Sony CCD-TRV128, CCD-TRV228, CCD-TRV328, CCD-TRV428 ADJUSTMENTS
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
RMT-833
Ver 1.0 2003. 11
Revision History
Revision History
Link
Link
Before starting adjustments
Before starting adjustments
Adjusting items when replacing main parts and boards
Adjusting items when replacing main parts and boards
CAMERA SECTION ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE DATA
INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE DATA
CAMERA SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
MECHANISM SECTION ADJUSTMENTS
MECHANISM SECTION ADJUSTMENTS
SECTION 6
ADJUSTMENTS
ADJ
ADJUSTMENT REMOTE COMMANDER
ADJUSTMENT REMOTE COMMANDER
OPERATING WITHOUT CASSETTE
OPERATING WITHOUT CASSETTE
TAPE PATH ADJUSTMENT
TAPE PATH ADJUSTMENT
9-876-290-51
Sony EMCS Co.
2003K0500-1
©2003.11
Published by DI CS Strategy Div
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
TABLE OF CONTENTS
Section Title Page Section Title Page
6. ADJUSTMENTS
1. Before Starting Adjustments ···········································6-1
1-1. Adjusting Items when Replacing
Main Parts and Boards ···················································· 6-2
6-1. Camera Section Adjustments··········································· 6-4
1-1. Preparations before Adjustments (CAMERA Section)···6-4
1-1-1.List of Service Tools························································6-4
1-1-2.Preparations ·····································································6-5
1-1-3.Precaution········································································6-6
1. Setting the Switch····························································6-6
2. Order of Adjustments ······················································6-6
3. Subjects ··········································································· 6-6
1-2. Initialization of 8, A, C, D, E, F, 1F Page Data ···············6-7
1. Initializing the 8, A, C, D, E, F, 1F Page Data ················6-7
2. Modification of 8, A, C, D, E, F, 1F Page Data···············6-7
3. 8 Page Table·····································································6-7
4. A Page Table····································································6-8
5. C Page Table ····································································6-9
6. D Page Table····································································6-9
7. E Page Table ··································································6-10
8. F Page Table ··································································6-11
9. 1F Page Table ································································6-11
1-3. Camera System Adjustments·········································6-12
1. Hall Adjustment·····························································6-12
2. Flange Back Adjustment
(Using the Minipattern Box) ·········································6-13
3. Flange Back Adjustment
(Using the Flange Back Adjustment Chart
and Subject More than 500 m Away) ····························6-14
4. Flange Back Check························································6-15
5. Optical Axis Adjustment ···············································6-16
6. Picture Frame Setting ····················································6-17
7. Color Reproduction Adjustment····································6-18
8. LV Standard Data Input ·················································6-19
9. Auto White Balance Standard Data Input ·····················6-19
10. Auto White Balance Adjustment ···································6-20
11. Auto White Balance Check ···········································6-21
12. Angular Velocity Sensor Output Check and Steadyshot
Check (CCD-TRV328/TRV428/TRV428E) ·················· 6-22
13. CCD Defect Check ························································6-22
1-4. LCD System Adjustments ·············································6-23
1. LCD Level Adjustment (PD-204 Board) ······················· 6-23
2. LCD V-COM Adjustment (PD-204 Board) ···················6-24
3. LCD White Balance Adjustment (PD-204 Board) ········6-24
6-2. Mechanism Section Adjustments ··································6-25
2-1. Adjustment Remote Commander ··································6-25
2-2. Operating Without Cassette···········································6-25
2-3. Tape Path Adjustment····················································6-25
6-3. Video Section Adjustments ··········································· 6-26
3-1. Preparations before Adjustments···································6-26
3-1-1.Equipment to Required··················································6-26
3-1-2.Precautions on Adjusting ···············································6-27
