Teac W-890R User Manual 2

3D0798550A

W-890R

Double Auto Reverse Cassette Deck

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH FRANÇAIS

ESPAÑOL

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

< Do not expose this apparatus to drips or splashes. < Do not place any objects filled with liquids, such as vases, on the

apparatus.

< Do not install this apparatus in a confined space such as a book

case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON position.

< The apparatus should be located close enough to the AC outlet

so that you can easily grasp the power cord plug at any time.

< The main plug is used as the disconnect device; the disconnect

device shall remain readily operable.

< Batteries (battery pack or batteries installed) shall not be

exposed to excessive heat such as sunshine, fire or the like.

< CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an incorrect type of battery. Replace only with the same or equivalent type.

< Excessive sound pressure from earphones and headphones can

cause hearing loss.

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

r Reorient or relocate the equipment and/or the receiving

antenna.

r Increase the separation between the equipment and receiver. r Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

r Consult the dealer or an experienced radio/TV technician for

help.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN.

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance will void the user’s warranty.

Manufactured under license from Dolby Laboratories. HX Pro headroom extension originated by Bang & Olufsen. Dolby, HX Pro, and the double-D symbol are trademarks of Dolby Laboratories.

Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.

Contents

Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit.

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction ..................................................5

Supplied accessories ........................................5

About this manual ..........................................5

Precautions and notes for placement and use ...............5

About cassette tapes .......................................5

Cassette tapes that you should not use ...................5

Automatic tape type detection function ..................6

Tape slack ................................................6

Accidental erasure prevention tabs ........................6

Maintenance ...............................................6

Connections ................................................7

Features of the W-890R .......................................8

Front panel .................................................8

Remote Control Unit ........................................9

Using the Remote Control Unit ..............................9

Cautions when using the remote control unit .............9

Loading batteries into the remote control unit ............9

Important Cautions for Handling Batteries .................9

Display ....................................................10

Playback ..................................................... 11

Playback I (either TAPE I or TAPE II ) .........................11

Playback II (either TAPE I or TAPE II) ........................12

Continuous playback ......................................13

RTZ I (TAPE I only) .........................................13

A-B Repeat playback .......................................13

Recording ...................................................14

Recording (either TAPE I or TAPE II) ........................14

To erase recordings ........................................15

Quick record start ..........................................15

Recording silence ..........................................15

Mic mixing recording ......................................16

Adjusting mix recording level ............................16

Continuous recording ......................................17

Parallel recording ..........................................18

Dubbing (from TAPE I to TAPE II) ........................... 18

Editing during dubbing (only at normal speed) .............19

Synchro reverse dubbing (from TAPE I to TAPE II) ...................20

Timer-Controlled Playback and Recording ....................21

Timer-Controlled Playback .................................21

Timer-controlled recording ................................21

Troubleshooting .............................................22

Connections with a timer ..................................22

Specifications ................................................23

Introduction

Before connecting and using the unit, please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the W-890R, as well as the operation of its many useful and convenient functions. After you have finished reading this manual, please keep it in a safe place for future reference

Dolby NR

Dolby NR is designed to reduce tape hiss, a noise introduced during the recording and playback processes. This cassette deck is equipped with Dolby B-type Noise Reduction. The Dolby NR system affects both recording and playback quality. In playback, be sure to set the DOLBY NR switch to the same position used when the recording was made.

Supplied accessories

In addition to this manual, the W-890R has been packed with the following:

< Remote control unit (RC-1277) x 1 < Batteries (AA) for remote control unit x 2 < Stereo RCA pin cable x 2 < Owner’s manual (this document) x 1 < Warranty card x 1

< When removing the power plug from the wall outlet, always pull

directory on the plug, never yank the cord. < The voltage selector on the rear panel is only available on units

for the North American market. Please set this to match your local

supply. If you are in any doubt in this matter, consult an electrician

NOTE

When transporting the unit, always use the original packing

materials. For this reason, we strongly recommend that you save all

the packing materials that came with the W-890R, in case you need

to transport it in the future. In addition, when transporting the unit,

you should tape the cassette decks closed, using an adhesive tape

that will not spoil the finish of the unit.

