Spektrum SPM2300 DX2E User Manual [en, de, fr, it]

®
ST. RATE
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc.
For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
EN
WARNING AGAINST COUNTERFEIT PRODUCTS: Thank you for purchasing a genuine Spektrum product. Always
purchase from a Horizon Hobby, Inc. authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, Inc. disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum.
Age Recommendation: Not for Children under 14 years. This is not a toy.
NOTICE: This product is only intended for use with
unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.
INSTALLING THE TRANSMITTER BATTERIES
FRANCE RF SETTING:
The DX2E has a France RF setting that complies with French regulations. When in France, always use the France power setting when operating the transmitter outdoors.
WARRANTY REGISTRATION
Visit www.spektrumrc.com/registration today to register your product.
BATTERY LED MONITOR
POWER
Solid Green Battery is good (Above 4V) Flashing Green Battery voltage is critically low. Replace batteries
(below 4V)
ST. TRIM
SPEKTRUM DX2E USER GUIDE
1
EN
RECEIVER COMPATIBILITY
The DX2E is compatible with all Spektrum™ DSM®, DSM2™ and Marine surface receivers.
RECEIVER CONNECTION AND INSTALLATION
Antenna LED
SR200
THR STR BIND
Throttle Port Steering Port Bind/Battery Port Bind Plug
1. With the receiver off, insert the bind plug into the BIND port on the receiver.
2. Power the receiver through any other port. The green LED will flash continuously, indicating the receiver is in bind mode.
3. With the steering wheel and throttle trigger in the desired preset failsafe positions (see the Failsafe section on this page for more information), press and hold the bind button and turn on the transmitter. The green LED on the front of the transmitter will flash within three seconds, indicating the transmitter is in bind mode. Release the bind button when the green LED flashes. Continue to hold the failsafe positions until the binding process is complete.
Bind Button
Typical Electric Installation
2.4Ghz DSM
SR200
SPORT SURFACE
RECEIVER
Receiver
Battery
Electronic
Speed Control
THR
STR
BIND
Steering Servo
To Motor
Typical Gas Installation
Receiver
2.4Ghz DSM
SR200
THR
SPORT SURFACE
RECEIVER
STR
BIND
Install the Receiver in your vehicle using double-sided foam servo tape. Foam servo tape will hold the receiver in place and help isolate it from vibrations. Mount the antenna up and away from the vehicle in an antenna tube. The higher up the antenna is, the better signal it will receive.
NOTICE: Do not cut the antenna.
Throttle Servo
Steering Servo
Battery
BINDING A RECEIVER
Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. When a receiver is bound to a transmitter, the receiver will only respond to that specific transmitter. The DX2E and SR200 are bound at the factory, but if you need to rebind for any reason, please follow these steps:
BIND THST
N R N R
4. The LED on the receiver will glow solid when the transmitter and receiver are bound.
5. Remove the bind plug and store it in a convenient place.
You must rebind when:
• Differentfailsafepositionsaredesirede.g.,whenthrottle or steering reversing has been changed.
• Changingreceivertypese.g.,changingfromaDSM receiver to a DSM2 or Marine receiver.
• Bindingthereceivertoadifferenttransmitter.
Some Spektrum receivers, like the SR3001, use a bind button rather than a bind plug. The binding process is the same with this receiver; however, instead of inserting the plug before powering up the receiver, press and hold the bind button while powering up the receiver to enter bind mode.
FAILSAFE
Failsafe positions are also set during binding. In the unlikely event that the radio link is lost during use, the receiver will drive the servos to their preprogrammed failsafe positions (normally full brakes and straight steering). If the receiver is turned on prior to turning on the transmitter, the receiver will enter failsafe mode. When the transmitter is turned on, normal control is resumed. For more information on setting the failsafe, refer to the Binding a Receiver section above.
SERVO REVERSING
If a right steering command does not result in the wheels turning right (and vice versa), the channel may need to be reversed. To reverse a channel, switch the position of the correlating switch—“N” is for normal, “R” is for reverse. You can use a small screwdriver to move the switch if necessary.
2 SPEKTRUM DX2E USER GUIDE
Reverse Switch
ST. RATE
ST. RATE
Steering
Reverse Switch Throttle
EN
Steering Rate Dial
BIND THST
N R N R
STEERING TRIM
The steering trim dial is used to adjust the steering trim when the wheel is centered. Rotating the dial changes the steering trim (the steering at rest position). Normally, the steering trim is adjusted until the vehicle tracks straight.
Steering Trim Dial
ST. TRIM
POWER
TH. TRIM
THROTTLE TRIM
The throttle trim dial is used to adjust the throttle trim when the throttle stick is released (neutral position). This is typically used to adjust the brakes. Rotating the dial causes the throttle trim (the throttle position at rest) to be changed.
