Samsung VP-L100, VP-L150 Alignment and Adjustments

Samsung Electronics 5-1

5. Alignment and Adjustment

5-1 Mechanical Adjustment

Test Point :

PB RF - Pin 45 of IC201
Head Switching Trigger - Pin 96 of IC601

Fig. 1 The location of test point

(PIN 45)

(PIN 96)

(PIN 67)

* Note 1 : Mechanical alignment is performed for the linearity of PB-RF(Envelope).
* Note 2 : Refer to the mechanism manual ÒDE-6Ó(AD68-30200A) for the mechanism alignment.

1) Short between pin #67 of IC601 and GND in order to set the TEST MODE.(ThatÕs Track Shift Mode)

2) Connect the Head SW Pulse in CH1 and the PB-RF in CH2 to oscilloscope.

3) Refer to the Fig1 for the location of test point.

4) Play the alignment tape supplied, and fit the PB-RF form like as Fig1.
(Refer to the alignment manual of the DE-6 described above).

5) If the alignment is completed, then remove the short wire for the release of the test mode.

Alignment and adjustment

5-2 Samsung Electronics

5-2 Camera Section Adjustment

Note :

1. This system has

1) EEPROM to store the confirmed adjustment data.

2) DSP (Digital Signal Process ; ICP04 - Main board) chip to process the signal of camera parts.

3) One test point for the frequency adjustment of DSP main clock (P. CLK).

2. Keep in mind

1) Readjustment is needed when the EEPROM (ICP10 of Main board) is replaced.
The reason is that EEPROM stores confirmed adjustment value of each adjustment step.

5-2-1 Preparations

1. Equipments to be used

1) DC Power supply

2) Oscilloscope

3) Frequency counter

4) Vectorscope

5) Waveform monitor

6) Color monitor or TV

7) Various charts

- Color bar chart

- Gray-scale chart, etc...

8) Alignment tape (Lion pattern)

2. Composition of camera P.C.Boards

1) Main PCB 2) CCD PCB

3) EVF PCB 4) LCD PCB

3. Adjustment preparations

1) Press the confirm button when each manual
adjustment step is completed to write the
adjustment data to the EEPROM.

2) After each adjustment step is completed, OSD
shows ÒOK!Ó.

3) To cancel the adjustment mode, remove the power
source.

4. Menu Board

The following is a chart explaining the use of each button :

Using Button

TITLE (CONFIRM)
C.RESET (DATA DOWN)
DISPLAY (DATA UP)
MENU (MODE UP)
DATE (MODE DOWN)
FADE (FAR )
BLC (NEAR)

Adjustment

Data store after finishing adjustment by DATA UP/DOWN button.
When changing data value of adjust state.

Mode change.

Focus adjustment.

Alignment and adjustment

Samsung Electronics 5-3

The function buttons on the Menu Board are used to control the camcorder additionally,

These buttons should be used for adjustment of the camera section.

Menu Board for camcorder adjustment

Figure of button placement when Menu Board is

used for service adjustment.

Reassignment

in the

adjustment mode

Note : In service adjustment mode, button names are different from those in customer camera function control

mode. EX) TITLE button is the same as confirm.

5. How to get into service ÒADJUSTÓ mode

1. Connect the power source (battery/
DC cable).

2. Eject the tape if it is in the unit.

3. Set the power switch of the
camcorder to ÒCAMERAÓ position.

4. Set OSD on state.

STEP 1

1. PRESS ÒDSEÓ Button 3 times on the camcorder.

2. It goes to into ÒNEGAÓ mode.

3. Press and hold the ÒEJECTÓ button and
ÒDISPLAYÓ button on the camcorder at the same
time for more than 3 seconds. Then unit goes into
service mode.

STEP 2

On screen display show “CD HALLA XX XX”
CAMERA ADJUSTMENT mode has successfully
been activated.

STEP 3

NEGA

OSD

Note : When ÒXX XXÓ is shown in service adjustment precedures, this indicates variable values.

Alignment and adjustment

5-4 Samsung Electronics

5. Initial data of camera parts adjustment - CAMERA AF 1st MICOM (UPD784035GC-820) DATA - NTSC

During camera adjustment, the OSD displays the following abbreviations to indicate the selected mode.

Note : ÒData 1Ó is previous setting in memory, ÒData 2Ó is

now adjustment setting, that changes during
adjustment mode. After pressing ÒTITLE (Confirm)Ó,
it goes to memory.

Example) “ 00 XXXX XX XX “

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
CD HALLA 70 70 70 70 HALL AUTO ADJUSTMENT
CE IRISRA D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT
CF WBA FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT
D0 LENSA FF FF FF FF LENS AUTO ADJUSTMENT
D6 Z.CHK 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT
O3 IRIS1 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE
O5 P.CLK 40 40 40 40 P.CLK ADJUSTMENT
O7 ADREF OO OO OO OO A/D REFERENCE CONTROL(SETUP)
O8 S.CLK 0F 0F 0F 0F SOFT CLIP CONTROL
O9 AGC1 18 18 18 18 AGC CONTROL
OB HAPER 58 58 58 58 HORIZONTAL APPERTURE GAIN
OC YSEL F8 F8 F8 F8 VERTICAL APPERTURE GAIN
1C CWBR 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL
1D CWBB 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL
32 CRGP 38 38 38 38 INDOOR R-Y POSITIVE GAIN
33 CRGN 38 38 38 38 INDOOR R-Y NEGATIVE GAIN
34 CHYE 09 09 09 09 INDOOR R-Y POSITIVE GAIN
35 CHB O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN
36 CBGP 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN
37 CBGN 18 18 18 18 INDOOR B-Y NEGATIVE GAIN
38 CHGR 18 18 18 18 INDOOR B-Y POSITIVE GAIN
39 PCBHN 01 01 01 01 INDOOR B-Y NEGATIVE GAIN
53 ECGAN 80 80 80 80 CHROMA GAIN CONTROL
54 ESY 83 83 83 83 Y SET-UP LEVEL CONTROL
55 EWC AE AE AE AE WHITE CLIP CONTROL
57 EUSC EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL
58 EVSC 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL
5D XKCON 00 00 00 00 SCK CONTROL
5E MDSEL 01 01 01 01 D/ZOOM MODE SELECTION
5F TGMSE 02 O2 O2 O2 TG MODE SELECTION
65 HRGDL 00 00 00 00 H1/H2/RG DELAY CONTROL
66 SHP.D D9 D9 D9 D9 SHP/SHD DELAY CONTROL
67 ADDL OO OO OO OO SPO/FECKDELAY CONTROL
71 ROUGP 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN
72 ROUGN 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN
73 CHOYE O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE
74 CHOB 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE
75 GOUGP 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN
76 BOUGN 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN
77 CHOGR 18 18 18 18 OUTDOOR B-Y POSITIVE HUE
78 CHOR 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE
82 AETAL 30 30 30 30 AE TARGET (LOW BYTE)
83 AETAH O5 O5 O5 O5 AE TARGET (HIGH BYTE)
88 AGCMA 85 85 85 85 AGC MAXIMUM CONTROL
8F WBTAR 84 84 84 84 WHITE BALANCE R TARGET
90 WBTAB 75 75 75 75 WHITE BALANCE B TARGET
95 R-IN 3C 3C 3C 3C R INDOOR CONTROL VALUE
96 B-IN 98 98 98 98 B INDOOR CONTROL VALUE
97 R-OUT 75 75 75 75 R OUTDOOR CONTROL VALUE