About cassette tapes

CAUTION

< Do not open the cassette or pull the tape out of the cassette. < Do not touch the tape surface. < Do not use or store the tape in a humid or dusty place. < Keep the tape away from any magnetic sources, such as speakers

or TVs, otherwise noise may be produced during playback or

important recordings may be erased.

ENGLISH

Contact your TEAC supplier if any of these items are missing.

About this manual

In this manual, we use the following conventions:

< The names of keys and controls are given in the following typeface:

EJECT.

< The alphanumeric portion of the display shows a message, this is

shown in the following typeface:

< If a preset indicator in the display (i.e. one which cannot change,

but is either on or off) is shown, this is shown as follows:

%2.

PARALLEL.

Precautions and notes for placement and use

The W-890R may be used in most areas, but to maintain top performance, and prolong operating life, observe the following notes, precautions and environmental conditions:

< Avoid exposing it to extremes of temperature and humidity and

avoid mechanical shocks and vibration.

< Keep the unit away from strong magnetic fields (TV sets, computer

monitors, large electric motors, etc.).

< The nominal temperature should be between 5°C and 35°C (41°F

and 95°F).

< Relative humidity should be 30 to 90 percent. < As the unit may become hot during operation, always leave

sufficient space above the unit for ventilation. Do not install this unit in a confined space such as a bookcase, and do not put anything on top of the unit.

< Avoid installing this unit on top of any heat-generating electrical

device such as a power amplifier.

< Make sure that the unit is mounted in a level position for correct

operation.

< Do not open the sealed cabinet as this might result in damage

to the circuitry or electrical shocks. If a foreign object should get inside the unit, contact your supplier or service agency.

Cassette tapes that you should not use

Poor performance, errors, or malfunctions may result if you use any of the tapes described below. Some of these tapes may also cause tape clog problems that can damage the tape transport mechanism.

Cassettes that are imperfectly shaped

Do not use a deformed cassette or one that has unstable tape movement or makes a strange sound during fast-forward or rewind.

Long play tapes

Tapes that are longer than 90 minutes are very thin and stretch easily, so using them can result in wow and flutter. In addition, long tapes can become tangled in the equipment, so please use caution with them.

Endless tapes

Do not use these tapes because they can easily get tangled in the tape transport mechanism.

Introduction

Automatic tape type detection function

This cassette deck can detect what type of tape is being used based on the detection holes in the cassette shell. Be sure to use cassettes with detection holes. With this cassette deck, you can play back normal (Type I), chrome (Type II) and metal (Type IV) tapes. For recording, use normal (Type I) or chrome (Type II) tapes. Each deck (TAPE I and TAPE II) is equipped with its own auto tape type detection function, so you can use different types of tape at the same time.

Metal

(

Type

(

Type

)

Type IV

CrO

Normal

Tape slack

Slack can cause the tape to get tangled in the capstan or other rotating parts. To prevent this, take up all tape slack using a pencil or the like inserted into the reel hole.

Automatic tape type detection holes

)

Maintenance

If the surface of the deck becomes soiled, wipe it clean with a dry, soft cloth. Never use volatile cleaners like thinners, benzine or alcohol because they will damage the surface finish. Do not allow the deck to remain in contact with rubber or vinyl products for a long period of time, as these could damage the surface finish.

CAUTION

For safety, always unplug the power cord before performing any maintenance.

< Cleaning the heads

If the head section gets dirty, the recording quality will deteriorate, resulting in degraded playback sound or “drops” in sound. Also, if the tape transport path gets dirty, the tape may get entangled in the rotating parts. It is therefore recommended that the heads, pinch rollers and capstans be cleaned regularly at intervals of 10-hour use with a cotton swab moistened with a commercially available, appropriate cleaning liquid.