Throttle Trim Dial
ST. TRIM
POWER
TH. TRIM
STEERING RATE
Steering rate (also known as dual rate) allows on-the-fly steering travel adjustments to be made using the steering rate dial. Steering rate limits the amount of travel of the steering servo. The steering rate cannot be greater than 100%.
ST. RATE
RF MODE
The DX2E has a France RF Mode that complies with French regulations. The DX2E must be in France mode when used outdoors in France. At all other times, the transmitter should be in Standard mode.
FRANCE MODE
Turn the wheel full left, pull the trigger full throttle and hold down the bind button while turning on the transmitter. The Green LED will flash twice.
STANDARD MODE
Turn the wheel full right, pull the trigger full throttle and hold down the bind button while turning on the transmitter. The Green LED will flash once.
GENERAL NOTES
Radio controlled models are a great source of pleasure. Unfortunately, they can also pose a potential hazard if not operated and maintained properly. It is imperative to install your radio control system correctly. Additionally, your level of operating competency must be high enough to ensure you are able to control your model under all conditions. If you are a newcomer to radio controlled models, please seek help from an experienced modeler or your local hobby shop.
SAFETY POINTS TO OBEY FOR MODELERS
• Ensureyourbatteries(bothtransmitterandreceiver) have been properly charged for your model.
• Checkallservosandtheirconnectionspriortoeachrun.
• Donotoperateyourmodelnearspectators,parkingareas
or any other area that could result in injury to people or damage of property.
• Donotoperateyourmodelduringadverseweather
conditions. Poor visibility can cause disorientation and loss of control of your model.
• Donotpointthetransmitterantennadirectlytowardthe
model. The radiation pattern from the tip of the antenna is inherently low.
• Donottakechances.Ifatanytimeduringtheoperation of your model you observe any erratic or abnormal operation, immediately stop operation of your model until the cause of the problem has been ascertained and corrected. Safety can never be taken lightly.
SPEKTRUM DX2E USER GUIDE
3
EN
2.4GHz TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
The system will not connect
The receiver goes into failsafe mode a short distance away from the transmitter
The receiver quits responding during operation
Your transmitter and receiver are too close together
You are around metal objects Move to an area with less metal
The model selected is not the model bound to Check model selected and ensure you are bound to
Your transmitter was accidentally put into bind mode and is no longer bound to your receiver
Check the receiver antenna to be sure it is not cut or damaged
Inadequate battery voltage Charge batteries. Spektrum receivers require at least
Loose or damaged wires or connectors between battery and receiver
Move transmitter 8 to 12 feet from receiver
that model
Rebind your transmitter and receiver
Replace the receiver or contact Horizon Product Support
Make sure your receiver antenna is in an antenna tube and is above the vehicle
3.5V to operate. An inadequate power supply can allow voltage to momentarily drop below 3.5V and cause the receiver to brown out and reconnect
Check the wires and connection between the ba­ttery and receiver. Repair or replace wires and/or connectors
FCC INFORMATION
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
ANTENNA SEPARATION DISTANCE
When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
The following illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum transmitter.
1-YEAR LIMITED WARRANTY
WHAT THIS WARRANTY COVERS
Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 year from the date of purchase by the Purchaser.
WHAT IS NOT COVERED
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, or (v) Products not purchased from an authorized Horizon dealer.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
PURCHASER’S REMEDY
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
4 SPEKTRUM DX2E USER GUIDE
LIMITATION OF LIABILITY
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
LAW
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
QUESTIONS, ASSISTANCE, AND SERVICES
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@horizonhobby. com, or call 877.504.0233 toll free to speak to a Product Support representative. You may also find information on our website at www.horizonhobby.com.
INSPECTION OR SERVICES
If this Product needs to be inspected or serviced, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may
be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com under the Support tab. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.
WARRANTY REQUIREMENTS
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your
Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
NON-WARRANTY SERVICE
Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/Service/Request/.
WARRANTY AND SERVICE CONTACT INFORMATION
Country of Purchase Horizon Hobby Address Phone Number/Email Address
United States of America
United Kingdom Horizon Hobby Limited Units 1-4 Ployters Rd
Germany Horizon Technischer Service Christian-Junge-Straße 1
France Horizon Hobby SAS 14 Rue Gustave Eiffel
China Horizon Hobby China Room 506, No. 97 Changshou Rd.
