Sony STR-DN1060, STR-DN860 Reference Guide
Multi Channel
AV Receiver
Reference Guide GB
Guide de référence FR
Guía de referencia ES
STR-DN1060/STR-DN860
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
To reduce the risk of fire, do not cover
the ventilation opening of the appliance
with newspapers, tablecloths, curtains,
etc.
Do not expose the appliance to naked
flame sources (for example, lighted
candles).
To reduce the risk of fire or electric
shock, do not expose this appliance to
dripping or splashing, and do not place
objects filled with liquids, such as vases,
on the appliance.
Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet.
As the main plug is used to disconnect
the unit from the mains, connect the
unit to an easily accessible AC outlet.
Should you notice an abnormality in the
unit, disconnect the main plug from the
AC outlet immediately.
Do not expose batteries or appliances
with battery-installed to excessive heat,
such as sunshine and fire.
The unit is not disconnected from the
mains as long as it is connected to the
AC outlet, even if the unit itself has been
turned off.
Excessive sound pressure from
earphones and headphones can cause
hearing loss.
This symbol is intended to
alert the user to the
presence of the Hot
Surface that may be hot if
it is touched during the
normal operation.
FOR UNITED STATES CUSTOMERS.
NOT APPLICABLE IN CANADA,
INCLUDING IN THE PROVINCE OF
QUEBEC.
POUR LES CONSOMMATEURS A UX
ÉTATS-UNIS. NON APPLICABLE AU
CANADA, Y COMPRIS LA
PROVINCE DE QUÉBEC.
For the customers in the USA
Owner’s Record
The model and serial numbers are
located on the rear of the unit. Record
these numbers in the space provided
below. Refer to them whenever you call
upon your Sony dealer regarding this
product.
Model No.
Serial No.
This symbol is intended to
alert the user to the
presence of uninsulated
“dangerous voltage” within
the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to
alert the user to the
presence of important
operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near
water.
6) Clean only with dry cloth.
GB
2
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or othe r apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of
the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If
the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during
lightning storms or when unused for
long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required
when the apparatus has been
damaged in any way, such as powersupply cord or plug is damaged,
liquid has been spilled or objects
have fallen into the apparatus, the
apparatus has been exposed to rain
or moisture, does not operate
normally, or has been dropped.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
GB
3
Properly shielded and grounded cables
and connectors must be used for
connection to host computers and/or
peripherals in order to meet FCC
emission limits.
To reduce the risk of electric shock, the
speaker cord should be connected to
the apparatus and the speakers in
accordance with the following
instructions.
1) Disconnect the AC power cord from
the MAINS.
2) Strip 10 to 15 mm of the wire
insulation of the speaker cord.
3) Connect the speaker cord to the
apparatus and the speakers carefully
so as not to touch the core of
speaker cord by hand. Also
disconnect the AC power cord from
the MAINS before disconnecting the
speaker cord from the apparatus a nd
the speakers.
Multi Channel AV Receiver
(STR-DN1060/STR-DN860)
This equipment must not be co-located
or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment and meets
the FCC radio frequency (RF) Exposure
Guidelines.
This equipment has very low levels of RF
energy that it deemed to comply
without maximum permissive exposure
evaluation (MPE). But it is desirable that
it should be installed and operated
keeping the radiator at least 20cm or
more away from person’s body
(excluding extremities: hands, wrists,
feet and ankles).
Compliance with FCC requirement
15.407(c)
Data transmission is always initiated by
software, which is the passed down
through the MAC, through the digital
and analog baseband, and finally to the
RF chip. Several special packets are
initiated by the MAC. These are the only
ways the digital baseband portion will
turn on the RF transmitter, which it then
turns off at the end of the packet.
Therefore, the transmitter will be on
only while one of the aforementioned
packets is being transmitted. In other
words, this device automatically
discontinue transmission in case of
either absence of information to
transmit or operational failure.
Frequency Tolerance: ±20 ppm
For customers in Canada
Properly shielded and grounded cables
and connectors must be used for
connection to host computers and/or
peripherals.
