Pioneer XVDV-1000 Service manual

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2002
XV-DV1000
DVD/CD TUNER
XV-DV1000
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
ORDER NO.
RRV2672
Model Type Power Requirement
XV-DV1000 ZUCXJ DC power supplied from other system component 1
XV-DV1000 ZVYXJ DC power supplied from other system component 2
This product is a system(s) component. This product does not function properly when independent ; to avoid malfunctions, be sure to connect it to the prescribed system component(s), otherwise damage may result. Please connect it to the POWERED SUBWOOFER S-DV1000SW, for adjustment and operĀ­ation inspection.
Component System Service Manual Remarks
DVD/CD TUNER XV-DV1000 RRV2672 This Manual
POWERED SUBWOOFER S-DV1000SW RRV2692
SPEAKER SYSTEM S-DV1000ST RRV2697
Regional restriction
codes (Region No.)
Remarks
For details, refer to "Important symbols for good services".
T-ZZK OCT. 2002 printed in Japan
1234

SAFETY INFORMATION

A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 ā€“ Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identical designation.
REMARQUE (POUR MODƈLE CANADIEN SEULEMENT)
C
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les piĆØces de remplacement doivent avoir la mĆŖme dĆ©signation.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
D
E
current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA.
Reading should not be above
0.5 mA
Earth ground
Device under test
Also test with plug reversed (Using AC adapter plug as required)
Test all exposed metal surfaces
Leakage current tester
AC Leakage Test
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNĀ­ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual.
Electrical components having such features are identified by marking with a on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.
on the schematics and
F
2
1234
XV-DV1000
5678
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1. A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm
A
B
LABEL CHECK
Name Lavel
Additional Laser Caution
1. Laser Interlock Mechanism
ā€¢ Loading switch (S101 on the LOAB Assy) is used for interlock mechanism of the laser. When this switch turned ON in SW2 (XCLOSE) side (OPEN signal is 0V and XCLOSE signal is 3.5V), a laser becomes the status which can completely oscillation. Furthermore, the laser completely oscillates in the disc judgment and disc playback. When player is power ON state and laser diode is not completely oscillating, 780nm laser diode is always oscillating by half power.
ā€¢ Laser diode is driving with Q101 (650nm LD) and Q102 (780nm LD) on the DVDM Assy. Therefore, when short-circuit between the emitter and collector of these transistors or the base voltage is supplied for transistors turn on, the laser oscillates. (failure mode)
ā€¢ In the test mode āˆ— , there is the mode that the laser oscillates except for the disc judgment and playback. LD ON mode in the test mode oscillates with the laser forcibly. The interlock mechanism mentioned above becomes invalid in this mode.
C
D
E
2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam.
āˆ— : See page 91.
XV-DV1000
56
F
7
8
3
1234
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
A
When you find the procedures bearing any of the symbols, be sure to fulfill them:
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
B
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
C
ones should be used.
Disc / Content Format PlayĀ­back Compatibility
D
General Disc Compatibility
ā€¢ This player was designed and engiĀ­neered to be compatible with software bearing one or more of the following logos.
DVD-Video DVD-R DVD-RWDVD-Audio
Audio CD CD-R
Video CD
CD-RW
E
Super Audio CDSuper VCD
F
4
1234
XV-DV1000
5678

