NAIL STUDIO SET SNS 45 B4
NAIL STUDIO SET
Operating instructions
KOMPLET ZA UREJANJE NOHTOV
Navodila za uporabo
NECHTOVÉ ŠTÚDIO
Návod na obsluhu
IAN 275423
KÖRÖMÉPÍTŐ KÉSZLET
Használati utasítás
SADA NA ÚPRAVU NEHTŮ
Návod k obsluze
NAGELSTUDIO-SET
Bedienungsanleitung
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB Operating instructions Page 1
HU Használati utasítás Oldal 35
SI Navodila za uporabo Stran 69
CZ Návod k obsluze Strana 101
SK Návod na obsluhu Strana 135
DE / AT / CH Bedienungsanleitung Seite 169
A
B
.
3
-!
0
6
1
%
,
+
Table of Contents
Introduction ..............2
Copyright .....................2
Limitation of Liability .............2
Intended Use ..................2
Warning Notices ...............3
Safety instructions .........4
Appliance and Accessories . . . 11
Setting up and connecting
to the power supply .......12
Safety instructions ..............12
Items supplied and
initial inspection ...............12
Unpacking ...............13
Disposal of packaging ..........13
Requirements for the installation
location ......................13
Electrical connection ............14
Handling and operation . . .15
Switching On and Off ..........15
Functions .....................15
Utilisation ...............16
Selecting artificial nails ..........16
Attaching artificial nails .........17
Matching a nail set .............20
Application of the UV-Gel .......20
Hardening of the UV-Gel ........21
Topping up ...................23
French nails ...................24
Removal of artificial nails ........24
Care ........................25
Cleaning ................25
Safety instructions ..............25
Cleaning the appliance .........25
Cleaning accessories ...........26
Exchanging the UV Lamps . . . 26
Troubleshooting ..........28
Safety instructions ..............28
Malfunction causes and remedies . . . 29
Storage/Disposal .........30
Storage ......................30
Disposing of the appliance .......30
Appendix ...............30
Notes on the EC Declaration
of Conformity .................30
Technical data ................31
Kompernass Handels
GmbH warranty ..........31
Service ......................33
Importer .....................33
SNS 45 B4
GB
│
1 ■
Introduction
Congratulations on the purchase of your new appliance.
You have clearly decided in favour of a quality product. These operating instruc-
tions are a part of this product. They contain important information in regard to
safety, use and disposal. Before using the product, familiarise yourself with all of
these operating and safety instructions. Use the product only as described and
only for the specified areas of application. In addition, pass these documents on,
together with the product, to any future owner.
Copyright
This documentation is copyright protected.
Any copying or reproduction, including as extracts, as well as the reproduction of
images, also in an altered state, is only permitted with the written authorisation of
the manufacturer.
Limitation of Liability
All technical information, data and information for connection and operation, contained in these operating instructions correspond to the latest at the time of printing and, to the best of our knowledge, take into account our previous experience
and know-how. No claims can be derived from the details, illustrations and descriptions in these instructions. The manufacturer assumes no responsibility for damage
caused by failure to observe the instructions, improper use, inappropriate repairs,
making unauthorized changes or for using unapproved replacement parts.
Intended Use
This appliance is intended only for the application and fixating of artificial finger
nails for manicure purposes in indoor areas and is only for domestic use. This appliance is not intended for any other use or for uses beyond those mentioned here.
■ 2 │ GB
WARNING
Risks from unintended use!
Risks can be engendered by the appliance if it is used for unintended
purposes and/or other types of use.
► Use the appliance exclusively for intended purposes.
► Observe the procedures described in these operating instructions.
SNS 45 B4
Claims of any kind resulting from damage caused by improper use, incompetent
repairs, unauthorized modifications or the use of non-approved spare parts will
not be acknowledged.
The operator alone bears liability.
Warning Notices
In the existing operation instructions the following warnings are used:
DANGER
A warning at this risk level indicates a threateningly dangerous
situation.
If the dangerous situation is not avoided it could lead to death or serious physical
injuries.
► Observe the directives in this warning notice to avoid the risk of deaths or
serious physical injuries.
WARNING
A warning at this risk level indicates a possibly dangerous
situation.
If the dangerous situation is not avoided, this could lead to personal injury.
► Follow the instructions in this warning to avoid personal injuries.
IMPORTANT
A warning at this risk level signifies possible property damage.
If the situation is not avoided it can lead to property damage.