3-1-3.Adjusting Connectors ····················································6-27
3-1-4.Connecting the Equipment ············································6-27
3-1-5.Alignment Tapes····························································6-28
3-1-6.Output Level and Impedance········································· 6-29
3-1-7.Recording Mode (Standard 8/Hi8) Switching···············6-29
3-2. System Control System Adjustments ····························6-30
1. Initialization of 8, A, C, D, E, F, 1F Page Data ·············6-30
3-3. Servo System Adjustments ············································6-30
1. CAP FG Offset Adjustment (VC-341 Board) ···············6-30
2. Switching Position Adjustment (VC-341 Board)··········6-30
3-4. Video System Adjustments············································6-31
1. 28 MHz Origin Oscillation Adjustment
(VC-341 Board)·····························································6-31
2. AFC f0 Adjustment (VC-341 Board)·····························6-31
3. S VIDEO OUT Y Level Adjustment
(VC-341 Board)·····························································6-32
4. S VIDEO OUT C Level Adjustment
(VC-341 Board)·····························································6-32
5. VIDEO OUT Level Check (VC-341 Board)·················6-33
6. REC Y Current Adjustment (VC-341 Board)················6-34
7. REC C/AFM Current Adjustment ·································6-35
7-1. Preparations ···································································6-35
7-2. REC C Current Check (VC-341 Board)························6-35
7-3. REC AFM Current Adjustment (VC-341 Board) ·········· 6-36
7-4. Processing after Completed Adjustment ······················· 6-36
3-5. Audio System Adjustments ···········································6-37
1. BPF f0 Adjustment (VC-341 Board)······························6-37
2. 1.5 MHz Deviation Adjustment (VC-341 Board) ········· 6-37
6-4. Service Mode·································································6-38
4-1. Adjustment Remote Commander ··································6-38
1. Using the Adjustment Remote Commander··················6-38
2. Precautions Upon Using the Adjustment
Remote Commander······················································6-38
4-2. Data Process ··································································6-39
4-3. Service Mode·································································6-40
1. Setting the Test Mode ····················································6-40
2. Emergency Memory Address ········································6-41
2-1. EMG Code (Emergency Code) ·····································6-41
2-2. MSW Codes ·································································· 6-42
3. Bit V alue Discrimination ···············································6-43
4. Switch Check (1) ···························································6-43
5. Switch Check (2) ···························································6-43
6. Switch Check (3) ···························································6-44
7. LED, Video Light, IR Light Check ·······························6-44
8. Record of Use Check·····················································6-45
9. Record of Self-diagnosis Check ····································6-46
* The camera optical axis frame is shown on page 6-47.
The camera color reproduction frame is shown on page
6-48.
— 2 —
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
(Machine before starting repair)
(Machine after a board is replaced)
PC PC
Save the EVR data
to a personal computer.
Download the saved
data to a machine.
1. Before starting adjustments
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
SECTION 6
ADJUSTMENTS
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed
EEPROM to the replaced board.
Remove the EEPROM and install it.
(Former board)
(New board)
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
(Machine to be repaired) (Machine to be repaired)
PC
Download the data.
After the EVR data is saved and downloaded, chec k the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)
Save the data.
(The same model of the same destination)
6-1
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-1. Adjusting items when replacing main parts and boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Block replacement Mounted part replacement
Replaced part
Adjustment Section Adjustment
Initialization of 8, A, C, D,
E, F, 1F page data
Initializing of 8, A, C, D, E, F, 1F page
data
(LCD panel)
(Fluorescent tube)
Lens device
Video light (Note 2)
LCD block LCD901
LCD block ND901
Mechanism deck (Note 1)
(Drum assembly) (Note 1)
(Capstan motor)
(CCD imager)
(YAW, PITCH sensor) (Note 3)
(Timing generator)
(S/H, AGC, A/D CONV.)