CONTENTS

SAFETY INFORMATION.......................................................................................................................................................2
1. SPECIFICATIONS..............................................................................................................................................................6
2. EXPLODED VIEWS AND PARTS LIST..............................................................................................................................8
2.1 PACKING.....................................................................................................................................................................8
2.2 EXTERIOR SECTION ...............................................................................................................................................10
2.3 FRONT PANEL SECTION .........................................................................................................................................12
2.4 LOADING MECHA ASSY..........................................................................................................................................14
2.5 TRAVERSE MECHANISM ASSY-S ...........................................................................................................................16
2.6 DISPLAY UNIT ..........................................................................................................................................................17
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...........................................................................................................18
3.1 DVD and Video Section BLOCK DIAGRAM ..............................................................................................................18
3.2 DSP and Control Section BLOCK DIAGRAM............................................................................................................20
3.3 Power Supply Section BLOCK DIAGRAM.................................................................................................................22
3.4 LOAB ASSY and OVERALL WIRING DIAGRAM ......................................................................................................24
3.5 DVDM ASSY (1/4) .....................................................................................................................................................26
3.6 DVDM ASSY (2/4) .....................................................................................................................................................28
3.7 DVDM ASSY (3/4) .....................................................................................................................................................30
3.8 DVDM ASSY (4/4) .....................................................................................................................................................32
3.9 SACDB ASSY............................................................................................................................................................34
3.10 VIDEO (1/2) and REG ASSYS.................................................................................................................................36
3.11 VIDEO (2/2) and COMPONENT ASSYS.................................................................................................................38
3.12 IF ASSY...................................................................................................................................................................40
3.13 FM/AM TUNER MODULE (AXQ7228).....................................................................................................................42
3.14 FM/AM TUNER MODULE (AXQ7229).....................................................................................................................44
3.15 DSP ASSY...............................................................................................................................................................46
3.16 DSP TRADE and CONTROL (1/4) ASSYS .............................................................................................................48
3.17 CONTROL ASSY (2/4) ............................................................................................................................................50
3.18 CONTROL ASSY (3/4) ............................................................................................................................................52
3.19 CONT.(4/4), STBY KEY, D.SW2, KEY L, TIMER LED, KEY R, O/C KEY, MOTOR, D.SW, and HP ASSYS
3.20 OEL CONT and OEL JACK ASSYS........................................................................................................................56
3.21 WAVEFORMS..........................................................................................................................................................58
4. PCB CONNECTION DIAGRAM .......................................................................................................................................59
4.1 LOAB ASSY...............................................................................................................................................................59
4.2 DVDM ASSY..............................................................................................................................................................60
4.3 SACDB ASSY............................................................................................................................................................62
4.4 FM/AM TUNER MODULE..........................................................................................................................................63
4.5 VIDEO, REG and COMPONENT ASSYS..................................................................................................................64
4.6 IF ASSY.....................................................................................................................................................................68
4.7 DSP ASSY.................................................................................................................................................................70
4.8 DSP TRADE ASSY....................................................................................................................................................71
4.9 CONTROL, MOTOR, DOOR SW and HP ASSYS.....................................................................................................72
4.10 STBY KEY, DOOR SW2, KEY L, TIMER LED, KEY R and O/C KEY ASSYS.........................................................76
4.11 OEL CONT and OEL JACK ASSYS........................................................................................................................78
5. PCB PARTS LIST.............................................................................................................................................................79
6. ADJUSTMENT .................................................................................................................................................................89
6.1 DVD SECTION ADJUSTMENT.................................................................................................................................89
6.1.1 Adjustment Items and Location ..............................................................................................................................89
6.1.2 Jigs and Measuring Instruments.............................................................................................................................89
6.1.3 Necessary Adjustment Points.................................................................................................................................90
6.1.4 Test Mode ...............................................................................................................................................................91
6.1.5 Mechanism Adjustment ..........................................................................................................................................92
6.2 TUNER SECTION ADJUSTMENT ............................................................................................................................95
7. GENERAL INFORMATION ..............................................................................................................................................96
7.1 DIAGNOSIS...............................................................................................................................................................96
7.1.1 ID NUMBER AND ID DATA SETTING ....................................................................................................................96
7.1.2 SELF-DIAGNOSIS FUNCTION OF PICKUP DETECTIVE ....................................................................................98
7.1.3 TEST MODE SCREEN DISPLAY ...........................................................................................................................99
7.1.4 SELF-DIAGNOSIS FUNCTION............................................................................................................................101
7.1.5 FUNCTION SPECIFICATION OF THE SERVICE MODE.....................................................................................102
7.1.6 ERROR DISPLAY.................................................................................................................................................103
7.1.7 TEST POINTS LOCATION AND WAVEFORMS...................................................................................................106
7.1.8 TROUBLE SHOOTING.........................................................................................................................................108
7.1.9 SERVICE TEST MODE ........................................................................................................................................109
7.1.10 STANDBY ON TIMING WAVEFORM..................................................................................................................110
7.1.11 SINGLE OPERATION METHOD ........................................................................................................................111
7.1.12 DISASSEMBLY ...................................................................................................................................................112
7.2 IC .............................................................................................................................................................................121
7.3 CLEANING ..............................................................................................................................................................160
8. PANEL FACILITIES ........................................................................................................................................................161
..............
54
A
B
C
D
E
F
56
XV-DV1000
7
8
5
1234

