Roland FD-9, KT-9 Users Manual

Owner’s Manual

English

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the
document(s) including those sections where it will be available for immediate reference.

Check the Included Items

After opening the package, check that all of the included items
are present. If anything is missing, contact your dealer.

5 Unit (KT-9/FD-9)

5 Owner’s Manual

5 Connection cable

* A Phillips screwdriver for attaching the weight and anchor bolt is

not included. You’ll need to provide a Phillips screwdriver of the
appropriate size.

KT-9 only

5 Weight

5 Screw

Main Features

This unit is a pedal featuring a stop mechanism using a
link and spring. Since it tends to not produce loud noise
or vibration, it remains quiet, allowing you to enjoy
performing without inconvenience to other people nearby.

By using this unit in conjunction with the separately sold
noise eater (NE-10), you can further reduce any noise or
vibration transmitted to the oor below.

Descriptions

KT- 9

Spring

(Black)

FD-9

(Silver)

* Do not touch the sensor area or insert a foreign object into it. Doing

so will cause faulty operation or malfunction.

Link

Toe stopper

OUTPUT jack

Anchor bolt

KT- 9

Sensor

FD-9

Using the Anchor Bolts

If you’re using this unit on a V-Drums mat, on a noise eater
(NE-10), or on carpet, extending the anchor bolts will secure
the unit in place, making it easier for you to perform.

When using on
the V-Drums mat,
noise eater, or carpet

* When used on ooring, the anchor bolts may damage the oor.

* The tips of the anchor bolts are sharp. Handle with care.

Copyright © 2016 ROLAND CORPORATION

When using on
the oor

Setup

Connections

Connect this unit’s OUTPUT jack to your sound module, using
the connection cable of your sound module or the included
connection cable.

KT-9

Sound
module

TD-30
TD-25/TD-15/
TD-11/TD-1
HPD-20
SPD-30 1/KICK
SPD-SX
TM-2 TRIG IN 1, TRIG IN 2

Connection cable Jack

Connection cable of sound module
(KIK)

Connection cable included with this
unit

KICK

–

TRIG IN

TRIG IN 1/2, TRIG IN 3/4

FD-9

Sound
module

TD-30
TD-25/TD-15/
TD-11/TD-1
HPD-20
SPD-30 HH CTRL

Connection cable Jack

Connection cable of sound module
(HHC)

Connection cable included with this
unit

HH CTRL

–

HH CTRL

Sound Module Settings

KT-9

Sound

Value

module

“TRIGGER”0“TRIGGER
SENSITIVITY”0“KICK”

TD-30

“TRIGGER”0“TRIGGER
ADVANCE”0“THRE”0“KICK”

“MENU”0“SETUP”0“TRIGGER

TD-25

SETTINGS”0“KICK”

TD-15

“KIT MENU”0“SYSTEM”0“PAD
SETTINGS”0“KIK”

TD-11

TD-1 “Pad type” Kick pedal: 3

“MENU”0“SYS”0“ExtTrigger
Settings”0“TYPE”

HPD-20

“MENU”0“SYS”0“Pad
Settings”0“SENS”

“MENU”0“PAD

SPD-30

SETTING”0“EXTERNAL”

“SETUP”0“TRIG IN”0“INPUT
MODE”0“TRIGx2”

or or

SPD-SX

“SETUP”0“TRIG IN”0“INPUT
MODE”0“HEAD&RIM”

“SETUP”0“PAD SENS”

TM-2

“SETUP”0“TRIGGER SETUP”

* Use the Sensitivity setting (Sens) to adjust the sensitivity of the pad

to your taste.

* If double triggering occurs, adjust the sensitivity by increasing the

value of the sound module’s trigger parameter “Threshold.”

* If you’re using any other sound module, set the parameters to

approximately the following values: Sens: 10, Threshold: 13, and Scan
Time: 2.8.

FD-9

Sound

Value

module

TD-30

“TRIGGER”0“TRIGGER HI-HAT”

* This setting is not necessary for sound modules other than the TD-30.

Trig Type: KT-10

Threshold: 13

Type: KT-10
Threshold: 13

Pad Type: KT-10
Threshold: 13

Type: KD-140

Threshold: 13

Type: KD-140
Threshold: 13

TRIG 1 TYPE: KT-10
(“TRIG 3 TYPE” if connected to

the TRIG IN 3/4 jack)

TRIG 1/2 TYPE: KT-10
(“TRIG 3/4 TYPE” if connected

to the TRIG IN 3/4 jack)

THRESHOLD: 13

Type: KT-10
Threshold: 13

Trig Type: VH11

Adjusting the Feeling

By Adjusting the Spring

You can lighten the feeling by
removing either the left or the right
spring.

* Take care not to pinch your nger

when removing or installing a spring.

Remove one or the
other.

2

Detach upper hook.