Alignment and adjustment

Samsung Electronics 5-5

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
98 B-OUT 5C 5C 5C 5C B OUTDOOR CONTROL VALUE
B8 CFAPS 20 20 20 20 NOISE SLICE START AGC
B9 APNSC FE FE FE FE NOISE SLICE MAXIMUM VALUE
BB CFAOR O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE
BC BLKST 30 30 30 30 EY BLACK START AGC
BD BLKMX O4 O4 O4 O4 EY BLACK MAXIMUM VALUE
00 OO OO OO OO NOT USED
01 40 40 40 40 HALL GAIN
02 80 80 80 80 HALL REFERENCE
03 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE
04 OO OO OO OO IRIS LEVEL CONTROL-L
O5 40 40 40 40 P.CLK ADJUSTMENT
06 OO OO OO OO P.CLK PWM CONTROL-L
O7 OO OO OO OO A/D REFERENCE CONTROL(SETUP)
O8 0F 0F 0F 0F SOFT CLIP CONTROL
O9 18 18 18 18 AGC CONTROL
OA 66 66 66 66 H/V BLACK NOIS THRESHOLD/GAIN
OB 58 58 58 58 HORIZONTAL APPERTURE GAIN
OC F8 F8 F8 F8 VERTICAL APPERTURE GAIN
0D 0B 0B 0B 0B APERTURE SLICE CONTROL
OE A8 A8 A8 A8 Y HI-REF. VALUE FOR C SUPRESS
OF 10 10 10 10 EDGE REF. VALUE FOR C SUPRESS
10 05 05 05 05 Y SIGNAL GAMMA COEFF. 1
11 0A 0A 0A 0A Y SIGNAL GAMMA COEFF. 2
12 1C 1C 1C 1C Y SIGNAL GAMMA COEFF. 3
13 30 30 30 30 Y SIGNAL GAMMA COEFF. 4
14 4D 4D 4D 4D Y SIGNAL GAMMA COEFF. 5
15 76 76 76 76 Y SIGNAL GAMMA COEFF. 6
16 B8 B8 B8 B8 Y SIGNAL GAMMA COEFF. 7
17 DA DA DA DA Y SIGNAL GAMMA COEFF. 8
18 OO OO OO OO Y LPF SELECTION
19 11 11 11 11 Cr/Cb/Y LPF SELECTION
1A 42 42 42 42 C MATRIX COEF. OF Cr SIGNAL
1B 66 66 66 66 C MATRIX COEF. OF Cb SIGNAL
1C 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL
1D 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL
1E 24 24 24 24 C W/B COEF. OF G SIGNAL
1F 05 05 05 05 C DARK SLICE COEF. OF Cr SIG.
20 01 01 01 01 C DARK SLICE COEF. OF Cb SIG.
21 FB FB FB FB C DARK SLICE COEF. OF G SIG.
22 05 05 05 05 C SIGNAL GAMMA BENDING POINT 1
23 0D 0D 0D 0D C SIGNAL GAMMA BENDING POINT 2
24 1A 1A 1A 1A C SIGNAL GAMMA BENDING POINT 3
25 38 38 38 38 C SIGNAL GAMMA BENDING POINT 4
26 58 58 58 58 C SIGNAL GAMMA BENDING POINT 5
27 88 88 88 88 C SIGNAL GAMMA BENDING POINT 6
28 B8 B8 B8 B8 C SIGNAL GAMMA BENDING POINT 7
29 DA DA DA DA C SIGNAL GAMMA BENDING POINT 8
2A 59 59 59 59 Cr(R-G) SIGNAL POSITIVE GAIN
2B 59 59 59 59 Cr(R-G) SIGNAL NEGATIVE GAIN
2C F2 F2 F2 F2 Cr(B-G) SIGNAL POSITIVE GAIN
2D F2 F2 F2 F2 Cr(B-G) SIGNAL NEGATIVE GAIN
2E D9 D9 D9 D9 Cb(R-G) SIGNAL POSITIVE GAIN
2F D9 D9 D9 D9 Cb(R-G) SIGNAL NEGATIVE GAIN
30 72 72 72 72 Cb(B-G) SIGNAL POSITIVE GAIN
31 72 72 72 72 Cb(B-G) SIGNAL NEGATIVE GAIN
32 38 38 38 38 INDOOR R-Y POSITIVE GAIN
33 38 38 38 38 INDOOR R-Y NEGATIVE GAIN
34 09 09 09 09 INDOOR R-Y POSITIVE GAIN
35 O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN
36 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN

