User Guide
Easy Smart Conguration Utility
TL-SG108PE / TL-SG1016DE / TL-SG1016PE / TL-SG1024DE
1910012369 REV3.2.0
October 2018
CONTENTS
About This Guide
Intended Readers ................................................................................................................................................................1
Conventions ...........................................................................................................................................................................1
More Information .................................................................................................................................................................1
Getting Started
Introduction ............................................................................................................................................................................4
Installing the Configuration Utility .................................................................................................................................5
Discovering Switches...................................................................................................................................................... 10
Discovering the Switches in the Network .................................................................................................................................10
Configuring IP Setting for the Switch ..........................................................................................................................................11
Logging Into the Switch ......................................................................................................................................................................12
Managing System
System .................................................................................................................................................................................. 15
Overview ......................................................................................................................................................................................................15
Supported Features ..............................................................................................................................................................................15
Configuring System Info ................................................................................................................................................ 16
Viewing the System Information ....................................................................................................................................................16
Specifying the Device Description ...............................................................................................................................................17
Configuring IP ..................................................................................................................................................................... 18
Managing User Account ................................................................................................................................................. 20
Backing Up and Restoring ............................................................................................................................................. 21
Saving the Current Configuration ..................................................................................................................................................21
Restoring to the Previous Configuration ...................................................................................................................................22
Rebooting System ............................................................................................................................................................ 25
Reseting the System ....................................................................................................................................................... 26
Upgrading the Firmware ................................................................................................................................................. 27
Switching
Switching .............................................................................................................................................................................. 30
Overview ......................................................................................................................................................................................................30
Supported Features ..............................................................................................................................................................................30
Configuring Ports .............................................................................................................................................................. 32
Configuring IGMP Snooping ......................................................................................................................................... 34
Configuring LAG ................................................................................................................................................................ 35
Configuration Example ................................................................................................................................................... 36
Example for Configuring IGMP Snooping .................................................................................................................................36
Network Requirements ..........................................................................................................................................................36
Configuration Scheme ...........................................................................................................................................................36
Configuration Steps ................................................................................................................................................................37
Example for Configuring LAG ..........................................................................................................................................................38
Network Requirements ..........................................................................................................................................................38
Configuration Steps ................................................................................................................................................................39
Monitoring
Monitoring ........................................................................................................................................................................... 41
Overview ......................................................................................................................................................................................................41
Supported Features ..............................................................................................................................................................................41
Viewing Port Statistics .................................................................................................................................................... 42
Configuring Port Mirror ................................................................................................................................................... 44
Testing the Cable .............................................................................................................................................................. 46
Configuring Loop Prevention ....................................................................................................................................... 47
Configuring VLAN
Overview .............................................................................................................................................................................. 49
Configuring MTU VLAN................................................................................................................................................... 51
Configuring Port Based VLAN ...................................................................................................................................... 52
Configuring 802.1Q VLAN ............................................................................................................................................. 54
Configuring the VLAN ..........................................................................................................................................................................54
Configuring the PVID ............................................................................................................................................................................57
Configuration Example for 802.1Q VLAN ................................................................................................................ 58
Network Requirements ........................................................................................................................................................................58
Configuration Scheme ........................................................................................................................................................................58
Network Topology ..................................................................................................................................................................................59
Configuring QoS
QoS ......................................................................................................................................................................................... 63
Overview ......................................................................................................................................................................................................63
Supported Features ..............................................................................................................................................................................63
Configuring Basic QoS .................................................................................................................................................... 64
Configuring QoS in Port Based Mode .........................................................................................................................................65
Configuring QoS in 802.1P Based Mode ..................................................................................................................................66
Configuring QoS in DSCP/802.1P Based Mode ...................................................................................................................66
Configuring Bandwidth Control ................................................................................................................................... 67
Configuring Storm Control ............................................................................................................................................ 69
Configuration Example for Basic QoS....................................................................................................................... 71
Network Requirements ........................................................................................................................................................................71
Configuration Scheme ........................................................................................................................................................................71
Configuration Steps ..............................................................................................................................................................................72
Configuring PoE
Overview .............................................................................................................................................................................. 74
Configuring PoE................................................................................................................................................................. 75
Searching Help
Help ........................................................................................................................................................................................ 78
Overview ......................................................................................................................................................................................................78
Supported Features ..............................................................................................................................................................................78
Searching Online Help .................................................................................................................................................... 79
Viewing Information About the Utility........................................................................................................................ 80
About This Guide Intended Readers
About This Guide
This Configuration Guide provides information for setup and guidance of the Easy Smart
Configuration Utility. Read this guide carefully before operation.
Intended Readers
This Guide is intended for network managers familiar with IT concepts and network
terminologies.
Conventions
Some models featured in this guide may be unavailable in your country or region. For local
sales information, visit
https://www.tp-link.com
.
When using this guide, notice that features of the switch may vary slightly depending
on the model and software version you have. All screenshots, images, parameters and
descriptions documented in this guide are used for demonstration only. Throughout the
guide, we will take TL-SG1016PE as the switch to configure for example.
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied. Users must take full responsibility for their
application of any products.
In this Guide, the following conventions are used:
The symbol
make better use of your device.
Menu Name > Submenu Name > Tab page indicates the menu structure. SYSTEM >
System Info > System Summary means the System Summary page under the System Info
menu option that is located under the SYSTEM menu.
Bold font indicates a button, a toolbar icon, menu or menu item.
stands for
. Notes contain suggestions or references that help you
Note
More Information
The latest software and documentations can be found at Download Center at
https://www.tp-link.com/support
The Installation Guide (IG) can be found inside the package of the switch or at Download
Center at
Specifications can be found at Download Center at
https://www.tp-link.com/support
.
.
https://www.tp-link.com/support
User Guide 1
.
About This Guide More Information
A Technical Support Forum is provided for you to discuss our products at
https://community.tp-link.com/en/business/
Our Technical Support contact information can be found on the Contact Technical
Support page at
https://www.tp-link.com/support
.
.
User Guide 2
Part 1
Getting Started
CHAPTERS
1. Introduction
2. Installing the Conguration Utility
3. Discovering Switches
Getting Started Introduction
1
Introduction
The Easy Smart Configuration utility allows users to centrally configure the Easy Smart
Switches in the entire network. In this part, we will introduce how to install the utility
software and discover switches.
You can also configure Easy Smart Switches individually on their web management
page. For more details, refer to the User Guide of the products at Download Center at
https://www.tp-link.com/support
.
User Guide 4
Getting Started Installing the Configuration Utility
2
Installing the Configuration Utility
Follow these steps to install the Easy Smart Configuration Utility:
1) Download the software installation packet of Easy Smart Configuration Utility onto your
computer. You can find the packet on the product page of the switch at
https://www.tp-link.com
2) Decompress the packet and double click Easy Smart Configuration Utility v1.1.1.0.exe
to launch the InstallShield Wizard. The following page will be displayed.
