SAMSUNG VP_L100 Service Manual

8mm CAMCORDER

VP-L100/VP-L150 SCL100/SCL150

SERVICE

1. Precautions

2. Reference Information

3. Product Specifications and Comparison Chart

4. Disassembly and Reassembly

5. Alignment and Adjustment

6. Exploded View and Parts List

7. Electrical Parts List

8. Block Diagrams

9. PCB Diagrams

10. Wiring Diagram

11. Schematic Diagrams

Manual

8mm CAMCORDER

CONTENTS

For mechanical disassembly and adjustment, refer to the “Mechanical Manual” (DE-6 AD68-30200A).

A

Samsung Electronics 1-1

1. Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including : control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people--particularly children

--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (See Fig. 1) : Warning : Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly the power outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including : antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed

0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

6. X-ray Limits : The picture tube is designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original.

Fig. 1 AC Leakage Test

7. Antenna Cold Check : With the unitÕs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

8. High Voltage Limit : High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits.

Heed the high voltage limits. These include the

X-ray protection Specifications Label, and the Product Safety and X-ray Warning Note on the

service data schematic.

9. Some semiconductor (Òsolid stateÓ) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

10. Immediately before handling any semiconductor

components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.)

Device Under

Test

(Reading should not be above

0.5mA) Leakage

Currant Tester

Earth Ground

Test all

exposed metal

surfaces

Also test with plug reversed (using AC adapter plug as required)

2-Wire Cord

Precautions

1-2 Samsung Electronics

11. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

12. Design Alteration Warning : Never alter or add to the mechanical or electrical design of this unit. Example : Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturerÕs warranty.

13. Hot Chassis Warning : Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following : Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

14. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

15. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

16. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last.

17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, outof-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

18. Picture Tube Implosion Warning : The picture tube in this receiver employs Òintegral implosionÓ protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

19. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some Òin-lineÓ picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such Òpermanently attachedÓ yokes from the picture tube.

20. Product Safety Notice : Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, ( or ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Samsung Electronics 3-1

3. Product Specifications and Comparison Chart

3-1 Product Specifications (SCL100 / SCL150)

Design and specifications are subject to change without notice.

Operation

Description

SYSTEM LCD Three-inch color TFT Liquid Crystal Display (LCD) screen Recording systems Video : Two rotary heads, helical FM scanning / Audio : FM stereo system Video signal NTSC color, EIA standard Cassette format 8 mm Tape speed SP mode (Standard Play) : approx. 14.345 mm/sec

Recording/Playback time SP mode (Standard Play) : 1 hour (P6-60)

Fast-forward/rewind time Approx. 3 minute 30 seconds (P6-60) Image device CCD (Charge Coupled Device)

Viewfinder Black and White electronic viewfinder Lens Combined 16X power zoom and (32X:SCL100, 64X:SCL150) digital zoom lens,

f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm.

Automatic focus system Inner Color temperature Auto Aperture correction Automatic with back light adjustment

OUTPUT CONNECTORS Video output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative Audio output Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms

GENERAL Power requirement AC power adapter (7.2V) ; battery pack (6.0V) Power consumption 6.5W (Camera Recording, LCD on) Tripod attachment thread Attachment screw less than 6mm long Microphone Electric condensor microphone, omni-directional, monaural type Temperature range Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F) Dimensions/weight Approx. 213 X 116 X 107 mm (L X H X W); Approx. 1000 g

Excluding battery pack and cassette.

Product Specifications

3-2 Samsung Electronics

3-2 Product Specifications (VP-L100 / VP-L150)

Design and specifications are subject to change without notice.

Operation

Description

SYSTEM LCD Three-inch colour TFT Liquid Crystal Display (LCD) screen Recording systems Video : Two rotary heads, helical FM scanning / Audio : FM stereo system Video signal PAL colour, CCIR standard Cassette format 8 mm Tape speed SP mode (Standard Play) : approx. 20.051 mm/sec

Recording/Playback time SP mode (Standard Play) : 1 hour (P5-60)

Fast-forward/rewind time Approx. 4 minute (P5-60) Image device CCD (Charge Coupled Device)

Viewfinder Black and White electronic viewfinder Lens Combined 16X power zoom and 32X(VP-L150) digital zoom lens,

f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm.

Automatic focus system Inner Colour temperature Auto Aperture correction Automatic with back light adjustment

OUTPUT CONNECTORS Video output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative Audio output Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms

GENERAL Power requirement AC power adapter (7.2V) ; battery pack (6.0V) Power consumption 6.5W (Camera Recording, LCD on) Tripod attachment thread Attachment screw less than 6mm long Microphone Electric condensor microphone, omni-directional, monaural type Temperature range Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F) Dimensions/weight Approx. 213 X 116 X 107 mm (L X H X W); Approx. 1000 g

Excluding battery pack and cassette.

