VTech CS6309 User Manual

User’s manual

Accessory handset for
use with VTech models
CS6328-2/CS6328-3/
CS6328-4/CS6328-5/
CS6319/CS6319-2/
CS6319-3/CS6319-4/
CS6329/CS6329-2/
CS6329-3/CS6329-4/
CS6329-5

Model: CS6309

Congratulations

T

Compatible with

Hearing Aid T-Coil

TIA-1083

on purchasing your new VTech product. Before using this
telephone, please read the Important safety instructions on
page 9 of this manual.

This manual has all the feature operations and troubleshooting
necessary to install and operate your new VTech telephone.
Please review this manual thoroughly to ensure proper
installation and operation of this innovative and feature rich
VTech product. For support, shopping, and everything new at
VTech, visit our website at www.vtechphones.com.

please visit www.vtechcanada.com.

The ENERGY STAR® program (www.energystar.
gov) recognizes and encourages the use of
products that save energy and help protect our
environment. We are proud to mark this product
with the ENERGY STAR® label indicating it meets

the latest energy efciency guidelines.

Telephones identied with this logo have reduced

noise and interference when used with most T-coil
equipped hearing aids and cochlear implants. The
TIA-1083 Compliant Logo is a trademark of the
Telecommunications Industr y Association. Used
under license.

In Canada,

Table of contents

Getting started .............................. 1

Parts checklist .................................1

Battery installation .......................... 2

Battery charging .............................. 3

Add and register a handset ............. 4

Replace a handset ..........................5

Handset layout ................................ 6

Appendix ........................................ 8

Battery .............................................8

Important safety instructions ........... 9

Precautions for users of

implanted cardiac pacemakers .. 10

Operating range ............................ 10

Maintenance .................................. 11

About cordless telephones............ 12

The RBRC® seal ............................ 13

Warranty ........................................ 14

FCC, ACTA and IC regulations ..... 16

Technical specications ................ 18

i

Getting started

Parts checklist

Your telephone contains the following items. Save your sales
receipt and original packaging in the event warranty service
is necessary.

Battery

Charg er and power adapter

To purchase replacement batteries or power adapters,
visit our website at www.vtechphones.com or call
1 [phone]. In Canada, go to www.vtechcanada.com
or dial 1 [phone].

Battery
compar tment c over

User’s m anual

1

Handset

Getting started

Battery installation

Install the battery as shown below.

If the battery compartment cover is on the handset,

1.

press on the indentation and slide the cover to remove.
Plug the battery connector securely into the socket

2.

inside the handset battery compartment, matching the
color-coded label.

3.

Place the battery with the label THIS SIDE UP facing up
and the wires inside the battery compartment.

4.

Align the cover at against the battery compartment,

then slide it towards the center of the handset until it clicks
into place.

Charge the handset by placing it in the telephone base or

5.

charger. The CHARGE light is on when the handset charges.

1

2

3

4

CHARGE
light

If the handset will not be used for a long time, disconnect

•
and remove the battery to prevent possible leakage.

To purchase replacement batteries, visit our website at

•
www.vtechphones.com or call 1 [phone]. In
Canada, go to w ww.vtechcanada.com or dial
1 [phone].

5

2

Getting started

Battery charging

Once you have installed the battery, the screen indicates the
battery status (see the table below). If necessary, place the
handset in the telephone base or charger to charge the
battery. For best performance, keep the handset in the
telephone base or charger when not in use. The battery is fully
charged after 16 hours of continuous charging. See the table
on page 8 for battery operating times.

If the screen is blank, you need to charge the handset without
interruption for at least 10 minutes to give the handset enough

charge to use the telephone for a short time. When the battery
is low, the handset beeps four times every minute, shows
LOW BATTERY and a ashing icon. If you are on a call
in low battery mode, the handset has four short beeps to
alert you.

The following table summarizes the battery charge indicators
and actions to take.

Battery indicators Battery status Action

The screen is blank. Battery has no

The screen shows

PLACE IN CHARGER

and ashes.

The screen shows
LOW BATTERY and

ashes. The handset

beeps four times every
minute.

The screen shows
HANDSET X.

charge and the
handset cannot be
used.

Battery has very
little charge and
the handset cannot
be used.

Battery has enough
charge to be used
for a short time.

Battery is charged. To keep the battery

Charge without
interruption (at least
10 minutes).

Charge without
interruption (at least
four minutes).

Charge

without
interruption
the screen shows
HANDSET X (about
30 minutes).

charged, place it in
the telephone base
or charger when not
in use.

until

If you do not plug in the battery into the handset and place it in the
telephone base or charger, the screen displays NO BATTERY.

3

Getting started

Add and register a handset

Each newly purchased handset (CS6309) must be registered

to the telephone base before use. When rst purchased,

each handset shows 1.PRESS FIND HS ON BASE 4 SEC
and 2.THEN PRESS # ON HANDSET alternately. You
may need to charge the handset before registering to the
telephone base. For more details on battery charging, see
page 3.

To make registration easier, read all the instructions on this
page before you begin.

To register a handset:

1.

Place the unregistered handset in the
telephone base. If 1.

ON BASE 4 SEC and 2.THEN PRESS #
ON HANDSET

on the handset screen after a few
seconds, remove the handset and place it
in the telephone base or charger again.

2.

On the telephone base, press and hold

/FIND HANDSET for about four seconds

(until the red IN USE light on the
telephone base turns on) and then
release the button.

3.

Remove the handset from the telephone
base or charger. Press # and the handset
displays REGISTERING...PLEASE WAIT. It takes about
10 seconds to complete the registration. The handset
shows HANDSET REGISTERED and you hear a beep
when the registration completes.

When the registration is complete, the newly registered
handset is assigned the next available handset registration
number. For instance, if you already have HANDSET 1, the
next registered handset will be HANDSET 2.

If the registration fails, the handset shows 1.PRESS FIND

•

HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET
alternately. To reset the handset, remove the handset from
the telephone base and place it back in. Try the registration
process again.

You cannot register a handset if any other system handset

•
is in use.

Only one handset set can be registered at a time.

•

PRESS FIND HS

do not appear alternately

4