► The directives in this warning are there to avoid property damage.
SNS 45 B4
NOTICE
► A notice signifies additional information that assists in the handling of the
appliance.
GB
│
3 ■
Safety instructions
This appliance complies with the statutory safety regulations. Incorrect usage can, however,
lead to personal and property damage.
■ A repair to the appliance during the warranty period may only be carried out by a customer
service firm authorised by the manufacturer, otherwise no additional warranty claims can be
considered for subsequent damages.
DANGER
Potentially fatal risk of electrical shocks!
Upon contact with live wires or live components
there is a potentially fatal risk!
Pay heed to the following safety information to avoid a potentially fatal risk from electrical power:
► To avoid potential risks, if the appliance power cable is dam-
aged, it must be replaced by the manufacturer, its Customer
Service or by a qualified technician.
► Do not instal the appliance in the bathroom.
► Connect the appliance exclusively to a correctly fused mains
power socket.
► Do not touch the appliance and the plug with wet hands.
► NEVER place the appliance in water.
► Do NOT open the housing of the appliance (except when
changing the UV lamps). If live connections are touched
and/or the electrical or mechanical construction is altered,
there will be an increased risk of electric shock.
WARNING
Risk of injury from ultraviolet light (UV-Light)!
Looking directly into the UV light from the UV lamps in this appliance can cause eye injuries and diminish the power of your vision!
► NEVER look directly into the ultraviolet light from the UV lamps.
► If the UV lamps are not in use, switch them off.
► Non-users, and especially children, may not be present during
the operation of the appliance.
■ 4 │ GB
SNS 45 B4
WARNING - RISK OF INJURY
► Before use check the appliance for visible external damage.
Do not put into operation an appliance that is damaged or
has been dropped.
► Children should be supervised to ensure that they do not
play with the appliance.
► Never look directly into the UV lamps. It could cause injury
to the eyes!
► Always keep the appliance and all accessories out of the
reach of children.
► Pay heed to the instructions given on the containers of all
substances used.
► Repairs should only be carried out by authorised specialist
companies or by the Customer Service Department. Incorrect
repairs can result in significant risks for the user. In addition,
warranty claims become void.
► Defective components may only be replaced with original
replacement parts. Only by using these replacement parts
can it be guaranteed that they comply with the safety requirements.
SNS 45 B4
GB
│
5 ■
WARNING
Risks of damage to health from solvent-containing
substances and vapours!
The inhalation of solvent-containing substances and vapours
can damage your health!
► Do not breathe in the vapours from solvent-containing sub-
stances (e.g. acetone).
► Ensure there is adequate ventilation when interacting with
solvent-containing substances.
► Pay heed to the instructions on the containers of the solvent-
containing substances.
WARNING
Risks of health damage from chemical substances!
The improper handling of chemical substances can lead to serious
health damage!
► If swallowed, IMMEDIATELY seek medical attention!
► In cases of allergic reactions, consult a doctor immediately!
► In the event of contact with the eyes or mucous membranes,
contact a doctor immediately!
■ 6 │ GB
SNS 45 B4
INFORMATION ON HANDLING
CHEMICAL SUBSTANCES
The chemical substances supplied with this product include the
nail glue, the finishing solution, the UV gel and the French gel.
► Open the pots and jars containing the chemical substances
carefully.
► Handle the chemical substances cautiously and with care.
► The chemical substances are irritating to the eyes and skin.
► The chemical substances can cause skin irritations (sensitisa-
tion of the skin).
► Ensure that there is sufficient ventilation when you are working
with the chemical substances. If there is insufficient ventilation,
wear breathing apparatus.
► Never use the UV gel or the French gel on damaged or
unhealthy nails, or for repairing damaged nails.
► Keep the chemical substances out of the reach of children!
ATTENTION - PROPERTY DAMAGE
► Protect the appliance from moisture and the penetration of
liquids. NEVER immerse the appliance in water or place the
appliance in the close vicinity of water and DO NOT place
objects filled with liquids (e..g. vases) onto the appliance.
► Do not place any objects on the appliance.
► Do not operate the appliance close to open flames (e.g.
candles).
► Avoid direct solar radiation.
► Always pull the plug itself out of the mains power socket, do
not pull it with the power cable.
► In the case of a malfunction occurring or a thunderstorm,
disconnect the plug from the mains power socket.
SNS 45 B4
GB
│
7 ■
WARNING - RISK OF INJURY!
