|
Contents |
Safety and warnings....................................................................................... |
2-3 |
Introduction..................................................................................................... |
4 |
Stand installation guide..................................................................................... |
5 |
Installation................................................................................................... |
6-9 |
Remote Control.............................................................................................. |
10 |
Power Connection...................................................................................... |
11-14 |
Setup Menus.............................................................................................. |
15-39 |
-1-
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
1)Read these instructions.
2)Keep these instructions.
3)Heed all warnings.
4)Follow all instructions.
5)Do not use this Television near water.
6)Clean only with dry cloth.
7)Do not block any ventilation openings, install in accordance with the instructions.
8)Do not install near any heat sources such as radiations, heat registers, stoves, or other Television (including amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10)Protected the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the Television.
11)Only use attachments/accessories specified by the manufacturer.
12)Unplug this Television during lighting storms or when unused for long periods of time.
13)Refer all servicing to qualified service personnel. Servicing is required when the Television has been damaged in any way, such as; power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the Television, the Television has been exposed to rain or moisture, does not operate normally, or has been dropped.
14)Mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
15)The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloth, curtains, etc.
16)No naked flame sources, such as lighted candles, should be placed on the Television.
17)Attention should be drawn to the environmental aspects of battery disposal.
18)The use of Television in moderate climate.
19)The Television shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the Television.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The symbol indicates that dangerous voltages constituting a risk of electric shock are present within this unit.
The symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
WARNING:
To reduce the risk of fire or electric shock, do not expose this Television to rain or moisture.
WARNING:
The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING:
The excessive sound pressure from earphones and headphones can cause hearing loss.
This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
This Westinghouse product has earned the ENERGY STAR® for meeting U.S. Federal energy efficiency guidelines as set by the Department of Energy and Environmental Protection agency. The ENERGY STAR® program exists to provide energy saving guidelines and help promote energy efficient products and practices. Changes to certain features, settings and functions of this TV can change and/or increase its power consumption. Depending on how settings are changed, power consumption may exceed the limits required for ENERGY STAR® qualification.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television receiver. Do not open the cabinet.
Refer servicing to qualified service personnel.
To prevent fire or electrical shock hazard, do not expose the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver.
Do not block the ventilation holes on the back cover of the TV. Adequate ventilation is essential to prevent failure of electrical components.
Do not trap the power supply cord under the television receiver's stand.
Never stand on, lean on, or suddenly push the television or its stand. You should pay special attention to children. Serious injury may result if it falls.
Do not place your television on an unstable cart, stand, shelf or table. Serious injury to an individual and/or damage to the television may result if it falls.
When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight and other sources of heat. Do not stand the television receiver directly on other products which give off heat, e.g. video cassette players and audio amplifiers. Do not place naked flame sources, such as lighted candles on or near the television.
If the television is to be built into a compartment or similar enclosure, the minimum distances must be maintained. Heat build-up can reduce the life of your television, and can also be dangerous.
-3-
INTRODUCTION
Main features |
Accessories |
■Integrated ATSC TV tuner for HDTV broadcast reception
■High brightness provides a vivid and brilliant picture
■Deeper blacks and brighter whites with high contrast
■Wide Screen aspect ratio (16:9) for a complete home theater experience
■HDMI input for true digital connection
■VGA port for connection to PC
■Built-in stereo speaker system
■Full-function Remote Control
Power cable................................... |
1 |
Infrared Remote Control.................... |
1 |
User’s Manual ................................. |
1 |
Battery(AAA)................................... |
2 |
Main parameter
Viewing Picture Size (diagonal) |
24 inches |
|
|
|
|
Resolution: |
1366 x 768 |
|
|
|
|
Power supply |
AC 100-240V 50/60Hz |
|
Power consumption |
40W |
|
|
|
|
Audio Output Power (THD 7%): |
2x3W |
|
|
|
|
Aspect Ratio: |
16:9 |
|
|
|
|
TV System: |
ATSC Digital system and NTSC Analog system |
|
Video Signal System: |
NTSC |
|
|
|
|
Receiving Channel: |
Cable :1-135/ Air: 2-69 (ATV&DTV) |
|
|
|
|
High-Definition Multimedia Interface (HDMI) Input |
x 2 |
|
|
|
|
YCb(Pb)Cr(Pr) Input |
x 1 |
|
|
|
|
Composite Video Input |
x 1 |
|
|
|
|
Analog RGB (VGA) Input |
x 1 |
|
|
|
|
Audio Input |
x 2 |
|
|
|
|
Headphone Output |
x 1 |
|
|
|
|
SPDIF Output |
x 1 |
|
|
|
|
Horizontal definition (TV line) |
Composite Video Input |
>=350 |
|
Video Input |
>=400 |
|
YCb(Pb)Cr(Pr) |
>=400 |
|
|
|
-4-
Base Stand Assembly Instruction
1. Place the TV with the display side down on a flat surface. Use a cloth to protect the display. Position the stand base plate onto the bottom of the stand pole.