NOTE

Do not make a recording or play back tape when the tape transport path is wet with cleaning liquid, as this could cause the tape to jam or clog.

Pinch roller

Capstan

Accidental erasure prevention tabs

Tabs on top of the cassette shell allow you to prevent important recordings from being erased by mistake. There are two tabs on each cassette shell: one for side “A” and the other for side “B”. Once these tabs have been removed using a screwdriver or the like, there is absolutely no chance of the recording function being activated. To record on a cassette whose tab has been broken off, stick a piece of adhesive tape over the hole. Be careful not to block the tape type detection holes.

Accidental erasure prevention tab for side “A”

Erase head

Record/playback head

Pinch roller

Capstan

Side “A”

Connections

LLRR

PLAYREC

TAPE

CAUTION

< Plug the power cord into an AC outlet only after having made all

other connections.

< Read the instructions of each component you intend to use with

this unit.



 Ê Ê>`Ê Ê"1/Ê>VÃ

Use RCA cables to make connections between this unit and your amplifier. Make sure to connect:

White plug to White jack (L: left channel) Red plug to Red jack (R: right channel)



231

 AC power cord

Plug this AC power cord into an AC wall socket.

NOTE

< Hold the power plug when plugging or unplugging the power

cord. Never pull or yank on the power cord. < Unplug the power cord when you are not going to use the unit for

some time.

ENGLISH

NOTE

Plugs must be firmly inserted into the corresponding jacks. Do not bundle the RCA cables together with the power cord and speaker cables. Doing so will degrade sound quality or generate noise.

 VOLTAGE SELECTOR

Switches the voltage to either 230 V or 120 V.

NOTE

< The voltage selector is not available on units for some

markets.

IN NORTH AMERICA

USE ONLY ON 120V SUPPLY

Front panel

Features of the W-890R

 POWER switch

This switches the unit power between off and on.

NOTE

The apparatus draws nominal non-operating power from the AC outlet with its POWER in the off position.

 TAPE I compartment

 RTZ key (TAPE I only)

This key returns the tape to the counter zero point.

 COUNTER RESET keys

Pressing these keys reset the tape counter readings for TAPE I and TAP E II, respectively.

 Synchro reverse key (SYNC REVERSE)

Pressing this key activates the synchro reverse dubbing function.

 REPEAT key

This allows repeat playback of a selected section of the tape.

 Display

This shows tape counters, level meters, etc.

 Parallel record key (PARALLEL REC)

This key lets you simultaneously record on both decks.

 Dubbing start key (DUB START)

This key is used when copying the contents of a tape from TAPE I to TAPE II, either at normal or high speed.

 TAPE II compartment

I Reverse mode switch (REV MODE)

This switch is used to switch between reverse modes.

O TIMER switch

This switch is provided for use with a commercially available audio timer, to allow timer controlled recording or playback. Normally, leave this switch to the OFF position.

= DOLBY NR switch

This switch toggles the Dolby Noise Reduction system on/off. In playback you need to set this switch to the same position as when the recording was made.

J EJECT (

Pressing these keys opens the TAPE I and TAPE II compartments.

L MIC jack and level control

Insert your microphone into this jack and use the knob to adjust the level of mic input.

NOTE

The MIC jack is mono. You cannot use a stereo microphone with this cassette deck.

Q Headphones jack (PHONES)

Plug your headphones into this jack.

M PITCH CONTROL

This control is used to vary the playback speed.

A REC LEVEL

This control is used to adjust the recording level.

) keys

Remote Control Unit

Using the Remote Control Unit

Cautions when using the remote control unit

< Point the remote control unit at the remote sensor of the cassette

deck and operate the remote control unit at a distance of no more

than 5 meters. Do not place objects between the remote control

unit and remote sensor. < Direct sunlight or very bright light will reduce the sensitivity of the

remote sensor. If this is the case, use the control buttons on the

cassette deck instead of the remote buttons. < It is possible that other infrared-ray-sensitive equipment nearby

may malfunction when you operate the remote control.

