1

AUX2

EFFECT

PAN

[0dB]

BA

PAN

[0dB]

BA

[0dB]

BAL

POST

GROUP2

GROUP3

GROUP1

STEREO L

GROUP4

AUX2

STEREO R

AUX1

EFFECT

MV12/6 — Owner’s Manual