Alignment and adjustment

5-6 Samsung Electronics

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
37 18 18 18 18 INDOOR B-Y NEGATIVE GAIN
38 18 18 18 18 INDOOR B-Y POSITIVE GAIN
39 01 01 01 01 INDOOR B-Y NEGATIVE GAIN
3A C8 C8 C8 C8 NEGA MODE W/B B CONTROL
3B 28 28 28 28 SPOT MODE AE TARGET
3C 35 35 35 35 R DETECT WINDOW H START POINT
3D 50 50 50 50 R DETECT WINDOW H STOP POINT
3E 3A 3A 3A 3A R DETECT WINDOW V START POINT
3F 4B 4B 4B 4B R DETECT WINDOW V STOP POINT
40 OO OO OO OO DSP ODM COMMEND
41 30 30 30 30 CLIP COUNTER THRESHOULD
42 7B 7B 7B 7B COLOR ADJUST START VALUE
43 85 85 85 85 R TARGET UP/DOWN OF D ZOOM
44 OO OO OO OO B TARGET UP/DOWN OF D ZOOM
45 FF FF FF FF SHUTTER OF D ZOOM
46 00 00 00 00 CCD DEFECT COMPENSATION FACTOR
47 F0 F0 F0 F0 ODM AE CLIP THRESHOULD VALUE
48 FF FF FF FF ODM Y UPPER VALUE OF AE MODE
49 OO OO OO OO ODM Y LOWER VALUE OF AE MODE
4A 3F 3F 3F 3F ODM Y UPPER VALUE OF AWB MODE
4B OO OO OO OO ODM Y LOWER VALUE OF AWB MODE
4C FF FF FF FF R-Y THRESHOULD VALUE OF AWB MODE
4D FF FF FF FF B-Y THRESHOULD VALUE OF AWB MODE
4E 3F 3F 3F 3F (R-Y)+(B-Y) THRESHOULD VALUE
4F 20 20 20 20 WHITE DETECTION THRESHOLD VALUE
50 OO OO OO OO DIGITAL CLAMP OPTICAL BLACK POINT
51 O2 O2 O2 O2 Y DELAY CONTROL SELECTION
52 A0 A0 A0 A0 Y SIGNAL GAIN
53 80 80 80 80 CHROMA GAIN CONTROL
54 83 83 83 83 Y SET-UP LEVEL CONTROL
55 AE AE AE AE WHITE CLIP CONTROL
56 2C 2C 2C 2C LUMINANCE BLANK LEVEL
57 EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL
58 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL
59 87 87 87 87 BURST FLAG DELAY SELECTION
5A OO OO OO OO FSC/2FSC CONTROL
5B OO OO OO OO DELAY CONTROL SELECTION
5C 3F 3F 3F 3F DELAY CONTROL SELECTION
5D 00 00 00 00 SCK CONTROL
5E 01 01 01 01 D/ZOOM MODE SELECTION
5F 02 O2 O2 O2 TG MODE SELECTION
60 OO OO OO OO INVERSE NUMBER OF V ZOOM RATIO
61 09 09 09 09 CCD V START POINT(INTEGER LINE)
62 OO OO OO OO CCD V START POINT(SUB PIXEL)
63 83 83 83 83 SHUTTER MODE
64 FF FF FF FF HIGH SHUTTER SPEED CONTROL
65 00 00 00 00 H1/H2/RG DELAY CONTROL
66 D9 D9 D9 D9 SHP/SHD DELAY CONTROL
67 OO OO OO OO SPO/FECKDELAY CONTROL
68 OO OO OO OO RG/SHP PULSE WIDTH ADJUSTMENT
69 80 80 80 80 D ZOOM MODE SELECTION
6A OO OO OO OO HORIZONTAL D ZOOM STEP
6B OO OO OO OO VERTICAL D ZOOM STEP
6C OO OO OO OO HORIZENTAL START READ ADDRESS -H
6D O1 O1 O1 O1 HORIZENTAL START READ ADDRESS -L
6E OO OO OO OO HORIZONTAL D ZOOM START SUB PIXEL
6F OO OO OO OO V D ZOOM START SUB PIXEL ODD FIELD
70 OO OO OO OO V D ZOOM START SUB PIXEL EVEN FIELD
71 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN
72 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN

Alignment and adjustment

Samsung Electronics 5-7

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
73 O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE
74 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE
75 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN
76 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN
77 18 18 18 18 OUTDOOR B-Y POSITIVE HUE
78 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE
79 48 48 48 48 R VALUE OF SEPIA MODE
7A 20 20 20 20 G VALUE OF SEPIA MODE
7B 78 78 78 78 R VALUE OF YELLOW MODE
7C 60 60 60 60 G VALUE OF YELLOW MODE
7D 88 88 88 88 HALL REFERENSE START VALUE
7E 20 20 20 20 HALL GAIN START VALUE
7F 4B 4B 4B 4B HALL MINIMUM VALUE (IRIS OPEN)
80 D7 D7 D7 D7 HALL MAXIMUM VALUE(IRIS CLOSE)
81 18 18 18 18 OUTDOOR DETECT IRIS CTL VALUE
82 30 30 30 30 AE TARGET (LOW BYTE)
83 O5 O5 O5 O5 AE TARGET (HIGH BYTE)
84 A0 A0 A0 A0 IRIS CONTROL MIN VALUE
85 3A 3A 3A 3A IRIS CONTROL MAX VALUE
86 02 02 02 02 TARGET MARGEIN OF IRIS ADJUSTMENT
87 12 12 12 12 CCD WHITE DEFFECTS ADJUSTMENT
88 85 85 85 85 AGC MAXIMUM CONTROL
89 10 10 10 10 NOT USED
8A 09 09 09 09 BLC ON AE TARGET
8B 48 48 48 48 CINEMA/SPOT LIGHT BLC TARGET
8C O8 O8 O8 O8 SAND/SNOW MODE AE TARGET
8D O8 O8 O8 O8 NEGA MODE AE TARGET
8E OA OA OA OA NOT USED
8F 84 84 84 84 WHITE BALANCE R TARGET
90 75 75 75 75 WHITE BALANCE B TARGET
91 45 45 45 45 R INDOOR START VALUE OF W/B ADJUST­MENT
92 85 85 85 85 B INDOOR START VALUE OF W/B ADJUST­MENT
93 65 65 65 65 R OUTDOOR START VALUE OF W/B ADJUST­MENT
94 68 68 68 68 R INDOOR START VALUE OF W/B ADJUST­MENT
95 3C 3C 3C 3C R INDOOR CONTROL VALUE
96 98 98 98 98 B INDOOR CONTROL VALUE
97 75 75 75 75 R OUTDOOR CONTROL VALUE
98 5C 5C 5C 5C B OUTDOOR CONTROL VALUE
99 O2 O2 O2 O2 R OUTDOOR CONTROL UP/DOWN MARGIN
9A 83 83 83 83 R INDOOR CONTROL UP/DOWN MARGIN
9B O3 O3 O3 O3 B INDOOR CONTROL UP/DOWN MARGIN
9C 8D 8D 8D 8D B OUTDOOR CONTROL UP/DOWN MARGIN
9D OO OO OO OO INITIAL(POWER ON) R CTL START DATA
9E OO OO OO OO INITIAL(POWER ON) B CTL START VALUE
9F 6E 6E 6E 6E W/B TABLE MODE
A0 O2 O2 O2 O2 W/B SD/3+AEAVR-MAXDETE
A1 90 90 90 90 W/B CONTROL BOUNDARY
A2 A6 A6 A6 A6 W/B CTL STOP HALL OF MACRO AREA
A3 48 48 48 48 W/B OUTDOOR STOP HALL
A4 00 00 00 00 R/B CTL SPEED UP/DOWN MODE
A5 48 48 48 48 CINEMA AE TAGET
A6 30 30 30 30 CINEMA / SPOT AE TAGET
A7 20 20 20 20 W/B STABLE CONDITION
A8 05 05 O5 O5 R CONTROL UP/DOWN OF D Z00M
A9 05 05 O5 O5 B CONTROL UP/DOWN OF D Z00M
AA 0E 0E 0E 0E FOCUS RESET POSITION L