Figure 2-1 Preparing Setup
.
User Guide
5
Getting Started Installing the Configuration Utility
3) Wait a moment until the following page is displayed.
Figure 2-2 Launching the Installshield Wizard
4) Click Next to load the following page. Choose the destination location for the
installation files. By default, the installation files are saved in the Program Files folder of
User Guide 6
Getting Started Installing the Configuration Utility
the system disk. You can lick Change to modify the destination location according to
your needs.
Figure 2-3 Choosing the Deitination Location
5) Click Next to load the following page. The wizard is ready to begin the installation.
Figure 2-4 Getting Ready to Install the Software
User Guide
7
Getting Started Installing the Configuration Utility
6) Click Install to load the following page. The wizard will install Easy Smart Configuration
Utility.
Figure 2-5 Installing the Utility
7) Wait a moment until the following page is displayed when the installation is completed.
Click Finish to exit the wizard. By default, the installation process creates a TP-Link
subdirectory under the \Program Files directory on your computer, copies the utility
User Guide 8
Getting Started Installing the Configuration Utility
program into the \Program Files\TP-Link\Easy Smart Configuration Utility directory,
and places a utility icon
Figure 2-6 Finishing Installation
on the computer desktop.
User Guide
9
Getting Started Discovering Switches
3
Discovering Switches
With the Switch Discovery fuction of the utility, you can:
Discover the switches in the network.
Configure IP setting for the switch.
Log into the switch.
3.1 Discovering the Switches in the Network
Double click to launch the Easy Smart Configuration Utility, it searches the network for
TP-Link Easy Smart switches automatically. The discovered switches are listed as below.
Figure 3-1 Discovering Switches
Note:
The maximum number of the discovered switches is 30.
•
You can click Help in the left bottom to access the TP-Link support website for more help
•
about the switches, if you have access to the internet.
Each time the network environment changes, it is recommended to click Refresh to restart
•
the switch discovery process.
User Guide 10
Getting Started Discovering Switches
3.2 Configuring IP Setting for the Switch
Select the switch that you want to configure, and click to load the following page.
Figure 3-2 Configuring IP Address
Follow these steps to configure IP setting for the switch.
1) Verify the information of the switch. You can view the MAC address, hardware version,
and firmware version of the switch.
2) Enter a proper device description for the switch according to your needs to distinguish
different devices in your network.
3) Configure IP address, subnet mask, and default gateway for the switch. You can either
configure the parameters manually or use DHCP.
Configuring the parameters manually
Select DHCP setting as Disable. Specify the IP address, subnet mask and default
gateway for the switch.
IP Address Enter the IP address of the switch. You can use this IP address to access
the switch. The default IP address of the switch is 192.168.0.1.
User Guide
11
Getting Started Discovering Switches
Subnet Mask Enter the subnet mask of the switch. The default subnet mask of the
switch is 255.255.255.0.
Default Gateway Enter the default gateway of the switch.
Using DHCP
Select DHCP setting as Enable.
4) Input the user name and password. The user name and password are both admin by
default.
5) Click Apply.
Note:
If you enable DHCP setting, the switch will try to obtain IP address, subnet mask, and
default gateway from the DHCP server in the network. If the switch cannot get IP settings
from the DHCP server, it will use the default IP address of 192.168.0.1 and subnet mask of
255.255.255.0.
3.3 Logging Into the Switch
Select the switch which you want to log into, and click to load the following page.
Figure 3-3 Logging Into the Switch
Follow these steps to log into the switch.
1) Input the user name and password. The user name and password are both admin by
default.
2) (Optional) Check Remember Me to remember the user name and password.
User Guide 12
Getting Started Discovering Switches
3) Click Login. The following page will be displayed and you can configure the switch on
this page. The model and hardware version of the switch that you are configuring are
shown in the top-right corner.
Figure 3-4 Launching the Configuration Interface
Note:
You can click to return to the switch discovery page.
•
When you make changes and click Apply, the switch will save the configurations
•
immediately.
If you configure the switch after a long duration without operation (more than 600s), the
•
utility will return to the Home page and refresh.
User Guide
13
Part 2
Managing System
CHAPTERS
1. System
2. Configuring System Info
3. Configuring IP
4. Managing User Account
5. Backing Up and Restoring
6. Rebooting System
7. Reseting the System
8. Upgrading the Firmware
Managing System System
1
System
1.1 Overview
With the Managing System function, you can view the system information and configure
the system parameters and features of the switch.
1.2 Supported Features
System Info
The System Info is mainly used to view the system information and configure the device
description.
IP Setting
Each device in the network possesses a unique IP address. You can access the switch
using this IP address. You can set IP address of the switch manually or using DHCP.
User Account Management
User Account Management is mainly used to modify the username and password in order
to refuse illegal users.
Backup and Restore
Backup and Restore is used to save the current configuration file in your computer, and
upload a configuration file to restore your switch to the previous configuration.
System Reboot
System Reboot is used to reboot the switch.
System Reset
System Reset is used to reset the switch to the default setting.
Firmware Upgrade
To upgrade the firmware is to get more functions and better performance. Go to the
website
https://www.tp-link.com
to download the updated firmware.
User Guide
15
Managing System Configuring System Info
2
Configuring System Info
With the System Info function, you can:
View the system information
Specify the device description
2.1 Viewing the System Information
Choose the menu System > System Info to load the following page. You can view the basic
system information of the switch.
Figure 2-1 Viewing the System Summary
User Guide 16
Managing System Configuring System Info
2.2 Specifying the Device Description
Choose the menu System > System Info to load the following page. Specify a new device
description for the switch, and click Apply.
Figure 2-2 Specifying the Device Description
User Guide
17
Managing System Configuring IP
3
Configuring IP
You can configure the system IP address in the following two ways:
Configure the System IP Address Using DHCP
Configure the System IP Address Manually
Configuring the System IP Address Using DHCP
Choose the menu System > IP Setting to load the following page.
Figure 3-1 Configuring System IP Address with DHCP Enabled
Follow these steps to configure the system IP address using DHCP:
1) Select DHCP setting as Enable from the drop-down list.
2) Click Apply. Then the switch will try to obtain IP address, subnet mask, and default
gateway from the DHCP server in the network. If the switch cannot get IP settings from
the DHCP server, it will use the default IP address of 192.168.0.1 and subnet mask of
255.255.255.0.
Configuring the System IP Address Manually
Choose the menu System > IP Setting to load the following page.
Figure 3-2 Configuring System IP Address Manually
User Guide 18
Managing System Configuring IP
Follow these steps to configure the system IP address manually:
1) Select DHCP setting as Disable from the drop-down list.
