TP-Link TL-SM5110-SR, TL-SM5110-LR Installation Guide

Page 1

Installation Guide

10GBase SFP+ LC Transceiver

1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.

2. Insert the transceiver into the slot and rmly press it into place.

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides,

welcome to email techwriter@tp-link.com.cn.

Remove the TransceiverInstall the Transceiver

1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.

2. Disconnect the network ber-optic cables from the transceiver.

3. Remove the protective dust plug from the transceiver.

4. Plug ber-optic cables into the transceiver. Note that the transceiver works without any additional conguration.

Note:

1. Do not touch the output pins on the transceiver with your hand.

2. Always keep the protective dust plug on the transceiver’s optical bores until you are ready to make a connection.

Caution: DO NOT point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.

3. Pull the safety latch downwards to release the transceiver, and then

pull it out from the slot.

4. Reinstall the protective dust plug in the transceiver’s optical bores and place it on antistatic mat or a static shielding bag.

Page 2

Connection

Only use the same transceiver model between switches for fast and reliable connectivity.

For simplicity, we will take SM-5110-SR as an example.

Switch Switch

Specications

General Specications

Normal

Wave Length

Standards and Protocols

Cable

Max. Cable Length

Data Rate

Port Type

Power Support

Safety & Emission

DDM

SFP+ MSA

Hot Swappable

TL-SM5110-SR

850 nm

IEEE 802.3ae TCP/IP

SFF-8472

50/125 or 62.5/125 μm Multi-mode Fiber

300 m (OM3)

10 Gbps

LC Duplex

3.3 V

FCC, CE

Ye s

TL-SM5110-SR

TL-SM5110-LR

1310 nm

9/125 μm Single-mode Fiber

10 km

TL-SM5110-SR

Fiber

Environmental and Physical Specications

Product Operating Temperature 0˚C to 70˚C (32˚F to 158˚F)

Storage Temperature -40˚C to 85˚C (-40˚F to 185˚F)

Operating Humidity 10% to 90% RH, Non-condensing

Storage Humidity 5% to 90% RH, Non-condensing

TP-Link Compatible Products

TP-Link Switches with 10G SFP+ Slots TX432

Note: The transceiver may be incompatible with other vendors’ devices. We recommend that you use only TP-Link transceivers on your TP-Link devices.

Safety Information

Keep the device away from water, re, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Avoid using this product during an electrical storm. There may be a remote risk

of electric shock from lightning.

Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

Page 3

FCC compliance information statement

Product Name: 10GBase SFP+ LC Transceiver Model Number: TL-SM5110-SR/TL-SM5110-LR Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2020/10/12

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A

BSMI Notice

安全諮詢及注意事項請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。注意防潮，請勿將水或其他液體潑灑到本產品上。插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。

此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。

限用物質含有情況標示聲明書

限用物質及其化學符號

汞

鎘

產品元件名稱

PCB

外殼

備考： "○"系指該項限用物質之百分比含量未超出百分比含量基準值。

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product.

鉛

○

CE Mark Warning

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

六價鉻

○

多溴聯苯

PBB

○

多

溴二苯醚

PBDE

○