Alignment and adjustment

5-8 Samsung Electronics

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
AB 11 11 11 11 FOCUS RESET POSITION H
AC 4B 4B 4B 4B ZOOM RESET POSITION L
AD 12 12 12 12 ZOOM RESET POSITION H
AE 83 83 83 83 ZOOM RESET DIFERRENCE
AF 40 40 40 40 AF FILTER1 DATA MAGNIFY RATO
B0 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA1
B1 OO OO OO OO FILTER1 NOISE LEVEL(H) OF AREA1
B2 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA2
B3 02 02 02 02 FILTER1 NOISE LEVEL(H) OF AREA2
B4 90 90 90 90 FILTER2 NOISE LEVEL(L) OF AREA1
B5 OO OO OO OO FILTER2 NOISE LEVEL(H) OF AREA1
B6 E0 E0 E0 E0 FILTER2 NOISE LEVEL(L) OF AREA2
B7 01 01 01 01 FILTER2 NOISE LEVEL(H) OF AREA2
B8 20 20 20 20 NOISE SLICE START AGC
B9 FE FE FE FE NOISE SLICE MAXIMUM VALUE
BA 30 30 30 30 CHROMA SUPRESS START AGC
BB O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE
BC 30 30 30 30 EY BLACK START AGC
BD O4 O4 O4 O4 EY BLACK MAXIMUM VALUE
BE A0 A0 A0 A0 AE TAGET OF NEGA MODE(FADE IN)
BF 77 77 77 77

H/V ADJUST OF D ZOOM HEADER COMMEND
C0 2A 2A 2A 2A FADE LIMIT OF NEGA MODE
C1 28 28 28 28 DATA CONTROL BOUNDARY OF OUTDOOR
C2 24 24 24 24 NEGA MODE W/B R-CONTROL DATA
C3 A1 A1 A1 A1 FOCUS RETURN LOW BYTE
C4 15 15 15 15 FOCUS RETURN HIGH BYTE
C5 A0 A0 A0 A0 ZOOM RETURN LOW BYTE
C6 12 12 12 12 ZOOM RETURN HIGH BYTE
C7 O5 O5 O5 O5 LENS CHECK MARGIN (WIDE)
C8 12 12 12 12 LENS CHECK MARGIN (TELE)
C9 65 65 65 65 ADJUST MODE IRIS SETTING DATA

CA 7F 7F BF BF D ZOOM RAITO
CB O6 O6 O6 O6 AE UP/DOWN OF NEGA MODE BLC
CC 00 00 00 00 SETUP ADJUST ENABLE
CD 70 70 70 70 HALL AUTO ADJUSTMENT
CE D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT
CF FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT
D0 FF FF FF FF LENS AUTO ADJUSTMENT
D1 FF FF FF FF HALL AUTO CHECK
D2 FF FF FF FF AGC AUTO CHECK
D3 FF FF FF FF LENS CHECK OF PCB LINE
D4 FF FF FF FF GYRO SENSOR CHECK (H)
D5 FF FF FF FF GYRO SENSOR CHECK (V)
D6 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT
D7 01 01 01 01 ZOOM/FOCUS CHECK ENABLE
D8 20 20 20 20 VR ZOOM CENTER MARGEIN
D9 00 00 00 00 COLOR GAIN ADJUSTMENT
DA 7E 7E 7E 7E SETUP AUTO ADJUSTMENT
DB O8 O8 O8 O8 HALL CHECK THRESHOULD
DC 82 82 82 82 COLOR ADJUST TARGET VALUE

DD 89 89 89 89 HALL ADJUST GAIN TARGET
DE 4D 4D 4D 4D HALL ADJUST CENTER
DF 00 00 00 00 NOT USED
E0 AA AA AA AA BK NOISE TH/GAIN OF EIS
E1 5F 5F 5F 5F H APPERTURE GAIN OF EIS
E2 FF FF FF FF #0C OF EIS ON
E3 07 07 07 07 #OD OF EIS ON
E4 A8 A8 A8 A8 #OE OF EIS ON
E5 10 10 10 10 #OF OF EIS ON
E6 OO OO OO OO #18 OF EIS ON