(Camera/VTR process, Lens control)
Mechanism deck M901
Mechanism deck M902
CD-465 board IC951
SI-039 board SE751/752
VC-341 board IC151, X151
VC-341 board IC152
VC-341 board IC301
(REC/PB AMP)
(EVR)
(Audio/Video process)
(LCD driver)
VC-341 board IC481
VC-341 board IC251
VC-341 board IC801
PD-204 board IC6001
Camera HALL adj. z
Flange back adj. zz
Optical axis adj. zz
Color reproduction adj. zz
LV standard data input zz
AWB standard data input zz
Auto white balance adj. zz
Angular velocity sensor output check
and steadyshot check (Note 3)
z
LCD LCD level adj. z
LCD V-COM adj. zz
LCD White balance adj.
zz z
Servo CAP FG offset adj. zz
Switching position adj.
zz
Video 28 MHz origin osillation adj. zz
0
adj. z
AFC f
S VIDEO OUT Y level adj. zz
S VIDEO OUT C level adj. zz
REC Y current adj. zz
REC C/AFM current adj.
0
Audio BPF f
adj. z
1.5 MHz deviation adj.
Mechanism Tape path adj.
zzz
zz
z
Table 6-1-1 (1)
Note 1: When replacing the drum assy or mechanism deck, reset the data of page: 7, address: A4 to A6.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
Note 2: When replacing the video light, reset the data of page: 7, address: CE and CF.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
Note 3: CCD-TRV328/TRV428/TRV428E only
6-2
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Replaced part
Adjustment Section Adjustment
(COMPLETE)
(COMPLETE)
(EEPROM)
RadarWRadarWRadarW
PD-204 board
VC-341 board
VC-341 board IC602
Supporting
Initialization of 8, A, C, D,
E, F, 1F page data
Camera HALL adj. zzz
LCD LCD level adj. zzzz
Servo CAP FG offset adj. zzz
Video 28 MHz origin osillation adj. zz
Audio BPF f
Mechanism Tape path adj.
Initializing of 8, A, C, D, E, F, 1F page
data
zz
Flange back adj. zzz
Optical axis adj. zz
Color reproduction adj. zz
LV standard data input zzz
AWB standard data input zz
Auto white balance adj. zzz
Angular velocity sensor output check
and steadyshot check (Note 3)
zzz
LCD V-COM adj. zzz
LCD White balance adj.
Switching position adj.
0
adj. zzz
AFC f
zzz
zz
S VIDEO OUT Y level adj. zz
S VIDEO OUT C level adj. zz
REC Y current adj. zz
REC C/AFM current adj.
0
adj. zz
1.5 MHz deviation adj.
zz
zz
Table 6-1-1 (2)
6-3
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION)
1-1-1. List of Service Tools
• Oscilloscope • Color monitor • Vectorscope
• Regulated power supply • Digital voltmeter • Frequency counter
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander (RM-95 upgraded).
(Note)
Siemens star chart
Clear chart for pattern box
CPC jig connector
I/F unit for LANC control
Mini pattern box
Camera table
Name
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-539-A
J-6082-521-A
J-6082-353-B
J-6082-384-A
Auto white balance adjustment/check
White balance adjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For connecting the adjustment remote commander
For connecting the adjustment remote commander
For adjusting the flange back
For adjusting the flange back
Usage
J-1 J-2
J-6
J-11
J-7 J-8
J-3
J-4 J-5
J-9 J-10
Fig. 6-1-1
6-4
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-1-2. Preparations
Note: Before perform the adjustment, check that the data of page:
0, address: 10 is “00”.
If not, select page: 0, address: 10, and set data “00”.
1) Connect the equipment for adjustments according to Fig. 6-1-
3.
2) Connect the adjustment remote commander to VC-341 board
CN007 via I/F unit for LANC control (J-6082-521-A) and CPC
jig connector (J-6082-539-A). (Fig. 6-1-3)
To operate the adjustment remote commander, connect the AC
power adaptor to the DC IN jack of I/F unit for LANC control,
or connect the L series Info-LITHIUM battery to the battery
terminal of I/F unit for LANC control.