Multi Channel AV Receiver
(STR-DN1060/STR-DN860)
This device complies with Industry
Canada licence-exempt RSS
standard(s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
This equipment complies with IC
radiation exposure limits set forth for an
uncontrolled environment and meets
RSS-102 of the IC radio frequency (RF)
Exposure rules.
This equipment has very low levels of RF
energy that it deemed to comply
without maximum permissive exposure
evaluation (MPE). But it is desirable that
it should be installed and operated
keeping the radiator at least 20cm or
more away from person’s body
(excluding extremities: hands, wrists,
feet and ankles).
GB
4
5.15 GHz – 5.25 GHz band is restricted to
indoor operations only.
High-power radars are allocated as
primary users (i.e. priority users) of the
bands 5,250 MHz – 5,350 MHz and
5,650 MHz – 5,850 MHz and that these
radars could cause interference and/or
damage to LE-LAN devices.
For customers in Australia and
New Zealand
This equipment should be installed and
operated with at least 20cm and more
between the radiator and person’s body
(excluding extremities: hands, wrists,
feet and ankles).
For customers in Australia
Disposal of Old
Electrical & Electronic
Equipment (Applicable
in the European Union
and other European
countries wit h separate
collection systems)
On copyrights
This receiver incorporates Dolby* Digital
and Pro Logic Surround and the DTS**
Digital Surround System.
* Manufactured under license from
Dolby Laboratories. Dolby, Pro Logic,
Surround EX, and the double-D
symbol are trademarks of Dolby
Laboratories.
** For DTS patents, see
http://patents.dts.com.
Manufactured under license from
DTS Licensing Limited. DTS, DTS-HD,
the Symbol, & DTS and the Symbol
together are registered trademarks,
and DTS-HD Master Audio is a
trademark of DTS, Inc. © DTS, Inc. All
Rights Reserved.
This receiver incorporates HighDefinition Multimedia Interface
(HDMI™) technology.
The terms HDMI and HDMI HighDefinition Multimedia Interface, and the
HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the
United States and other countries.
Apple, the Apple logo, AirPlay, iPad,
iPhone, iPod, iPod classic, iPod nano,
iPod touch, and Retina are trademarks
of Apple Inc., registered in the U.S. and
other countries.
iPad Air and iPad mini are trademarks of
Apple Inc.
App Store is a service mark of Apple Inc.
All other trademarks and registered
trademarks are of their respective
holders. In this manual, ™ and marks
are not specified.
“Made for iPod,” “Mad e for iPhone,” and
“Made for iPad” mean that an electronic
accessory has been designed to
connect specifically to iPod, iPhone, or
iPad, respectively, and has been
certified by the developer to meet Apple
performance standards.
Apple is not responsible for the
operation of this device or its
compliance with safety and regulatory
standards. Please note that the use of
this accessory with iPod, iPhone, or iPad
may affect wireless performance.
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.
This product is protected by certain
intellectual property rights of Microsoft
Corporation. Use or distribution of such
technology outside of this product is
prohibited without a license from
Microsoft or an authorized Microsoft
subsidiary.
GB
5
The LDAC™ name and logo is a
trademark of Sony Corporation.
“DSEE HX” is a trademark of Sony
Corporation.
MPEG Layer-3 audio coding technology
and patents licensed from Fraunhofer
IIS and Thomson.
“x.v.Color (x.v.Colour)” and “x.v.Color
(x.v.Colour)” logo are trademarks of
Sony Corporation.
“BRAVIA” is a trademark of Sony
Corporation.
“PlayStation” is a registered trademark
of Sony Computer Entertainment Inc.
“WALKMAN” and “WALKMAN” logo are
registered trademarks of Sony
Corporation.
MICROVAULT is a trademark of Sony
Corporation.
WPA™ and WPA2™ are trademarks of
Wi-Fi Alliance®.
The Wi-Fi CERTIFIED™ Logo is a
certification mark of Wi-Fi Alliance®.
MHL, Mobile High-Definition Link and
the MHL Logo are trademarks or
registered trademarks of MHL
Licensing, LLC.
The BLUETOOTH® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under
license. Other trademarks and trade
names are those of their respective
owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.
Android™ is a trademark of Google Inc.
Google Play™ is a trademark of Google
Inc.