Alignment and adjustment

Samsung Electronics 5-9

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
E7 FF FF FF FF AGC CONTROL OF Y SINGNAL
E8 69 69 69 69 V GAIN-1(A/D GAIN)
E9 80 80 80 80 R TARGET OF W/B AUTO ADJUSTMENT
EA EB EB EB EB V GAIN-3(CENTERING GAIN)
EB 06 06 06 06 V STOP NOISE THRESHOULD
EC 8C 8C 8C 8C H GAIN-1(A/D GAIN)
ED 7F 7F 7F 7F B TARGET OF W/B AUTO ADJUSTMENT
EE EB EB EB EB H GAIN-3(CENTERING GAIN)
EF 09 09 09 09 H STOP NOISE THRESHOULD
F0 OO OO OO OO D-ZOOM STEP

6. Initial data of camera parts adjustment - CAMERA AF 2nd MICOM (UPD784035GC-828) DATA - NTSC

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
CD HALLA 70 70 70 70 HALL AUTO ADJUSTMENT
CE IRISRA D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT
CF WBA FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT
D0 LENSA FF FF FF FF LENS AUTO ADJUSTMENT
D6 Z.CHK 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT
O3 IRIS1 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE
O5 P.CLK 40 40 40 40 P.CLK ADJUSTMENT
O7 ADREF OO OO OO OO A/D REFERENCE CONTROL(SETUP)
O8 S.CLK 0F 0F 0F 0F SOFT CLIP CONTROL
O9 AGC1 18 18 18 18 AGC CONTROL
OB HAPER 58 58 58 58 HORIZONTAL APPERTURE GAIN
OC YSEL F8 F8 F8 F8 VERTICAL APPERTURE GAIN
1C CWBR 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL
1D CWBB 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL
32 CRGP 38 38 38 38 INDOOR R-Y POSITIVE GAIN
33 CRGN 38 38 38 38 INDOOR R-Y NEGATIVE GAIN
34 CHYE 09 09 09 09 INDOOR R-Y POSITIVE GAIN
35 CHB O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN
36 CBGP 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN
37 CBGN 18 18 18 18 INDOOR B-Y NEGATIVE GAIN
38 CHGR 18 18 18 18 INDOOR B-Y POSITIVE GAIN
39 PCBHN 01 01 01 01 INDOOR B-Y NEGATIVE GAIN
53 ECGAN 80 80 80 80 CHROMA GAIN CONTROL
54 ESY 83 83 83 83 Y SET-UP LEVEL CONTROL
55 EWC AE AE AE AE WHITE CLIP CONTROL
57 EUSC EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL
58 EVSC 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL
5D XKCON 00 00 00 00 SCK CONTROL
5E MDSEL 01 01 01 01 D/ZOOM MODE SELECTION
5F TGMSE 02 O2 O2 O2 TG MODE SELECTION
65 HRGDL 00 00 00 00 H1/H2/RG DELAY CONTROL
66 SHP.D D9 D9 D9 D9 SHP/SHD DELAY CONTROL
67 ADDL OO OO OO OO SPO/FECKDELAY CONTROL
71 ROUGP 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN
72 ROUGN 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN
73 CHOYE O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE
74 CHOB 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE
75 GOUGP 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN
76 BOUGN 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN
77 CHOGR 18 18 18 18 OUTDOOR B-Y POSITIVE HUE
78 CHOR 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE
82 AETAL 30 30 30 30 AE TARGET (LOW BYTE)
83 AETAH O5 O5 O5 O5 AE TARGET (HIGH BYTE)

Alignment and adjustment

5-10 Samsung Electronics

SC-L100 SC-L150

MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
88 AGCMA 85 85 85 85 AGC MAXIMUM CONTROL
8F WBTAR 84 84 84 84 WHITE BALANCE R TARGET
90 WBTAB 75 75 75 75 WHITE BALANCE B TARGET

95 R-IN 3C 3C 3C 3C R INDOOR CONTROL VALUE
96 B-IN 98 98 98 98 B INDOOR CONTROL VALUE
97 R-OUT 75 75 75 75 R OUTDOOR CONTROL VALUE
98 B-OUT 5C 5C 5C 5C B OUTDOOR CONTROL VALUE
B8 CFAPS 20 20 20 20 NOISE SLICE START AGC
B9 APNSC FE FE FE FE NOISE SLICE MAXIMUM VALUE
BB CFAOR O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE
BC BLKST 30 30 30 30 EY BLACK START AGC
BD BLKMX O4 O4 O4 O4 EY BLACK MAXIMUM VALUE
00 OO OO OO OO NOT USED
01 40 40 40 40 HALL GAIN
02 80 80 80 80 HALL REFERENCE
03 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE
04 OO OO OO OO IRIS LEVEL CONTROL-L
O5 40 40 40 40 P.CLK ADJUSTMENT
06 OO OO OO OO P.CLK PWM CONTROL-L
O7 OO OO OO OO A/D REFERENCE CONTROL(SETUP)
O8 0F 0F 0F 0F SOFT CLIP CONTROL
O9 18 18 18 18 AGC CONTROL
OA 66 66 66 66 H/V BLACK NOIS THRESHOLD/GAIN
OB 58 58 58 58 HORIZONTAL APPERTURE GAIN
OC F8 F8 F8 F8 VERTICAL APPERTURE GAIN
0D 0B 0B 0B 0B APERTURE SLICE CONTROL
OE A8 A8 A8 A8 Y HI-REF. VALUE FOR C SUPRESS
OF 10 10 10 10 EDGE REF. VALUE FOR C SUPRESS
10 05 05 05 05 Y SIGNAL GAMMA COEFF. 1
11 0A 0A 0A 0A Y SIGNAL GAMMA COEFF. 2
12 1C 1C 1C 1C Y SIGNAL GAMMA COEFF. 3
13 30 30 30 30 Y SIGNAL GAMMA COEFF. 4
14 4D 4D 4D 4D Y SIGNAL GAMMA COEFF. 5
15 76 76 76 76 Y SIGNAL GAMMA COEFF. 6
16 B8 B8 B8 B8 Y SIGNAL GAMMA COEFF. 7
17 DA DA DA DA Y SIGNAL GAMMA COEFF. 8
18 OO OO OO OO Y LPF SELECTION
19 11 11 11 11 Cr/Cb/Y LPF SELECTION
1A 42 42 42 42 C MATRIX COEF. OF Cr SIGNAL
1B 66 66 66 66 C MATRIX COEF. OF Cb SIGNAL
1C 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL
1D 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL
1E 24 24 24 24 C W/B COEF. OF G SIGNAL
1F 05 05 05 05 C DARK SLICE COEF. OF Cr SIG.
20 01 01 01 01 C DARK SLICE COEF. OF Cb SIG.
21 FB FB FB FB C DARK SLICE COEF. OF G SIG.
22 05 05 05 05 C SIGNAL GAMMA BENDING POINT 1
23 0D 0D 0D 0D C SIGNAL GAMMA BENDING POINT 2
24 1A 1A 1A 1A C SIGNAL GAMMA BENDING POINT 3
25 38 38 38 38 C SIGNAL GAMMA BENDING POINT 4
26 58 58 58 58 C SIGNAL GAMMA BENDING POINT 5
27 88 88 88 88 C SIGNAL GAMMA BENDING POINT 6
28 B8 B8 B8 B8 C SIGNAL GAMMA BENDING POINT 7
29 DA DA DA DA C SIGNAL GAMMA BENDING POINT 8
2A 59 59 59 59 Cr(R-G) SIGNAL POSITIVE GAIN
2B 59 59 59 59 Cr(R-G) SIGNAL NEGATIVE GAIN
2C F2 F2 F2 F2 Cr(B-G) SIGNAL POSITIVE GAIN
2D F2 F2 F2 F2 Cr(B-G) SIGNAL NEGATIVE GAIN
2E D9 D9 D9 D9 Cb(R-G) SIGNAL POSITIVE GAIN
2F D9 D9 D9 D9 Cb(R-G) SIGNAL NEGATIVE GAIN