Loading batteries into the remote control unit

Remove the lid of the battery compartment, load two “AA” sized batteries in the indicated directions, and then replace the lid. When inserting batteries, be sure to observe proper polarity (+ and –).

ENGLISH

G Tape transport control keys

RECORD (K) key

Pressing this key shifts the corresponding deck to record-pause mode.

PAUSE (J) key

Pressing this key temporarily stops playback or recording.

Recording mute (REC MUTE) key

This key is for creating the 4-second blank space.

m/, key

Fast-forward/Rewind

STOP (H) key

Stop of playback/record

PLAY (h / y) key

Reverse side play/Forward side play

HRemote sensor

When operating the remote control unit, point it towards here.

If you have to put the remote control unit quite close to the remote sensor or if any remote buttons do not work, then the batteries are no longer fit for use and must be replaced. Be sure to always replace both batteries at once.

Important Cautions for Handling Batteries

Improper battery use can result in leakage or rupture. Observe the following instructions:

< Load the batteries in the correct direction as indicated in the

battery compartment. < Do not mix old and new batteries, or mix different types or brands

of battery.

< Do not heat, disassemble, or throw batteries into fire or water. < Do not store or carry batteries together with other small metal

objects. Doing so can cause battery shorting, leakage or rupture.

< Do not try to recharge dry batteries. < When the cassette deck is not going to be used for a long time

(more than one month), take the batteries out of the battery

compartment. < If leakage into the battery compartment is observed, wipe up any

liquid inside the compartment and load new batteries.

Display

Features of the W-890R

 Peak level meter

This shows recording and playback levels.

 SYNC REV

This indicator lights when the synchro reverse dubbing function is switched on.

 PARALLEL

This indicator lights to indicate parallel recording is taking place.

 Playback/recording direction indicator of TAPE I deck

 Pause indicator

This indicator lights when the TAPE I deck is temporarily stopped.

 Tape counter of TAPE I deck

The tape counter indicates the relative position of the tape. You can reset the counter to zero whenever you want. When an A-B repeat operation is on,

 Record indicator

This indicator lights when the TAPE I deck is in record mode.

 Play indicator

This indicator lights when the TAPE I deck is in play mode.

4' is shown.

 Dubbing indicator

NORMAL DUB lights during normal speed dubbing, and HIGH DUB

lights during high speed dubbing.

 Play indicator

This indicator lights when the TAPE II deck is in play mode.

I Record indicator

This indicator lights when the TAPE II deck is in record mode.

O Tape counter of TAPE II deck

The tape counter indicates the relative position of the tape. You can reset the counter to zero whenever you want. When an A-B repeat operation is on,

= Pause indicator

This indicator lights when the TAPE II deck is temporarily stopped.

J Playback/recording direction indicator of TAPE II deck

4' is shown.

Playback I (either TAPE I or TAPE II )

Switch on the POWER.

Playback

Set the DOLBY NR switch.

Press the PLAY (h or y) key.

Set the switch to the ON position when playing back tapes recorded with Dolby NR. To play tapes recorded without Dolby NR, set the switch to the

OFF position.

ENGLISH

Load a pre-recorded tape into the TAPE I or II deck.

Press the EJECT key (L) to open the cassette compartment. Insert the cassette tape with its open edge facing down, the desired side facing you. Then, close the cassette compartment by pushing on its front part.

Side “A” facing you

This cassette deck can play back Normal (Type I), Chrome (Type II) and Metal (Type IV) tapes. For the sake of simplicity, we refer to the tape side facing you as Side “A” and to the tape side facing away as Side “B”. When you insert a cassette with Sides “A” and “B” reversed, Side “A” should read Side “B” and Side “B” should read Side “A”.

Select a reverse mode setting using the REV MODE switch.

Pressing the y key starts playback from side “A”. Pressing the h key starts playback from side “B”.