1. SPECIFICATIONS

Amplifier Section
Continuous Power (RMS)..............................75 W / channel
A
(1 kHz, THD 10%, 6 W)
Disc section
Digital audio
characteristics..................................DVD fs: 192 kHz, 24-bit
Type..............................DVD system, Video CD system and
Compact Disc digital audio system Frequency response
48 kHz sampling.........................................4 Hz āˆ’ 22 kHz
96 kHz sampling.........................................4 Hz āˆ’ 44 kHz
192 kHz sampling.......................................4 Hz āˆ’ 88 kHz
S/N ratio......................................................................110 dB
B
Dynamic range..............................................................98 dB
Total harmonic distortion...........................................0.004 %
Wow and Flutter...................................Limit of measurement
(Ā±0.001 % W.PEAK) or less (EIAJ)
FM tuner section
Frequency Range...........................................87.5 - 108MHz
Antenna......................................................75 ā„¦, unbalanced
AM tuner section
FrequencyRange
With 9 kHz step...............................531 kHz to 1,602 kHz
With 10 kHz step.............................530 kHz to 1,700 kHz
C
ā€¢ Frequency step options available with U.S. model only
Antenna............................................................Loop antenna
Accessories
Operating Instructions..........................................................1
Setup guide..........................................................................1
Display unit...........................................................................1
Remote control unit .............................................................1
Power cord...........................................................................1
Video Cord...........................................................................1
Display cable (gray plugs)....................................................1
Control cable (blue plugs)....................................................1
Control cable (black plugs)...................................................1
FM antenna..........................................................................1
AM loop antenna..................................................................1
Dry cell batteries (AA/R6).....................................................2
Allen key wrench..................................................................1
Side panel replacement screws...........................................4
Speaker cords (15ft. / 5 m)...................................................3
Speaker cords (30 ft. / 10 m)................................................2
Sheet of small non-slip pads..............................................20
Sheet of large non-slip pads................................................4
Subwoofer isolation feet (European model)........................4
Warranty Card......................................................................1
Note :
ā€¢ The specifications and design of this product are subject to change without notice, due to improvement.
Miscellaneous
Power Requirements
European model........................220 āˆ’ 230 V / 50 āˆ’ 60 Hz
North American model.................................120 V / 60 Hz
Power Consumption
European model.....................................................176 W
North American model............................................180 W
Power Consumption in standby mode..........................0.4 W
Dimensions:
D
DVD/CD Tuner.................380 (W) x 71 (H) x 299 (D) mm
Display Unit........................220 (W) x 61 (H) x 35 (D) mm
Weight:
DVD/CD Tuner...........................................4.1 kg (6.8 lb.)
Display Unit..............................................0.22 kg (0.4 lb.)
E
15.5 (W) x 2.9 (H) x 12.2 (D) in.
ā€¢ Manufactured under license from Dolby Laboratories.
ā€œDolbyā€ and the double-D symbol are trademarks of
Dolby Laboratories.
ā€¢ā€œDTSā€ is a registered trademark of
DigitalTheater Systems, Inc.
F
6
1234
XV-DV1000
accessories
Remote control unit
ST+
TUNE+
ENTE
R
TUNE
ā€“
MASTER VOLUME
STā€“
STANDBY/O
N
CD
TR
AY
OPEN CLOSE
DOOR OPEN CLO
SE
DV
DFM
/
AM TV
VIDEO
V1/V2/V3
0
1
4
4
Ā”
8
3
7
0
DVD MENU
RETURN
SOUND
TV CONTRO
L
PV
OL
INPU
T
MUTE
PROG
RAM REPEAT
RANDOM
AUT
O
ROOM SETU
P
TEST TONE
123
DVD
SYSTE
M
CH LEVE
LT
CP MENU
SYS ME
NU
DIMMER DVD DISP
SYS DISP
SET UP
SURROUND
ANGLE
AUDIOS
UBTITLE
ZOOM
ADV
ANCED
45 6
7
89
0
LAN
GUAG
E
MAIN
AX0000
SUB
PCM
TELETEXT ON/OFF
TIMER
(CLOCK ADJ)
FOLDERā€“
CLR ENTE
R
/
ā€“ā€“
ā€“
FO
LDER+
Dry cell batteries (size AA/R6P) x 2
Display unit (AXX7142) AM loop antenna
FM antenna
Control cable A Control cable B Display cable V ideo cord
Gray
Yellow plugs
Blue plugs
Power cord
Speaker cords 5 m x 3 (for center, front L-R speakers)
Operating instructions / Warranty
Non-slip pads x20
10 m x 2 (for rear L-R speakers)
Black plugs
Non-slip pads (subwoofer) x4
European model only: Isolation feet x4
Allen key wrench & 4 screws
(ATB7009) (KUCXJI : ADH7007)
(MYXJI, NVXJI : ADH7010)
(KUCXJI : ADG7022) (MYXJI : ADG1154) (NVXJI : ADG1156)
(VDE1024)(ADE7077)(ADE7079)(ADE7064)
(SDS1115) (SDS1116) (SDS1117)
(SDS1118) (SDS1119)
(SEC1635)
(SXK1049)
(SEC1563)
(AEF7007) (ABA7089)
(KUCXJI : AXD7340) (MYXJI, NVXJI : AXD7339)
This product's instructions are contained within the instruction manual of the related system component(s). The manual is packed with those component(s). This product's accessories etc. are packed with its related component(s).
5678
A
B
C
D
XV-DV1000
56
7
E
F
7
8
1234

2. EXPLODED VIEWS AND PARTS LIST

NOTES:
A

2.1 PACKING

B
C
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.)
7
6
5
D
E
2
(1/2)
2
(2/2)
1
3
4
F
8
1234
XV-DV1000
5678
PACKING parts List
Mark
Mark No. Description Part No.
1 Front Pad AHA7393 2 Rear Pad AHA7394 3 Spacer AHB7066 4 Packing Case See Contrast table (2) 5 Packing Sheet AHG7015
No. Description Part No.
6 Packing Sheet AHG7073 NSP 7 Warranty Card See Contrast table (2)
(2) CONTRAST TABLE
XV-DV1000/ZUCXJ and ZVYXJ are constructed the same except for the following :
Mark NO Symbol and Description
4 Packing Case AHD8095 AHD8094 NSP 7 Warranty Card EL ARY7007 Not used NSP 7 Warranty Card Not used ARY7022
XV-DV1000/
ZUCXJ
XV-DV1000/
ZVYXJ
A
B
C
D
E
56
XV-DV1000
F
7
8
9
1234