CN007
1
Pattern box
1 m
Front of the lens
Fig. 6-1-2
Screw (M2)
L serices Info
LITHIUM battery (7.2Vdc)
LANC jack
Adjustment
remote commander (RM-95)
CPC lid
AC adaptor
16
Video (yellow)
AC IN
Conductor side
CPC jig connector
(J-6082-539-A)
A/V OUT jack
TV monitor
Audio (black)
Vector scope
AC adaptor
Terminated at 75Ω
AC IN
I/F unit for LANC control
(J-6082-521-A)
Fig. 6-1-3
6-5
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (SS-5100 block) ..........................CAMERA
2. FOCUS (CF-5100 block) ..................................... MANUAL
3. BACK LIGHT (CF-5100 block) .................................... OFF
4. PROGRAM AE (MENU setting) ................................ AUTO
5. NIGHTSHOT PLUS switch (Lens block) ..................... OFF
6. EXPOSURE (CF-5100 block) .................................... AUTO
2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame)
H
Yellow
Cyan
Green
AB B
Fig. a
(VIDEO terminal of A/V jack
output waveform)
A=B
White
Magenta
Red
CD
Blue
A
Enlargement
C=D
Difference in level
7. P EFFECT (MENU setting) ........................................... OFF
8. D ZOOM (MENU setting) ............................................. OFF
9. DEMO MODE (MENU setting) .................................... OFF
10. 16 : 9 WIDE (MENU setting) ........................................ OFF
11. DISPLAY (MENU setting) ............................................ LCD
Electronic beam scanning frame
Red
Cyan
White
Green
Yellow
V
Fig. b (monitor TV picture)
Blue
Magenta
CRT picture frame
B
A
Fig. 6-1-4
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm × 841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
Adjust the camera zoom and direction to
obtain the output wavef orm shown in Fig. a and
the monitor TV display shown in Fig. b.
White
841 mm
Black
1189 mm
Fig. 6-1-5
6-6
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-2. INITIALIZATION OF 8, A, C, D, E, F, 1F
PAGE DATA
Note: If reading/writing data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
1. Initializing the 8, A, C, D, E, F, 1F Page Data
Note 1: If “Initialization of Pages 8, A, C, D, E, F, 1F” is ex-
ecuted, all data on pages 8, A, C, D, E, F, 1F are initialized. (Only an individual page cannot be initialized)
Note 2: If the 8, A, C, D, E, F, 1F page data has been initialized,
“Modification of 8, A, C, D, E, F, 1F Page Data” and all
adjustments need to be performed again.
Note 3: Check that the data of page: 0, address: 10 is “00”.
Note 4: NTSC model: CCD-TRV128/TRV228/TRV328/TRV428
PAL model: CCD-TRV228E/TRV428E
Adjusting Page 8
Adjusting Address 00 to FF
Adjusting Page A
Adjusting Address 10 to FF
Adjusting Page C
Adjusting Address 10 to FF
Adjusting Page D
Adjusting Address 10 to 7F
Adjusting Page E
Adjusting Address 00 to FF
Adjusting Page F
Adjusting Address 10 to FF
Adjusting Page 1F
Adjusting Address 00 to FF
Initializing method:
Order Page Address Data Procedure
10 0101
Set the following data.
27 03
37 00
47 01
57 02
62 0029
72 01 29 Press PAUSE button.
8
00: NTSC model
80: PAL model
Set the following data.
2D: NTSC model
2F: PAL model
Set the following data, and
press PAUSE button.
2D: NTSC model
2F: PAL model
Check the data changes to
“01”.
Perform “Modification of 8,
A, C, D, E, F, 1F Page Data”
2. Modification of 8, A, C, D, E, F, 1F Page Data
If the 8, A, C, D, E, F, 1F page data has been initialized, change
the data of the “Fixed data-2” address shown in the following table
by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
3) When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of 8, A, C, D, E, F, 1F
Page data
Order Page Address Data Procedure
12 0029
22 01 29 Press PAUSE button.