You have a choice of three settings:

7: One way mode

Set the switch to this position to playback only one side.

j: Two way mode

Set the switch to this position to play back both sides of the tape in one session. When playback reaches the end of side “A”, the playback direction is automatically reversed, and playback continues on side “B”.

p: Repeat mode

Set the switch to this position. Both sides of the tape are played back as many as 5 times. If a tape is in both the TAPE I and TAPE II compartments, the TAPE I and TAPE II decks continuously play the tapes.

Playback II (either TAPE I or TAPE II)

To stop playback, press the STOP (H) key.

To stop playback temporarily, press the PAUSE key. To

resume playback, press the PAUSE key again, or press the PLAY (h or y) key.

Playback

Pitch control (TAPE I deck only)

This control varies the pitch of the music during playback (This

control does not work during recording or dubbing).

To listen through headphones

WARN ING

Turning the PITCH CONTROL knob clockwise increases the playback speed and raises the pitch up to +10%. Turning the PITCH CONTROL knob counterclockwise reduces the playback speed and lowers the pitch by a maximum of –10%.

There is no level control for the headphones output. Beware that sudden loud sounds may occur depending on recorded material. You should avoid prolonged exposure to high volume sound as this can damage your hearing.

While playback is paused, pressing the PLAY key whose direction is opposite to the indicator (h or y) on the display, will switch the playback direction. This does not release the pause function. Press PAUSE or the same play key (h or y) again to start playback on the other side of the tape.

Fast forward/Rewind

Press the m or , key while in stop mode to fast wind the tape.

To stop the fast winding tape, press the STOP (H) key.

Tape counter Press the COUNTER RESET key to reset the tape counter to

. You can use this function for easy relocation of any

desired point on the tape.

Plug your headphones into the PHONES jack, and put on the headphones.

Plugging into the PHONES jack does not disable the line outputs.

Continuous playback



Continuous playback can be performed between TAPE I and TAPE II. When one tape is played back to the end, the other tape automatically starts playback, in a relay fashion.

Load pre-recorded tapes into the TAPE I and TAPE II

compartments.

Set the DOLBY NR switch.

Always set the DOLBY NR switch to the same position that was used for recording.

Set the REV MODE switch to the p(CONT PLAY) position.

RTZ I (TAPE I only)

When you press the RTZI key, the TAPE I deck fast-forwards or rewinds the tape until the counter reads

NOTE

< RTZ (Return-to-zero) only works on TAPEI. < If the counter position is too close to the 0000 mark (greater than

9994 or less than 0005), the RTZ function cannot be used.

, and then stops.

A-B Repeat playback

ENGLISH

Press the PLAY (h or y) key of the deck you want to start

first.

You can start continuous playback from either TAPE I or TAPE II. Playback cycles through four tape sides as follows, and will continue as many as 5 times when you start the playback from Side “A” on TAPE I, or until you stop the operation.

TAPE I Side“A” w Side “B” 2 x TAPE II Side “B” s Side “A”

1. During playback, press the REPEAT key at the point where you want to start the repeat playback interval (A point).

4' appears on the display when this point is set.

2. Next, press the REPEAT key at the point where you want to end the repeat playback interval (B point). 4'appears on the display. The tape automatically rewinds to the A point where playback restarts. When the B point is reached, playback stops temporarily, the tape rewinds again to the A point, and playback continues to repeat.

3. Press the STOP (H) key to end repeat playback.

CAUTION

< During repeat playback, only the REPEAT and STOP keys can be

used.

< This function cannot be used for durations of less than 10 counts

on the tape counter between the starting and end points.

< Only intervals in the current playback direction can be repeated. < Repeat playback stops automatically after 20 repetitions.

Recording (either TAPE I or TAPE II)

Turn on the power.

Load a tape for recording.

Recording

Press the RECORD (K) key.

The deck enters the record-pause mode. J and will light on the display.

NOTE

< If you want to record using the remote control unit, press the two

RECORD keys on the remote control unit at the same time.