UV appliances may not be used by:
► People who suffer from skin cancer or are predisposed to it,
► People, who are taking light-sensitivity enhancing drugs,
► People under 18 years of age,
► People with a tendency towards freckles,
► People with a naturally red hair colour,
► People with unusual skin discolourations,
► People with more than 16 moles (with a minimum diameter
of 2 mm) on their body,
► People with atypical moles (atypical moles are asymmetri-
cal moles with a diameter of more than 5 mm and different
pigmentation plus irregular border areas; if in doubt, consult
your doctor),
► People who are suffering from sunburn,
► People who do not tan in the sun without skin burns,
► People who quickly suffer from skin burns in direct sunlight,
► People who have frequently suffered from a severe sunburn
during their childhood,
► People who suffer from skin cancer or are suffering from this
disease or are susceptible to skin cancer,
► People with a first-degree relative who is suffering or has
already suffered from a melanoma (skin cancer),
► People who, due to a light sensitivity ailment, are in physi-
cianly or medical treatment,
► People who absolutely cannot tan at all, or who cannot tan
without getting sunburned, when they are exposed to the sun,
► People who are easily sunburned when they are exposed to
the sun,
► during pregnancy.
■ 8 │ GB
SNS 45 B4
■ The irradiation should not exceed the minimal erythema dose
(MED). If erythema (skin redness) occurs several hours after irradiation there should be no further applications made. In this case,
the next irradiation should not take place before one week after the
date of the skin redness.
■ If unexpected side effects such as itching occur within 48 hours
after the first application of the UV appliance, you should consult
a doctor before receiving further UV irradiation.
■ Recommended exposure timetable:
– Do not carry out more than 5 treatments per day. This could
lead to skin irritation.
– Do not exceed the recommended number of 400 treatments per
year.
■ The appliance may not be used if the timer is not working properly.
■ Use only lamps of the specified type. The use of a UV lamp from
another manu-facturer or of a different type will lead to the revocation of the warranty.
■ UV radiation from the sun or from UV appliances can cause both
skin and eye damage, which may be irreversible. These biological effects depend on the quality and quantity of the radiation
and on the skin and eye sensitivity of the individual person.
■ The skin can suffer from sunburn after excessive exposure to ra-
diation. Too frequent UV radiation from the sun or UV appliances
can lead to premature skin aging and cause an increased risk of
skin cancer. This risk increases with increasingly cumulative UV
exposures. UV radiation at a young age increases the subsequent
risk of skin cancer.
■ UV radiation can lead to injuries to the eyes and skin, such as
premature skin aging and even skin cancer. Read these operating
instructions carefully. Some medications or cosmetics increase the
sensitivity to UV radiation.
SNS 45 B4
GB
│
9 ■
■
The unprotected eye can suffer superficial inflammation and, in
some cases, excessive exposure may cause damage to the retina.
Frequently repeated exposures can lead to cataracts.
■ In the event of individually identified sensitivity or allergic reactions to
UV radiation, you should first seek medical advice before beginning the irradiation.
■ Certain ailments or the side effects of certain drugs may be exac-
erbated by UV irradiation. If in doubt, consult your doctor.
■ There should be a period of at least 48 hours between the first
two exposures.
■ Avoid sunbathing and use of the appliance on the same day. This
could lead to skin irritation.
■ Pay heed to the instructions on the irradiation time, time intervals for the
irradiation and the distance to be from the lamp. If you do not, it
could lead to skin irritation.
■ Consult your doctor if persistent tumours or ulcers form, or
changes in moles come about or sores develop.
■ Protect sensitive skin areas, such as scars, tattoos and the geni-
tals, from irradiation.
■ Do not carry out more than 5 treatments per day. This could
lead to skin irritation.
■ Do not exceed the recommended number of 400 treatments per
year.
■ Remove cosmetics and sun care products before using the appli-
ance. If you do not, it could lead to skin irritation.
NOTICE
► If in any doubt, consult your doctor about the possible ap-
plications before using the appliance.
■ 10 │ GB
SNS 45 B4
Appliance and Accessories
NOTICE
► See in addition the illustrations on the fold-out side.
