VTech CS6129 User Manual
Quick start guide
for models CS6128-31/CS6129/
CS6129-2/CS6129-3/CS6129-4/
CS6129-31/CS6129-32/CS6129-41/
CS6129-52/CS6129-54
Install the telephone base and
charger(s)
Install the telephone base and charger(s) as
shown below.
Telephone
wall jack
DSL lter (not
included) required
if you have DSL
high-speed
Internet service
Telephone line cord
Telephone base
Telephone base
power adapter
(large)
Electrical outlet
not controlled
by a wall switch
NOTES:
Use only the power adapter(s) and
1.
battery(ies) supplied with your VTech
telephone.
For complete feature instructions,
2.
please refer to your user’s manual.
Charger
adapter
(small)
Charger
Batte r y i nst a l l a t i on a nd
charging
Install the battery as shown below. After
installing the battery, you might be able
to make and receive short calls. For best
performance, charge the handset battery for
at least 16 hours before use.
1
If the batter y
compartment cover is on
the handset, press the
indentation and slide the
cover to remove.
3
Place the battery with
the label THIS SIDE
UP
facing up and the
wires inside the battery
compartment.
5
Charge the handset by
placing it in the telephone
base or charger. The
CHARGE light will be
on when the handset is
charging.
2
Plug the battery securely
into the plug inside
the handset battery
compartment, matching
the color-coded label.
4
Align the cover at
against the battery
compartment, then slide
it upwards until it clicks
into place.
CHARGE light
Make, answer and end a call
Make a call
Press /FLASH or .
1.
Dial the number.
2.
-OR-
Dial the number.
1.
Press /FLASH or .
2.
Answer a call
Press /FLASH, or any of the dialing
•
keys (0-9, #, *).
End a call
Press OFF/CLEAR or put the handset in
•
the telephone base or charger.
Activate the answering system
The answering system must be turned on
to answer and record messages. Press
ANS ON/OFF to turn the answering system
on or off. When the answering system is
turned on, it will announce “Calls will be
answered,” and the ANS ON/OFF light will be
on. When the answering system is turned off,
it will announce “Calls will not be answered,”
and the ANS ON/OFF light will be off.
Outgoing announcement
The telephone is preset with a greeting that
answers calls with “Hello, please leave a
message after the tone.” You can use this
preset announcement, or replace it with
your own.
To record your own announcement:
Press ANNC while the telephone is not
1.
in use and the system will announce
“Announcement. Press PL AY or press
RECORD.”
Pr e s s R E C O R D a n d t h e sy st e m
2.
announces, “Record after the tone. Press
STOP when you are done.”
Aft e r th e tone, sp e ak toward s th e
3.
micr o pho n e at the bot tom front of
the telephone base from about nine
inches away.
Press /PLAY/STOP when nished.
4.
The answering system will automatically
5.
play the newly recorded announcement.
Press /PLAY/STOP to stop the playback
at anytime.
To play messages:
Press /PLAY/STOP to play messages
•
and stop playback.
Press X/DELETE while a message is
•
playing to delete it.
Pre ss /S K I P to sk ip to t h e n ex t
•
message.
Press /REPEAT to repeat the current
•
message.
Press VOL / to raise or lower playback
•
volume.
IMPORTANT!
If your product is not working properly:
Refer to the Troubleshooting section of
•
the user’s manual.
Visit our website at www.vtechphones.
•
com or call 1 (800) 595-9511. In Canada,
go to www.vtechcanada.com or dial
1 (800) 267-7377.
96-006860-030-100
Loading...