< To stop recording while the deck is in the record-pause mode,

press the STOP key (H).

Adjust the recording level.

Side “A” facing you

Press the EJECT (L) key to open the cassette compartment. Insert the cassette tape with its open edge facing down, side “A” facing you. Then close the cassette compartment by pushing in the cassette door until it clicks shut.

NOTE

< If the erasure prevention tabs of the loaded cassette tape have

been broken off, stick a piece of adhesive tape over the hole(s).

< With this cassette deck you can use Normal (Type I) and Chrome

(Type II) tapes for recording.

Set the REV MODE switch.

7 : Set to this position to record on one side only. j : Set to either of these positions to record on both sides.

Set the DOLBY NR switch.

Start playback of your recording source and set the REC LEVEL control knob so that the level meter indicates “0 dB” at peaks.

Set the recording direction. (To record on only one side of

the tape)

Recording is made in the direction indicated by the play/record direction indicator (h / y). To change this direction, press the opposite direction PLAY (h or y) key.

NOTE

Make sure that the arrow on the key (h / y) you are going to press points in the opposite direction of the arrow on the indicator (h / y) shown on the display. Failure to follow this instruction causes the deck to start recording in an unintended direction.

Set the switch to ON to record with Dolby Noise Reduction. Set to OFF to record without Dolby Noise Reduction.

When everything is ready, start recording by pressing the

PAUSE key or the PLAY key whose arrow points in the same direction as the indicator.

To record on both tape sides, set the REV MODE switch to j or p and press the forward PLAY (y) key. If you press the reverse PLAY (h) key, recording will be done only on side “B”. To stop recording, press the STOP (H) key.

To stop recording temporarily

Recording silence

When you press the REC MUTE key during recording, the unit records no signal for about 4 seconds and then enters the record-pause mode. To resume recording, press the PAUS E key.

ENGLISH

Press the PAUS E key to stop recording temporarily. A second press of the key resumes recording.

To erase recordings

When you make a recording, the tape is overwritten (previous recording is erased). To erase a tape without making a new recording, set the REC LEVEL control to the minimum (0) position and press the RECORD (K) key followed by the PLAY (h or y) key.

Quick record start

Press the RECORD (K) key and press the PLAY (h or y) key corresponding to the direction you want the tape to run.

< To create a blank of more than 4 seconds long

Hold down the REC MUTE key for the desired length of time. When you release the key, the deck enters the record-pause mode.

< To create a blank of less than 4 seconds long

Press the PAUS E key within 3 seconds of pressing the REC MUTE key.

NOTE

If you press the REC MUTE key when the deck is in the recordpause mode, no signal is recorded for about 4 seconds, and then the deck shifts back to the record-pause mode.

Recording

Mic mixing recording

This function allows you to record your voice and another audio source together on a cassette tape. The mic sound is fed into both the Left and Right channels so it is located in the center of the stereo image. You have the choice of either selecting the audio source you want on the amplifier connected to the LINE IN jacks of the deck, or plugging the desired source directly into the deck’s LINE IN jacks.

NOTE

< To prevent feedback (howling), disable the speaker outputs from

the amplifier. Use headphones to monitor recording.

< This cassette deck is not compatible with stereo mics. Always use a

mono mic.

Adjusting mix recording level

To record a mix of voice and another audio source, you need to adjust the mic input level and then fine tune the overall recording level.

1. Plug your microphone into the MIC jack on the front panel.

2. Start playing the audio source, switch the deck into the record-pause mode (by pressing the RECORD (K) key), and temporarily adjust the REC LEVEL control to a relatively low level.

3. Speak into the mic and adjust the MIC level control to get the optimum balance between your voice and the other source.

4. Fine tune the overall recording level using the REC LEVEL control so that the level meter reads 0 dB at peaks.

5. When everything is ready, start recording as instructed earlier in this manual.

Adjustment of

mic input level

Audio source

Adjustment of overall recording level

Continuous recording

This function allows you to make uninterrupted recordings on both sides of two tapes.