Notice on End User License
Agreement (EULA)
For details of the EULA for this product,
see page 14.
For details of the EULA for network
services, please refer to [License
agreement] in options menu on each
network service icon.
For details of the GPL, LGPL and other
software licenses, please refer to
[Software License Information] in
[System Settings] of the [Setup] menu
on this product.
This product contains software that is
subject to the GNU General Public
License (“GPL”) or GNU Lesser General
Public License (“LGPL”). These establish
that customers have the right to
acquire, modify, and redistribute the
source code of said software in
accordance with the terms of the GPL or
the LGPL.
The source code for the software used
in this product is subject to the GPL and
LGPL, and is available on the Web.
To download, please access the
following:
URL:
http://oss.sony.net/Products/Linux
Please note that Sony cannot answer or
respond to any inquiries regarding the
content of this source code.
End User License Information
REAL END USER LICENSE
AGREEMENT (Taiwanese models
only)
1. End users are prohibited from
modifying, translating, reverse
engineering, decompiling,
disassembling or using other means
to discover the software d eveloped by
Real or otherwise replicate the
functionality of the software, except
to the extent that this restriction is
expressly prohibited by applicable
law.
GB
6
2.Real disclaims all warranties and
conditions, express and implied,
including implied warranties or
conditions of merchantability and
fitness for a particular purpose; and
effectively exclude all liability for
indirect, special, incidental and
consequential damages, including
but not limited to lost profits or
replacement systems.
Precautions
On safety
Should any solid object or liquid fall into
the cabinet, unplug the receiver and
have it checked by qualified personnel
before operating it any further.
On power sources
Before operating the receiver, check
that the operating voltage is identical
with your local power supply.
The operating voltage is indicated on
the nameplate on the back of the
receiver.
If you are not going to use the receiver
for a long time, be sure to disconnect
the receiver from the wall outlet. To
disconnect the AC power cord (mains
lead), grasp the plug itself; never pull
the cord.
(USA and Canadian models only)
One blade of the plug is wider than the
other for the purpose of safety and will
fit into the wall outlet only one way. If
you are unable to insert the plug fully
into the outlet, contact your dealer.
The AC power cord (mains lead) must
be changed only at a qualified service
shop.
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If
you continuously use this receiver at a
large volume, the cabinet temperature
of the top, side and bottom rises
consider ably. To avoid b urning yourself,
do not touch the cabinet.
On placement
Place the receiver in a location with
adequate ventilation to prevent heat
buildup and prolong the life of the
receiver.
Do not place the receiver near heat
sources, or in a place subject to direct
sunlight, excessive dust, or
mechanical shock.
Do not place anything on top of the
cabinet that might block the
ventilation holes and cause
malfunctions.
Do not place the receiver near
equipment such as a TV, VCR, or tape
deck. (If the receiver is being used in
combination with a TV, VCR, or tape
deck, and is placed too close to that
equipment, noise may result, and
picture quality may suffer. This is
especially likely when using an indoor
antenna (aerial).)
Use caution when placing the receiver
on surfaces that have been specially
treated (with wax, oil, polish, etc.) as
staining or discoloration of the surface
may result.
On operation
Before connecting other equipment, be
sure to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel, and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzine.
GB
7
On BLUETOOTH communication
BLUETOOTH devices should be used
within approximately 10 meters
(33 feet) (unobstructed distance) of
each other. The effective
communication range may become
shorter under the following
conditions.
When a person, meta l object, wall or
other obstruction is between the
devices with a BLUETOOTH
connection
Locations where a wireless LAN is
installed
Around microwave ovens that are in
use
Locations where other
electromagnetic waves occur
BLUETOOTH devices and wireless LAN
(IEEE 802.11b/g/n) use the same
frequency band (2.4 GHz). When using
your BLUETOOTH device near a device
with wireless LAN capability,
electromagnetic interference may
occur. This could result in lower data
transfer rates, noise, or inability to
connect. If this happens, try the
following remedies:
Use this receiver at least 10 meters
(33 feet) away from the wireless LAN
device.
Turn off the power to the wireless
LAN equipment when using your
BLUETOOTH device within 10 meters
(33 feet).