2) Specify the IP address, subnet mask and default gateway.
IP Address Enter the IP address of the switch. You can use this IP address to access
the switch. The default IP address of the switch is 192.168.0.1
Subnet Mask Enter the subnet mask of the switch. The default subnet mask of the switch
is 255.255.255.0.
Default Gateway Enter the default gateway of the switch.
3) Click Apply.
User Guide
19
Managing System Managing User Account
4
Managing User Account
With user account management, you can modify the username and password to refuse
illegal users.
Choose the menu System > User Account to load the following page.
Figure 4-1 Managing the User Account
Follow these steps to configure the user account:
1) Specify the user name, enter the old password, specify a new password and confirm
the new password.
User Name Create a user name for login. The user name should not be more than 16
characters using digits, letters and underlines only.
Old Password Enter the old password of the switch. By default, the old password is
admin.
New Password Specify a new password for login.
Confirm
Password
2) Click Apply.
Retype the new password.
User Guide 20
Managing System Backing Up and Restoring
5
Backing Up and Restoring
With the Backup and Restore function, you can:
Save the current configuration.
Restore to the previous configuration.
5.1 Saving the Current Configuration
Choose the menu System > Backup and Restore to load the following page.
Figure 5-1 Backing Up System Config
User Guide
21
Managing System Backing Up and Restoring
Follow these steps to save the current configuration:
1) In the System Config Backup section, Click Backup Config to load the following page.
Specify the file path and file name for the configuration file to save.
Figure 5-2 Saving the Configuration File
2) Click Save.
Note:
It will take a moment to save the configuration. Wait without any operation when saving the
configuration file.
5.2 Restoring to the Previous Configuration
Choose the menu System > Backup and Restore to load the following page.
Figure 5-1 Restoring System Config
User Guide 22
Managing System Backing Up and Restoring
Follow these steps to restore the switch to the previous configuration:
1) In the System Config Restore section, Click Choose File to load the following page.
Specify the configuration file path and select the configuration file. Click Open.
Figure 5-2 Choosing the Configuration File
2) The following page will be dispayed.
Figure 5-3 Choosing the Configuration File
User Guide
23
Managing System Backing Up and Restoring
3) Click Restore Config, and the following page will be displayed. Click Yes to restore the
switch to the previous configuration. It will take effect after the switch automatically
reboots.
Figure 5-4 Being sure to restore config
Note:
It will take a moment to restore the configuration. Wait without any operation.
•
To avoid any damage, do not power down the switch while the switch is being restored.
•
After being restored, the current configuration of the switch will be lost.
•
User Guide 24
Managing System Rebooting System
6
Rebooting System
Choose the menu System > System Reboot to load the following page. Click Reboot.
Figure 6-1 Rebooting the System
Note:
It will take a moment to reboot the system. Wait without any operation.
•
To avoid any damage, do not power down the switch while the system reboots.
•
User Guide
25
Managing System Reseting the System
7
Reseting the System
Choose the menu System > System Reset to load the following page.
Figure 7-1 Reseting the System
Follow these steps to reset the switch.
1) Click Reset, and the following page will be displayed.
Figure 7-2 Being Sure to Reset the System
2) Click Yes to reset the system.
Note:
It will take a moment to reset the system. Wait without any operation.
•
To avoid any damage, do not power down the switch during the reset.
•
After the system is reset, it will reboot automatically.
•
After the system is reset, all the settings will be restored to the default.
•
User Guide 26
Managing System Upgrading the Firmware
8
Upgrading the Firmware
Choose the menu System > Firmware Upgrade to load the following page.
Figure 8-1 Upgrading the Firmware
Follow these steps to upgrade the firmware:
1) Click Choose File to load the following page. Enter the file path of the firmware in the
address bar and select the firmware. Click Open.
Figure 8-2 Choosing the Firmware
2) The following page will be displayed.
Figure 8-3 Choosing the Firmware
User Guide
27
Managing System Upgrading the Firmware
3) Click Upgrade Firmware to load the following page. Click Yes to upgrade the firmware.
Figure 8-4 Being Sure to Upgrade the Firmware
Note:
It is recommended to backup the configuration before upgrading.
•
If your PC and switch are not in the same subnet, you cannot upgrade firmware. Before you
•
upgrade firmware, configure the IP address of your PC to ensure your PC and switch are in
the same subnet.
It will take a moment to upgrade the firmware. Wait without any operation.
•
Select the proper software version matching with your hardware to upgrade.
•
To avoid damage, do not power down the switch while upgrading the firmware.
•
After upgrading, the switch will reboot automatically.
•
User Guide 28
Part 3
Switching
CHAPTERS
1. Switching
2. Configuring Ports
3. Configuring IGMP Snooping
4. Configuring LAG
5. Configuration Example
Switching Switching
1
Switching
1.1 Overview
With the Switching function, you can configure port setting, IGMP Snooping and LAG.
1.2 Supported Features
The switch supports the following features about switching:
Port Setting
You can configure port status, speed, duplex mode, and flow control for ports.
IGMP Snooping
In a point-to-multipoint network, packets can be sent in three ways: unicast, broadcast
and multicast. With unicast, many copies of the same information will be sent to all the
receivers, occupying a large bandwidth.
With broadcast, information will be sent to all users in the network no matter they need it or
not, wasting network resources and impacting information security.
Multicast, however, solves all the problems caused by unicast and broadcast. With
multicast, the source only needs to send one piece of information, and all and only the users
who need the information will receive copies of the information. In a point-to-multipoint
network, multicast technology not only transmits data with high efficiency, but also saves a
large bandwidth and reduces network load.
When IGMP Snooping is disabled on the switch, multicast packets will be broadcast in
the Layer 2 network; when IGMP Snooping is enabled on the switch, multicast data from
User Guide 30
Switching Switching
a known multicast group will be transmitted to the designated receivers instead of being
broadcast in the Layer2 network. The following figure shows how IGMP snooping works.
Figure 1-1 IGMP Snooping
LAG
Multicast packets transmission
without IGMP Snooping
Multicast router
Source
Layer 2 switch
Host A Host B Host C
Receiver Receiver
Multicast packets
Multicast packets transmission with
IGMP Snooping
Multicast router
Source
Layer 2 switch
Host A Host B Host C
Receiver Receiver
With LAG (Link Aggregation Group) function, you can aggregate multiple physical ports into
a logical interface to increase link bandwidth and enhance the connection reliability.
User Guide
31
Switching Configuring Ports
2
Configuring Ports
Choose the menu Switching > Port Setting to load the following page.
Figure 2-1 Configuring Ports
Follow these steps to configure the port parameters.
1) Select the desired ports and set basic parameters for the ports.
Status Enable or disable the port. With this option enabled, the port forwards packets
normally. Otherwise, the port does not forward packets. By default, it is enabled.
