Owner’s Manual
LED Outdoor Lighting Fixture
Installation Instructions
W-373 120513
Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE
Congratulations on yourWestinghouse purchase. This fixture has been designed to give you many years ofbeautyand service. For questions and comments, please visit www.westinghouselighting. com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improper installation, surges in electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or replace the fixture or refund the purchase price.
WARNING:
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.
CAUTION: “This fixture employs a grounded type receptacle and is not intended for connection to a two wire ungrounded source of supply.”
2
FIGURE 1.
|
CROSS |
|
*OUTLET |
BAR (B) |
|
BOX (C) |
|
|
|
SIDE |
*OUTLET BOX |
|
HOLE (G) |
SCREWS (D) |
|
|
MOUNTING |
|
|
SCREWS (A) |
|
|
BACK PLATE (H) |
GROUND
WIRE
GREEN
GROUNDING
SCREW (F)
WIRE
CONNECTORS (E)
CAP NUTS (I)
Line art shown may not exactly match the fixture enclosed. |
*NOT SUPPLIED |
|
However, the installation instructions do apply to this fixture. |
||
|
3
MOUNTING AND WIRING INSTRUCTIONS
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking.
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.
1.Turn off power at fuse box to avoid possible electric shock.
2.Thread mounting screws (A) into cross bar (B) with mounting screws protruding away from outlet box (C) (see figure 1).
3.Secure cross bar (B) to outlet box (C) with outlet box screws (D) (not included).
4.Identify color coding of fixture wires (see figure 2 on page 11).
5.To connect wires, take black fixture wire and place evenly against black outlet box wire. Do not twist wires.
6. Fit wire connector (E) over wires and twist until there is a firm connection (see figure 2).
7.Repeat steps 4 and 5 with the white (group B from figure 2) fixture wire and outlet box wires.
8.Partially thread green grounding screw (F) into side hole (G) of cross bar (B) (see figure 1).
9.Wrap ground wire from fixture around green grounding screw (F) leaving enough excess wire to then connect ground wire and outlet box wire with wire connector (E), if applicable.
10.Tighten grounding screw (F). Do not over tighten.
FIXTURE ASSEMBLY INSTRUCTIONS
1.Tuck wires inside outlet box (C) (see figure 1).
2.Place back plate (H) over mounting screws (A).
3.Secure into place with cap nuts (I).
4.Turn on power at circuit breaker.
4
Loading...