Tp-link TL-SG108PE User Manual

Installation Guide

8-Port Gigabit Easy Smart Switch with 4-Port PoE

TL-SG108PE

Connection

7106506309 REV1.0.2

For more information, please visit our website: http://www.tp-link.com

DC Power Adapter

AC Power Cord

Ethernet Ports (1-8)

PoE Ports (1-4)

PoE Devices

IP Camera AP IP Phone

Note:

Configuration

The switch is plug and play. To manage the switch, you can use the Web-based GUI or the conﬁguration utility. The utility is provided on the resource CD and only supported on Windows now.

Using the Web-based GUI

Prepare your computer with a static IP address 192.168.0.x ("x" ranges from

1. 2 to 254), and a subnet mask 255.255.255.0.

Visit the Web-based GUI with the default IP address of the switch

http://192.168.0.1, and log in with admin as both user name and

password.Then conﬁgure the switch on the GUI.

Router

LAN Port

PoE ports can also connect to non-PoE devices, but only transmit data. Maximum PoE power is 15.4W for each PoE port and 55W for all PoE ports.

3. Double click the icon on the desktop, and the utility home page displays a list of TP-LINK Easy Smart Switches on the local network.

WAN Port

Internet

Using the conguration utility

Insert the resource CD into a computer connected to the switch.

1. The resource CD home screen will appear. If not, double click AutoRun.exe on

2. the resource CD. Then click Install Easy Smart Conguration Utility on the

home screen and follow the prompts to install the program.

Make sure the switch that you want to manage is in the same subnet

4. as your computer. You can click to conﬁgure the switch IP address.

Double click the switch that you want to conﬁgure. Next enter the

5. username and password (both admin) for it. Then use the utility to conﬁgure the switch.

For more details, see the User Guide and the Easy Smart Conguration Utility User Guide on the resource CD.

LED Explanation

Link/Act(Port 1-8)

On and Green: Running at 1000Mbps On and Yellow: Running at 10/100Mbps Flashing: Transmitting/receiving data

Power

On: Power on Off: Power off

PoE Max

On: 46W≤Total power supply < 55W Flashing: Total power supply = 55W Off: Total power supply < 46W

Frequently Asked Questions (FAQ)

Q1. The Power LED is not lit

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows:

A1:

Make sure the power adapter is connected to the switch with power source properly.

A2:

Make sure the voltage of the power supply meets the requirements of the input voltage of the switch.

A3:

Make sure the power source is ON.

Q2. The Link/Act LED is not lit when a device is connected to the corresponding port

It is recommended that you check the following items:

A1:

Make sure that the cable connectors are firmly plugged into the switch and the device.

A2:

Make sure the connected device is turned on and works normally.

A3:

The cable must be less than 100 meters long (328 feet).

Q3. Why is port 4 not supplying power for PoE devices?

If connected PoE devices’ total power consumption exceeds 55W, the system will cut off the power of port 4. For example, port 1, 2 and 4 are consuming 15.4W respectively, if an additional PoE device with 12W is inserted to port 3, the system will cut off the power of port 4 to compensate for the overload.

PoE Status (Port 1-4)

On: Providing PoE power Flashing: PoE fault Off: Not providing PoE power

General

Standard

Interface

Data Transfer Rate

Network Media (Cable)

Power Supply

Backbone Bandwidth

MAC Address Table

Environmental and Physical

Certification Operating Temperature Storage Temperature Operating Humidity Storage Humidity

IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af, IEEE802.1p, IEEE802.1q

8 10/100/1000Mbps RJ45 Ports Auto-Negotiation, Auto MDI/MDIX PoE Ports: Port1- Port4, Total Power Supply: 55W Ethernet: 10Mbps(Half Duplex) 20Mbps(Full Duplex) Fast Ethernet: 100Mbps(Half Duplex) 200Mbps (Full Duplex) Gigabit Ethernet: 2000Mbps (Full Duplex) 10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 100Base-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100 1000Base-T: UTP category 5e cable or above (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) External Power Adapter Input:¬100-240VAC, 50/60Hz¬ Output: 48VDC /1.25A

16Gbps

4K, automatically learning, automatically aging

FCC, CE, RoHS 0˚C~40˚C (32˚F~104˚F)

-40˚C~70˚C (-40˚F~158˚F) 10%~90%RH non-condensing 5%~95%RH non-condensing

STP (maximum 100m)

SAFETY NOTICES

Cautions

Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced

in any form or by any means or any derivative such as translation,

used to make

http://www.tp-link.com

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.