Install this receiver and BLUETOOTH
device as closer to each other as
possible.
The radio waves broadcast by this
receiver may interfere with the
operation of some medical devices.
Since this interference may result in
malfunction, always turn off the po wer
on this receiver and BLUETOOTH
device in the following locations:
In hospitals, on trains, in airplanes,
at gas stations, and any place where
flammable gasses may be present
Near automatic doors or fire alarms
This receiver supports security
functions that comply with the
BLUETOOTH specification to ensure
secure connection during
communication using BLUETOOTH
technology. However, this security
may be insufficient depending on the
setting contents and other factors, so
always be careful when performing
communication using BLUETOOTH
technology.
Sony cannot be held liable in any way
for damages or other loss resulting
from information leaks during
communication using BLUETOOTH
technology.
BLUETOOTH communication is not
necessarily guaranteed with all
BLUETOOTH devices that have the
same profile as this receiver.
BLUETOOTH devices connected with
this receiver must comply with the
BLUETOOTH specification prescribed
by the Bluetooth SI G, Inc., and must be
certified to comply. However, even
when a device complies with the
BLUETOOTH specification, there may
be cases where the characteristics or
specifications of the BLUETOOTH
device make it impossible to connect,
or may result in different control
methods, display or operation.
Noise may occur or the audio may cut
off depending on the BLUETOOTH
device connected with this receiver,
the communications environment, or
surrounding conditions.
If you have any questions or problems
concerning your rece iver, please consult
your nearest Sony dealer.
GB
8
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(USA models only)
STR-DN1060:
With 6 ohm loads, both channels driven,
from 20 Hz – 20,000 Hz; rated 100 watts
per channel minimum RMS power, with
no more than 0.09% total harmonic
distortion from 250 milliwatts to rated
output.
STR-DN860:
With 6 ohm loads, both channels driven,
from 20 Hz – 20,000 Hz; rated 95 watts
per channel minimum RMS power, with
no more than 0.09% total harmonic
distortion from 250 milliwatts to rated
output.
Amplifier section
STR-DN1060
USA, Canadian, Australian and Taiwanese
1)
models
:
Minimum RMS Output Power
(6 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(6 ohms, 1 kHz, THD 1%)
120 W + 120 W
Surround Mode Output Power
(6 ohms, 1 kHz, THD 0.9%)
165 W per channel
Singaporean models
1)
Minimum RMS Output Power
(6 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(6 ohms, 1 kHz, THD 1%)
120 W + 120 W
Surround Mode Output Power
(6 ohms, 1 kHz, THD 0.9%)
150 W per channel
2)
:
2)
STR-DN860
Minimum RMS Output Power
1)
(6 ohms, 20 Hz – 20 kHz, THD 0.09%)
95 W + 95 W
Stereo Mode Output Power
1)
(6 ohms, 1 kHz, THD 1%)
110 W + 110 W
Surround Mode Output Power
1)2)
(6 ohms, 1 kHz, THD 0.9%)
150 W per channel
1)
Measured under the following
conditions:
Area Power
USA, Canada, Taiwan 120 V AC, 60 Hz
Australia, Singapore 230 V AC, 50 Hz
2)
Reference power output for front, center,
requirements
surround, surround back and front high
speakers. Depending on the sound field
settings and the source, there may be no
sound output.
Frequency response
Analog
10 Hz – 100 kHz, +0.5/–2 dB (with
sound field and equalizer
bypassed)
Input
Analog
Sensitivity: 500 mV/50 kilohms
3)
: 105 dB (A, 500 mV4))
S/N
Digital (Coaxial)
Impedance: 75 ohms
S/N: 100 dB (A, 20 kHz LPF)
Digital (Optical)
S/N: 100 dB (A, 20 kHz LPF)
Output (Analog)
ZONE 2
5)
Voltage: 2 V/1 ki lohm
SUBWOOFER
Voltage: 2 V/1 ki lohm
Equalizer
Gain levels
±10 dB, 1 dB step
3)
INPUT SHORT (with sound field and
equalizer bypassed).
4)
Weighted network, input level.
5)
STR-DN1060 only.