Speed/Duplex Config: Select the appropriate speed and duplex mode for the port. When Auto
is selected, the port automatically negotiates speed mode with the connected
device. The default setting is Auto. It is recommended to select Auto if both ends
of the link support auto-negotiation.
Actual: Displays the actual working state of the port.
Flow Control Config: Select On or Off to enable or disable the Flow Control feature. When Flow
Control is enabled, when the switch get overloaded, it will send a PAUSE frame
to notify the peer device to stop sending data for a specific period of time, thus
avoiding the packet loss caused by congestion. By default, it is Off.
Actual: Displays the current state of the Flow Control function of the port.
User Guide 32
Switching Configuring Ports
LAG Displays the LAG which the port belongs to.
2) Click Apply.
Note:
It is recommended to set the ports on both ends of a link with the same speed and duplex
•
mode.
Keep the port that is connected to the management device enabled, or you cannot access the
•
switch.
The parameters of the port members in a LAG should be set as the same.
•
User Guide
33
Switching Configuring IGMP Snooping
3
Configuring IGMP Snooping
Choose the menu Switching > IGMP Snooping to load the following page.
Figure 3-1 Configuring IGMP Snooping
Follow these steps to configure IGMP Snooping.
1) In the IGMP Snooping section, enable IGMP Snooping. Enable or disable Report
Message Suppression according to your needs. Click Apply.
IGMP Snooping Enable or disable IGMP Snooping globally.
Report Message
Suppression
2) In the Multicast IP Table section, you can view the current IGMP group information.
IP Address Displays the IP address of the multicast group.
VLAN ID Displays the VLAN ID of the multicast group. All port members of a multicast
Ports Displays the forwarding port list of the multicast group.
Enable or disable Report Message Suppression globally. When enabled, the
switch will only forward the first IGMP report message for each multicast group to
the IGMP querier and suppress subsequent IGMP report messages for the same
multicast group during one query interval. This feature prevents duplicate report
messages from being sent to the IGMP querier.
group should be included in the same VLAN.
User Guide 34
Switching Configuring LAG
4
Configuring LAG
Choose the menu Switching > LAG to load the following page.
Figure 4-1 Configuring LAG
Follow these steps to configure LAG:
1) In the LAG Config section, select an LAG ID and click the ports to add to the LAG. Click
Apply.
2) In the LAG Table section, you can verify the LAG configuration result. You can select
the LAG and click Delete to delete ports from the LAG group.
LAG ID Displays the ID of the LAG group.
Ports Displays the LAG member ports.
Note:
Ensure that devices on both ends of the aggregation link use the same number of physical
•
ports with the same speed and duplex mode, flow control setting and QoS setting.
The LAG member ports cannot be set as the mirroring port or mirrored port.
•
It is recommended to configure the LAG function before configuring the other functions for
•
the member ports.
User Guide
35
Switching Configuration Example
5
Configuration Example
5.1 Example for Configuring IGMP Snooping
5.1.1 Network Requirements
Host B, Host C and Host D are in the same VLAN of the switch. All of them want to receive
multicast streams sent to the same multicast group.
As shown in the following topology, Host B, Host C and Host D are connected to port1,
port2 and port 3 respectively. Port 4 is the router port connected to the multicast querier.
Figure 5-1 Network Topology for Basic IGMP Snooping
Internet
Source
Host B
Receiver
5.1.2 Configuration Scheme
Add the three member ports and the router port to a VLAN.
Port 1
Port 4
Port 2
Host C
Receiver
VLAN 2
Querier
Port 3
Host D
Receiver
Enable IGMP Snooping.
Demonstrated with TL-SG105E, the following section provides configuration steps.
User Guide 36
Switching Configuration Example
5.1.3 Configuration Steps
1) Choose the menu VLAN > 802.1Q VLAN to load the following page. Select the 802.1Q
VLAN status as Enable. Click Apply. Specify the VLAN ID as 2. Specify the VLAN name
as VLAN2. Select port 1, port 2 and port 3 as untagged ports. Select port 4 as a tagged
port. Click Apply.
Figure 5-2 Configuring 802.1Q VLAN
2) Choose the menu VLAN > 802.1Q VLAN PVID Setting to load the following page.
Select port 1, port 2, port 3 and port 4, and specify the PVID as 2 for the ports. Click
Apply.
Figure 5-3 Configuring 802.1Q PVID
User Guide
37
Switching Configuration Example
3) Choose the menu Switching > IGMP Snooping to load the following page. Enable IGMP
Snooping, and click Apply.
Figure 5-4 Configuring IGMP Snooping
5.2 Example for Configuring LAG
5.2.1 Network Requirements
As shown below, hosts and servers are connected to Switch A and Switch B, and heavy
traffic is transmitted between the two switches. To achieve high speed and reliability of
data transmission, you can bundle multiple physical ports into one logical interface. In this
case, we bundle port 1, port 2 and port 3 of both switches into one logical interface.
Figure 5-1 Network Topology
Port 1
Port 3
Servers
Hosts
Port 1
Port 2 Port 2
Switch A Switch B
Port 3
Demonstrated with TL-SG105E, the following section provides configuration steps. The
configuration steps are similar for both switches, here we take Switch A for example.
User Guide 38
Switching Configuration Example
5.2.2 Configuration Steps
Choose the menu Switching > LAG to load the following page. In the LAG Config section,
select Port 1, Port 2 and Port 3 to add to the LAG 1. Click Apply.
Figure 5-1 Configuring LAG
User Guide
39
Part 4
Monitoring
CHAPTERS
1. Monitoring
2. Viewing Port Statistics
3. Configuring Port Mirror
4. Testing the Cable
5. Configuring Loop Prevention
Monitoring Monitoring
1
Monitoring
1.1 Overview
With the monitoring feature, you can monitor the traffic on the switch.
1.2 Supported Features
Port Statistics
Port Statistics is used to display the information of each port, which facilitates you to
monitor the traffic and locate faults promptly.
Port Mirror
Port Mirror is used to monitor network traffic by forwarding copies of incoming and
outgoing packets from one or multiple ports (mirrored ports) to a specified port (mirroring
port). Generally, the mirroring port is connected to a data diagnosis device, which is used
to analyze the mirrored packets for monitoring and troubleshooting the network.
Cable Test
The switch provides cable test to diagnose the connection status of the cable connected
to the switch and the distance to the problem location, which facilitates you to locate and
diagnose the trouble spot of the network.
Loop Prevention
With loop prevention feature enabled, the switch can detect loops using loop detection
packets. When a loop is detected, the switch will block the corresponding port
automatically.
User Guide
41
Monitoring Viewing Port Statistics
2
Viewing Port Statistics
Choose the menu Monitoring > Port Statistics to load the following page.