2.2 EXTERIOR SECTION

J
E
24
58
XV-DV1000/ZUCXJ Only 53
52
D
L
R
57
57
C
S
57
55
41
60
26
Z
55 55
58
23
J
W
Q
K
J
38
6
9
H
G
34
57
U
5
62
19
H
20
55
12
15
55
U
F
K
T
E
55
55
57
30
G
57
H
C
2
A
21
B
C
D
E
48
Refer to "2.4 LOADING MECHA ASSY".
13
M
57
55
B
50
57
D
55
17
59
27
Q
1
18
K
55
10
L
39
S
57
57
22
57
28
N
O
P
57
V
L
M
N
O
P
25
16
57
42
57
F
E
43
55
Q
11
57
40
57
47
G
14
(1/2)
B
57
A
46
33
36
56
47
(2/2)
37
4
35
61
61
XV-DV1000/
I
3
ZUCXJ Only
55
8
7
R
F
W
55
V
55
29
D
44
45
F
10
1234
57
57
C
Refer to "2.3 FRONT PANEL SECTION".
32
57
A
T
B
Z
54
XV-DV1000
63
31
32
51 49
59
NON-CONTACT
SIDE
CONTACT SIDE
5678
EXTERIOR SECTION parts List
Mark No. Description Part No.
1 DVDM Assy AWX8156 2 SACDB Assy AWX8157 3 DSP Assy AWX8188 4 DSP TRADE Assy AWU7981 5 CONTROL Assy See Contrast table (2)
6 VIDEO Assy See Contrast table (2) 7 REG Assy AWU8046 8 COMPONENT Assy See Contrast table (2) 9 IF Assy AWU7987 10 STBY KEY Assy AWU7992
11 O/C KEY Assy AWU7993 12 FM/AM TUNER Module See Contrast table (2) NSP 13 LOADING MECHA Assy VWT1188 14 20P FFC/30V ADD7383 15 40P FFC/30V ADD7384
16 07P FFC/30V ADD7385 17 30P FFC/30V ADD7386 18 21P FFC/30V ADD7387 19 21P FFC/30V ADD7388 20 13P FFC/30V ADD7391
21 Connector Assy PG05KK-G15 22 Connector Assy PG13KK-G25 23 Connector Assy PG14KK-G17 24 DC FAN Motor AXM7024 25 Ferrite Core ATH7009
26 Earth Spring ABH7223 27 Adapter 12 L ANW7231 28 Adapter 12 R ANW7245 29 Bottom Plate ANA7143 30 Rear Panel See Contrast table (2)
31 Bottom Base AMA7027 32 Leg AEB7090
Mark
No. Description Part No.
NSP 33 PC Support VEC1749 34 MSPLS Support AEC7450 35 DSP Angle ANG7436
36 Rubber Bushing AEB7291 37 FFC Barrier AEC7451 NSP 38 PCB Spacer (3X6) AEC7156 39 Angle L ANG7434 40 Angle R ANG7435
41 Leg AEB7197 42 FAN Barrier AEC7452 43 Push Rivet AEC7025 44 Tray Cap AAK8052 45 DVD-A/V Plate VAM1118
46 Top Panel ANE7301 47 Top Button Assy AXG7166 48 Side Panel L See Contrast table (2) 49 Side Panel R See Contrast table (2) 50 Side Sheet L AWL7062
51 Side Sheet R AWL7063 52 Label VRW1872 53 65 Label See Contrast table (2) NSP 54 Name Label See Contrast table (2) 55 Screw BPZ30P080FZK
56 Screw (3*11.5) ABA7071 57 Screw BBZ30P080FMC 58 Screw A ABA7088 59 Screw C ABA7091 60 Screw PSC30P080FNI
61 FAN Spaser AEB7293 NSP 62 ID Label VRW1877 NSP 63 Label VRW1629
A
B
C
D
(2) CONTRAST TABLE
XV-DV1000/ZUCXJ and ZVYXJ are constructed the same except for the following :
Mark NO Symbol and Description
5 CONTROL Assy AWU7982 AWU7979
6 VIDEO Assy AWU7983 AWU7980
8 COMPONENT Assy AWU7984 Not used
12 FM/AM TUNER Module AXQ7228 AXQ7229
30 Rear Panel ANC8110 ANC8093
48 Side Panel L AAK8081 AAK8050
49 Side Panel R AAK8082 AAK8051
53 65 Label ARW7050 Not used NSP 54 Name Label AAK7295 AAK7294
XV-DV1000/
ZUCXJ
XV-DV1000
56
XV-DV1000/
ZVYXJ
7
E
F
11
8
1234