GB
9
FM tuner section
Tuning range
USA and Canadian models:
87.5 MHz – 108.0 MHz (100 kHz step)
Other models:
87.5 MHz – 108.0 MHz (50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO*:
Y: 1 Vp-p, 75 ohms
P
B: 0.7 Vp-p, 75 ohms
R: 0.7 Vp-p, 75 ohms
P
80 MHz HD Standby Through
* STR-DN1060 only.
10
GB
HDMI Video
Input/Output (HDMI Repeater block)
STR-DN1060: HDMI IN SAT/CATV (MHL) and HDMI OUT A (TV) jacks support HDCP 2.2
protocol.
STR-DN860: HDMI IN SAT/CATV (MHL) and HDMI TV OUT jacks support HDCP 2.2 protocol.
HDCP 2.2 is newly enhanced copyright protection technology that is used to protect
content such as 4K movies.
3D
Format 2D
4096 × 2160p @ 59.94/60 Hz
4096 × 2160p @ 50 Hz
3840 × 2160p @ 59.94/60 Hz
3840 × 2160p @ 50 Hz
4096 × 2160p @ 23.98/24 Hz
3840 × 2160p @ 29.97/30 Hz
3840 × 2160p @ 25 Hz
3840 × 2160p @ 23.98/24 Hz
1920 × 1080p @ 59.94/60 Hz
1920 × 1080p @ 50 Hz
1920 × 1080p @ 29.97/30 Hz
1920 × 1080p @ 25 Hz
1920 × 1080p @ 23.98/24 Hz
1920 × 1080i @ 59.94/60 Hz
1920 × 1080i @ 50 Hz
1280 × 720p @ 59.94/60 Hz
1280 × 720p @ 50 Hz
1280 × 720p @ 29.97/30 Hz
1280 × 720p @ 23.98/24 Hz
720 × 480p @ 59.94/60 Hz
720 × 576p @ 50 Hz
640 × 480p @ 59.94/60 Hz
1)
Supports YUV 4:2:0 / 8 bit format only.
2)
Supports 8 bit format only.
3)
These formats are also supported by MHL 2 and MHL 3 connection.
4)
These formats are also supported by an MHL 3 connection.
2)4)
2)4)
2)4)
2)4)
Frame
packing
1)
1)
1)
1)
Side-by-Side
(Half)
Over-Under
(Top-and-Bottom)
4)
4)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
4)
4)
4)
4)
4)
3)
3)
3)
3)
3)
4)
4)
4)
4)
3)
3)
3)
3)
4)
4)
3)
3)
3)
3)
3)
3)
3)
3)
3)
GB
11
MHL section
Supported MHL version
Incorporates MHL 2 (front)*, MHL 3
(rear)
Maximum current
900 mA
* STR-DN1060 only.
iPhone/iPad/iPod section
DC 5V 1.0 A MAX
USB works with iPhone 6, iPhone 6 Plus,
iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s,
iPhone 4, iPhone 3GS, iPhone 3G, iPod
touch (2nd through 5th generation), iPod
classic, and iPod nano (3rd through 7th
generation).
BLUETOOTH technology works with iPhone
6, iPhone 6 Plus, iPhone 5s, iPhone 5c,
iPhone 5, iPhone 4s, iPhone 4, iPhone 3GS,
and iPod touch (4th and 5th generation).
AirPlay works with iPhone, iPad, and iPod
touch with iOS 4.3.3 or later, Mac with OS X
Mountain Lion or later, and PC with iTunes
10.2.2 or later.
You can use “SongPal” app with this
receiver via BLUETOOTH or network
connection.
You can only charge the iPhone/iPod when
they are connected to the USB port while
the receiver is turned on.
