SONY DCR-TRV12 Service Manual
DCR-TRV12E/TRV14E/TRV19/TRV19E
COVER
COVER
SECTION 2
DISASSEMBLY
The following flow chart shows the disassembly procedure.
DISASSEMBLY
DISASSEMBLY
SERVICE POSITION TO
CHECK THE VTR SECTION
PD-188 board
service position
DISASSEMBLY
HELP
HELP
HELP
DISASSEMBLY
DISASSEMBLY
HELP
PROCEDURE OF REMOVING MECHANISM DECK
1 2-2. CABINET (R) COVER (39E) ASSEMBLY ........
2 2-3. F PANEL SECTION ........................................
3 2-5. CABINET (R) SECTION ...................................
4 2-10. BT PANEL/EVF SECTION ...........................
5 2-14. VA-118 BOARD, LENS SECTION ................
6 2-16. MECHANISM DECK, VC-311 BOARD (1) ....
7 2-17. MECHANISM DECK, VC-311 BOARD (2) ....
(page 2-4)
(page 2-5)
(page 2-7)
(page 2-11)
(page 2-15)
(page 2-16)
(page 2-17)
DISASSEMBLY
HELP
DISASSEMBLY
HELP
DISASSEMBLY
DISASSEMBLY
HELP
2-1
2-1. P CABINET (C) ASSEMBLY
Caution
Rotation of the LCD panel has limitation due to its
hinge in this model. Excessive force to rotate the
LCD panel damages the hinge. Follow the precaution
below.
Opening and closing of LCD panel must be performed
only in the state that the LCD panel is completely in
parallel (perpendicular) with the main body of the
recorder.
3
Screw
(M1.7 × 4),
lock ace, p2
DCR-TRV12E/TRV14E/TRV19/TRV19E
4
2
Turn the LCD panel
1
Open the
LCD panel
7
Four claws
5
Screw
(M1.7
lock ace, p2
8
P cabinet (C) assembly
LCD panel
×
4),
Turn the
When you want to rotate the LCD panel, rotate it after
the LCD panel is opened in its fully opened position.
[PD-188 BOARD SERVICE POSITION]
PD-188 board
PD-188
6
Two tapping screws
×
(M1.7
5)
Adjustment remote
commander (RM-95)
PD-188
2-3
AC power
adaptor
CPC-7 jig
(J-6082-382-A)
AC IN
DCR-TRV12E/TRV14E/TRV19/TRV19E
2-2. CABINET (R) COVER (39E) ASSEMBLY
1
Two screws
(M1.7 × 6),
lock ace, p2
Caution
5
Raise the Finder in the
direction of the arrow
6
Screw
×
(M1.7
lock ace, p2
4
Two screws
(M1.7 × 3),
lock ace, p2
3
Open the LCD panel
3),
When remove the Cabinet R cover
(39E) to the main body, remove the
Cabinet R cover (39E) while raising,
A
so that
be damaged.
marked portion must not
A
2
Screw
(M1.7 × 3),
lock ace, p2
Caution
Insert the projected portion of the Cabinet R cover (40E)
assembly into the cabinet L side of the the chassis.
The projected
portion
The chassis
The cabinet L side
9
Remove the
projected part
8
Remove the
projected part
q;
Push the Cabinet R cover (39E)
in the direction of the arrow to
remove the three claws.
Claws
7
Close the LCD panel
2-4
qa
Pull out the Cabinet R cover (39E)
from the main body.
2-3. F PANEL SECTION
3
Open the Cassette lid
4
Screw
(M1.7 × 4),
lock ace, p2
DCR-TRV12E/TRV14E/TRV19/TRV19E
1
Screw
(M1.7
lock ace, p2
×
4),
7
Remove the F panel section
in the direction of the arrow
6
Remove the claw
2
Screw
×
(M1.7
lock ace, p2
4),
5
Two screws
×
(M1.7
lock ace, p2
4),
8
FP-621 flexible board
(36P)
2-5
Caution
The FP-621 flexible board may be damaged
if you remove the F panel section forcibly.
Be very careful not to damage the flexible
board.
2-5. CABINET (R) SECTION
4
Three screws
×
(M1.7
lock ace, p2
4),
2
Screw
×
(M1.7
lock ace, p2
4),
DCR-TRV12E/TRV14E/TRV19/TRV19E
1
Screw
(M1.7 × 4),
lock ace, p2
3
Two screws
(M1.7 × 4),
lock ace, p2
Caution
When install the Cabinet R section to the
main body, install the FP-618 flexible board
as shown in the illustration.
6
FP-618 flexible board (16P)
7
Herness (PV-140)
(20P)
5
Remove the Cabinet R section
in the direction of the arrow
2-7
Loading...