2.3 FRONT PANEL SECTION

A
15
41
41
37
(4/4)
3
B
35
C
M
A
37
33
34
41
42
(1/4)
23
19
(2/2)
19
(1/2)
41
21
17
28
42
S
29
7
27
10
4
31
11
30
41
6
R
20
42
9
43
42
22
41
24
41
16
41
40
29
2
A
N
13
8
(2/4)
O
37
37
(3/4)
41
42
5
P
1
26
42
18
T
42
18
36
39
18
42
D
E
25
38
14
32
18
12
14
39
Refer to "Cable Styling in Main Unit Assembly" of "7.1.12 DISASSEMBLY"
F
12
1234
XV-DV1000
NON-CONTACT
SIDE
CONTACT SIDE
Shaft bearing
Axis of rotation for Cam Gear R, Boss for sliding gutter of Cam R
Gear Pulley A Cam Gear L
Cam L
Shaft
Gear Holder L
Gear Holder R
Synchro Gear
Axis of rotation for Gear A and Gear B
Sliding part of Cam R and Arm R
Axis of rotation for Gear Pulley A
Front Panel
Synchro Gear
Lubricating Oil GYA1001
Lubricating Oil GYA1001
Lubricating Oil GYA1001
Application of Lubricant
Lubricating Oil GYA1001
Lubricating Oil GYA1001
Axis of rotation for Cam Gear L, Boss for sliding gutter of Cam L
Lubricating Oil GYA1001
Sliding part of Cam L and Arm L
Lubricating Oil GYA1001
Cam Gear R
Cam R
Shaft bearing
Lubricating Oil GYA1001
5678
FRONT PANEL SECTION parts List
Mark No. Description Part No.
1 HP Assy AWU7988 2 KEY L Assy AWU7989 3 DOOR SW2 Assy AWU7990 4 KEY R Assy AWU7991 5 TIMER LED Assy AWU7994
6 MOTOR Assy AWU7995 7 DOOR SW Assy AWU7996 8 07P FFC/30V ADD7389 9 Connector Assy 5P ADE7089 10 Slider Motor VXM1033
11 Ferrite Core ATH7010 12 Door Cover ANG7437 13 Reļ¬‚ector Sheet AAK8073 14 Door Spring ABH7224 15 Spring AL ABH7225
16 Spring AR ABH7226 17 Belt AEB7171 18 Cushion AEB7292 19 Gear Holder L AMR7427 20 Gear Holder R AMR7428
21 Cam Gear L AMR7429 22 Cam Gear R AMR7430
Mark
No. Description Part No.
23 Cam L AMR7431 24 Cam R AMR7432 25 Arm L ANG7421
26 Arm R ANG7422 27 Gear A ANW7063 28 Gear Pulley A ANW7066 29 Gear B ANW7250 30 Shaft Assy AXG7161
31 Motor Pulley PNW1634 32 Door Escutcheon AAK8046 33 DVD Lens AAK8048 34 STBY Lens AAK8049 35 Front Panel AMB7821
36 Front Panel See Contrast table (2) 37 Front Button Assy AXG7167 38 Door Assy See Contrast table (2) NSP 39 Binder (BK-1) ZCA-BK1 40 Screw PMZ26P040FMC
41 Screw Z39-019 42 Screw BPZ30P080FZK 43 Screw With Washer ABA1005
A
B
C
(2) CONTRAST TABLE
XV-DV1000/ZUCXJ and ZVYXJ are constructed the same except for the following :
Mark NO Symbol and Description
36 Front Panel ANB7304 ANB7293 38 Door Assy AXG7178 AXG7168
XV-DV1000/
ZUCXJ
XV-DV1000/
ZVYXJ
D
E
56
XV-DV1000
F
7
8
13
1234

2.4 LOADING MECHA ASSY

Note :
A
Refer to
8
6
To DVDM CN101 (pickup)
" Application of Lubricant".
8
2
Refer to "2.5 TRAVERSE MECHANISM ASSY-S".
20
18
22
19
13
12
8
8
17
16
4
To DVDM
CN104 (stepping) To DVDM CN105 (spindle)
3
A
5
Daifree GEM1036
B
Lubricating Oil
23
C
GYA1001
22
15
14
D
LOADING MECHA ASSY parts List
Mark
No. Description Part No.
NSP 1 LOAB Assy VWG2279 2 Traverse Mechanism Assy-S VXX2782 3 Loading Motor Assy VXX2505 4 Motor Pulley PNW1634
E
5 Carriage DC Motor / 0.3W PXM1027
6 Flexible Cable (26P) VDA1864 7 Connector Assy 2P VKP2253 8 Floating Rubber VEB1327 9 Belt VEB1330 10 Stabilizer VNE2253
22
21
22
7
A
10
11
9
1
A
22
Mark No. Description Part No.
16 Drive Gear VNL1923 17 SW Lever VNL1925 18 Clamper Plate VNE2251 19 Bridge VNE2252 20 Clamper VNL1924
21 Screw JGZ17P028FMC 22 Screw Z39-019 23 Tray VNL1920
Lubricating Oil GYA1001
11 Loading Base VNL1917 12 Float Base DVD VNL1918 13 Drive Cam VNL1919
F
14 Gear Pulley VNL1921 15 Loading Gear VNL1922
14
1234
XV-DV1000
5678
Application of Lubricant
No. 11 Loading Base
Lubricating Oil GYA1001
Around the shaft
Concave of unevenness
Concave of unevenness
Concave of unevenness
No. 13 Drive Cam
No. 13 Drive Cam
No. 23 Tray
No. 23 Tray
Top View
Rear View
Top View
Bottom View
Daifree GEM1036
Daifree GEM1036
Daifree GEM1036
Daifree GEM1036
Daifree GEM1036
Side of the rib
Inner side of a ditch
Inner side of a ditch
Lubricating Oil GYA1001
Lubricating Oil GYA1001
Inner side of a ditch
Lubricating Oil GYA1001
Lubricating Oil GYA1001
Lubricating Oil GYA1001
A
B
C
D
E
XV-DV1000
56
F
7
8
15
>
1234