Note: If the following symptoms occur after completing of the
“Modification of 8, A, C, D, E, F, 1F page data”, check
that the data of the “Fixed data-2” addresses of 8, A, C, D,
E, F, 1F page are same as those of the same model of the
same destination.
1) The power is shut off so that unit cannot operate.
3. 8 Page table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
00 to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Remark
6-7
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4. A Page table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
10 to 20 Fixed data-1 (Initialized data)
22 to 2B Fixed data-1 (Initialized data)
2C Fixed data-2
2D to 30 Fixed data-1 (Initialized data)
32 to 40 Fixed data-1 (Initialized data)
42 to 44 Fixed data-1 (Initialized data)
46 to 4B Fixed data-1 (Initialized data)
4C Fixed data-2
4D Fixed data-1 (Initialized data)
4E
50, 51 Fixed data-1 (Initialized data)
54 to 64 Fixed data-1 (Initialized data)
66 to 7F Fixed data-1 (Initialized data)
82 to 8F Fixed data-1 (Initialized data)
91 to 95 Fixed data-1 (Initialized data)
99 to 9C Fixed data-1 (Initialized data)
9D
9E
A0
A1 to DF Fixed data-1 (Initialized data)
E0
E1
E2
E3
E4 Fixed data-2
E5
E6
E7
E8
Initial value
NTSC PAL
21 Fixed data-2
31 Fixed data-2
41 Fixed data-2
45 Fixed data-2
4F
52
53
65 Fixed data-2
80
81
90 Fixed data-2
96
97
98
9F
Fixed data-2
Fixed data-2
Fixed data-2
Fixed data-2
Fixed data-2
Remark
Address
E9
EA
EB
EC
ED
EE
EF
FA
FB
FC
FD
FE, FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
F0
F1
F2
F3 Fixed data-2
F4
F5
F6
F7
F8
F9
Remark
6-8
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
5. C Page table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
10 to 13 Fixed data-1 (Initialized data)
14 00 00 Test mode
15 Fixed data-1 (Initialized data)
16 0B 0A
17 00 00
18 83 83 CAP FG offset adj.
19 30 30 AFC f0 adj.
1A 68 62 S VIDEO OUT Y level adj.
1B 62 62 S VIDEO OUT C level adj.
1C, 1D Fixed data-1 (Initialized data)
1E B4 D7
1F B4 D7
20 to 24 Fixed data-1 (Initialized data)
25 A0 A0 REC C/AFM current adj.
26 to 2E Fixed data-1 (Initialized data)
2F A6 A6 1.5 MHz deviation adj.
30 80 80 BPF f0 adj.
31 to 4F Fixed data-1 (Initialized data)
50 67 79
51 79 67
52 84 84 LCD V -COM adj.
53 to 55 Fixed data-1 (Initialized data)
56 87 87
57 68 68
58 AF AF LCD level adj. (Contrast adj.)
59 to 5B Fixed data-1 (Initialized data)
5C
5D
5E to C0 Fixed data-1 (Initialized data)
C1 Fixed data-2
C2 to F3 Fixed data-1 (Initialized data)
F4 00 00
F5 00 00
F6 00 00
F7 00 00
F8 00 00
F9 00 00
FA 00 00
FB 00 00
FC 00 00
FD 00 00
FE 00 00
FF 00 00
Initial value
NTSC PAL
Remark
Switching position adj.
REC Y current adj.
LCD level adj. (VCO adj.)
LCD White balance adj.