Figure A:
UV appliance with 4 built-in UV lamps
ON/OFF switch
Time selector button (SELECT)
Start button
Figure B:
Nail clippers (for clipping the nail-tips)
Cuticle pusher (to push back the cuticle)
Brush (for applying the UV Gel)
Sanding block (for smoothing of unevenness)
Fine polishing file (for polishing the nails “shine”)
Medium polishing file (for polishing the nails “condition”)
- Coarse polishing file (for polishing the nails “clean”)
3 Cellulose pads (for applying the finishing solution or for correction)
! Spot swirl (for applying French gel or decorative elements)
. Sandpaper file (for filing nails)
0 Nail tips (artificial fingernails)
6 Finishing solution (for final treatment and for cleaning brushes)
1 Nail glue (to glue the “GLUE” nail tips on)
% UV gel (for topping up nails)
+ French gel (for modelling “French nails”)
, Nail oil (for conditioning the cuticle “Nail Care”)
SNS 45 B4
GB
│
11 ■
Setting up and connecting to the power supply
Safety instructions
WARNING
During the commissioning of the appliance personal injury and
property damage could occur!
Observe the following safety information to avoid these risks:
► Packaging material should not be used as a play thing. There is a risk of
suffocation.
► To avoid damage to people and property, pay heed to the requirements
for the installation site and the electrical connection of the appliance.
Items supplied and initial inspection
The appliance is supplied with the following components as standard:
Ɣ UV appliance with 4 UV lamps and mains power cable
Ɣ Sand sheet file
Ɣ Polishing files (coarse, medium, fine)
Ɣ Sanding block
Ɣ Nail Tips
Ɣ Cuticle pusher
Ɣ Brush
Ɣ Spot swirl
Ɣ Nail clippers
Ɣ 1 pot French gel (“French gel”)
Ɣ 2 pots of UV gel (“UV Gel”)
Ɣ Finishing solution (“Finishing”)
Ɣ 2 bottles of nail glue (“Glue”)
Ɣ 1 bottle of nail oil (“Nail Care”)
Ɣ 100 cellulose pads (cellulose tissues)
Ɣ Storage case
Ɣ Operating instructions
■ 12 │ GB
SNS 45 B4
NOTICE
► Check the contents to ensure everything has been provided, and for signs
of visible damage.
► If the contents are incomplete, or have been damaged due to defective pack-
aging or transportation, contact the Service Hotline (see chapter Service).
Unpacking
Ƈ Remove all parts of the appliance and these operating instructions from the box.
Ƈ Remove all packing material.
Disposal of packaging
The packaging protects the appliance against transport damage. The packaging
materials are selected from the point of view of their environmental friendliness
and disposal technology and are therefore recyclable.
The recirculation of packaging into the material circuit saves on raw material and
reduces generated waste. Dispose of packaging material that is no longer needed
according to the regionally established regulations.
NOTICE
► If possible preserve the appliance's original packaging during the warranty
period so that, in the event of a warranty claim, you can package the appliance properly for its return.
Requirements for the installation location
For the safe and trouble-free operation of the appliance the following requirements
must be met at the installation location:
■ Place the appliance on a dry, flat and firm surface.
■ Do not place the appliance in a damp environment and not in an area at risk
from spraywater.
■ Do not place the appliance adjacent to a radiator or a raiation heater.
■ The mains power socket must be easily accessible, so that the plug can be
easily removed in an emergency.
SNS 45 B4
GB
│
13 ■
Electrical connection
DANGER
Potentially fatal risk of electrical shocks!
Upon contact with live wires or live components there is a
potentially fatal risk!
Pay heed to the following safety information to avoid risks from electrical power:
► Do not operate the appliance if the plug or the power cable are damaged.
► Connect the appliance exclusively to a correctly fused mains power socket.
► Do not touch the appliance and the plug with wet hands.
► Avoid water contact with the appliance.
► DO NOT open the housing of this appliance. If live connections are
touched and/or the electrical or mechanical construction is altered, there
will be an increased risk of electric shock.
Ƈ Before you connect the appliance, compare the connection data (voltage and
frequency) on the typeplate of the appliance with that for the intended power
source. his data must match, in order to avoid any damage to the appliance.
Ƈ Ensure that the power cable of the appliance is not damaged and that it is not
laid over hot surfaces and/or sharp edges.
Ƈ Ensure that the power cable is not over-taut or kinked.
Ƈ Do not let the power cable hang over edges (trip wire effect).
Ƈ Insert the plug into the mains power socket.
■ 14 │ GB
SNS 45 B4
Handling and operation
In this chapter you receive important information for the handling and operation
of the appliance.