2.5 TRAVERSE MECHANISM ASSY-S

A
18
17 (Torque : 0.12 Ā± 0.01 Nā€¢m)
12
8
Silicone Adhesive GEM1037
3
10
18
13
1
16
B
C
18
10
To DVDM
CN105
7
14
9
6
19
Silicone Adhesive
4 (Adjustment Screw)
5
5
Screw Tight GYL1001
17 (Torque : 0.12 Ā± 0.01 Nā€¢m)
16
17 (Torque : 0.12 Ā± 0.01 Nā€¢m)
15
GEM1037
Silicone Adhesive GEM1037
2
To DVDM
CN101
D
11
TRAVERSE MECHANISM ASSY-S parts List
Mark No. Description Part No.
1 Spindle Motor VXM1088 2 Stepping Motor VXM1090
E
F
3 Pickup Assy-S OXX8003 4 Skew Screw VBA1080 5 Skew Spring VBH1335
6 Guide Bar VLL1514 7 Sub Guide Bar VLL1515 8 Hold Spring VNC1017 9 Joint Spring VNC1019 10 Support Spring VNC1020
NSP 11 Mechanism Chassis VNE2248 12 Slider VNL1811 13 Spacer VNL1913 14 Joint VNL1914
To DVDM
CN104
NON-CONTACT
Mark No. Description Part No.
15 FFC Holder VNL1915
16 Screw BBZ20P050FZK 17 Tapping Screw OBA8009 18 Screw PMA26P100FMC 19 Damper Sheet VEB1335
SIDE
CONTACT SIDE
16
1234
XV-DV1000
5678
U
V
8
9
10
3
1
7
5
5
12
12
13
11
12
6
4
2
CONTACT SIDE
NON-CONTACT
SIDE

2.6 DISPLAY UNIT

A
B
DISPLAY UNIT parts List
Mark No. Description Part No.
1 OEL CONT Assy AWU7999 2 OEL JACK Assy AWU8000 3 OEL Module MXK8044 4 18P FFC / 30V ADD7392 5 Leg AEB7090
6 OEL Cushion AEB7273 7 Shield Cover ANG7438 8 Window AAK8045 9 Disp AL AAP7089 10 Disp Panel AMB7828
11 Disp Cover AMC7049 12 Screw BPZ30P080FZK 13 Screw PSC30P080FNI
C
D
E
56
XV-DV1000
7
F
17
8
1234

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 DVD and Video Section BLOCK DIAGRAM