Figure 2-1 Viewing Port Statistics
You can view the statistics of each port. You can click Clear to clear the data, also you can
click Refresh to refresh the data.
Port Displays the port number of the switch.
Status Display whether the port is enabled or disabled.
Link Status Displays the link state of the port.
TxGoodPkt Displays the number of packets transmitted on the port. Error packets are not
counted in.
TxBadPkt Displays the number of error packets transmitted on the port.
RxGoodPkt Displays the number of packets received on the port. Error packets are not
counted in.
RxbadPkt Displays the number of error packets received on the port.
User Guide 42
Monitoring Viewing Port Statistics
Note:
The frames with more than 1518 bytes, less than 64 bytes or with bad Frame Check Sequence
•
(FCS) are recorded as BadPkts.
Because of the supporting feature of jumbo frame, the frames with more than 1518 bytes and
•
less than 10000 bytes will be recorded as GoodPkts and BadPkts at the same time, and can be
forwarded normally.
User Guide
43
Monitoring Configuring Port Mirror
3
Configuring Port Mirror
For TL-SG108PE
Choose the menu Monitoring > Port Mirror to load the following page.
Figure 3-1 Configuring Port Mirror
Follow these steps to configure port mirror:
1) In the Port Mirror section, Select the port mirror status as Enable. Specify the mirroring
port. In the Mirrored Port section, select a mirrored mode according to your needs, and
select one or more mirrored ports.
Port Mirror
Status
Mirroring Port/
Mirrored Ports
Mirrored Mode Select the mirrored mode according to your needs.
2) Click Apply.
Enable or disable the port mirror feature globally.
Traffic passing through the mirrored ports is mirrored to the mirroring port.
Ingress: With this option enabled, only the packets received by the
mirrored ports are copied to the mirroring port.
Egress: With this option enabled, only the packets sent by the mirrored
ports are copied to the mirroring port.
Both: With this option enabled, the packets both sent and received by the
mirrored ports are copied to the mirroring port.
User Guide 44
Monitoring Configuring Port Mirror
For TL-SG1016DE/ TL-SG1024DE/ TL-SG1016PE
Choose the menu Monitoring > Port Mirror to load the following page.
Figure 3-2 Configuring Port Mirror
Follow these steps to configure port mirror:
1) In the Port Mirror section, specify the port mirror status as Enable. Specify the
mirroring port. In the Mirrored Port section, configure whether the ingress and egress
packets of each port are mirrored or not.
Port Mirror
Status
Mirroring Port/
Mirrored Ports
Ingress For each port, with this option enabled, the packets received by the port
Egress For each port, with this option enabled, the packets sent by the port are
Enable or disable the port mirror feature globally.
Traffic passing through the mirrored ports is mirrored to the mirroring port.
are copied to the mirroring port. With this option disabled, the packets
received by the port are not copied to the mirroring port.
copied to the mirroring port. With this option disabled, the packets sent by
the port are not copied to the mirroring port.
2) Click Apply.
User Guide
45
Monitoring Testing the Cable
4
Testing the Cable
Choose the menu Monitoring > Cable Test to load the following page.
Figure 4-1 Testing the Cable
Follow these steps to test the cable:
1) Select your desired port for test, and click Test. You can also click Test All to test all
the cables.
2) Check the test results in the table.
Port Displays the port number.
Test Result Displays the cable status. Test results include normal, close (or short),
open and crosstalk.
Normal : The cable is connected normally.
Close (or short): A short circuit is being caused by abnormal contact of
wires in the cable.
Open: No device is connected to the other end or the connection is
broken.
Crosstalk: Impedance mismatch due to the poor quality of the cable.
Cable Fault
Distance (m)
If the connection status is short, close (or short) or crosstalk, here displays
the length from the port to the trouble spot.
User Guide 46
Monitoring Configuring Loop Prevention
5
Configuring Loop Prevention
Choose the menu Monitoring > Loop Prevention to load the following page.
Figure 5-1 Configuring Loop Prevention
Follow these steps to configure loop prevention:
1) Select the loop prevention status as Enable or Disable from the drop-down list.
Loop Prevention
Status
2) Click Apply.
Enable or disable the loop prevention feature globally.
User Guide
47
Part 5
Configuring VLAN
CHAPTERS
1. Overview
2. Configuring MTU VLAN
3. Configuring Port Based VLAN
4. Configuring 802.1Q VLAN
5. Configuration Example for 802.1Q VLAN
Configuring VLAN Overview
1
Overview
VLAN (Virtual Local Area Network) is a network technique that solves broadcasting issues
in local area networks. It is usually applied in the following occasions:
To restrict broadcast domain: VLAN technique divides a big local area network into
several VLANs, and all VLAN traffic remains within its VLAN. It reduces the influence of
broadcast traffic in Layer 2 network to the whole network.
To enhance network security: Devices from different VLANs cannot achieve Layer 2
communication, and thus users can group and isolate devices to enhance network
security.
For easier management: VLANs group devices logically instead of physically, so devices
in the same VLAN need not be located in the same place. It eases the management of
devices in the same work group but located in different places.
There are 3 types of VLAN modes supported on the switch:
MTU VLAN
MTU VLAN (Multi-Tenant Unit VLAN) defines an uplink port which will build up several
VLANs with each of the other ports. Each VLAN contains two ports, the uplink port and
one of the other ports in the switch, so the device connected to the uplink port can
communicate with the device connected to any other port, but devices connected to other
ports cannot communicate with each other.
Port Based VLAN
VLANs are divided based on ports. In port based VLAN mode, each port can only be added
to one VLAN.
802.1Q VLAN
The IEEE 802.1Q protocol defines a new format of VLAN data frame (Tagged Frame). As the
following figure shows, compared to the traditional Ethernet data frame (Untagged Frame),
the VLAN data frame (Tagged Frame) adds a VLAN tag.
On receiving a tagged frame, the switch checks the VID (VLAN ID) contained in the VLAN
tag to determine which VLAN the frame belongs to. On receiving an untagged frame, the
switch will first insert a VLAN tag to the frame, using the PVID (Port VLAN ID) of the port as
its VID, and then forward it as a tagged frame.
User Guide
49
Configuring VLAN Overview
Note:
The switch works in one and only one VLAN mode at any time. When a specific VLAN mode is
enabled, the other two VLAN modes will be disabled automatically and the corresponding VLAN
configuration will be lost.
User Guide 50
Configuring VLAN Configuring MTU VLAN
2
Configuring MTU VLAN
Choose the menu VLAN > MTU VLAN to load the following page.
Figure 2-1 Configuring MTU VLAN
Follow these steps to configure MTU VLAN:
1) Select the MTU VLAN status as Enable from the drop-down list. Select the desired
uplink port from the drop-down list. Click Apply.
MTU VLAN
Status
Enable or disable the MTU VLAN mode.