NOTICE
► See also the chapter Appliance and Accessories.
Switching On and Off
Ƈ Switch on the UV appliance by pressing the ON/OFF switch to the
position “I”. As soon as the appliance is switched on, the blue points on the
appliance light up.
Ƈ Switch off the UV appliance by pressing the ON/OFF switch to the
position “0”.
Functions
Three different treatment times can be set on the appliance:
■ 90 seconds
■ 150 seconds
■ 240 seconds
Ƈ Press the Start button . “90” lights up and the UV lamps switch on.
Ƈ If you want to select another time, press the time selector button (SELECT)
repeatedly until the desired time lights up.
SNS 45 B4
NOTICE
► The UV lamps switch off automatically after the lapse of the preset time.
Ƈ Press the start button and the time selector button again as described
above for each further treatment.
│
GB
15 ■
Utilisation
CAUTION
Risk of property damage from glue and UV gel.
Nail glue 1, UV gel % and French gel + are very difficult to remove from
furniture surfaces, clothes and carpets.
► Cover your work area with paper or with a hand towel prior to use.
NOTE
► Place the UV appliance on a covered, stable surface.
► Never place the nail glue 1, the French gel + or the UV gel % in the
vicinity of the UV appliance .
► Never expose the nail glue 1, the French gel + or the UV gel % to direct
sunshine.
Selecting artificial nails
NOTICE
► For the first applications it may be helpful to be assisted by an experienced
person.
► Before the application, remove all jewelry on the hands.
► Clean and dry your hands before the application. We recommend that the
hands are washed about 15 - 20 minutes before the application, so that
there will be no residual moisture on the nails.
Ƈ Select a nail tip 0 whose curvature corresponds as closely as possible to the
natural curve of your nail.
0
■ 16 │ GB
Ƈ Select a nail tip 0 which closes exactly at the edge of your natural nail and
whereby the sides are parallel to your natural nail.
SNS 45 B4
Ƈ If necessary, file the ends of the nail tips . with the sandpaper file 0, so that
the end point (arrow) covers about one third of your natural nail.
0
Free edge Nail bed
Nail plate Cuticle
NOTICE
► If you use a too small nail tip 0, it can break off more easily. Therefore,
select a larger nail tip 0 and then file the sides into the desired form.
Ƈ Repeat the described process until all of your nails have the desired length
and shape.
Attaching artificial nails
NOTICE
► Take note that nails absorb moisture from contact with water. The nails,
however, must be completely dry before the application.
► Before the application, refrain from using any hand creams or the like,
because, to make possible the optimal adhesion of the nail tips 0 the nail
surfaces must be completely free from greases.
Ƈ Push the cuticle back with the cuticle pusher and then remove the trans-
parent skin from the nail plate of your finger.
Ƈ Now treat the nail surface with the sanding block until the fingernail is no
longer shiny.
Ƈ Remove the dust from filing with a paper cloth or cellulose pad 3.
Ƈ Rub the nails with the finishing solution 6 so that the last remnants of dust
and grease are removed.
SNS 45 B4
GB
│
17 ■
NOTICE
► Under no circumstance should you now touch the nail surfaces with your
fingers, if you do, they will become greasy again and this will prevent a
good bonding!
Ƈ Apply a small drop of nail glue 1 to the lower part of the nail tip 0 and
distribute it with the aid of the nail glue bottle 1 on the lower surface. Hold
the nail tip 0 down so that the nail glue 1 cannot run onto the upper part
of the nail tip 0.
NOTICE
► Dab the nail tip 0briefly with a cellulose pad 3 to remove any excess
nail glue 1.
1
NOTICE
► Before the first use you must puncture the bottle of nail glue 1 with a
pointed object, such as a needle. If, at a later date, the bottle of nail glue 1
has become blocked, it can again be opened for use with a needle.
Ƈ Now place the nail tip 0 at an angle on the natural nail, so that the predeter-
mined edge of the nail tip 0 lies on the edge of the natural nail.
Ƈ Now tilt the nail tip 0 with gentle pressure onto the natural nail, so that po-
tential air bubbles are squeezed out .
■ 18 │ GB
0
SNS 45 B4
NOTICE
► Wipe off excess nail glue 1 with a cellulose pad 3.
Ƈ Hold the nail tip 0 firmly for 10-12 seconds and, at the same time, press it
down with sufficient pressure onto the natural nail. Ensure that no air bubbles
are formed and that the tip is glued on perfectly straight.