Product Specifications

Samsung Electronics 3-3

3-3 Comparison Chart

VIEWFINDER EVF EVF EVF EVF D.ZOOM X16 X32 D.ZOOM X32 D.ZOOM X64 D.ZOOM VIDEO NORMAL NORMAL NORMAL NORMAL STEREO X X X X EIS X O X O LCD 3 inch 3 inch 3 inch 3 inch

MODEL

FUNCTION

VP-L100 VP-L150 SCL100 SCL150

Product Specifications

3-4 Samsung Electronics

MEMO

Samsung Electronics 4-1

4. Disassembly and Reassembly

4-1 Cabinet and PCB

4-1-1 Ass’y Cover-Housing removal

Œ APPLY POWER AND EJECT THE COVER HOUSING.

´ REMOVE 2 SCREWS.

ˇ REMOVE THE ASS'Y COVER-HOUSING IN

THE DIRECTION OF ARROW.

Fig. 4-1 Ass’y Cover-Housing removal

Disassembly and Reassembly

4-2 Samsung Electronics

4-1-2 Ass’y Case-Top removal

"B"

2 LOCKING TABS

PRECISION SCREW DRIVER

< DETAIL "A" >

< DETAIL "B" >

Œ REMOVE THE ASS'Y-CASE-TOP BY GENTLY RELEASING 2 LOCKING TABS WITH A PRECISION SCREW DRIVER. (SEE DETAIL "A")

• NOTE : CLOSE THE HOUSING ASS'Y AFTER DISASSEMBLING.

• REASSEMBLY : PUT THE 7 TABS INTO THE SLOT WHILE SLIDING IT AS SHOWN IN DETAIL "B".

Fig. 4-2 Ass’y Case-Top removal

Disassembly and Reassembly

Samsung Electronics 4-3

4-1-3 Ass’y Front removal

Œ REMOVE 2 SCREWS.

´ REMOVE 2 SCREWS.

¨ REMOVE THE ASS'Y-FRONT IN THE DIRECTION OF ARROW.

ˆ DISCONNECT 2 CONNECTORS FROM THE

CN891,CN893 OF AUDIO PCB.

ˇ REMOVE 1 SCREW.

Fig. 4-3 Ass’y Front removal

Disassembly and Reassembly

4-4 Samsung Electronics

4-1-4 Ass’y Case-Right removal

¨ REMOVE THE ASS'Y CASE-RIGHT IN THE DIRECTION OF ARROW "B".

ˇ SLIDE THE ZOOM SWITCH IN

THE DIRECTION OF ARROW "A".

Œ REMOVE 1 SCREW.

´ REMOVE 2 SCREWS.

Fig. 4-4 Ass’y Case-Rignt removal

Disassembly and Reassembly

Samsung Electronics 4-5

4-1-5 Ass’y Case-Left removal

¨ REMOVE 2 SCREWS.

ˆ REMOVE THE ASS'Y CASE-LEFT IN THE DIRECTION OF ARROW.

∏ DISCONNECT THE CONNECTER FROM THE CN502 OF MAIN PCB.

ˇ REMOVE 1 SCREW.

´ REMOVE 3 SCREWS.

Œ REMOVE 1 SCREW.

Fig. 4-5 Ass’y Case-Left removal

Disassembly and Reassembly

4-6 Samsung Electronics

4-1-6 Ass’y Case-Battery removal

´ DISCONNECT THE CN961 OF THE REAR PCB FROM THE CN501 OF MAIN PCB AND THEN REMOVE THE ASS'Y CASE-BATTERY IN THE DIRECTION OF ARROW.

Œ REMOVE 1 SCREW.

Fig. 4-6 Ass’y Case-Battery removal

Disassembly and Reassembly

Samsung Electronics 4-7

4-1-7 Ass’y Case-Bottom removal

Fig. 4-7 Ass’y Case-Bottom removal

´ REMOVE THE CASE- BOTTOM IN THE DIRECTION OF ARROW.

Œ REMOVE 2 SCREWS.

Disassembly and Reassembly

4-8 Samsung Electronics

4-1-8 Ass’y-Deck removal

¨ REMOVE 1 SCREW.

ˇ REMOVE 2 SCREWS.

ˆ DISCONNECT THE FPC FROM THE ASS'Y DECK.

Ø DISCONNECT THE FPC FROM

THE CN501 OF MAIN PCB.

∏ REMOVE THE ASS'Y DECK IN THE DIRECTION OF ARROW .

Fig. 4-8 Audio PCB and Ass’y-Deck removal

Disassembly and Reassembly

Samsung Electronics 4-9

4-1-9 Ass’y Camera and Main PCB removal

CNC01

CNP01

Œ DESOLDER

ˇ DISCONNECT THE CNC01 FROM THE CNP01 OF MAIN PCB

AND THEN REMOVE THE ASS'Y CAMERA IN THE DIRECTION OF ARROW.

SOLDERING POINT

´ REMOVE 2 SCREWS.

Fig. 4-9 Ass’y Camera and Main PCB removal

Disassembly and Reassembly

4-10 Samsung Electronics

4-1-10 Ass’y LCD removal

"A"

Œ REMOVE 5 SCREWS.

´ REMOVE THE ASS'Y LCD IN THE DIRECTION OF ARROW "A".

Fig. 4-10 Ass’y LCD removal

Disassembly and Reassembly

Samsung Electronics 4-11

4-1-11 Ass’y EVF removal

¨ REMOVE THE ASS'Y EVF IN THE DIRECTION OF ARROW "B".

