Seaga CM1250 Installation Manual

$250 Capacity ChangeMaker

Operator’s Manual

1

INTRODUCTION

Congratulations on the purchase of your new ChangeMaker. This ChangeMaker has been designed to give you many years of
dependable service. It requires little maintenance and is easy to set up and operate.

READ THIS MANUAL COMPLETELY

Your ChangeMaker is designed to operate simply and reliably, but to take full advantage of your vendor, please read this owner’s
manual thoroughly. It contains important information regarding installation and operations, as well as a brief trouble-shooting guide.

EQUIPMENT INSPECTION

After you have received your machine and have it out of the box, place it on a secure surface for further inspection. Note: Any
damages that may have occurred during shipping must be reported to the delivery carrier immediately. Reporting damages and the
seeking of restitution is the responsibility of the equipment owner. The factory is willing to assist you in this process in any way
possible. Feel free to contact our Customer Care Department with questions you may have on this process. It is important that you
keep the original packaging for your vending machine at least through the warranty period. If your machine needs to be returned for
repair, you may have to purchase this packaging if it is not retained.

Once your have your vendor located, we suggest that you keep this manual for future reference, or you can view this manual online
at www.seagamf g.com
designed to help you quickly identify a problem and correct it.

. Should any problems occur, refer to the section entitled “COMMON QUESTIONS AND ANSWERS”. It is

MANUFACTURER’S WARRANTY

WHAT IS COVERED:

Manufacturer warrants TO THE ORIGINAL PURCHASER ONLY that each item of equipment manufactured is free from defects in
material and workmanship under normal use and service. Manufacturer’s obligation under warranty shall be limited to repair or
replacement, at our plant, of any parts of the equipment, which shall, within one year of the date of shipment to the original
purchase, be demonstrated to be defective. The original purchaser may obtain repair or replacement of the equipment under
warranty by returning the defective item or entire vendor to the Manufacturer, freight prepaid.

WHAT IS NOT COVERED:

Manufacturer’s warranty obligations DO NOT EXTEND TO OR INCLUDE installation expenses, vandalism, or difficulties resulting
from failure to operate equipment in accordance with Manufacturer’s instructions under competent supervision and difficulties due to
changes in vended products, which are beyond the control of manufacturer.
SPECIAL NOTE: Manufacturer is not responsible for any loss of income due to a vending machine being out of service due to a
warrantable item.

This warranty is in lieu of all the other warranties, expressed or implied, including the warranty of merchantability and fitness or use,
and of all other obligations or liabilities on Manufacturer’s part. Manufacturer neither assumes, nor authorizes any other person to
assume for it, any other liability in connection with the sale of equipment manufactured by itself. This warranty shall not apply to
equipment manufactured or any part thereof which is subject to accident, negligence, alteration, abuse, misuse, or damage in
shipment. The term “original purchaser”, as used in this warranty, shall be deemed to mean that person for whom the equipment is
originally installed.

Manufacturer is not liable for any incidental, consequential or other damages of any kind whatsoever, directly or indirectly, arising
fr om the u se of th e equipment whether bas ed upon theor ies of co ntra ct negl igence or to r t.

For Service and Customer Care:
8:30 a.m. - 4:00 p.m. CST. Mon thru Fri

815.297.9500 ext 160

815.297.1758 Fax
email: customercare@sea gamf g.com

700 Seaga Drive

Freeport, IL 61032 U.S.A.

seagamfg.com

2

V

Figure 1 - $250 Capacit y ChangeM aker

Locks (2)

LED Readout

Validator Light

Bill Vali dator
Front Door
Coin Catcher

iew with door o pe n

Serial Decal

Circuit Board Cover
Bill Tray

Coin Hopper

Coin Hopper Assembl y

Diagnostic Button

Bill Vali dator

Programming Button

Your ChangeMaker has two (2) Locks. T o unlock the Front Door, turn left key count er-clockwise one-quart er turn and
the right key cl ockwise one-quart er t urn. T he Fr ont Panel will now swing open. A Chai n att aches the Fr ont Door to t he
Body for support.

The ChangeMaker has t hr ee (3) plugged holes in the left-hand side of the Case for optional m ounting. A drill, a ¼" dr ill
bit will be required along with sufficient hardware appropriate to your application and tools for this hardware. A
mounting template for drilling holes is provi ded.

1. To Mount:
a. Secure the templ ate to the mounting surface once you have made sure that nothing will obstruct the drilling

of holes or the placem ent of bolts.

LOCKS

MOUNTING

3