Fixed data-2
Emergency memory
6. D Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
10 00 00 Test mode
11 Fixed data-1 (Initialized data)
12
13
14 to 21 Fixed data-1 (Initialized data)
22
23
24 Fixed data-2
25
26
27 to 29 Fixed data-1 (Initialized data)
2A
2B
2C to 35 Fixed data-1 (Initialized data)
36
37 Fixed data-2
38
39 Fixed data-1 (Initialized data)
3A Fixed data-2
3B to 55 Fixed data-1 (Initialized data)
56 Fixed data-2
57 Fixed data-1 (Initialized data)
58
59
5A to 6E Fixed data-1 (Initialized data)
6F Fixed data-2
70 to 7F Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Remark
Fixed data-2
Fixed data-2
Fixed data-2
6-9
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
7. E Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
00 to 0F Fixed data-1 (Initialized data)
11 to B0 Fixed data-1 (Initialized data)
B1 Fixed data-2
B2 Fixed data-1 (Initialized data)
B3 Fixed data-2
B4, B5 Fixed data-1 (Initialized data)
B6 Fixed data-2
B7 Fixed data-1 (Initialized data)
B8 Fixed data-2
B9 to BF Fixed data-1 (Initialized data)
C0 Fixed data-2
C1 to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
10 Fixed data-2
Remark
6-10
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
8. F Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address
10 80 80 28 MHz origin osillation adj.
11 Fixed data-1 (Initialized data)
12 4A 4A
13 56 56
14 11 11
15 20 20
16 02 02
17 E0 E0
18, 19 Fixed data-1 (Initialized data)
1A 00 00
1B 60 60
1C to 29 Fixed data-1 (Initialized data)
2A 1B 1B
2B 00 00
2C 07 07
2D 00 00
2E 0E 0E
2F 00 00
30 0D 0D
31 00 00
32 Fixed data-1 (Initialized data)
33 22 22 Color reproduction adj.
34 Fixed data-1 (Initialized data)
35 27 24 Color reproduction adj.
36 to 39 Fixed data-1 (Initialized data)
3A 00 00
3B F1 EF
3C, 3D Fixed data-1 (Initialized data)
3E 29 2A
3F 80 C0
40 58 5A
41 C0 C0
42, 43 Fixed data-1 (Initialized data)
44 28 28
45 EC EC
46 35 35
47 8F 8F
48 13 13
49 B8 B8
4A 00 00
4B 00 00
4C 00 00
4D 00 00
4E 2B 2B
Initial value
NTSC PAL
Remark
Hall adj.
LV standard data input
Auto white balance
standard data input
Auto white balance adj.
Color reproduction adj.
Auto white balance adj.
Flange back adj.
Address
4F 19 19
50 00 00
51 32 32
52 04 04
53 00 00
54 00 00
55 to 57 Fixed data-1 (Initialized data)
58
59
5A FF FF Optical axis adj.
5B to 8D Fixed data-1 (Initialized data)
8E
8F Fixed data-2
90
91 to 96 Fixed data-1 (Initialized data)
97 Fixed data-2
98 to A5 Fixed data-1 (Initialized data)
A6 Fixed data-2
A7 to AC Fixed data-1 (Initialized data)
AD
AE
AF
B0
B1 to C4 Fixed data-1 (Initialized data)
C5
C6
C7 to E0 Fixed data-1 (Initialized data)
E1 Fixed data-2
E2 to EA Fixed data-1 (Initialized data)
EB Fixed data-2
EC to EE Fixed data-1 (Initialized data)
EF Fixed data-2
F0 to FF Fixed data-1 (Initialized data)
9. 1F Page table
Note 1: If reading/writing data on pages 1F , set data: 01 to page:
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
Address
00 to 1D Fixed data-1 (Initialized data)
1E Fixed data-2
1F to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Flange back adj.
Fixed data-2
Fixed data-2
Fixed data-2
0, address: 10, and then select pages F. By this data setting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Initial value
NTSC PAL
Remark
Remark
6-11
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-3. CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the
specified values of “28 MHz Origin Oscillation Adjustment”, “S
VIDEO OUT Y level Adjustment” and “S VIDEO OUT C level
Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisf ied.
Check that the data of page: 0, address: 10, is “00”.
If not, select page: 0, address: 10, and set data “00”
1. HALL Adjustment
For detecting the position of lens iris, adjust the hall AMP gain
and offset.