Œ DISCONNECT THE LEAD CONNECTOR FROM

THE CN803 OF FUNCTION MENU PCB.

´ REMOVE 1 SCREW.

ˇ REMOVE 3 SCREWS.

Fig. 4-11Ass’y EVF removal

Disassembly and Reassembly

4-12 Samsung Electronics

4-2 Circuit Boards Location

Fig. 4-12 Circuit Boards Location

NO. CONNECTOR DIRECTION CONNECTOR NO.

LOCA-NO. LOCA-NO. 2 CN101 MAIN PCB DECK -- 1 4 CN503 MAIN PCB DECK -- 3 7 CN501 MAIN PCB REAR CN961 8

19 CN892 MIC CPB MIC -- 18 11 CN851 MAIN PCB MIC PCB CN891 12

9 CNP03 MAIN PCB MIC PCB CN893 10

16 CNL201 LCD PCB MAIN PCB CN702 15 25 CNL301 LCD PCB LCD -- -26 CNL102 LCD PCB B/LIGHT -- --

-- CNE02 EVF MANU PCB CN803 24

21 CN805 FUNC MENU CN802 20 22 CN806 AE MENU CN802 20 14 CN801 MENU MAIN CN502 13 23 CN804 MENU SPEAKER -- -17 CNP02 MAIN PCB LENS -- --

5 CNP01 MAIN PCB CCD PCB CNC01 6

Disassembly and Reassembly

Samsung Electronics 4-13

4-3 Connector Diagram

FRONT PCB

Fig. 4-13 Connector Diagram

Fig. 4-14

Disassembly and Reassembly

4-14 Samsung Electronics

MEMO

Samsung Electronics 5-1

5. Alignment and Adjustment

5-1 Mechanical Adjustment

Test Point :

PB RF - Pin 45 of IC201 Head Switching Trigger - Pin 96 of IC601

Fig. 1 The location of test point

(PIN 45)

(PIN 96)

(PIN 67)

* Note 1 : Mechanical alignment is performed for the linearity of PB-RF(Envelope). * Note 2 : Refer to the mechanism manual ÒDE-6Ó(AD68-30200A) for the mechanism alignment.

1) Short between pin #67 of IC601 and GND in order to set the TEST MODE.(ThatÕs Track Shift Mode)

2) Connect the Head SW Pulse in CH1 and the PB-RF in CH2 to oscilloscope.

3) Refer to the Fig1 for the location of test point.

4) Play the alignment tape supplied, and fit the PB-RF form like as Fig1. (Refer to the alignment manual of the DE-6 described above).

5) If the alignment is completed, then remove the short wire for the release of the test mode.

Alignment and adjustment

5-2 Samsung Electronics

5-2 Camera Section Adjustment

Note :

1. This system has

1) EEPROM to store the confirmed adjustment data.

2) DSP (Digital Signal Process ; ICP04 - Main board) chip to process the signal of camera parts.

3) One test point for the frequency adjustment of DSP main clock (P. CLK).

2. Keep in mind

1) Readjustment is needed when the EEPROM (ICP10 of Main board) is replaced. The reason is that EEPROM stores confirmed adjustment value of each adjustment step.

5-2-1 Preparations

1. Equipments to be used

1) DC Power supply

2) Oscilloscope

3) Frequency counter

4) Vectorscope

5) Waveform monitor

6) Color monitor or TV

7) Various charts

- Color bar chart

- Gray-scale chart, etc...

8) Alignment tape (Lion pattern)

2. Composition of camera P.C.Boards

1) Main PCB 2) CCD PCB

3) EVF PCB 4) LCD PCB

3. Adjustment preparations

1) Press the confirm button when each manual adjustment step is completed to write the adjustment data to the EEPROM.

2) After each adjustment step is completed, OSD shows ÒOK!Ó.

3) To cancel the adjustment mode, remove the power source.

4. Menu Board

The following is a chart explaining the use of each button :

Using Button

TITLE (CONFIRM) C.RESET (DATA DOWN) DISPLAY (DATA UP) MENU (MODE UP) DATE (MODE DOWN) FADE (FAR ) BLC (NEAR)

Adjustment

Data store after finishing adjustment by DATA UP/DOWN button. When changing data value of adjust state.

Mode change.

Focus adjustment.

Alignment and adjustment

Samsung Electronics 5-3

The function buttons on the Menu Board are used to control the camcorder additionally,

These buttons should be used for adjustment of the camera section.

Menu Board for camcorder adjustment

Figure of button placement when Menu Board is

used for service adjustment.

Reassignment

in the

adjustment mode

Note : In service adjustment mode, button names are different from those in customer camera function control

mode. EX) TITLE button is the same as confirm.

5. How to get into service ÒADJUSTÓ mode

1. Connect the power source (battery/ DC cable).

2. Eject the tape if it is in the unit.

3. Set the power switch of the camcorder to ÒCAMERAÓ position.

4. Set OSD on state.

STEP 1

1. PRESS ÒDSEÓ Button 3 times on the camcorder.

2. It goes to into ÒNEGAÓ mode.

3. Press and hold the ÒEJECTÓ button and ÒDISPLAYÓ button on the camcorder at the same time for more than 3 seconds. Then unit goes into service mode.