A
SACDB ASSY
C
DSD_LS
DSD_LFE
DSD_C55DVADML
DSD_L
71
69
7464
IC901
CXD2753R
B
SACD Decoder
126
169-176
IC902
HY57V161610DTC-8
16M SDRAM
IC801
XCA56367PV150
DVD-Audio
DSP
10
138
48
CN999
6
(21P)
10 14 16 18
2
DSD_L
DSD_LS
DSD_LFE
DSD_C
DSADML
SD025SD014SD00
DATA1A
DATA2A
DATA1S
DATA2S
DATA2R
DATA2
DATA1A
DATA2A
a
IC786
3
2
DATA1A0
DATA2A0
166
167
AO0
AO1
AO2
DOUT0
170
IC751
AV-1
184-186, 188-192
IC781
M2V64S40DTP-7
64M SDRAM
33M
CN912
(30P)
2
4
15
19
17
21
23
25
DATA1
DATA2
V
Y
C
Y/G/P_Y
Cb/B/P_Cb
Cr/R/P_Cr
DATA1
DATA2
DATA1R
DATA0R
DATA1
DATA0B
DATA0
DOUT
CN561
11 14
(21P)
PD0-PD7
DVDM ASSY
B
24
RFSACD RFSACD
17
RFSACD
BD0-BD7
8-12, 35-37
BD0-BD7
4-6, 29-33
CN901
(40P)
CN542
(40P)
CN801
(20P)
CN513
(20P)
DATA0A
6 14 13 17 18 19
DATA0S
15 14 13 4 3 2
AO0
13 17 18
C
2
IC211
TK15404M
FE
RF PH
IC201
LC78652W
Servo DSP
XIN
3
DSPRF
RF BH
EFMIN
36M
33M
16M
ROMXA
LOD POS
AIN
172 185
4 5
189
Control CPU
57
IC701
PE5286A
CDDT
DVD Decoder
DMCK
EBY-CHIP
DMACKI
CKCD
IC741
HY57V16160DTC-8
16M SDRAM
IC601
PD6345A
System
FR
AN7
105
44Ɨ48
14 3 13 9 10 15
13,14,
19-24
ADATA0
PK4
(For IC751)
FSEL1
Clock Generator
BD0-BD7
CDDATA
194
22/24AV1
VYW2060
16M Flash Memory
27M
(For IC201,IC701)
16M
CLK27M
CLK16M
IC481
SM8707DV
CN101
RF+
11
B1
20
B2
21
B3
15
B4
16
T DRV
25
T RTN
24
F DRV
23
F RTN
26
ST1+
ST1Ā­ST2+ ST2-
LOAD-
LOAD+
SW2
SW1(GNDS)
(26P)
11 20 21 15 16
25 24 23 26
CN104
(4P)
3 4 2 1
CN105
(12P)
4-9
CN103
(5P)
1 2 4 5
3 5 4 7 6
12 13
9
10
RFP PD2 PD1 PD4 PD3
VM4+ VM4Ā­VM3Ā­VM3+
VM1-34VM1+
35
IC101
LA9704W
RF IC
IC351
M56788AFP
FTS Driver
VM2-
VM2+
31 15 14
32
RFO
BHMIX
IN3-
IN4-
VM5-
RFO AIN
60
BH
49
PH
BH
52
FE
FE
41
TE
TE
42
32047
48
VM5+
9-14
IC251
BA6664FM
Spindle Driver
Q106
32 33 30 39 331
TE
FDO
TDO
SPDO
46 46
16M
SPDO
21
(26P)
SPINDLE
MOTOR
OEIC
PICKUP
ASSY
D
STEPPING
MOTOR
LOAB ASSY
A
E
LOADING
MOTOR
ASSY
2 1
+ā€“
1 2
M
CN602
(2P)
3.3V
S101
M
CN601
(5P)
4 5
27M
IC603
(For IC701)
36M
201-208
36M
TC74VHC541FT
7
AO00
164
M65776AFP
MPEG2 Decoder
CDDIN
163 106
CLKIN
172
ACLKI
(For IC751)
22/24AV1
(For IC701)
22/24M
CLK33M
a
OUT_V
27-34
123-126,
PB0-PB9
F
IC901
HY57V161610DTC-8
16M SDRAM
IC902
PM0033A
Progressive and
High-Quality
Video Encoder
128,129, 131-134
137-140, 143,144, 146-149
PC0-PC9
14-16, 17,18, 26-30
2-9,
12,13
IC831
ADV7300AKST
12 Bit Video
Encoder
44
43
42
39
38
37
OUT_YS
OUT_C
OUT_Y/G
OUT_CB/B
OUT_CR/R
Q932
Q933
Q934
Q936
Q939
Q938
18
1234
XV-DV1000
DATA0
DOUT
CN8606
(21P)
11 14
5678
A
CN8604
G
IF ASSY
IC8601 (1/2)
NJM4560M
IC8602 (1/2)
NJM4560M
IC8603 (1/2)
NJM4560M
IC8603 (2/2)
NJM4560M
IC8604 (1/2)
NJM4560M
2
1
3
2
1
3
2
1
3
5
7
6
2
1
3
(17P)
17 13
9 7 5
CN8603
(17P)
8 5
15
FL
SL
C
SW
SCARTOUTL
DMIXRECL
SCARTINL
DOUT
K
K
CN8302
B
CN8301
DSD_L
DSD_LS
DSD_LFE
DSD_C
DSADML
DATA1
DATA2
Y/G/P_Y
Cb/B/P_Cb
Cr/R/P_Cr
VIDEO1 IN
VIDEO2 IN
VIDEO3 IN
SVIDEO1
SVIDEO2
SVIDEO3
CN1401
(21P)
CN8801
(30P)
V
Y
C
JA8803
JA8801
JA8801
JA8806
IN
JA8802
IN
JA8802
IN
9 12
DATA0
9 12
DOUT
CN8605
(18P)
CN1402
(18P)
8
C
FL
SL
SW
DMIXRECL
8
441212141418183
CN8602
3
(18P)
SCARTINL
CN1404
(18P)
1 15
DOUT
SCART OUT L
1 13
CN8601
(16P)
CN1403
(16P)
C
IC1401
DSD1702EG
12
8 6 4
20
2
4
15
19
17
21
23
25
1
9
4
IC1402
DSD1702EG
1
9
4
IC1403
DSD1702EG
C / SW
1
9
2
10
4
IC1404
DSD1702EG
REC L
1
9
IC8802-IC8804
TC74HC4052AFT
15 14 12 11
15 14 12 11
15 14 12 11
FL
SL
IC8803
13
IC8802
13
IC8804
13
V SEL
Y SEL
C SEL
CB/B IN
IC8801
LA73054
Video Driver Amp.
V IN
2
Y IN
8
C IN
6
Y/G IN
11 14
Cr/R IN
16
33
28
31
25 23 21
V OUT
Y OUT
C OUT
Y/G OUT
CB/B OUT
Cr/R OUT
IC8807
MM1507XN
L
6 4
H
IC8806
MM1505XN
L
6 4
H
IC8808
MM1507XN
L
6 4
H
IC8809
MM1505XN
L
6 4
H
IC8810
MM1505XN
L
6 4
H
2
2
2
Y C
2
Y C
2
XV-DV1000/ZVYXJ ONLY
JA8805
(21P)
L OUT
3
L IN
6
V/Y OUT
19 15
R/C
G
11
7
B
JA8803
VIDEO1
JA8803
MONITOR
JA8806
SVIDEO1
JA8806
MONOTOR
CN8805
(4P)
Y
1
Cb
2
Cr
3
AV CONNECTOR (RGB)-TV
VIDEO OUT
J8806
(4P)
1 2 3
F
SVIDEO OUT
JA8807
Y
Cb
COMPONENT
Cr
COMPONENT ASSY
D
E
F
XV-DV1000/ZUCXJ
VIDEO ASSY
D
XV-DV1000
56
7
ONLY
19
8
1234