Load cassette tapes for recording into the TAPE I and

TAP E II compartments.

NOTE

Be careful not to press the PLAY (h or y) key whose arrow points in the same direction as the indicator. Doing so will start recording.

Recording is done in this order:

TAP E I Side “A” x Side “B” x TAP E II Side “A” x Side “B”

You can start recording from side “B” of TAPE I. But if you do so, side “A” of this tape is not recorded: when recording reaches the end of side “B”, the TAPE II deck starts recording.

NOTE

The TAPE II deck always starts recording from side “A”.

Start recording.

ENGLISH

Side “A” facing you

Set the REV MODE switch to the p (CONT REC/PLAY)

position.

Set the DOLBY NR switch to the ON position if you want to.

Press the TAPE I deck’s RECORD (K) key.

The deck enters the record-pause mode. J and will light on the display. Now adjust the recording level and any other settings, as required.

Check the recording direction.

Recording starts when you press the PAUSE key or the PLAY (h or y) key whose arrow points in the same direction as the indicator on the TAPE I deck. When recording is finished on the TAPE I deck, the TAPE II deck automatically starts recording.

NOTE

The transition from TAPE I to TAPE II takes several seconds.

To stop recording

Press the STOP (H) key of the deck which is currently recording.

If an indicator is lit which points in the direction opposite to the one desired, change the direction by pressing the opposite direction PLAY (h or y) key.

Recording

Parallel recording

This function allows you to record the same material simultaneously on both TAPE I and TAPE II. Load tapes into both decks and press the PARALLEL REC key to start recording. Before starting recording, check and correct the following by performing steps 1 – 7 on page 14 such as Record direction, Reverse mode setting, Dolby NR setting, Recording level, etc. When everything is ready, get back into stop mode if the deck is in another mode. During parallel recording, the During parallel recording, only the following keys work:

TAE P I deck : STOP (H) TAP E II deck : PAUSE , REC MUTE, STOP (H)

Pressing the STOP (H) key on either deck stops both tapes at once.

PARALLEL indicator is lit on the display.

Dubbing (from TAPE I to TAPE II)

Insert a cassette tape for playback into the TAPE I

compartment and a cassette tape for recording into the TAP E II compartment.

Side “A” facing you

Set the tape transport direction on both decks.

If the play/record direction indicator (h / y) on the display points in the direction opposite to the one desired, press the PAUS E key followed by the PLAY (h or y) key corresponding to the desired direction. After changing the tape transport direction, be sure to press the

STOP (H) key to get out of the pause mode.

NOTE

< Be careful not to press the PLAY (h or y) key whose arrow

points in the same direction as the indicator. Doing so will start playback.

< Set the REV MODE switch as required. < You don’t need to adjust the recording level or set the Dolby NR

system, as both depend on the pre-recorded source tape.

Press either DUB START key to start dubbing.

normal speed high-speed dubbing start dubbing start

For normal speed dubbing, press the NORMAL key. For highspeed dubbing, press the HIGH key.

NOTE

High-speed dubbing makes a copy at approximately two times the normal speed. We recommend normal speed dubbing for best audio quality. During dubbing, either the steadily on the display.

During normal speed dubbing, only the following keys work:

TAE P I deck : STOP (H) TAP E II deck : PAUSE , REC MUTE, STOP (H)

During high-speed dubbing, only the STOP (H) key works.

NORM DUB or HIGH DUB indicator lights

Editing during dubbing (only at normal speed)

Neither DUB START key works immediately after the tape is fastforwarded or rewound to the end. Wait for 5 seconds or more before pressing the key.

NOTE

< During dubbing, the pitch control does not work. < Recording level adjustment is not necessary for dubbing, as

the recording level is set to the level of the pre-recorded tape. Operating the REC LEVEL control, before or after starting dubbing, has no effect at all.