STEP 2

On screen display show “CD HALLA XX XX” CAMERA ADJUSTMENT mode has successfully been activated.

STEP 3

NEGA

OSD

Note : When ÒXX XXÓ is shown in service adjustment precedures, this indicates variable values.

Alignment and adjustment

5-4 Samsung Electronics

5. Initial data of camera parts adjustment - CAMERA AF 1st MICOM (UPD784035GC-820) DATA - NTSC

During camera adjustment, the OSD displays the following abbreviations to indicate the selected mode.

Note : ÒData 1Ó is previous setting in memory, ÒData 2Ó is

now adjustment setting, that changes during adjustment mode. After pressing ÒTITLE (Confirm)Ó, it goes to memory.

Example) “ 00 XXXX XX XX “

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT CD HALLA 70 70 70 70 HALL AUTO ADJUSTMENT CE IRISRA D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT CF WBA FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT D0 LENSA FF FF FF FF LENS AUTO ADJUSTMENT D6 Z.CHK 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT O3 IRIS1 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE O5 P.CLK 40 40 40 40 P.CLK ADJUSTMENT O7 ADREF OO OO OO OO A/D REFERENCE CONTROL(SETUP) O8 S.CLK 0F 0F 0F 0F SOFT CLIP CONTROL O9 AGC1 18 18 18 18 AGC CONTROL OB HAPER 58 58 58 58 HORIZONTAL APPERTURE GAIN OC YSEL F8 F8 F8 F8 VERTICAL APPERTURE GAIN 1C CWBR 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL 1D CWBB 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL 32 CRGP 38 38 38 38 INDOOR R-Y POSITIVE GAIN 33 CRGN 38 38 38 38 INDOOR R-Y NEGATIVE GAIN 34 CHYE 09 09 09 09 INDOOR R-Y POSITIVE GAIN 35 CHB O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN 36 CBGP 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN 37 CBGN 18 18 18 18 INDOOR B-Y NEGATIVE GAIN 38 CHGR 18 18 18 18 INDOOR B-Y POSITIVE GAIN 39 PCBHN 01 01 01 01 INDOOR B-Y NEGATIVE GAIN 53 ECGAN 80 80 80 80 CHROMA GAIN CONTROL 54 ESY 83 83 83 83 Y SET-UP LEVEL CONTROL 55 EWC AE AE AE AE WHITE CLIP CONTROL 57 EUSC EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL 58 EVSC 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL 5D XKCON 00 00 00 00 SCK CONTROL 5E MDSEL 01 01 01 01 D/ZOOM MODE SELECTION 5F TGMSE 02 O2 O2 O2 TG MODE SELECTION 65 HRGDL 00 00 00 00 H1/H2/RG DELAY CONTROL 66 SHP.D D9 D9 D9 D9 SHP/SHD DELAY CONTROL 67 ADDL OO OO OO OO SPO/FECKDELAY CONTROL 71 ROUGP 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN 72 ROUGN 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN 73 CHOYE O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE 74 CHOB 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE 75 GOUGP 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN 76 BOUGN 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN 77 CHOGR 18 18 18 18 OUTDOOR B-Y POSITIVE HUE 78 CHOR 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE 82 AETAL 30 30 30 30 AE TARGET (LOW BYTE) 83 AETAH O5 O5 O5 O5 AE TARGET (HIGH BYTE) 88 AGCMA 85 85 85 85 AGC MAXIMUM CONTROL 8F WBTAR 84 84 84 84 WHITE BALANCE R TARGET 90 WBTAB 75 75 75 75 WHITE BALANCE B TARGET 95 R-IN 3C 3C 3C 3C R INDOOR CONTROL VALUE 96 B-IN 98 98 98 98 B INDOOR CONTROL VALUE 97 R-OUT 75 75 75 75 R OUTDOOR CONTROL VALUE