USB section
(USB) port:
Type A (For connecting USB memory)
NETWORK section
Ethernet LAN
100BASE-TX
Wireless LAN
Compatible standards:
IEEE 802.11 a/b/g/n
Security:
WPA/WPA2-PSK, WEP
Radio frequency:
2.4 GHz, 5 GHz
BLUETOOTH section
Communication system
BLUETOOTH Specification version 3.0
Output
BLUETOOTH Specification Power
Class 1
Maximum communication range
Line of sight a pprox. 30 m (98.4 feet)
Frequency band
2.4 GHz band (2.4000 GHz –
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread
Spectrum)
Compatible BLUETOOTH profiles
2)
A2DP 1.2 (Advanced Audio
Distribution Profile)
AVRCP 1.5 (Audio Video Remote
Control Profile)
SPP (Serial Port Profile)
Supported Codecs
3)
SBC4), AAC, LDAC
Transmission range (A2DP)
20 Hz – 20,000 Hz (Sampling
frequency 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic fields around a
microwave oven, static electricity,
cordless phone, reception sensitivity,
antenna’s performance, operating
system, software application, etc.
2)
BLUETOOTH standard profiles indicate
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4)
Subband Codec
General
Power requirements
Area Power requirements
USA, Canada,
Tai wa n
Australia 230 V AC, 50 Hz
Singapore 220 V – 240 V AC,
120 V AC, 60 Hz
50/60 Hz
1)
12
GB
Power consumption
240 W
Power consumption (during standby
mode)
STR-DN1060:
0.3 W (When [Control for HDMI],
[Standby Through], [Remote
Start], [Bluetooth Standby] and all
zone power are set to [Off].)
0.8 W (When [Control for HDMI] is
set to [On], and [Standby
Through], [Remote Start],
[Bluetooth Standby] and all zone
power are set to [Off].)
1.7 W (When [Control for HDMI]
and [Bluetooth Standby] are set to
[On], and [Standby Through],
[Remote Start] and all zone power
are set to [Off].)
STR-DN860:
0.3 W (When [Control for HDMI],
[Standby Through], [Remote Start]
and [Bluetooth Standby] are set to
[Off].)
0.5 W (When [Control for HDMI] is
set to [On], and [Standby
Through], [Remote Start] and
[Bluetooth Standby] are set to
[Off].)
1.7 W (When [Control for HDMI]
and [Bluetooth Standby] are set to
[On], and [Standby Through] and
[Remote Start] are set to [Off].)
Dimensions (width/height/depth)
(Approx.)
STR-DN1060:
430 mm × 172 mm × 329.4 mm
(17 in × 6 7/8 in × 13 in)
including projecting parts and
controls
STR-DN860:
430 mm × 156 mm × 329.4 mm
(17 in × 6 1/4 in × 13 in)
including projecting parts and
controls
Mass (Approx.)
STR-DN1060:
10.4 kg (22 lb 15 oz)
STR-DN860:
8.3 kg (18 lb 5 oz)
Design and specifications are subject to
change without notice.
13
GB
END USER LICENSE AGREEMENT
IMPORTANT:
BEFORE USING THE SOFTWARE, PLEASE READ THIS END USER LICENSE AGREEMENT
(“EULA”) CAREFULLY. BY USING THE SOFTWARE YOU ARE ACCEPTING THE TERMS OF THIS
EULA. IF YOU DO NOT ACCEPT THE TERMS OF THIS EULA, YOU MAY NOT USE THE
SOFTWARE.
This EULA is a legal agreement between you and Sony Corporation (“SONY”). This EULA
governs your rights and obligations regarding the SONY software of SONY and/or its third
party licensors (including SONY’s affiliates) and their respective affiliates (collectively, the
“THIRD-PARTY SUPPLIERS”), together with any updates/upgrades provided by SONY, any
printed, on-line or other electronic documentation for such software, and any data files
created by operation of such software (collectively, the “SOFTWARE”).
Notwithstanding the foregoing, any software in the SOFTWARE having a separate end
user license agreement (including, but not limited to, GNU General Public license and
Lesser/Library General Public License) shall be covered by such applicable separate end
user license agreement in lieu of the terms of this EULA to the extent required by such
separate end user license agreement (“EXCLUDED SOFTWARE”).
SOFTWARE LICENSE
The SOFTWARE is licensed, not sold. The SOFTWARE is protected by copyright and other
intellectual property laws and international treaties.
COPYRIGHT
All right and title in and to the SOFTWARE (including, but not limited to, any images,
photographs, animation, video, audio, music, text and “applets” incorporated into the
SOFTWARE) is owned by SONY or one or more of the THIRD-PARTY SUPPLIERS.