Alignment and adjustment

Samsung Electronics 5-11

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
30 72 72 72 72 Cb(B-G) SIGNAL POSITIVE GAIN
31 72 72 72 72 Cb(B-G) SIGNAL NEGATIVE GAIN
32 38 38 38 38 INDOOR R-Y POSITIVE GAIN
33 38 38 38 38 INDOOR R-Y NEGATIVE GAIN
34 09 09 09 09 INDOOR R-Y POSITIVE GAIN
35 O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN
36 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN
37 18 18 18 18 INDOOR B-Y NEGATIVE GAIN
38 18 18 18 18 INDOOR B-Y POSITIVE GAIN
39 01 01 01 01 INDOOR B-Y NEGATIVE GAIN
3A C8 C8 C8 C8 NEGA MODE W/B B CONTROL
3B 28 28 28 28 SPOT MODE AE TARGET
3C 35 35 35 35 R DETECT WINDOW H START POINT
3D 50 50 50 50 R DETECT WINDOW H STOP POINT
3E 3A 3A 3A 3A R DETECT WINDOW V START POINT
3F 4B 4B 4B 4B R DETECT WINDOW V STOP POINT
40 OO OO OO OO DSP ODM COMMEND
41 30 30 30 30 CLIP COUNTER THRESHOULD
42 7B 7B 7B 7B COLOR ADJUST START VALUE
43 85 85 85 85 R TARGET UP/DOWN OF D ZOOM
44 OO OO OO OO B TARGET UP/DOWN OF D ZOOM
45 FF FF FF FF SHUTTER OF D ZOOM
46 00 00 00 00 CCD DEFECT COMPENSATION FACTOR
47 F0 F0 F0 F0 ODM AE CLIP THRESHOULD VALUE
48 FF FF FF FF ODM Y UPPER VALUE OF AE MODE
49 OO OO OO OO ODM Y LOWER VALUE OF AE MODE
4A 3F 3F 3F 3F ODM Y UPPER VALUE OF AWB MODE
4B OO OO OO OO ODM Y LOWER VALUE OF AWB MODE
4C FF FF FF FF R-Y THRESHOULD VALUE OF AWB MODE
4D FF FF FF FF B-Y THRESHOULD VALUE OF AWB MODE
4E 3F 3F 3F 3F (R-Y)+(B-Y) THRESHOULD VALUE
4F 01 01 01 01 WHITE DETECTION THRESHOLD VALUE
50 OO OO OO OO DIGITAL CLAMP OPTICAL BLACK POINT
51 O2 O2 O2 O2 Y DELAY CONTROL SELECTION
52 A0 A0 A0 A0 Y SIGNAL GAIN
53 80 80 80 80 CHROMA GAIN CONTROL
54 83 83 83 83 Y SET-UP LEVEL CONTROL
55 AE AE AE AE WHITE CLIP CONTROL
56 2C 2C 2C 2C LUMINANCE BLANK LEVEL
57 EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL
58 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL
59 87 87 87 87 BURST FLAG DELAY SELECTION
5A OO OO OO OO FSC/2FSC CONTROL
5B OO OO OO OO DELAY CONTROL SELECTION
5C 3F 3F 3F 3F DELAY CONTROL SELECTION
5D 00 00 00 00 SCK CONTROL
5E 01 01 01 01 D/ZOOM MODE SELECTION
5F 02 O2 O2 O2 TG MODE SELECTION
60 OO OO OO OO INVERSE NUMBER OF V ZOOM RATIO
61 09 09 09 09 CCD V START POINT(INTEGER LINE)
62 OO OO OO OO CCD V START POINT(SUB PIXEL)
63 83 83 83 83 SHUTTER MODE
64 FF FF FF FF HIGH SHUTTER SPEED CONTROL
65 00 00 00 00 H1/H2/RG DELAY CONTROL
66 D9 D9 D9 D9 SHP/SHD DELAY CONTROL
67 OO OO OO OO SPO/FECKDELAY CONTROL
68 OO OO OO OO RG/SHP PULSE WIDTH ADJUSTMENT
69 80 80 80 80 D ZOOM MODE SELECTION
6A OO OO OO OO HORIZONTAL D ZOOM STEP
6B OO OO OO OO VERTICAL D ZOOM STEP