Uplink Port Select the desired uplink port from the drop-down list. The uplink port
builds up several VLANs with each of the other ports.
2) The following page will be displayed. Click Yes.
Figure 2-2 Being Sure to Enable MTU VLAN
User Guide
51
Configuring VLAN Configuring Port Based VLAN
3
Configuring Port Based VLAN
Choose the menu VLAN > Port Based VLAN to load the following page.
Figure 3-1 Configuring Port Based VLAN
Follow these steps to configure port based VLAN:
1) In the Global Config section, select the port based VLAN status as Enable from the
drop-down list. Click Apply.
Port Based
VLAN Status
2) The following page will be displayed. Click Yes.
Figure 3-2 Being Sure to Enable Port Based VLAN
3) In the Port Based VLAN Setting section, Select the ID for the VLAN and ports to add to
the VLAN. Click Apply.
Enable or disable the port based VLAN mode.
VLAN Select the ID for the VLAN which you want to add ports to.
Ports Select the ports to add to the VLAN.
User Guide 52
Configuring VLAN Configuring Port Based VLAN
4) You can verify the configuration result of port based VLAN in the table. You can delete a
VLAN as you wish by selecting the VLAN and clicking Delete.
Figure 3-3 Verifying the Configuration Result
Note:
By default, all the ports are added to VLAN 1.
•
Once a port is added to another VLAN, it is deleted from the original VLAN automatically.
•
Once a port is removed from all the other VLANs, it is added to VLAN 1 automatically.
•
VLAN 1 includes at least one port and cannot be deleted.
•
User Guide
53
Configuring VLAN Configuring 802.1Q VLAN
4
Configuring 802.1Q VLAN
To complete the 802.1Q VLAN configuration, follow these steps:
1) Configure the VLAN, including creating a VLAN and adding the ports to the VLAN.
2) Configure the PVID.
4.1 Configuring the VLAN
Choose the menu VLAN > 802.1Q VLAN to load the following page.
Figure 4-1 Configuring 802.1Q VLAN
Follow these steps to configure the VLAN:
1) In the Global Config section, Select the 802.1Q VLAN status as Enable from the
drop-down list. Click Apply.
802.1Q VLAN
Status
Enable or disable the 802.1Q VLAN mode.
User Guide 54
Configuring VLAN Configuring 802.1Q VLAN
2) The following page will be displayed. Click Yes.
Figure 4-2 Being Sure to Enable 802.1Q VLAN
3) In the 802.1Q VLAN Setting section, enter a VLAN ID and a VLAN name for identification
to create a VLAN. Select the untagged port(s) and the tagged port(s) respectively to
add to the created VLAN based on the network topology. Click Apply.
VLAN (1-4094) Enter a VLAN ID, which rages from 1 to 4094, for identification.
VLAN Name Enter a VLAN name for identification. The VLAN name should not be more
than 10 characters using digits, letters, hyphens, and underlines only.
Tagged Ports /
Untagged Ports
Select the ports to add to the VLAN as tagged ports or untagged ports.
The unselected ports do not forward frames in the target VLAN.
Tagged Ports: Tagged ports forward frames in the target VLAN with the
current VLAN tags remained.
Untagged Ports: Untagged ports forward frames in the target VLAN after
removing the VLAN tags.
User Guide
55
Configuring VLAN Configuring 802.1Q VLAN
4) You can verify the configuration result of 802.1Q VLAN in the table. You can delete a
VLAN as you wish by selecting the VLAN and clicking Delete.
Figure 4-3 Verifying the Configuration Result
Note:
By default, all the ports are added to VLAN 1.
•
The port can be removed from VLAN 1 only when the port is also a member of the other
•
VLANs.
Once a port is removed from the current VLANs, it is added to VLAN 1 automatically.
•
VLAN 1 cannot be deleted.
•
User Guide 56
Configuring VLAN Configuring 802.1Q VLAN
4.2 Configuring the PVID
Choose the menu VLAN > 802.1Q VLAN PVID Setting to load the following page.
Figure 4-4 Configuring 802.1Q PVID
Follow these steps to configure the PVID:
1) Select the ports and set the PVID for the ports.
PVID Set the PVID for the ports. The PVID ranges from 1 to 4094.
2) Click Apply.
Note:
The PVID configuration will takes effect only when 802.1Q VLAN mode is enabled.
•
You can specify a PVID only when the corresponding VLAN exists.
•
User Guide
57
Configuring VLAN Configuration Example for 802.1Q VLAN
5
Configuration Example for 802.1Q VLAN
5.1 Network Requirements
Offices of Department A and Department B in the company are located in different
places, and some computers in different offices are connected to the same switch.
It is required that computers can communicate with each other in the same department
but not with computers in the other department.
5.2 Configuration Scheme
Divide computers in Department A and Department B into two VLANs respectively so
that computers can communicate with each other in the same department but not with
computers in the other department.
Terminal devices like computers usually do not support VLAN tags. Add untagged ports
to the corresponding VLANs and specify the PVID.
The intermediate link between two switches carries traffic from two VLANs
simultaneously. Add the tagged ports to both VLANs.
User Guide 58
Configuring VLAN Configuration Example for 802.1Q VLAN
5.3 Network Topology
The figure below shows the network topology. Host A1 and Host A2 are in Department
A, while Host B1 and Host B2 are in Department B. Switch A and Switch B are located in
two different places. Host A1 and Host B1 are connected to port 2 and port 3 on SwitchA
respectively, while Host A2 and Host B2 are connected to port 2 and port 3 on Switch B
respectively. Port 4 on Switch A is connected to port 4 on Switch B.
Figure 5-1 Network Topology
VLAN 2
Host A1 Host A2
Switch A
Port 2
Port 4
Port 4
Port 3
VLAN 3
Host B1
Port 2
Switch B
Port 3
Host B2
Demonstrated with TL-SG105E, the following section provides configuration steps. The
configuration steps on both switches are similar, here we take Switch A for example.
1) Choose the menu VLAN > 802.1Q VLAN to load the following page. In the Global
Config section, Select the 802.1Q VLAN status as Enable from the drop-down list. Click
Apply.
Figure 5-2 Configuring 802.1Q VLAN
User Guide
59
Configuring VLAN Configuration Example for 802.1Q VLAN
2) The following page will be displayed. Click Yes.
Figure 5-3 Enableing 802.1Q VLAN
3) The following page will be displayed. In the 802.1Q VLAN Setting section, specify the
VLAN ID as 2, specify the VLAN name as Dept_A. Add port 4 to the VLAN as a tagged
port. Add port 2 to the VLAN as an untagged port. Click Apply.