Alignment and adjustment

Samsung Electronics 5-5

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT 98 B-OUT 5C 5C 5C 5C B OUTDOOR CONTROL VALUE B8 CFAPS 20 20 20 20 NOISE SLICE START AGC B9 APNSC FE FE FE FE NOISE SLICE MAXIMUM VALUE BB CFAOR O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE BC BLKST 30 30 30 30 EY BLACK START AGC BD BLKMX O4 O4 O4 O4 EY BLACK MAXIMUM VALUE 00 OO OO OO OO NOT USED 01 40 40 40 40 HALL GAIN 02 80 80 80 80 HALL REFERENCE 03 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE 04 OO OO OO OO IRIS LEVEL CONTROL-L O5 40 40 40 40 P.CLK ADJUSTMENT 06 OO OO OO OO P.CLK PWM CONTROL-L O7 OO OO OO OO A/D REFERENCE CONTROL(SETUP) O8 0F 0F 0F 0F SOFT CLIP CONTROL O9 18 18 18 18 AGC CONTROL OA 66 66 66 66 H/V BLACK NOIS THRESHOLD/GAIN OB 58 58 58 58 HORIZONTAL APPERTURE GAIN OC F8 F8 F8 F8 VERTICAL APPERTURE GAIN 0D 0B 0B 0B 0B APERTURE SLICE CONTROL OE A8 A8 A8 A8 Y HI-REF. VALUE FOR C SUPRESS OF 10 10 10 10 EDGE REF. VALUE FOR C SUPRESS 10 05 05 05 05 Y SIGNAL GAMMA COEFF. 1 11 0A 0A 0A 0A Y SIGNAL GAMMA COEFF. 2 12 1C 1C 1C 1C Y SIGNAL GAMMA COEFF. 3 13 30 30 30 30 Y SIGNAL GAMMA COEFF. 4 14 4D 4D 4D 4D Y SIGNAL GAMMA COEFF. 5 15 76 76 76 76 Y SIGNAL GAMMA COEFF. 6 16 B8 B8 B8 B8 Y SIGNAL GAMMA COEFF. 7 17 DA DA DA DA Y SIGNAL GAMMA COEFF. 8 18 OO OO OO OO Y LPF SELECTION 19 11 11 11 11 Cr/Cb/Y LPF SELECTION 1A 42 42 42 42 C MATRIX COEF. OF Cr SIGNAL 1B 66 66 66 66 C MATRIX COEF. OF Cb SIGNAL 1C 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL 1D 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL 1E 24 24 24 24 C W/B COEF. OF G SIGNAL 1F 05 05 05 05 C DARK SLICE COEF. OF Cr SIG. 20 01 01 01 01 C DARK SLICE COEF. OF Cb SIG. 21 FB FB FB FB C DARK SLICE COEF. OF G SIG. 22 05 05 05 05 C SIGNAL GAMMA BENDING POINT 1 23 0D 0D 0D 0D C SIGNAL GAMMA BENDING POINT 2 24 1A 1A 1A 1A C SIGNAL GAMMA BENDING POINT 3 25 38 38 38 38 C SIGNAL GAMMA BENDING POINT 4 26 58 58 58 58 C SIGNAL GAMMA BENDING POINT 5 27 88 88 88 88 C SIGNAL GAMMA BENDING POINT 6 28 B8 B8 B8 B8 C SIGNAL GAMMA BENDING POINT 7 29 DA DA DA DA C SIGNAL GAMMA BENDING POINT 8 2A 59 59 59 59 Cr(R-G) SIGNAL POSITIVE GAIN 2B 59 59 59 59 Cr(R-G) SIGNAL NEGATIVE GAIN 2C F2 F2 F2 F2 Cr(B-G) SIGNAL POSITIVE GAIN 2D F2 F2 F2 F2 Cr(B-G) SIGNAL NEGATIVE GAIN 2E D9 D9 D9 D9 Cb(R-G) SIGNAL POSITIVE GAIN 2F D9 D9 D9 D9 Cb(R-G) SIGNAL NEGATIVE GAIN 30 72 72 72 72 Cb(B-G) SIGNAL POSITIVE GAIN 31 72 72 72 72 Cb(B-G) SIGNAL NEGATIVE GAIN 32 38 38 38 38 INDOOR R-Y POSITIVE GAIN 33 38 38 38 38 INDOOR R-Y NEGATIVE GAIN 34 09 09 09 09 INDOOR R-Y POSITIVE GAIN 35 O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN 36 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN

Alignment and adjustment

5-6 Samsung Electronics

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT 37 18 18 18 18 INDOOR B-Y NEGATIVE GAIN 38 18 18 18 18 INDOOR B-Y POSITIVE GAIN 39 01 01 01 01 INDOOR B-Y NEGATIVE GAIN 3A C8 C8 C8 C8 NEGA MODE W/B B CONTROL 3B 28 28 28 28 SPOT MODE AE TARGET 3C 35 35 35 35 R DETECT WINDOW H START POINT 3D 50 50 50 50 R DETECT WINDOW H STOP POINT 3E 3A 3A 3A 3A R DETECT WINDOW V START POINT 3F 4B 4B 4B 4B R DETECT WINDOW V STOP POINT 40 OO OO OO OO DSP ODM COMMEND 41 30 30 30 30 CLIP COUNTER THRESHOULD 42 7B 7B 7B 7B COLOR ADJUST START VALUE 43 85 85 85 85 R TARGET UP/DOWN OF D ZOOM 44 OO OO OO OO B TARGET UP/DOWN OF D ZOOM 45 FF FF FF FF SHUTTER OF D ZOOM 46 00 00 00 00 CCD DEFECT COMPENSATION FACTOR 47 F0 F0 F0 F0 ODM AE CLIP THRESHOULD VALUE 48 FF FF FF FF ODM Y UPPER VALUE OF AE MODE 49 OO OO OO OO ODM Y LOWER VALUE OF AE MODE 4A 3F 3F 3F 3F ODM Y UPPER VALUE OF AWB MODE 4B OO OO OO OO ODM Y LOWER VALUE OF AWB MODE 4C FF FF FF FF R-Y THRESHOULD VALUE OF AWB MODE 4D FF FF FF FF B-Y THRESHOULD VALUE OF AWB MODE 4E 3F 3F 3F 3F (R-Y)+(B-Y) THRESHOULD VALUE 4F 20 20 20 20 WHITE DETECTION THRESHOLD VALUE 50 OO OO OO OO DIGITAL CLAMP OPTICAL BLACK POINT 51 O2 O2 O2 O2 Y DELAY CONTROL SELECTION 52 A0 A0 A0 A0 Y SIGNAL GAIN 53 80 80 80 80 CHROMA GAIN CONTROL 54 83 83 83 83 Y SET-UP LEVEL CONTROL 55 AE AE AE AE WHITE CLIP CONTROL 56 2C 2C 2C 2C LUMINANCE BLANK LEVEL 57 EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL 58 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL 59 87 87 87 87 BURST FLAG DELAY SELECTION 5A OO OO OO OO FSC/2FSC CONTROL 5B OO OO OO OO DELAY CONTROL SELECTION 5C 3F 3F 3F 3F DELAY CONTROL SELECTION 5D 00 00 00 00 SCK CONTROL 5E 01 01 01 01 D/ZOOM MODE SELECTION 5F 02 O2 O2 O2 TG MODE SELECTION 60 OO OO OO OO INVERSE NUMBER OF V ZOOM RATIO 61 09 09 09 09 CCD V START POINT(INTEGER LINE) 62 OO OO OO OO CCD V START POINT(SUB PIXEL) 63 83 83 83 83 SHUTTER MODE 64 FF FF FF FF HIGH SHUTTER SPEED CONTROL 65 00 00 00 00 H1/H2/RG DELAY CONTROL 66 D9 D9 D9 D9 SHP/SHD DELAY CONTROL 67 OO OO OO OO SPO/FECKDELAY CONTROL 68 OO OO OO OO RG/SHP PULSE WIDTH ADJUSTMENT 69 80 80 80 80 D ZOOM MODE SELECTION 6A OO OO OO OO HORIZONTAL D ZOOM STEP 6B OO OO OO OO VERTICAL D ZOOM STEP 6C OO OO OO OO HORIZENTAL START READ ADDRESS -H 6D O1 O1 O1 O1 HORIZENTAL START READ ADDRESS -L 6E OO OO OO OO HORIZONTAL D ZOOM START SUB PIXEL 6F OO OO OO OO V D ZOOM START SUB PIXEL ODD FIELD 70 OO OO OO OO V D ZOOM START SUB PIXEL EVEN FIELD 71 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN 72 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN

Alignment and adjustment

Samsung Electronics 5-7

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT 73 O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE 74 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE 75 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN 76 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN 77 18 18 18 18 OUTDOOR B-Y POSITIVE HUE 78 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE 79 48 48 48 48 R VALUE OF SEPIA MODE 7A 20 20 20 20 G VALUE OF SEPIA MODE 7B 78 78 78 78 R VALUE OF YELLOW MODE 7C 60 60 60 60 G VALUE OF YELLOW MODE 7D 88 88 88 88 HALL REFERENSE START VALUE 7E 20 20 20 20 HALL GAIN START VALUE 7F 4B 4B 4B 4B HALL MINIMUM VALUE (IRIS OPEN) 80 D7 D7 D7 D7 HALL MAXIMUM VALUE(IRIS CLOSE) 81 18 18 18 18 OUTDOOR DETECT IRIS CTL VALUE 82 30 30 30 30 AE TARGET (LOW BYTE) 83 O5 O5 O5 O5 AE TARGET (HIGH BYTE) 84 A0 A0 A0 A0 IRIS CONTROL MIN VALUE 85 3A 3A 3A 3A IRIS CONTROL MAX VALUE 86 02 02 02 02 TARGET MARGEIN OF IRIS ADJUSTMENT 87 12 12 12 12 CCD WHITE DEFFECTS ADJUSTMENT 88 85 85 85 85 AGC MAXIMUM CONTROL 89 10 10 10 10 NOT USED 8A 09 09 09 09 BLC ON AE TARGET 8B 48 48 48 48 CINEMA/SPOT LIGHT BLC TARGET 8C O8 O8 O8 O8 SAND/SNOW MODE AE TARGET 8D O8 O8 O8 O8 NEGA MODE AE TARGET 8E OA OA OA OA NOT USED 8F 84 84 84 84 WHITE BALANCE R TARGET 90 75 75 75 75 WHITE BALANCE B TARGET 91 45 45 45 45 R INDOOR START VALUE OF W/B ADJUSTMENT 92 85 85 85 85 B INDOOR START VALUE OF W/B ADJUSTMENT 93 65 65 65 65 R OUTDOOR START VALUE OF W/B ADJUSTMENT 94 68 68 68 68 R INDOOR START VALUE OF W/B ADJUSTMENT 95 3C 3C 3C 3C R INDOOR CONTROL VALUE 96 98 98 98 98 B INDOOR CONTROL VALUE 97 75 75 75 75 R OUTDOOR CONTROL VALUE 98 5C 5C 5C 5C B OUTDOOR CONTROL VALUE 99 O2 O2 O2 O2 R OUTDOOR CONTROL UP/DOWN MARGIN 9A 83 83 83 83 R INDOOR CONTROL UP/DOWN MARGIN 9B O3 O3 O3 O3 B INDOOR CONTROL UP/DOWN MARGIN 9C 8D 8D 8D 8D B OUTDOOR CONTROL UP/DOWN MARGIN 9D OO OO OO OO INITIAL(POWER ON) R CTL START DATA 9E OO OO OO OO INITIAL(POWER ON) B CTL START VALUE 9F 6E 6E 6E 6E W/B TABLE MODE A0 O2 O2 O2 O2 W/B SD/3+AEAVR-MAXDETE A1 90 90 90 90 W/B CONTROL BOUNDARY A2 A6 A6 A6 A6 W/B CTL STOP HALL OF MACRO AREA A3 48 48 48 48 W/B OUTDOOR STOP HALL A4 00 00 00 00 R/B CTL SPEED UP/DOWN MODE A5 48 48 48 48 CINEMA AE TAGET A6 30 30 30 30 CINEMA / SPOT AE TAGET A7 20 20 20 20 W/B STABLE CONDITION A8 05 05 O5 O5 R CONTROL UP/DOWN OF D Z00M A9 05 05 O5 O5 B CONTROL UP/DOWN OF D Z00M AA 0E 0E 0E 0E FOCUS RESET POSITION L