Horizon Service Center (Electronics and engines)
Horizon Product Support (All other products)
4105 Fieldstone Rd Champaign, Illinois, 61822 USA
4105 Fieldstone Rd Champaign, Illinois, 61822 USA
Staple Tye, Harlow, Essex CM18 7NS, United Kingdom
25337 Elmshorn, Germany
Zone d’Activité du Réveil Matin 91230 Montgeron
Shanghai, China 200060
877-504-0233 Online Repair Request: visit www.horizonhobby.com/service
877-504-0233 productsupport@horizonhobby.com
+44 (0) 1279 641 097 sales@horizonhobby.co.uk
+49 (0) 4121 2655 100 service@horizonhobby.de
+33 (0) 1 60 47 44 70 infofrance@horizonhobby.com
+86 (021) 5180 9868 info@horizonhobby.com.cn
EN
SPEKTRUM DX2E USER GUIDE
5
EN
PARTS CONTACT INFORMATION
Country of Purchase Horizon Hobby Address Phone Number/Email Address
United States Sales
United Kingdom Horizon Hobby Limited
Germany Horizon Hobby GmbH
France Horizon Hobby SAS
China Horizon Hobby China
4105 Fieldstone Rd Champaign, Illinois, 61822 USA
Units 1-4 Ployters Rd Staple Tye Harlow, Essex CM18 7NS, United Kingdom
Christian-Junge-Straße 1 25337 Elmshorn, Germany
14 Rue Gustave Eiffel Zone d’Activité du Réveil Matin 91230 Montgeron
Room 506, No. 97 Changshou Rd. Shanghai, China 200060
800-338-4639 sales@horizonhobby.com
+44 (0) 1279 641 097 sales@horizonhobby.co.uk
+49 4121 46199 60 service@horizonhobby.de
+33 (0) 1 60 47 44 70 infofrance@horizonhobby.com
+86 (021) 5180 9868 info@horizonhobby.com.cn
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2012010601 Product(s): Spektrum DX2E/
Item Number(s): SPMR2300, SPM2300 Equipment class: 2 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:
EN 300-328 V1.7.1 EN 301 489-1 V1.7.1: 2006 EN 301 489-17 V1.3.2: 2008 EN 60950-1:2006+A11
Signed for and on behalf of: Horizon Hobby, Inc. Champaign, IL USA January 6, 2011
Spektrum DX2E with SR200
International Operations and Risk Management
Horizon Hobby, Inc.
waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equip­ment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
Steven A. Hall
Vice President
6 SPEKTRUM DX2E USER GUIDE
DE
ST. RATE
HINWEIS:
Alle Anweisungen, Garantien und dazugehörigen Dokumente können ohne Ankündigung von Horizon Hobby Inc. geändert
werden. Eine aktuelle Version ersehen Sie bitte im Support Feld unter: http://www.horizonhobby.com
Erklärung der Begriffe
Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen: HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe oder keine Gefahr von Verletzungen ergeben. ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die Gefahr von schweren Verletzungen. WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden, Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberflächliche Verletzungen.
WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen vertraut
zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem Eigentum führen oder schwere Verletzungen verursachen.
Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug. Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwachsenen. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, Inc., das Produkt zu zerlegen, es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben werden kann und Schäden oder schwere Verletzungen vermieden werden.
WARNUNG ZU GEFÄLSCHTEN PRODUKTEN: Vielen
Dank, dass Sie sich dieses Spektrum Produkt gekauft haben.
EINSETZEN DER SENDERBATTERIEN
Bitte kaufen Sie Ihre Spektrum Produkte immer von einem autorisiertem Händler um sicherzu stellen, dass Sie ein authentisches hochqualitatives original Spektrum Produkt gekauft haben. Horizon Hobby lehnt jede Unterstützung, Service oder Garantieleistung von gefälschten Produkten oder Produkten ab die von sich in Anspruch nehmen kompatibel mit Spektrum oder DSM zu sein.
Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.
HINWEIS: Dieses Produkt ist ausschließlich für die
Verwendung in unbemannten ferngesteuerten Fahrzeugen
BATTERY LED MONITOR
und Fluggeräten im Hobbybereich vorgesehen. Horizon Hobby lehnt jede Haftung und Garantieleistung ausserhalb der vorgesehen Verwendung ab.
RF EINSTELLUNG FRANKREICH
POWER
ST. TRIM
Die DX2E hat eine französische RF Einstellung die mit den Bestimmungen in Frankreich kompatibel ist. Bitte benutzen Sie wenn Sie in Frankreich den Sender im Freien betreiben immer diese Einstellung.
GARANTIEREGISTRIERUNG
Grün Batterie ist OK (über 4V) Grün blinkt Batteriespannung ist kritisch niedrig. Ersetzen Sie die Batterien. (unter 4 Volt)
Registrieren Sie bitte heute Ihr Produkt unter www.spektrumrc.com/registration.