2. Attach the stand base plate to the stand pole by firmly tightening the supplied screw.
-5-
INSTALLATION
Front panel |
Side panel |
|||
|
|
|
|
|
|
|
|
|
|
3
1
2
30 30
1:Remote control sensor.
2:Indicator LED: BLUE POWER ON.
RED STANDBY.
3:Side panel keys
SOURCE |
1 |
|
MENU |
2 |
|
CH+ |
3 |
|
CH- |
||
|
||
VOL+ |
4 |
|
VOL- |
||
|
||
STANDBY |
5 |
1.SOURCE: Display the input source menu.
2.MENU: Display main MENU.
3.CH+/CH-: In TV mode, press "CH+" or "CH-" to change the channel up and down. In MENU mode, press "CH+" or "CH-" to select items in standby mode, press "CH+" or "CH-" to turn on the TV.
4.VOL+/VOL-: Adjust sound level. In MENU mode, press "VOL+ " or "VOL- " to adjust the item that you selected.
5.STANDBY: Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to STANDBY.
REAR Connections
Y |
Pb |
Pr |
|
VIDEO |
L |
R |
SPDIF |
All the terminals are (from left to right):
YPbPr INPUT,VIDEO, AUDIO INPUT, SPDIF OUTPUT.
Note: AV and YPbPr share one audio channel.
SIDE Connections
All the terminals are (from left to right):
USB, HDMI2, HDMI1, HEADPHONE, PC AUDIO, VGA, RF.
Note: 1. When HDMI has an input signal coming from a DVI source then the audio input signal must be connected to the PC audio input.
2. The USB port can be used for JPEG Images, Motion-JPEG videos, or upgrading software.
-6-
INSTALLATION
ANTENNA
Note:
Aerial connections: IEC (female).
Input impendance:75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are set to
Power off.
1.Connect VGA and audio cable. 2.Connect the power cord.
3.Power on the TV, switch to PC mode. 4.Power on the PC.
This sequence is very important.
-7-
INSTALLATION
PC
PRESET MODE
|
RESOLUTION |
V.Freq.(Hz) |
H.Freq.(KHz) |
1 |
720*400 |
70 |
31.47 |
2 |
640*480 |
60 |
31.47 |
3 |
640*480 |
75 |
37.50 |
4 |
800*600 |
60 |
37.88 |
5 |
800*600 |
75 |
46.88 |
|
|
|
|
6 |
1024*768 |
60 |
48.36 |
|
|
|
|
7 |
1024*768 |
70 |
56.48 |
8 |
1024*768 |
75 |
60.02 |
9 |
1280*1024 |
60 |
63.98 |
|
|
|
|
10 |
1280*1024 |
75 |
80.00 |
|
|
|
|
11 |
1366*768 |
60 |
75.50 |
|
|
|
|
-8-
INSTALLATION
AV EQUIPMENT
You can use the input terminals on TV set rear as follows.