Figure 5-4 Creating VLAN 2 and Adding Ports to the VLAN
4) Choose the menu VLAN > 802.1Q VLAN to load the following page. In the 802.1Q VLAN
Setting section, specify the VLAN ID as 3, specify the VLAN name as Dept_B. Add
User Guide 60
Configuring VLAN Configuration Example for 802.1Q VLAN
port 4 to the VLAN as a tagged port. Add port 3 to the VLAN as an untagged port. Click
Apply.
Figure 5-5 Creating VLAN 3 and Adding Ports to the VLAN
5) Choose the menu VLAN > 802.1Q VLAN PVID Setting to load the following page. Set
the PVID of port 2 as 2 and click Apply. Set the PVID of port 3 as 3 and click Apply.
Figure 5-6 Configuring 802.1Q PVID
User Guide
61
Part 6
Configuring QoS
CHAPTERS
1. QoS
2. Configuring Basic QoS
3. Configuring Bandwidth Control
4. Configuring Storm Control
5. Configuration Example for Basic QoS
Configuring QoS QoS
1
QoS
1.1 Overview
With network scale expanding and applications developing, internet traffic is dramatically
increased, thus resulting in network congestion, packet drops and long transmission delay.
Typically, networks treat all traffic equally on FIFO (First In First Out) delivery basis, but
nowadays many special applications like VoD, video conferences, VoIP, etc. require more
bandwidth or shorter transmission delay to guarantee the performance.
With QoS (Quality of Service) technology, you can classify and prioritize network traffic to
provide differentiated services to certain types of traffic.
1.2 Supported Features
With the QoS feature, You can configure QoS Basic, Bandwidth Control and Storm Control
on the switch to maximize the network performance and bandwidth utilization.
QoS Basic
The switch classifies the ingress packets, maps the packets to different priority queues
and then forwards the packets to implement QoS function.
Bandwidth Control
Bandwidth Control functions to control the ingress traffic rate and egress traffic rate on
each port via configuring the available bandwidth of each port. In this way, the network
bandwidth can be reasonably distributed and utilized.
Storm Control
Storm Control function allows the switch to monitor broadcast packets, multicast packets
and UL-frames (Unknown unicast frames) in the network. If the transmission rate of the
packets exceeds the limit, the packets will be automatically discarded to avoid network
broadcast storm.
User Guide
63
Configuring QoS Configuring Basic QoS
2
Configuring Basic QoS
Configuration Guidelines
Select the QoS mode according to your network requirements. Three QoS modes are
supported on the switch: Port Based, 802.1P Based and DSCP Based (DSCP/802.1P
Based).
Port Based
The port based QoS mode supports four priority queues, which are labeled as 1 (Lowest),
2(Normal), 3 (Medium) and 4 (Highest).
In this mode, the switch prioritizes packets according to their ingress ports, regardless of
the packet field or type.
802.1P Based
802.1P defines the first three bits in 802.1Q Tag as PRI field. The PRI values are from 0 to7.
The tagged packets are mapped to 4 priority levels based on the PRI value (Lowest=1, 2;
Normal=0, 3; Medium=4, 5; Highest=6, 7).
In this mode, the switch only prioritizes packets with VLAN tag, regardless of the IP header
of the packets.
DSCP/802.1P Based
DSCP priority determines the priority of packets based on the ToS (Type of Service) field
in their IP header. RFC 2474 re-defines the ToS field in the IP packet header as DS field.
The first six bits of the DS field is used to represent DSCP priority. The DSCP values are
from 0 to 63. The IP packets are mapped to 4 priority levels based on the DSCP value
(Lowest=0-15; Normal=16-31; Medium=32-47; Highest=48-63).
In this mode, the switch prioritizes packets with IP header based on DSCP priority first.
Then, the switch prioritizes packets with VLAN tag but without IP header based on the PRI
field. Finally, the switch prioritizes packets without VLAN tag or IP header based on port
priority.
User Guide 64
Configuring QoS Configuring Basic QoS
2.1 Configuring QoS in Port Based Mode
Choose the menu QoS > QoS Basic to load the following page.
Figure 2-1 Configuring Basic QoS in Port Based Mode
Follow these steps to configure QoS in port based mode:
1) In the Global Config section, select QoS mode as Port Based. Click Apply.
QoS Mode Select the QoS mode.
Port Based: In port based mode, the switch prioritizes packets according
to their ingress ports, regardless of the packet field or type.
2) In the Port Based Priority Setting section, select the desired ports and specify the
priority queue for the ports. Click Apply.
Priority Queue Specify the priority queue that the packets from the port are mapped to.
The priorities are labeled as 1, 2, 3, and 4. Among them, the bigger value
means the higher priority.
LAG Displays the LAG which the port belongs to.
User Guide
65
Configuring QoS Configuring Basic QoS
2.2 Configuring QoS in 802.1P Based Mode
Choose the menu QoS > QoS Basic to load the following page.
Figure 2-2 Configuring Basic QoS in 802.1P Based Mode
Follow these steps to configure QoS in 802.1P based mode:
1) Select QoS mode as 802.1P Based.
QoS Mode Select the QoS mode .
802.1P Based: In 802.1P based mode, the tagged packets are mapped to
4 priority levels based on the Pri value in 802.1Q tag (Lowest = 1, 2; Normal
=0, 3; Medium= 4, 5; Highest = 6, 7). The switch only prioritizes packets with
VLAN tag, regardless of the IP header of the packets.
2) Click Apply.
2.3 Configuring QoS in DSCP/802.1P Based Mode
Choose the menu QoS > QoS Basic to load the following page.
Figure 2-3 Configuring Basic QoS in DSCP/802.1P Based Mode
Follow these steps to configure QoS in DSCP/802.1P based mode:
1) Select QoS mode as DSCP/802.1P Based.
QoS Mode Select the QoS mode.
DSCP/802.1P Based: In this mode, the IP packets are mapped to 4 priority
levels based on the DSCP value (Lowest= 0-15; Normal = 16-31; Medium
= 32-47; Highest = 48-63). The switch prioritizes packets with IP header
based on DSCP priority first. Then, the switch prioritizes packets with
VLAN tag but without IP header based on the PRI field. Finally, the switch
prioritizes packets without VLAN tag or IP header based on port priority.
2) Click Apply.
User Guide 66
Configuring QoS Configuring Bandwidth Control
3
Configuring Bandwidth Control
Choose the menu QoS > Bandwidth Control to load the following page.
Figure 3-1 Configuring Bandwidth Control
Follow these steps to configure bandwidth control:
1) Select the desired ports and configure the ingress rate and egress rate for the ports.
Ingress Rate
(Kbps)
Egress Rate
(Kbps)
LAG Displays the LAG which the port belongs to.
2) Click Apply.
Configure the bandwidth for receiving packets on the port. You can select a rate
from the drop-down list or select “Manual” to set Ingress rate, the system will
automatically select integral multiple of 64Kbps that is closest to the rate you
entered as the real ingress rate.