Alignment and adjustment

5-8 Samsung Electronics

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT AB 11 11 11 11 FOCUS RESET POSITION H AC 4B 4B 4B 4B ZOOM RESET POSITION L AD 12 12 12 12 ZOOM RESET POSITION H AE 83 83 83 83 ZOOM RESET DIFERRENCE AF 40 40 40 40 AF FILTER1 DATA MAGNIFY RATO B0 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA1 B1 OO OO OO OO FILTER1 NOISE LEVEL(H) OF AREA1 B2 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA2 B3 02 02 02 02 FILTER1 NOISE LEVEL(H) OF AREA2 B4 90 90 90 90 FILTER2 NOISE LEVEL(L) OF AREA1 B5 OO OO OO OO FILTER2 NOISE LEVEL(H) OF AREA1 B6 E0 E0 E0 E0 FILTER2 NOISE LEVEL(L) OF AREA2 B7 01 01 01 01 FILTER2 NOISE LEVEL(H) OF AREA2 B8 20 20 20 20 NOISE SLICE START AGC B9 FE FE FE FE NOISE SLICE MAXIMUM VALUE BA 30 30 30 30 CHROMA SUPRESS START AGC BB O3 O3 O3 O3 CHROMA SUPRESS MAXIMUM VALUE BC 30 30 30 30 EY BLACK START AGC BD O4 O4 O4 O4 EY BLACK MAXIMUM VALUE BE A0 A0 A0 A0 AE TAGET OF NEGA MODE(FADE IN) BF 77 77 77 77

H/V ADJUST OF D ZOOM HEADER COMMEND C0 2A 2A 2A 2A FADE LIMIT OF NEGA MODE C1 28 28 28 28 DATA CONTROL BOUNDARY OF OUTDOOR C2 24 24 24 24 NEGA MODE W/B R-CONTROL DATA C3 A1 A1 A1 A1 FOCUS RETURN LOW BYTE C4 15 15 15 15 FOCUS RETURN HIGH BYTE C5 A0 A0 A0 A0 ZOOM RETURN LOW BYTE C6 12 12 12 12 ZOOM RETURN HIGH BYTE C7 O5 O5 O5 O5 LENS CHECK MARGIN (WIDE) C8 12 12 12 12 LENS CHECK MARGIN (TELE) C9 65 65 65 65 ADJUST MODE IRIS SETTING DATA CA 7F 7F BF BF D ZOOM RAITO CB O6 O6 O6 O6 AE UP/DOWN OF NEGA MODE BLC CC 00 00 00 00 SETUP ADJUST ENABLE CD 70 70 70 70 HALL AUTO ADJUSTMENT CE D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT CF FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT D0 FF FF FF FF LENS AUTO ADJUSTMENT D1 FF FF FF FF HALL AUTO CHECK D2 FF FF FF FF AGC AUTO CHECK D3 FF FF FF FF LENS CHECK OF PCB LINE D4 FF FF FF FF GYRO SENSOR CHECK (H) D5 FF FF FF FF GYRO SENSOR CHECK (V) D6 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT D7 01 01 01 01 ZOOM/FOCUS CHECK ENABLE D8 20 20 20 20 VR ZOOM CENTER MARGEIN D9 00 00 00 00 COLOR GAIN ADJUSTMENT DA 7E 7E 7E 7E SETUP AUTO ADJUSTMENT DB O8 O8 O8 O8 HALL CHECK THRESHOULD DC 82 82 82 82 COLOR ADJUST TARGET VALUE DD 89 89 89 89 HALL ADJUST GAIN TARGET DE 4D 4D 4D 4D HALL ADJUST CENTER DF 00 00 00 00 NOT USED E0 AA AA AA AA BK NOISE TH/GAIN OF EIS E1 5F 5F 5F 5F H APPERTURE GAIN OF EIS E2 FF FF FF FF #0C OF EIS ON E3 07 07 07 07 #OD OF EIS ON E4 A8 A8 A8 A8 #OE OF EIS ON E5 10 10 10 10 #OF OF EIS ON E6 OO OO OO OO #18 OF EIS ON