< If a nearby television set is switched on during high-speed

dubbing, a high-pitched interference noise may be recorded on the tape. To avoid this, either perform dubbing at normal speed, or turn off the television.

< If you want to start dubbing using the remote control unit, press

the two DUB START keys (NORMAL keys or HIGH keys), for either normal or high speed dubbing, on the remote control unit at the same time.

You can prevent unwanted songs or unnecessarily long blanks from being dubbed, or you can create blanks between songs.

1. At the desired point during dubbing, press the PAUSE key on the TAPE I deck. The TAPE II deck only enters the pause mode, allowing you to let unwanted songs go by.

To create a 4-second blank between songs, press the REC MUTE key on the TAPE II deck. The TAPE II deck temporarily stops after recording no signal for 4 seconds. The TAPE I deck continues playback when the TAPE II deck is in pause mode.

2. To resume dubbing, press the PAUSE key on the TAPE II deck.

ENGLISH

Recording

Synchro reverse dubbing (from TAPE I to TAPE II)

When you use this dubbing function and a shorter tape reaches the end of side “A”, it momentarily stops until the other tape reaches the end of side “A”. Then both tapes automatically switch over to side “B” and recording and playback re-start simultaneously.

If TAPE I is shorter than TAPE II

When TAPE I reaches the end of side “A”, TAPE I stops and TAPE II enters the “blank recording” mode. When TAPE II reaches the end, both TAPE I and II are reversed simultaneously. TAPE I starts playback and TAPE II resumes recording. When TAPE I reaches the end of side “B”, both TAPE I and II stop simultaneously.

If TAPE II is longer than TAPE I

When TAPE II reaches the end of side “A”, TAPE II enters the recordpause mode, while TAPE I continues playback. When TAPE I reaches the end, both TAPE I and II are reversed simultaneously. TAPE I starts playback and TAPE II resumes recording. When TAPE II reaches the end of side “B”, both TAPE I and II stop simultaneously.

Insert a cassette tape for playback into the TAPE I

compartment and a cassette tape for recording into the TAP E II compartment.

Side “A” facing you

Set the REV MODE switch to the two-way (j) position.

Check the recording direction of both decks.

If the reverse direction indicator (h) lights on the display, press the PAU SE key followed by the forward PLAY (y) key. Then, be sure to press the STOP (H) key to get out of the pause mode.

NOTE

< Be careful not to press the PLAY (h or y) key whose arrow

points in the same direction as the indicator. Doing so will start playback.

< You do not need to adjust the recording level or set the Dolby NR

system, as both depend on the pre-recorded source tape.

Press the SYNC REVERSE key.

The SYNC REV indicator will light on the display. The SYNC REVERSE key does not work if the reverse mode is set to any positions other than j or if the transport direction of both decks is set to reverse (h).

Press either DUB START key to start dubbing.

normal speed high-speed dubbing start dubbing start

For normal speed dubbing, press the NORMAL key. For highspeed dubbing, press the HIGH key. High-speed dubbing makes a copy at approximately two times the normal speed. We recommend normal speed dubbing for best audio quality. During dubbing, either the steadily on the display. During normal speed dubbing, only the following keys work:

TAP E I deck : STOP (H)

TAP E II deck : PAUSE, REC MUTE, STOP (H) During high-speed dubbing, only the STOP (H) key works. Pressing the STOP (H) key on either deck stops both tapes at once. Neither DUB START key works immediately after the tape is fastforwarded or rewound to the end. Wait for 5 seconds or more before pressing the key.

NORM DUB or HIGH DUB indicator lights

NOTE

< During dubbing, the pitch control does notwork. < Recording level adjustment is not necessary for dubbing, as

the recording level is set to the level of the pre-recorded tape. Operating the REC LEVEL control, before or after starting dubbing, has no effect at all.

< If a nearby television set is switched on during high-speed

dubbing, a high-pitched interference noise may be recorded on the tape. To avoid this, either perform dubbing at normal speed, or turn off the television.

+ 44 hidden pages