GRANT OF LICENSE
SONY grants you a limited license to use the SOFTWARE solely in connection with your
compatible device (“DEVICE”) and only for your individual, non-commercial use. SONY and
the THIRD-PARTY SUPPLIERS expressly reserve all rights, title and interest (including, but
not limited to, all intellectual property rights) in and to the SOFTWARE that this EULA does
not specifically grant to you.
REQUIREMENTS AND LIMITATIONS
You may not copy, publish, adapt, redistribute, attempt to derive source code, modify,
reverse engineer, decompile, or disassemble any of the SOFTWARE, whether in whole or
in part, or create any derivative works from or of the SOFTWARE unless such derivative
works are intentionally facilitated by the SOFTWARE. You may not modify or tamper with
any digital rights management functionality of the SOFTWARE. You may not bypass,
modify, defeat or circumvent any of the functions or protections of the SOFTWARE or any
mechanisms operatively linked to the SOFTWARE. You may not separate any individual
component of the SOFTWARE for use on more than one DEVICE unless expressly
authorized to do so by SONY. You may not remove, alter, cover or deface any trademarks
or notices on the SOFTWARE. You may not share, distribute, rent, lease, sublicense,
assign, transfer or sell the SOFTWARE. The software, network services or other products
other than SOFTWARE upon which the SOFTWARE’S performance depends might be
interrupted or discontinued at the discretion of the suppliers (software suppliers, service
suppliers, or SONY). SONY and such suppliers do not warrant that the SOFTWARE, network
services, contents or other products will continue to be available, or will operate without
interruption or modification.
14
GB
USE OF SOFTWARE WITH COPYRIGHTED MATERIALS
The SOFTWARE may be capable of being used by you to view, store, process and/or use
content created by you and/or third parties. Such content may be protected by copyright,
other intellectual property laws, and/or agreements. You agree to use the SOFTWARE
only in compliance with all such laws and agreements that apply to such content. You
acknowledge and agree that SONY may take appropriate measures to protect the
copyright of content stored, processed or used by the SOFTWARE. Such measures include,
but are not limited to, counting the frequency of your backup and restoration through
certain SOFTWARE features, refusal to accept your request to enable restoration of data,
and termination of this EULA in the event of your illegitimate use of the SOFTWARE.
CONTENT SERVICE
PLEASE ALSO NOTE THAT THE SOFTWARE MAY BE DESIGNED TO BE USED WITH CONTENT
AVAILABLE THROUGH ONE OR MORE CONTENT SERVICES (“CONTENT SERVICE”). USE OF
THE SERVICE AND THAT CONTENT IS SUBJECT TO THE TERMS OF SERVICE OF THAT
CONTENT SERVICE. IF YOU DECLINE TO ACCEPT THOSE TERMS, YOUR USE OF THE
SOFTWARE WILL BE LIMITED. You acknowledge and agree that certain content and
services available through the SOFTWARE may be provided by third parties over which
SONY has no control. USE OF THE CONTENT SERVICE REQUIRES AN INTERNET
CONNECTION. THE CONTENT SERVICE MAY BE DISCONTINUED AT ANY TIME.
INTERNET CONNECTIVITY AND THIRD PARTY SERVICES
You acknowledge and agree that access to certain SOFTWARE features may require an
Internet connection for which you are solely responsible. Further, you are solely
responsible for payment of any third party fees associated with your Internet connection,
including but not limited to Internet service provider or airtime charges. Operation of the
SOFTWARE may be limited or restricted depending on the capabilities, bandwidth or
technical limitations of your Internet connection and service. The provision, quality and
security of such Internet connectivity are the sole responsibility of the third party
providing such service.
EXPORT AND OTHER REGULATIONS
You agree to comply with all applicable export and re-export restrictions and regulations
of the area or country in which you reside, and not to transfer, or authorize the transfer, of
the SOFTWARE to a prohibited country or otherwise in violation of any such restrictions or
regulations.