Alignment and adjustment

Samsung Electronics 5-9

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT E7 FF FF FF FF AGC CONTROL OF Y SINGNAL E8 69 69 69 69 V GAIN-1(A/D GAIN) E9 80 80 80 80 R TARGET OF W/B AUTO ADJUSTMENT EA EB EB EB EB V GAIN-3(CENTERING GAIN) EB 06 06 06 06 V STOP NOISE THRESHOULD EC 8C 8C 8C 8C H GAIN-1(A/D GAIN) ED 7F 7F 7F 7F B TARGET OF W/B AUTO ADJUSTMENT EE EB EB EB EB H GAIN-3(CENTERING GAIN) EF 09 09 09 09 H STOP NOISE THRESHOULD F0 OO OO OO OO D-ZOOM STEP

6. Initial data of camera parts adjustment - CAMERA AF 2nd MICOM (UPD784035GC-828) DATA - NTSC

SC-L100 SC-L150 MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT CD HALLA 70 70 70 70 HALL AUTO ADJUSTMENT CE IRISRA D0 D0 D0 D0 IRIS CONTROL RANGE ADJUSTMENT CF WBA FF FF FF FF WHITE BALANCE AUTO ADJUSTMENT D0 LENSA FF FF FF FF LENS AUTO ADJUSTMENT D6 Z.CHK 80 80 80 80 ZOOM VR CENTER AUTO ADJUSTMENT O3 IRIS1 70 70 70 70 IRIS LEVEL CONTROL-HIGH BYTE O5 P.CLK 40 40 40 40 P.CLK ADJUSTMENT O7 ADREF OO OO OO OO A/D REFERENCE CONTROL(SETUP) O8 S.CLK 0F 0F 0F 0F SOFT CLIP CONTROL O9 AGC1 18 18 18 18 AGC CONTROL OB HAPER 58 58 58 58 HORIZONTAL APPERTURE GAIN OC YSEL F8 F8 F8 F8 VERTICAL APPERTURE GAIN 1C CWBR 3D 3D 3D 3D COLOR W/B COEFF. OF Cr SIGNAL 1D CWBB 90 90 90 90 COLOR W/B COEFF. OF Cb SIGNAL 32 CRGP 38 38 38 38 INDOOR R-Y POSITIVE GAIN 33 CRGN 38 38 38 38 INDOOR R-Y NEGATIVE GAIN 34 CHYE 09 09 09 09 INDOOR R-Y POSITIVE GAIN 35 CHB O8 O8 O8 O8 INDOOR R-Y NEGATIVE GAIN 36 CBGP 1E 1E 1E 1E INDOOR B-Y POSITIVE GAIN 37 CBGN 18 18 18 18 INDOOR B-Y NEGATIVE GAIN 38 CHGR 18 18 18 18 INDOOR B-Y POSITIVE GAIN 39 PCBHN 01 01 01 01 INDOOR B-Y NEGATIVE GAIN 53 ECGAN 80 80 80 80 CHROMA GAIN CONTROL 54 ESY 83 83 83 83 Y SET-UP LEVEL CONTROL 55 EWC AE AE AE AE WHITE CLIP CONTROL 57 EUSC EE EE EE EE B-Y SIGNAL BURST LEVEL CONTROL 58 EVSC 00 00 00 00 R-Y SIGNAL BURST LEVEL CONTROL 5D XKCON 00 00 00 00 SCK CONTROL 5E MDSEL 01 01 01 01 D/ZOOM MODE SELECTION 5F TGMSE 02 O2 O2 O2 TG MODE SELECTION 65 HRGDL 00 00 00 00 H1/H2/RG DELAY CONTROL 66 SHP.D D9 D9 D9 D9 SHP/SHD DELAY CONTROL 67 ADDL OO OO OO OO SPO/FECKDELAY CONTROL 71 ROUGP 36 36 36 36 OUTDOOR R-Y POSITIVE GAIN 72 ROUGN 2C 2C 2C 2C OUTDOOR R-Y NEGATIVE GAIN 73 CHOYE O5 O5 O5 O5 OUTDOOR R-Y POSITIVE HUE 74 CHOB 13 13 13 13 OUTDOOR R-Y NEGATIVE HUE 75 GOUGP 23 23 23 23 OUTDOOR B-Y POSITIVE GAIN 76 BOUGN 1B 1B 1B 1B OUTDOOR B-Y NEGATIVE GAIN 77 CHOGR 18 18 18 18 OUTDOOR B-Y POSITIVE HUE 78 CHOR 04 04 04 04 OUTDOOR B-Y NEGATIVE HUE 82 AETAL 30 30 30 30 AE TARGET (LOW BYTE) 83 AETAH O5 O5 O5 O5 AE TARGET (HIGH BYTE)