To reinstall the spring, attach
the upper hook rst.

1

Detach lower hook.

By Attaching the Weight

You can make the feeling heavier by installing the included
weight.

Align the front edges.

1

Use the included screw to
install the weight.

* After installing the weight, make sure that the screw is tight.

Adjusting the feeling will change the amount of

noise/vibration

Be aware that removing a spring or installing the weight
will increase the noise/vibration when performing.

Springs Two One

Noise/vibration Less More

Feeling Heavy Light

Weight Removed Installed

Noise/vibration Less More

Feeling Light Heavy

KT-9 only

Weight

USING THE UNIT SAFELY

WARNING

Do not disassemble or modify by
yourself

Do not carry out anything
unless you are instructed
to do so in the owner’s
manual. Otherwise, you risk
causing malfunction.

Do not repair or replace parts by yourself

Refer all servicing to
your retailer, the nearest
Roland Service Center,
or an authorized Roland
distributor, as listed on the
“Information.”

Do not use or store in the following types
of locations

• Subject to temperature
extremes (e.g., direct
sunlight in an enclosed
vehicle, near a heating
duct, on top of heat­generating equipment);
or are

• Damp (e.g., baths, washrooms, on
wet oors); or are

• Exposed to steam or smoke;
or are

• Subject to salt exposure; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration
and shakiness; or are

• Placed in a poorly ventilated
location.

Do not place in an unstable location

Otherwise, you risk injury
as the result of the unit
toppling over or dropping
down.

Do not allow foreign objects or liquids to
enter unit; never place containers with
liquid on unit

Do not place containers
containing liquid (e.g.,
ower vases) on this
product. Never allow
foreign objects (e.g.,
ammable objects, coins,
wires) or liquids (e.g.,
water or juice) to enter this
product. Doing so may cause short
circuits, faulty operation, or other
malfunctions.

Be cautious to protect children from
injury

Always make sure that an
adult is on hand to provide
supervision and guidance
when using the unit in
places where children are present, or
when a child will be using the unit.

Do not drop or subject to strong impact

Otherwise, you risk
causing damage or
malfunction.

WARNING

CAUTION

Route all power cords and cables in such
a way as to prevent them from getting
entangled

Injury could result if
someone were to trip on a
cable and cause the unit to
fall or topple.

Disconnect all cords/cables before
moving the unit

Damage or malfunction
may result if you fail to
disconnect all cables before
moving the unit.

Take care so as not to get ngers pinched

When using this unit,
take care not to pinch
your ngers. Whenever
a child uses the unit, an
adult should be on hand to provide
supervision and guidance.

Keep small items out of the reach of
children

To prevent accidental
ingestion of the parts listed
below, always keep them
out of the reach of small
children.

Included Parts (KT-9 only):

• Weight

• Screw

Removable Parts:

• Spring

• Screws

IMPORTANT NOTES

Placement

• When moved from one
location to another where the
temperature and/or humidity
is very dierent, water droplets
(condensation) may form inside
the unit. Damage or malfunction
may result if you attempt to
use the unit in this condition.
Therefore, before using the
unit, you must allow it to stand
for several hours, until the
condensation has completely
evaporated.

• Depending on the material and
temperature of the surface on
which you place the unit, its
rubber feet may discolor or mar
the surface.

• In some cases, grease might seep
out from the link, but this is not a
problem for use. If it is a concern,
wipe it o with a soft cloth.

Maintenance

• Never use benzine, thinners,
alcohol or solvents of any
kind, to avoid the possibility
of discoloration and/or
deformation.

Additional Precautions

• To avoid malfunctions, do not
apply excessive force to the jack.

• When disconnecting all cables,
grasp the connector itself—never
pull on the cable. This way you
will avoid causing shorts, or
damage to the cable’s internal
elements.

• This instrument is designed to
minimize the extraneous sounds
produced when it’s played.
However, since sound vibrations
can be transmitted through
oors and walls to a greater
degree than expected, take
care not to allow these sounds
to become a nuisance others
nearby.

Trademarks

• Roland, BOSS, V-Drums, and
Noise Eater are either registered
trademarks or trademarks of
Roland Corporation in the United
States and/or other countries.

• Company names and product
names appearing in this
document are registered
trademarks or trademarks of their
respective owners.

Main Specications

Roland KT-9: Kick Trigger Pedal Roland FD-9: Hi-Hat Control Pedal

Dimensions

Weight 2.0 kg/4 lbs 7 oz

Accessories

Option (sold separately) Noise eater (NE-10)

* In the interest of product improvement, the specications and/or appearance of this unit are subject to

change without prior notice.

139 (W) x 365 (D) x 158 (H) mm
5-1/2 (W) x 14-3/8 (D) x 6-1/4 (H) inches

Owner’s manual, Weight, Screw,
Connection cable

Owner’s manual, Connection cable