HIGH RISK ACTIVITIES
The SOFTWARE is not fault-tolerant and is not designed, manufactured or intended for
use or resale as on-line control equipment in hazardous environments requiring fail-safe
performance, such as in the operation of nuclear facilities, aircraft navigation or
communication systems, air traffic control, direct life support machines, or weapons
systems, in which the failure of the SOFTWARE could lead to death, personal injury, or
severe physical or environmental damage (“HIGH RISK ACTIVITIES”). SONY, each of the
THIRD-PARTY SUPPLIERS, and each of their respective affiliates specifically disclaim any
express or implied warranty, duty or condition of fitness for HIGH RISK ACTIVITIES.
EXCLUSION OF WARRANTY ON SOFTWARE
You acknowledge and agree that use of the SOFTWARE is at your sole risk and that you
are responsible for use of the SOFTWARE. The SOFTWARE is provided “AS IS,” without
warranty, duty or condition of any kind.
15
GB
SONY AND EACH OF THE THIRD-PARTY SUPPLIERS (for purposes of this Section, SONY and
each of the THIRD-PARTY SUPPLIERS shall be collectively referred to as “SONY”)
EXPRESSLY DISCLAIM ALL WARRANTIES, DUTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY,
NONINFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE. SONY DOES NOT
WARRANT OR MAKE ANY CONDITIONS OR REPRESENTATIONS (A) THAT THE FUNCTIONS
CONTAINED IN ANY OF THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT THEY
WILL BE UPDATED, (B) THAT THE OPERATION OF ANY OF THE SOFTWARE WILL BE CORRECT
OR ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, (C) THAT THE SOFTWARE
WILL NOT DAMAGE ANY OTHER SOFTWARE, HARDWARE OR DATA, (D) THAT ANY
SOFTWARE, NETWORK SERVICES (INCLUDING THE INTERNET) OR PRODUCTS (OTHER THAN
THE SOFTWARE) UPON WHICH THE SOFTWARE’S PERFORMANCE DEPENDS WILL CONTINUE
TO BE AVAILABLE, UNINTERRUPTED OR UNMODIFIED, AND (E) REGARDING THE USE OR
THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY,
RELIABILITY, OR OTHERWISE.
NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY SONY OR AN AUTHORIZED
REPRESENTATIVE OF SONY SHALL CREATE A WARRANTY, DUTY OR CONDITION OR IN ANY
WAY INCREASE THE SCOPE OF THIS WARRANTY. SHOULD THE SOFTWARE PROVE
DEFECTIVE YOU ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES, SO THESE EXCLUSIONS MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
SONY AND EACH OF THE THIRD-PARTY SUPPLIERS (for purposes of this Section, SONY and
each of the THIRD-PARTY SUPPLIERS shall be collectively referred to as “SONY”) SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY
OR UNDER ANY OTHER LEGAL THEORY RELATED TO THE SOFTWARE, INCLUDING, BUT NOT
LIMITED TO, ANY DAMAGES ARISING OUT OF LOSS OF PROFITS, LOSS OF REVENUE, LOSS
OF DATA, LOSS OF USE OF THE SOFTWARE OR ANY ASSOCIATED HARDWARE, DOWN TIME
AND USER’S TIME, EVEN IF ANY OF THEM HAVE BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN ANY CASE, EACH AND ALL OF THEIR AGGREGATE LIABILITY UNDER
ANY PROVISION OF THIS EULA SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID FOR
THE PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION
MAY NOT APPLY TO YOU.
AUTOMATIC UPDATE FEATURE
From time to time, SONY or the THIRD-PARTY SUPPLIERS may automatically update or
otherwise modify the SOFTWARE, including, but not limited to, for purposes of
enhancement of security functions, error correction and improvement of functions, at
such time as you interact with SONY’s or third parties’ servers, or otherwise. Such updates
or modifications may delete or change the nature of features or other aspects of the
SOFTWARE, including, but not limited to, functions you may rely upon. You acknowledge
and agree that such activities may occur at SONY’s sole discretion and that SONY may
condition continued use of the SOFTWARE upon your complete installation or acceptance
of such update or modifications. Any updates/modifications shall be deemed to be, and
shall constitute part of, the SOFTWARE for purposes of this EULA. By acceptance of this
EULA, you consent to such update/modification.
16
GB
Loading...