NOTICE
► There may no longer be a gap under the nail, so that dirt cannot penetrate.
► Ensure that no air bubbles or white spots form under the nail tip 0. In this
case, take the nail tip 0 off immediately and lay it back on again.
Ƈ When you have glued all of the nail tips 0 on, trim them to the desired length
with the nail clippers . Press the nail clippers together in one squeeze. If
you press too slowly, it may happen that the nail tips 0 splitter.
Ƈ File them into shape with the sandpaper file ..
SNS 45 B4
NOTICE
► File very carefully, because the nail tips 0 are held only with a nail glue 1.
► If you are not used to long nails, cut the nail tips 0 back a little in order to
avoid knocks and prevent the nail tips 0 from falling off
│
GB
19 ■
Matching a nail set
Ƈ Carefully file the transitions from the nail tips 0 to the natural nails with the
Sandpaper file ., until they conform to the contour of the natural nail. File
only the nail tips 0! Do not damage your natural nail.
Ƈ Carefullly file the sides of the nail with the Sandpaper file .until it is straight
and does not exhibit a “wing”.
Ƈ File the nail tip 0 first with the sandpaper file . and then with the sanding
block . The nail tip 0should no longer shine.
Ƈ Repeat this step for each individual nail.
Ƈ Remove the dust from filing with a paper cloth or cellulose pad 3.
Application of the UV-Gel
Ƈ Using the brush , take a small amount of UV Gel % and then wipe the
excess on one side of the brush off on the edge the UV Gel pot.
Ƈ Apply a thin coating of UV-Gel % onto the complete nail. Apply a little more
UV Gel % to the lower part of the nail, as hereby is how the offset between
the natural and the artificial nail is created. Furthermore, the transition from
natural to artificial nails is especially sensitive to pressure and knocks, thus
more UV Gel % must be applied here.
.
■ 20 │ GB
INFORMATION
► When you are doing the application do not press too heavily on the brush ,
since the brush could otherwise cause streaking.
► Model the first layer of the UV Gel % very carefully, as this determines the
future shape of the nail. Model the best possible natural nail shape.
Ƈ Maintain a distance of about 1 mm from the cuticle during the application.
SNS 45 B4
NOTICE
► Should any UV Gel % inadvertantly come onto the cuticle or the nail bed,
remove it before the hardening, for example, with a cotton wool swab.
Ƈ Repeat the above process for all nails.
0
NOTICE
► Ensure that the nail is covered evenly with UV Gel %.
Hardening of the UV-Gel
NOTICE
► See also the chapter Handling and operation.
Ƈ Switch on the UV appliance with the ON/OFF switch .
Ƈ Press the start button .
Ƈ Use the time selector button to select the required treatment time. For the
first hardening we recommend the time setting of 240 seconds.
Ƈ Hold your hand with the nails upward for the duration of the set treatment
time in the opening of the UV appliance .
Ƈ Treat the thumbnail separately because, when you hold your hand in the UV
appliance , the UV light only shines on the side of it.
Ƈ Repeat the application of the UV gel % and the hardening in the UV appli-
ance as described above.
SNS 45 B4
NOTICE
► To improve the stability of the nails, apply several thin coats of UV gel %
and harden them each separately.
│
GB
21 ■
NOTICE
► After the expiry of the preselected treatment time the UV lamps are switched
off automatically.
► The start button and the time selector button must be activated again
for each new treatment.
Ƈ Examine each nail, after the application and hardening of all coatings, for
unevenness, small scratches or ridges.
Ƈ If you discover unevenness, apply a further thin layer of UV gel % and hard-
en the nail with the setting of 150 seconds or 90 seconds (depending on the
amount of applied UV gel %).
Even after the last hardening of the Gel layer, the nails may feel a feel sticky
(“sweat-layer” or polymerization layer).
Ƈ Moisten a cellulose pad 3 with finishing solution 6 and then wipe this over
the nail.
■ 22 │ GB
SNS 45 B4
TIP
► If you want to apply ornaments or small rhinestones to the nail, use the
Ƈ To finish, apply a coating of clear varnish onto the nail to give it a gloss finish.
Ƈ For care, add a little nail oil , to the cuticle.
Topping up
NOTICE
► Because the natural nail grows, over time the attachment of the nail tip 0
► A topping up is required about every 2 - 3 weeks.