HDMI |
VIDEO EQUIPMENT with YPbPr
G B |
R |
W R |
|
|
Y Yellow (video)
W White(audio L)
R Red(audio R or Pr)
B Blue(Pb)
G Green(Y)
G B R
W |
R |
|
|
Y |
Pb |
Pr |
|
|
|
VIDEO |
L |
R |
SPDIF |
|
|
|
W |
|
R |
VIDEO EQUIPMENT |
|
|
|
||
W |
R |
TO VIDEO |
|
|
|
|
|
OUTPUTS |
|
|
|
TO AUDIO OUTPUTS |
|
|
|
|
|
The television's inputs can be connected to the following types of equipment: VCR, multi disc player,
DVD, camcorder, video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i.
-9-
REMOTE CONTROL
1:POWER
To turn the TV on.
2:NUMBER KEY
For direct access to channels.
3:
Displays the main on-screen menu.
4:CURSOR
To move within the menu.
5:EXIT
To exit the menu.
6:VOL+/-
To adjust sound level.
7:P.M
To switch picture mode.
8:
Press to display and select the available video sources.
9:MUTE
To disable or enable the sound.
10:RECALL
To access the previously viewed channel.
11:ENTER
Confirms selection.
12:TV DISPLAY
Displays/removes the program information
13:S.M
To switch sound mode.
14:CH+/CH-
To access the next or previous channel.
15:ASPECT
To change picture aspect .
16:CH LIST
To display the channel list.
17:EPG
To display all the information of DTV programs.
18:FAV
To circle access your favorite channels in digital TV mode.
19:HDMI
Hot key to go directly to HDMI source.
20:AV
Hot key to go directly to AV source.
21:DTV STRENGTH
To display the DTV signal strength menu.
22:TV
Hot key to go directly to TV source.
23:YPbPr
Hot key to go directly to YPbPr source.
24:CC
To enable or disable the CC function.
25:VGA
Hot key to go directly to VGA source.
26:MTS
To switch the sound stereo.
27:COLOR KEYS
To access or save a favorite channel.
-10-
POWER CONNECTION
Select Language
Welcome to the Westinghouse HDTV
Setup Wizard.
Follow this guide to help setup your HDTV
for scanning channels or accessing your
external devices for cable, satellite, Bul- English
ray, DVD,and gamming.
French
Spanish
Use the ▼▲ arrows on your remote control to select the language to use for menus and message screens.
▼▲ :Select ENTER : Confirm
Power On Mode
Use the ▼▲ arrows on your remote control to select power on mode.
Home optimizes the video settings for Energy
Star qualification.
Retail optimizes the video setting for use on a |
Retail |
retail showroom floor or demo environment. |
|
Go Back
▼▲ :Select ENTER : Confirm
Let’s Get Connected...
Click here to connect a Cable Box or Satellite Box
Click here to connect a Game, Blu-Ray,DVD,or other player
Go Back
▼▲ :Select ENTER : Confirm
-11-
POWER CONNECTION
Scan Channels from the Antenna or coaxial cable input
Use the ▼▲ arrows on your remote control to select the channel scan type.
Cable
Go Back
▼▲ :Select ENTER : Confirm
Antenna[ATSC] Channel Access
Antenna users need a Channel Access Code in order to perform a channel scan and receive broadcast signals.
Contact Westinghouse’s Channel Access Service by: Web:www.westinghousedigital.com/support;
select Channel Access and enter Access Info Text Message: Text Tuner to 95495
Phone: 1-800-701-0680 follow instructions
Select Next to obtain the Access code.
Go Back
:Select ENTER : Confirm
Antenna[ATSC] Channel Access Information
To access channel scan you will need the following Access
Information:
Model: LD-3237
Serial NO.: xxxxxxxxxxxxx
Channel Scan Type: ATSC
Provide these items to Westinghouse’s Channel Access Service by web,text,or phone to obtain an Access Code,then select Next to input access code.
Go Back
:Select ENTER : Confirm
Enter Channel Access Code
Using your remote control to enter the 5 digit access code provided by the channel access service.
Go Back
|
0-9: Key in password |
ENTER : Confirm |
|
Scanning Channels |
|
||
Progress Bar |
|
||
Channels Found |
|
||
Analog: |
0 |
Signal |
|
Digital: |
0 |
||
|
Menu: Exit Scan
-12-