Alignment and adjustment

5-12 Samsung Electronics

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
6C OO OO OO OO HORIZENTAL START READ ADDRESS -H
6D O1 O1 O1 O1 HORIZENTAL START READ ADDRESS -L
6E OO OO OO OO HORIZONTAL D ZOOM START SUB PIXEL
6F OO OO OO OO V D ZOOM START SUB PIXEL ODD FIELD
70 OO OO OO OO V D ZOOM START SUB PIXEL EVEN FIELD
71 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN

72 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN
73 O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE
74 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE
75 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN
76 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN
77 18 18 18 18 OUTDOOR B-Y POSITIVE HUE
78 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE
79 48 48 48 48 R VALUE OF SEPIA MODE
7A 20 20 20 20 G VALUE OF SEPIA MODE
7B 78 78 78 78 R VALUE OF YELLOW MODE
7C 60 60 60 60 G VALUE OF YELLOW MODE
7D 88 88 88 88 HALL REFERENSE START VALUE
7E 3A 3A 3A 3A HALL GAIN START VALUE
7F 4B 4B 4B 4B HALL MINIMUM VALUE (IRIS OPEN)
80 D7 D7 D7 D7 HALL MAXIMUM VALUE(IRIS CLOSE)
81 18 18 18 18 OUTDOOR DETECT IRIS CTL VALUE
82 30 30 30 30 AE TARGET (LOW BYTE)
83 O5 O5 O5 O5 AE TARGET (HIGH BYTE)
84 A0 A0 A0 A0 IRIS CONTROL MIN VALUE
85 3A 3A 3A 3A IRIS CONTROL MAX VALUE
86 02 02 02 02 TARGET MARGEIN OF IRIS ADJUSTMENT
87 12 12 12 12 CCD WHITE DEFFECTS ADJUSTMENT
88 85 85 85 85 AGC MAXIMUM CONTROL
89 10 10 10 10 NOT USED
8A 09 09 09 09 BLC ON AE TARGET
8B 48 48 48 48 CINEMA/SPOT LIGHT BLC TARGET
8C O8 O8 O8 O8 SAND/SNOW MODE AE TARGET
8D O8 O8 O8 O8 NEGA MODE AE TARGET
8E OA OA OA OA NOT USED
8F 88 88 88 88 WHITE BALANCE R TARGET
90 70 70 70 70 WHITE BALANCE B TARGET
91 45 45 45 45

R INDOOR START VALUE OF W/B ADJUSTMENT

92 85 85 85 85

B INDOOR START VALUE OF W/B ADJUSTMENT

93 65 65 65 65

R OUTDOOR START VALUE OF W/B ADJUSTMENT

94 68 68 68 68

R INDOOR START VALUE OF W/B ADJUSTMENT
95 3C 3C 3C 3C R INDOOR CONTROL VALUE
96 98 98 98 98 B INDOOR CONTROL VALUE
97 75 75 75 75 R OUTDOOR CONTROL VALUE
98 5C 5C 5C 5C B OUTDOOR CONTROL VALUE
99 O2 O2 O2 O2 R OUTDOOR CONTROL UP/DOWN MARGIN
9A 83 83 83 83 R INDOOR CONTROL UP/DOWN MARGIN
9B O3 O3 O3 O3 B INDOOR CONTROL UP/DOWN MARGIN

9C 8D 8D 8D 8D B OUTDOOR CONTROL UP/DOWN MARGIN
9D 88 88 88 88 INITIAL(POWER ON) R CTL START DATA
9E OO OO OO OO INITIAL(POWER ON) B CTL START VALUE
9F 6E 6E 6E 6E W/B TABLE MODE
A0 O2 O2 O2 O2 W/B SD/3+AEAVR-MAXDETE
A1 90 90 90 90 W/B CONTROL BOUNDARY
A2 A6 A6 A6 A6 W/B CTL STOP HALL OF MACRO AREA
A3 48 48 48 48 W/B OUTDOOR STOP HALL
A4 8A 8A 8A 8A

R OUTDOOR CONTROL UP/DOWN OF W/B ADJUST
A5 48 48 48 48 CINEMA AE TAGET
A6 30 30 30 30 CINEMA / SPOT AE TAGET
A7 20 20 20 20 W/B STABLE CONDITION

Alignment and adjustment

Samsung Electronics 5-13

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
A8 05 05 O5 O5 R CONTROL UP/DOWN OF D Z00M
A9 05 05 O5 O5 B CONTROL UP/DOWN OF D Z00M
AA 0E 0E 0E 0E FOCUS RESET POSITION L
AB 11 11 11 11 FOCUS RESET POSITION H
AC 4B 4B 4B 4B ZOOM RESET POSITION L
AD 12 12 12 12 ZOOM RESET POSITION H
AE 83 83 83 83 ZOOM RESET DIFERRENCE
AF 40 40 40 40 AF FILTER1 DATA MAGNIFY RATO
B0 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA1
B1 OO OO OO OO FILTER1 NOISE LEVEL(H) OF AREA1
B2 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA2
B3 02 02 02 02 FILTER1 NOISE LEVEL(H) OF AREA2
B4 90 90 90 90 FILTER2 NOISE LEVEL(L) OF AREA1
B5 OO OO OO OO FILTER2 NOISE LEVEL(H) OF AREA1
B6 E0 E0 E0 E0 FILTER2 NOISE LEVEL(L) OF AREA2
B7 01 01 01 01 FILTER2 NOISE LEVEL(H) OF AREA2
B8 20 20 20 20 NOISE SLICE START AGC
B9 FE FE FE FE NOISE SLICE MAXIMUM VALUE
BA 30 30 30 30 CHROMA SUPRESS START AGC
BB O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE
BC 30 30 30 30 EY BLACK START AGC
BD O4 O4 O4 O4 EY BLACK MAXIMUM VALUE
BE A0 A0 A0 A0 AE TAGET OF NEGA MODE(FADE IN)
BF 77 77 77 77