®
SPEKTRUM DX2E Bedienungsanleitung
7
DE
EMPFÄNGER KOMPATIBILITÄT
Die DX2E ist kompatibel mit allen Spektrum™ DSM, DSM2™ und Marine Empfängern.
EMPFÄNGEREINBAU UND ANSCHLÜSSE
Antenne LED
SR200
THR STR BIND
TYPISCHER ELEKTROEINBAU
Akku
Elektronischer
Empfänger
2.4Ghz DSM
SR200
SPORT SURFACE
RECEIVER
THR
STR
BIND
Fahrtenregler
Lenkservo
TYPISCHER VERBRENNEREINBAU
Empfänger
2.4Ghz DSM
SR200
THR
SPORT SURFACE
RECEIVER
STR
BIND
Befestigen Sie den Empfänger mit doppelseitigen Schaumklebeband. Das Klebeband hält den Empfänger in Position und schützt ihn vor Vibrationen. Schieben Sie die Antenne in ein Antennenröhrchen und stellen dieses aufrecht. Je höher die Antenne steht, desto besser wird sie das Signal empfangen.
HINWEIS: Schneiden oder kürzen Sie die Antenne nicht.
Anschluß Gas Anschluß Lenkung Bindestecker/
Akkuanschluß Bindestecker
Zum Motor
Gasservo
Lenkservo
Akku
1. Stecken Sie mit ausgeschalteten Empfänger den Bindestecker in den Bindeanschluß des Empfängers.
2. Schalten Sie den Empfänger durch einen beliebigen anderen Anschluß ein. Die grüne LED blinkt und zeigt damit den Binde Mode an.
3. Mit dem Gashebel und Lenkrad in den gewünschten Preset Failsafepositionen (siehe dazu den Abschnitt Failsafe auf dieser Seite) drücken und halten Sie den Bindeknopf gedrückt und schalten den Sender ein. Die grüne LED auf der Vorderseite des Senders blinkt innerhalb von drei Sekunden und zeigt damit an, dass sich der Sender im Bindemode befindet. Lassen Sie den Knopf los wenn die grüne LED blinkt. Halten Sie die Failsafepositionen bis der Bindevorgang durchgeführt ist.
Bindeknopf
BIND THST
N R N R
4. Die LED auf dem Empfänger leuchtet und zeigt damit an, dass Sender und Empfänger gebunden sind.
5. Nehmen Sie den Bindestecker aus dem Bindeport herraus und heben ihn sorgfältig auf.
Sie müssen den Bindevorgang wiederholen wenn:
• SieandereFailsafepositionenwünschen,oderwenn die Gas- oder Lenkfunktion reversiert wurden.
• SieeinenanderenEmpfängerverwendenodervoneinem
DSM zu einem DSM2 oder Marine Empfänger wechseln.
• SiedenEmpfängeraneinenanderenSenderbinden.
Einige Spektrum Empfänger wie zum Beispiel der SR3001 haben einen Bindeknopf und keinen Bindeanschluß. (Port) Der Bindevorgang ist der gleiche. Statt vorher den Bindestecker einzustecken, drücken und halten Sie den Bindeknopf gedrückt während Sie den Empfänger einschalten um in den Bindemode zu gelangen.
FAILSAFE
Die Failsafepositionen werden während des Bindes eingestellt. In dem unvorhergesehenden Fall, dass die RF Verbindung unterbrochen wird, fährt der Empfänger die Servos in die vorprogrammierten Failsafepositionen. Sollte der Empfänger vor dem Sender eingeschaltet werden geht der Empfänger in den Failsafemode. Wird dann der Sender eingeschaltet haben, Sie wieder normale Kontrolle über das Modell. Für mehr Informationen über das Einstellen der Faisafepositionen sehen Sie bitte im Abschnitt-Binden des Empfänger nach.
BINDEN DES EMPFÄNGERS
Binden ist der Prozess der Programmierung des Empfänger mit dem eindeutigen Signal eines spezifischen Senders (GUID). Ist der Empfänger an den Sender gebunden, wird nur er auf die Signale des Senders reagieren. Die DX2E und der SR200 sind ab Werk gebunden. Sollten Sie diese neu binden wollen folgen Sie bitte dieses Schritten:
8 SPEKTRUM DX2E Bedienungsanleitung
SERVOREVERSE
Sollte die Lenkbewegung nach Rechts nicht zur Folge haben, dass sich die Reifen auch nach rechts bewegen, müssen Sie den Kanal reversieren (umdrehen). Um den Kanal zu reversieren schalten Sie den dazugehörigen Schalter auf die andere Position - N steht für Normal, R für Reversiert. Sie können einen kleinen Schraubendreher nutzen um die Schalter zu bewegen.
Loading...
+ 16 hidden pages