Quectel Wireless Solutions 201805EC25AU, IM0002, H28NCSA User Manual

H-28

H-28EU

H-28NCSA

Mobile

Computer

Quick Start

Guide

	Confirm what is in the Box		BC
	-- H-28/H-28EU/H-28NCSA
		A mobile computer with a barcode scanning feature.
	--	USB cable
		Charge/Communication cable & quick charge compliant
		power adapter.
	--	Battery box
		With rechargeable battery.
	--	Hand strap

-- Quick Start Guide

Provides product information and instructions.

* The number of accessories may differ depending on the product configuration. If any of the accessories are damaged or missing, please contact your local representative.

General View

Top View	Bottom View
1. Scan Window	1. Cradle IO connect

Front View		Back View
1.	Front camera	1.	Battery connector
2.	Logo LED	2.	SIM card slot (H-28EU model)
3.	Back key	3.	Micro SD card slot
4.	Home key	4.	Battery cover lock switch
5.	Menu key	5.	Hand strap hook
6.	Scan button	6.	Back camera
7.	Speaker	7.	Flash LED

8.Information LED

9.Charging LED

Side View

1. Earphone connector

2. Scan button

3. Function button

4. Power button

5. Scan button

6. Volume up

7. Volume down

8. USB connecter

Charging Instructions

Battery Installation

The H-28(EU/NCSA) battery pack is initially not fully charged. After installing the battery pack, please charge it via the USB cable or the charging cradle. By default, the battery pack is not installed in the H-28(EU/NCSA) at the factory to avoid damage caused by excessive draining.

Annual replacement of the battery pack can avoid possible risks or abnormalities and ensure maximum performance. Do not store fully charged or (almost) empty batteries for long periods of time. We recommend charging the spared battery packs every two to three months to keep its charge at a moderate level to maximize battery life.

Please remove the hand strap first when opening the battery compartment. Push the battery cover lock switch to open position then remove the battery cover. Please make sure that the battery contacts are properly aligned with the contacts of the terminal. Close the battery cover and push the cover lock switch to lock.

1. Battery slot

2. Battery pack

3. Battery cover

CAUTION

RISK OF EXPLOSION IF

BATTERY IS REPLACED BY

AN INCORRECT TYPE.

DISPOSE OF USED

BATTERIES ACCORDINGTO

LOCAL REGULATIONS

Charging Time

The required charging time depends on the actual application of the H-28(EU/NCSA) and the condition of the battery pack. The H-28(EU/NCSA) is shipped with a Lithium-ion battery but not fully charged. Please fully charge it before the 1st time use.

Charging via USB Cable

Use the provided USB charge & communication cable together with the quick charge compliant power adapter in the standard package to charge the H-28(EU/NCSA) from a power outlet.

Charging via Charging Cradle

Connect the cradle with a power adapter to a power outlet. Place the H-28(EU) on the cradle for charging.

SD/SIM Card Installation (H-28EU/NCSA model)

1.Turn off the H-28EU/NCSA or put it in battery swap mode

2.Remove the battery cover

3.Remove the battery pack by pulling the tab on the end of the battery

4.Lift the retaining door

5.Please see the back view

6.Insert the micro SD card into the left slot

7.Insert the SIM card into the right slot

8.Insert the battery pack into the battery compartment

9.Restore the battery cover and lock the battery cover lock switch

Barcode Data Capture

To scan a barcode label:

1.Point the scan window at the barcode.

2.Tap Scan on the screen or press one of the scan buttons on the H-28(EU/NCSA). The imager will project a green aiming bar. The green aiming bar is used to position the barcode or object within the field of view of the imager.

3.Ensure the entire barcode is within the width area formed by the green aiming bar, then either wait for the timeout or release the scan key to capture the image. A white beam will illuminates the barcode to capture and decode it.