Configure the bandwidth for sending packets on the port. You can select a rate
from the drop-down list or select “Manual” to set egress rate, the system will
automatically select integral multiple of 64Kbps that is closest to the rate you
entered as the real egress rate.
User Guide
67
Configuring QoS Configuring Bandwidth Control
Note:
For a port, the ingress rate control feature and the storm control feature cannot be enabled
•
at the same time. If you enable ingress rate control for a port, storm control will be disabled
for that port automatically.
When egress rate is set for one or more ports, it is recommended to disable the flow control
•
on each port to ensure the switch works normally.
For ports in the same LAG, bandwidth control should be configured the same to ensure a
•
successful port aggregation.
User Guide 68
Configuring QoS Configuring Storm Control
4
Configuring Storm Control
Choose the menu QoS > Storm Control to load the following page.
Figure 4-1 Configuring Storm Control
Follow these steps to configure storm control:
1) Select the desired ports and configure the upper rate limit for forwarding broadcast
packets, multicast packets and UL-frames (Unknown unicast frames).
Bc Limit Enable or disable the broadcast control feature for the port.
Mc Limit Enable or disable the multicast control feature for the port.
UL Limit Enable or disable the UL-Frame (unknown unicast frame) control feature for the
port.
Rate (Kbps) Specify the upper rate limit for receiving the specified packet on the port. The
packet traffic exceeding the bandwidth will be discarded.
LAG Displays the LAG the port belongs to.
2) Click Apply.
User Guide
69
Configuring QoS Configuring Storm Control
Note:
For a port, the storm control feature and the ingress rate control feature cannot be enabled at
•
the same time. If you enable storm control for a port, ingress rate control will be disabled for
that port automatically.
For ports in the same LAG, storm control should be configured the same to ensure a success-
•
ful port aggregation.
User Guide 70
Configuring QoS Configuration Example for Basic QoS
5
Configuration Example for Basic QoS
5.1 Network Requirements
As shown below, both RD department and Marketing department can access the internet.
When congestion occurs, the traffic from two departments can both be forwarded and the
traffic from the Marketing department should take precedence.
Figure 5-1 Basic QoS Application Topology
Internet
Router
Port 3
RD Dept. Marketing Dept.
5.2 Configuration Scheme
To implement this requirement, you can configure QoS in port based mode to put the
packets from the Marketing department into the queue with the higher priority than the
packets from the RD department. Follow these procedures to configure QoS in port based
mode.
1) Enable port based mode.
Port 1
Port 2
Switch A
2) Map port 1 and port 2 to different priorities queues.
Demonstrated with TL-SG105E, the following section provides configuration steps.
User Guide
71
Configuring QoS Configuration Example for Basic QoS
5.3 Configuration Steps
1) Choose the menu QoS > QoS Basic to load the following page. In the Global Config
section, select QoS mode as Port Based. Click Apply.
Figure 5-2 Configuring Basic QoS in Port Based Mode
2) In the Port Based Priority Setting section, Set the priority queue for port 1 as
1(Lowest) and click Apply. Set the priority queue for port 2 as 4(Highest) and click
Apply.
Figure 5-3 Setting Different Priorities for Port 1 and Port 2
User Guide 72
Part 7
Configuring PoE
CHAPTERS
1. Overview
2. Configuring PoE
Configuring PoE Overview
1
Overview
Note
：
Only TL-SG1016PE supports the PoE configuration.
PoE (Power over Ethernet) is a remote power supply function. With this function, the switch
can supply power to the connected devices over twisted-pair cables.
Some devices such as IP phones, access points (APs) and cameras may be located far
away from the AC power source in actual use. PoE can provide power for these devices
without requiring to deploy power cables. This allows a single cable to provide both data
connection and electric power for the device.
PSE
Power sourcing equipment (PSE) is a device that provides power for PDs on the Ethernet,
for example, the PoE switch. PSE can detect the PDs and determine the device power
requirements.
PD
Powered device (PD) is a device receiving power from the PSE, for example, IP phones and
access points. According to whether PDs comply with IEEE standard, they can be classified
into standard PDs and non-standard PDs. Only standard PDs can be powered via TP-Link
PoE switches.
User Guide 74
Configuring PoE Configuring PoE
2
Configuring PoE
Choose the menu PoE > PoE config to load the following page.
Figure 2-1 Configuring PoE
Follow these steps to Configure PoE:
1) In the Global Config section, you can view the current PoE parameters. You can
configure the System Power Limit. Click Apply.
System Power
Limit
System Power
Consumption
System Power
Remain
2) In the Port Config section, select the ports you want to configure and specify the
parameters. Click Apply.
PoE Status Enable or disable the PoE function on corresponding port. The port can supply
PoE Priority Select the priority level for the corresponding port. When the supply power
Configure the maximum power the PoE switch can supply.
Displays the real-time system power consumption of the PoE switch.
Displays the real-time system remaining power of the PoE switch.
power to the PD when its status is enable.
exceeds the system power limit, the switch will power off PDs on low-priority
ports to ensure stable running of other PDs.
User Guide
75
Configuring PoE Configuring PoE
Power Limit
(0.1w-30w)
Power (w) Displays the real-time power supply of the port.
Current (mA) Displays the real-time current of the port.
Voltage (v) Displays the real-time voltage of the port.
PD Class Displays the class which the linked PD belongs to.
Power Status Displays real-time power status of the port.
Specify the maximum power the corresponding port can supply. The following
options are provided:
Class1: The maximum power that the port can supply is 4W.
Class2: The maximum power that the port can supply is 7W.
Class3: The maximum power that the port can supply is 15.4W.
Class4: The maximum power that the port can supply is 30W.
Manual: You can enter a value manually.
User Guide 76
Part 8
Searching Help
CHAPTERS
1. Help
2. Searching Online Help
3. Viewing Information About the Utility
Searching Help Help
1
Help
1.1 Overview
With the Help function, you can search for online help and view the information about the
utility.
1.2 Supported Features
Online Help
You can access the TP-Link support website and get the online user guide for the Easy
Smart Configuration Utility (the latest copy of this manual) and the products.
About
You can view the information about the utility, including the switch models supported by
the utility, the version of the utility software, and copyright information.
User Guide 78
Searching Help Searching Online Help
2
Searching Online Help
Choose the menu Help > Help to load the following page. You can click Online Help to
access the TP-Link support website and get the online user guide for the Easy Smart
Configuration Utility (the latest copy of this manual) and the products.
Figure 2-1 Searching Online Help
User Guide
79
Searching Help Viewing Information About the Utility
3
Viewing Information About the Utility
Choose the menu Help > About to load the following page. You can view the information
about the utility, including the switch models supported by the utility, the version of the
utility software, and copyright information.
Figure 3-1 Viewing Information About the Utility
User Guide 80
Loading...