Whirlpool KUDE20FX, KUDE40FX, KUDC10IX, KUDC10FX, KUDE20IX User Manual
...
|
|
® |
Undercounter Dishwasher |
||||
|
|
||||||
PRODUCT MODEL NUMBERS |
|
|
PRODUCT DIMENSIONS |
||||
|
|
|
|
|
|
|
|
KUDC10FX |
|
KUDE60SX |
|||||
KUDC10IX |
|
KUDE70FX |
|
|
|||
|
|
||||||
KUDE20FX |
|
KUDL15FX |
|
|
|||
KUDE20IX |
|
KUDS30CX |
|
|
|||
KUDE40FX |
|
KUDS30FX |
|
|
|||
KUDE48FX |
|
KUDS30IX |
|
|
|||
|
|
||||||
KUDE50CX |
|
KUDS30SX |
|||||
KUDE60FX |
|
KUDS35FX |
|||||
KUDE60HX |
|
|
|
|
|
|
|
Electrical Requirements: 120-volt, 60-Hz, AC-only, 15or 20-amp. fuesd electrical supply. Copper wire only. A timedelay fuse or circuit breaker and separate circuit is recommended.
If direct wiring dishwasher: Use flexible, armored or nonmetallic, sheathed copper
wire with grounding wire that 
meets the wiring requirements for 
your home and local codes and ordinances.
Use a U.L.-listed or CSA-approved conduit connector.
If connecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part
No. 4317824) marked for use with 
dishwashers. Follow the kit
instructions for installing the power supply cord.
Power supply cord must plug into a grounded three-prong, outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.
Water Supply Requirements: A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure. Water temperature must be 120°F (49°C) water at dishwasher. Use ³⁄ " O.D. copper tubing with compression fitting or flexible braided water supply line (¹⁄ " minimum plastic tubing is not recommended). Use a 90° elbow with ³⁄ " N.P.T. external pipe threads on one end. Do not solder within 6" (15.2 cm) from water inlet valve.
Drain Requirements: A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part No. 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.
Make sure to connect the drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended
that the drain hose either be
looped up and securely
fastened to the underside of
the counter, or be connected
to an air gap.
Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or
floor.
Use ¹⁄ " (1.3 cm) minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance with the air gap installation instructions. When connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation |
W10321621-D-KA |
Instructions packed with product. Specifications subject to change without notice. |
6/15/11 |
Loading...