Mode CAMERA
Subject Not required
Measurement Point Displayed data of page: 1 (Note 3)
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 12 to 17
Specified value 87 to 8B during IRIS OPEN
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: The right two digits of the page: 1 displayed data of the
adjusting remote commander.
1:00:
Adjusting method:
Order Page Address Data Procedure
10 0101
26 9489
36 9517
46 01 6D Press PAUSE button. (Note 4)
56 02
66 01 00 Press PAUSE button.
Note 4: The adjustment data will be automatically input to page:
F, address: 12 to 17.
RadarWRadarWRadarW
15 to 19 during IRIS CLOSE
XX
Displayed data
Check the data changes to
“01”.
Checking method:
Order Page Address Data Procedure
10 0303
26 01 01 Press PAUSE button.
Check that the displayed data
31
46 01 03 Press PAUSE button.
51
Processing after Completing Adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 9400
36 9500
40 0300
50 0100
(Note 3) during IRIS OPEN
satisfied the specified value.
Check that the displayed data
(Note 3) during IRIS CLOSE
satisfied the specified value.
6-12
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
RadarWRadarWRadarW
2. Flange Back Adjustment
(Using the minipattern box)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing.
Mode CAMERA
Subject Siemens star chart with ND filter for
minipattern box (Note 1)
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Note 1: Dark Siemens star chart.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 4: Perform the adjustment with the camcorder in horizon-
tal state.
Note 5: Perform “HALL Adjustment” before this adjustment.
Switch setting:
1) NIGHTSHOT PLUS........................................................ OFF
2) DISPLAY (Menu setting) ............................................... LCD
Preparations before adjustments:
1) The minipattern box is installed as shown in the following f igure.
Note 6: The attachment lenses are not used.
2) Install the minipattern box so that the distance between it and
the front of lens of camcorder is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the
specified voltage ± 0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of
shot image screen with the zoom lens at TELE end and WIDE
end respectively.
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
46 01 27 Press PAUSE button. (Note 7)
56 02
Check the data changes to
“01”.
Note 7: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after Completing Adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6
Perform “Flange Back
Check”.
Specified voltage: The specified voltage varies according to the
minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.
Below 3 cm
Minipattern box
Camcorder
Camera
table
Output voltage : Specified voltage ±0.01 Vdc
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Regulated power supply
Output current : more than 3.5 A
Need not connected
Fig. 6-1-6
6-13
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
RadarW
RadarW
3. Flange Back Adjustment
(Using the flange back adjustment chart and
subject more than 500 m away)
The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
RadarW
RadarW
3-1. Flange Back Adjustment (1)
Mode CAMERA
Subject Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: Perform the adjustment with the camcorder in horizon-
tal state.
Note 4: Perform “HALL Adjustment” before this adjustment.
Switch setting:
1) NIGHTSHOT PLUS........................................................ OFF
2) DISPLAY (Menu setting) ................................................ LCD
Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front
of the lens.
2) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
46 01 15 Press PAUSE button. (Note 5)
56 02
Note 5: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after Completing Adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6
RadarW
Check the data changes to
“01”.
Perform “Flange Back
Adjustment (2)”.
3-2. Flange Back Adjustment (2)
Perform this adjustment after performing “Flange Back Adjustment (1)”.
Mode CAMERA
Subject Subject more than 500 m away
(Subject with clear contrast such as
buildings, etc.)
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Switch setting:
1) NIGHTSHOT PLUS........................................................ OFF
2) DISPLAY (Menu setting) ................................................ LCD
Preparations before adjustments:
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away.
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
4
56 01 29 Press PA USE b utton. (Note 3)
66 02
Note 3: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after Completing Adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6
RadarWRadarWRadarW
Place ND filter on the lens so
that the optimum image is
obtain.
Check the data changes to
“01”.
Perform “Flange Back
Check”.
6-14
Loading...