Ƈ Using the sandpaper file ., file around the attachments of the hardened gel.
Ƈ Use the sanding block until the nail is no longer shiny.
Ƈ When done, reapply UV gel % and harden it again.
NOTICE
► In this regard, see the previous chapters Application of the UV-Gel,
sharp side of the Spot swirl to place them in the non-hardened most
recent layer of the UV gel %. Then harden the UV gel %.
Apply an additional, very thin layer of UV gel % over the nail and then
harden it to ensure that the ornaments are held firmly in place. This gives
the ornaments better protection.
can raise itself. For this reason the gap between the cuticle and the nail
attachment must be topped up from time to time.
Hardening of the UV-Gel.
SNS 45 B4
GB
│
23 ■
French nails
“French nails” means decorating the fingernails with a white tip.
Ƈ Model the nail as described in the chapter entitled “Application” until you
have applied the first layer of UV gel % and hardened it.
Ƈ Use the round application side of the Spot swirl ! to apply French gel + to
the nail tip. Always take up new French gel + with the point and model the
white nail tip with light circular movements.
Ƈ Proceed with the other nails in the same way.
Ƈ Now harden the nail using a setting of 150 seconds.
Ƈ Then apply an additional layer of UV gel %. Apply a little less UV gel %
to the white part of the nails than to the rest. This makes the transition to the
white tip disappear.
Ƈ Now harden the nail using a setting of 150 seconds. After the last hardening
of the gel layer, the nails may feel a little sticky (“sweat layer” or polymeriza-
tion layer).
Ƈ Moisten a cellulose pad 3 with finishing solution 6 and then wipe this over
the nail.
Removal of artificial nails
IMPORTANT
Risk of damaging the natural nail surface!
A forcible breaking-off of the nail tips 0 can cause damage to the natural nail
surfaces!
► Do not break the nail tips 0 off of the natural nails.
► Remove the nail tips 0 only in accordance with the following description.
Ƈ First file the nails right back with the sandpaper file ..
Ƈ Then file the nail tips 0 off with the sandpaper file ..
Ƈ Polish your nails with the polishing files -.
■ 24 │ GB
TIP
► Afterwards, apply a little nail oil , to care for your natural nails.
SNS 45 B4
.
Care
■ Regularly file the attachments and nail edges.
■ Use the nail oil , or a little hand cream regularly.
■ When applying nail varnish, use both a lower layer and an upper layer.
■ Do not use an acetone-based nail polish remover for removing nail polish,
because this would loosen and damage the artificial nails.
■ Wear rubber gloves when using detergents or bleaching agents.
■ Wear a pair of rubber gloves for all work/activities that may damage the
nails.
Cleaning
Safety instructions
-
DANGER
Potentially fatal risk of electrical shocks!
► Disconnect the plug from the mains power socket before you start cleaning
the appliance.
IMPORTANT
Damage to the appliance!
► To avoid irreparable damage, ensure that no moisture can penetrate inside
the UV appliance when you are cleaning it.
Cleaning the appliance
Ƈ Clean the surfaces of the UV appliance only with a soft and dry cloth.
Wipe the base plate with a damp cloth.
SNS 45 B4
GB
│
25 ■
Cleaning accessories
NOTICE
► Clean the brush and the Spot swirl ! immediately after every use.
Always close all bo
►
Ƈ Keep the br
wipe them both off with a paper towel.
ttles and tubs after use
ush and the Spot swirl!in the finishing solution 6 and then
Exchanging the UV Lamps
DANGER
Potentially fatal risk of electrical shocks!
► Disconnect the plug from the mains power socket before you start with the
exchange of the UV lamps!
NOTICE
► The UV lamps may ONLY be replaced with lamps of the same type. The speci-
fications for the precise lamp type are given in the chapter "Technical Data".
UV lamps of this kind are available in specialist retailers.
Ƈ Remove the base plate from the appliance.
.
■ 26 │ GB
SNS 45 B4
Ƈ Undo the screw with a Phillips screwdriver.
Ƈ Remove the front cover.
Ƈ Pull out the transparent protective disc.
Ƈ You can now carefully pull the defective UV lamp out of its socket.
Ƈ Insert the new UV lamp into the socket.
Ƈ Push the transparent protective disc back into the slot.
Ƈ Push the front cover back onto the appliance and fix it into place with the
screw.
Ƈ Push the base plate back into the appliance.
SNS 45 B4
GB
│
27 ■
Loading...