H/V ADJUST OF D ZOOM HEADER COMMEND
C0 2A 2A 2A 2A FADE LIMIT OF NEGA MODE
C1 28 28 28 28 DATA CONTROL BOUNDARY OF OUTDOOR
C2 24 24 24 24 NEGA MODE W/B R-CONTROL DATA
C3 A1 A1 A1 A1 FOCUS RETURN LOW BYTE
C4 15 15 15 15 FOCUS RETURN HIGH BYTE
C5 A0 A0 A0 A0 ZOOM RETURN LOW BYTE
C6 12 12 12 12 ZOOM RETURN HIGH BYTE
C7 O5 O5 O5 O5 LENS CHECK MARGIN (WIDE)
C8 12 12 12 12 LENS CHECK MARGIN (TELE)
C9 65 65 65 65 ADJUST MODE IRIS SETTING DATA
CA 7F 7F BF BF D ZOOM RAITO
CB O6 O6 O6 O6 AE UP/DOWN OF NEGA MODE BLC
CC 00 00 00 00 SETUP ADJUST ENABLE
CD 70 70 70 70 HALL AUTO ADJUSTMENT
CE D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT
CF FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT
D0 FF FF FF FF LENS AUTO ADJUSTMENT
D1 FF FF FF FF HALL AUTO CHECK
D2 FF FF FF FF AGC AUTO CHECK
D3 FF FF FF FF LENS CHECK OF PCB LINE
D4 FF FF FF FF GYRO SENSOR CHECK (H)
D5 FF FF FF FF GYRO SENSOR CHECK (V)
D6 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT
D7 01 01 01 01 ZOOM/FOCUS CHECK ENABLE
D8 20 20 20 20 VR ZOOM CENTER MARGEIN
D9 00 00 00 00 COLOR GAIN ADJUSTMENT
DA 7E 7E 7E 7E SETUP AUTO ADJUSTMENT
DB O8 O8 O8 O8 HALL CHECK THRESHOULD
DC 82 82 82 82 COLOR ADJUST TARGET VALUE
DD 89 89 89 89 HALL ADJUST GAIN TARGET
DE 4D 4D 4D 4D HALL ADJUST CENTER
DF 00 00 00 00 NOT USED
E0 AA AA AA AA BK NOISE TH/GAIN OF EIS
E1 5F 5F 5F 5F H APPERTURE GAIN OF EIS
E2 FF FF FF FF #0C OF EIS ON
E3 07 07 07 07 #OD OF EIS ON

Alignment and adjustment

5-14 Samsung Electronics

SC-L100 SC-L150
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
E4 A8 A8 A8 A8 #OE OF EIS ON
E5 10 10 10 10 #OF OF EIS ON
E6 OO OO OO OO #18 OF EIS ON

E7 80 80 80 80

B OUTDOOR CONTROL UP/DOWN OF W/B ADJUST
E8 69 69 69 69 V GAIN-1(A/D GAIN)
E9 80 80 80 80 R TARGET OF W/B AUTO ADJUSTMENT
EA EB EB EB EB V GAIN-3(CENTERING GAIN)
EB 06 06 06 06 V STOP NOISE THRESHOULD
EC 8C 8C 8C 8C H GAIN-1(A/D GAIN)

ED 7F 7F 7F 7F B TARGET OF W/B AUTO ADJUSTMENT
EE EB EB EB EB H GAIN-3(CENTERING GAIN)
EF 09 09 09 09 H STOP NOISE THRESHOULD
F0 OO OO OO OO D-ZOOM STEP
F1 O1 O1 O1 O1 NOT USED

7. Initial data of camera parts adjustment - CAMERA AF 1st MICOM (UPD784035GC-820) DATA - PAL

VP-L100 VP-L150

MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT

CD HALLA 70 70 70 70 HALL AUTO ADJUSTMENT
CE IRISRA D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT
CF WBA FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT
D0 LENSA FF FF FF FF LENS AUTO ADJUSTMENT
D6 Z.CHK 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT
O3 IRIS1 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE
O5 P.CLK 40 40 40 40 P.CLK ADJUSTMENT
O7 ADREF OO OO OO OO A/D REFERENCE CONTROL(SETUP)
O8 S.CLK 0F 0F 0F 0F SOFT CLIP CONTROL
O9 AGC1 18 18 18 18 AGC CONTROL
OB HAPER 5A 5A 5A 5A HORIZONTAL APPERTURE GAIN
OC YSEL FA FA FA FA VERTICAL APPERTURE GAIN
1C CWBR 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL
1D CWBB 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL

32 CRGP 47 47 47 47 INDOOR R-Y POSITIVE GAIN
33 CRGN 50 50 50 50 INDOOR R-Y NEGATIVE GAIN
34 CHYE 05 05 05 05 INDOOR R-Y POSITIVE GAIN
35 CHB O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN
36 CBGP 28 28 28 28 INDOOR B-Y POSITIVE GAIN
37 CBGN 20 20 20 20 INDOOR B-Y NEGATIVE GAIN
38 CHGR 20 20 20 20 INDOOR B-Y POSITIVE GAIN
39 PCBHN 0C 0C 0C 0C INDOOR B-Y NEGATIVE GAIN
53 ECGAN 88 88 88 88 CHROMA GAIN CONTROL
54 ESY 83 83 83 83 Y SET-UP LEVEL CONTROL
55 EWC D0 D0 D0 D0 WHITE CLIP CONTROL
57 EUSC ED ED ED ED B-Y SIGNAL BURST LEVEL CONTROL
58 EVSC 14 14 14 14 R-Y SIGNAL BURST LEVEL CONTROL

5D XKCON 04 04 04 04 SCK CONTROL

5E MDSEL 04 04 05 05 D/ZOOM MODE SELECTION
5F TGMSE 02 O2 O2 O2 TG MODE SELECTION
65 HRGDL 0E 0E 0E 0E H1/H2/RG DELAY CONTROL
66 SHP.D DC DC DC DC SHP/SHD DELAY CONTROL
67 ADDL OO OO OO OO SPO/FECKDELAY CONTROL
71 ROUGP 47 47 47 47 OUTDOOR R-Y POSITIVE GAIN
72 ROUGN 48 48 48 48 OUTDOOR R-Y NEGATIVE GAIN
73 CHOYE O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE
74 CHOB 15 15 15 15 OUTDOOR R-Y NEGATIVE HUE
75 GOUGP 2C 2C 2C 2C OUTDOOR B-Y POSITIVE GAIN
76 BOUGN 25 25 25 25 OUTDOOR B-Y NEGATIVE GAIN