Ubiquiti UniFi ULED-AC Quick Start Manual

LED

LED Panel with
PoE+ Technology

Model: ULED-AT

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®LED

Panel. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.

Package Contents

LED

LED Panel with
PoE+ Technology

Model: ULP2PE

UniFi LED Panel Quick Start Guide

System Requirements

• An 802.3at-compliant network switch

• UniFi Enterprise of Things (EoT) mobile app software

• Mobile device: iOS 10 or Android 5.0

• UniFi EoT Controller Software

• Computer: Linux, MacOSX, or Microsoft Windows 7/8/10

• Web Browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Dimmer (model UDIM-AT)

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is
designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and
Dynamic Frequency Selection (DFS) requirements.

Network Topology Requirements

There are three ways to control the UniFi LED Panel:

UniFi Dimmer Users in the immediate vicinity control the

UniFi LED Panel using the UniFi Dimmer.

UniFi EoT App over Layer 2 Network A local user runs the

app to connect to a UniFi AP on the same Layer 2 network as
the UniFi LED Panel.

UniFi EoT Controller over Layer 2 Network Alocal user runs

the EoT Controller software on the same Layer 2 network as
the UniFi LED Panel.

UniFi PoE Switch

USG-PRO-4
(DHCP Server)

Internet

LAN

WAN

UAP-AC-PRO

UDIM-AT

UniFi EoT

App

25W 802.3at PoE+

ULED-AT

UniFi Application Server*

OR

UniFi Cloud Key*

UniFi EoT

Controller

Sample Network Diagram

* Available starting with production version of ULED-AT (beta version requires

local installation of the EoT Controller).

Network topology requirements are as follows:

• DHCP-enabled network (for the UniFi LED Panel to obtain

an IP address)

• For UniFi Dimmer only:

A UniFi Dimmer connected to the same Layer 2 network as
the UniFi LED Panel

• For EoT Controller Software:
A UniFi Cloud Key* or UniFi Application Server* running the

UniFi EoT Controller software and connected to the same
Layer 2 network as the UniFi LED Panel

• For EoT App only:
A UniFi AP connected to the same Layer 2 network as the
UniFi LED Panel

* Available starting with production version of ULED-AT (beta version

requires local installation of the EoT Controller).

*640-00332-02*

640-00332-02

Hardware Overview

RESET

Status LED ResetPoE+

LED

LED Color Status

Flashing White Initializing.

Steady White Factory default, waiting for adoption.

Alternating

White/Blue

Firmware upgrade is taking place.

Steady Blue Adopted/System ready.

Port

PoE+ The PoE+ port is a 10/100 Ethernet port used to connect

the power and should be connected to the LAN. Power is
provided by a UniFi Switch with PoE+.

Note: The PoE+ port requires 25W of power, which can

be supplied by an 802.3at-compliant UniFi Switch.

Button

Reset The Reset button serves two functions for the UniFi

LED Panel:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.

Installation

To install and configure the UniFi LED Panel:

1. Connect one end of an Ethernet cable to the PoE+ port on

the back of the UniFi LED Panel.

RESET

2. Connect the other end of the cable to an 802.3at-compliant

switch port that can provide 25W PoE+.

3. Lift the panel and seat it in an opening in the ceiling grid.