3.2 DSP and Control Section BLOCK DIAGRAM

A
B
C
DISPLAY UNIT
U
IC1902
D
PD3430AK
OEL Controller
OEL CONT ASSY
OEL Module
MXK8044
CN5003
IC1901
PD5797A
Display ĀµCOM
IC1903
PD8103A
Font ROM
CN5001
(10P)
ANTENNA
OEL JACK
V
ASSY
RPM7140-HS
CN5101
(10P)
BN201
FM
AM
IC5101
FM/AM TUNER
H
MODULE
IC201
1
BA1451F
AM/FM IF
20
+ MPX IC
CN8603
CN8604
CN5651
(10P)
11
G
G
CN201
(13P)
TXL
7
VIDEO1 L IN
VIDEO2 L IN
VIDEO3 L IN
TV L IN
DMIXRECL
SCARTINL
DOUT
SW
SCARTOUTL
K
CN5701
(13P)
7
JA8103
JA8101
JA8101
JA8101
CN8301
(17P)
8 5
15
CN8302
(17P)
FL
17
SL
13
C
9 7 5
CN5201
(10P)
CONTROL ASSY
IC8101
BU4051BCF
Audio Input
Selector
5 2 4
1 13 14 15
IC8103 (2/2)
NJM4558M
Buffer
5
3
6
7
E
F
DSP ASSY
I
IC8101
CS493292
DSP
D0-D7
IC8201
PD8104A
ROM for D.D & DTS
20
SD01-SD03
39-41 11-13
D0-D7
IC8202, IC8203
TC74VHC574F
Flip Flop
A0-A14
6 43 41 39 37
IC8301
AK4586VQ
Codec & DIR
CN8002
CN8003
32 30 28 27 26
(11P)
2 3 6 4 5
(15P)
3
7 11 13 15
RX1
RX2
TX
RX3
RX4
RECL
FL
LS
SW
C
CN8705
(11P)
2 3 6 4 5
CN8706
(15P)
3
7 11 13 15
CN8701
CN8702
CN8001
(21P)
CN8704
(21P)
DSP TRADE
J
ASSY
CN5502
(23P)
RX1
2
RX2 COAX IN
1
TX
21
RX3
23
RX4
22
RECL
13
FL
9
LS
5
SW
3
C
1
CN5503
(23P)
(23P)
2 1
21 23 22 13
9 5 3 1
(23P)
DOUT
OPTOUT
OPTIN
IC8201
TC74HCU04F
4
2
3
IC5501
PDC099A
ĀµCOM
Control
1
JA8203
JA8202
JA8201
DIGITAL COAX IN
DIGITAL OPT OUT
DIGITAL OPT IN
XV-DV1000
1234
5678
OPEN
CLOSE
BA6417F
FIN
4
RIN
5
IC8001
Motor
OUT1
OUT2
1 7
JA8103
CN1901
(7P)
J8001
(4P)
1 3 4
VIDEO1 L OUT
CN1902
CN8001
SWITCH
OPEN
CLOSE
N
(7P)
(4P)
1 3 4
R
KEY L ASSY
MOTOR ASSY
M
DOOR
MOTOR
J1905
(2P)
J1915
(2P)
J1901
(4P)
J8004
(2P)
2
CN1916
CN1906
SWITCH
M
(2P)
L
(2P)
O
J1901
(4P)
CN8003
(2P)
DOOR SW2 ASSY
STBY KEY ASSY
TIMER LED ASSY
DOOR SW
S
ASSY
2
J1903
(3P)
J1903
(3P)
P
KEY R ASSY
J1913
(2P)
Q
CN1914
(2P)
O/C KEY ASSY
A
B
C
LPF & Gain
IC8301 (1/2)
BA4558F
2
1
0 dB
3
IC8302 (1/2)
BA4558F
3
1
11 dB
2
IC8303 (2/2)
BA4558F
6
7
11 dB
5
IC8303 (1/2)
BA4558F
3
1
8 dB
2
IC8401
BA4053BCF 1 2
13 12
IC8402
BA4053BCF
13
5
3
12
HP ASSY
IC3902
LC75344M
1 2
15
14
14
4
IC3901 (2/2)
NJM4560M
HP Amp.
5
7
6
3
2 6
5 3
2 6
5 3
2 6
5 3
2 6
5
IC8501 (1/2)
BA4558F
1
IC8501 (2/2)
BA4558F
7
IC8503 (1/2)
BA4558F
1
IC8503 (2/2)
BA4558F
7
IC8506 (1/2)
BA4558F
1
IC8506 (2/2)
BA4558F
7
IC8505 (1/2)
BA4558F
1
IC8505 (2/2)
BA4558F
7
CN3901
(5P)
1
CN8501
(12P)
2
3
10
12
5
1
11
7
CN3902
(5P)
HPL
FLN
FLP
SLN
SLP
A
To
SWP
Subwoofer
SWN
CN
CP
1
JA3901
PHONES
T
D
E
F
56
XV-DV1000
7
8
21
1234

3.3 Power Supply Section BLOCK DIAGRAM

A
B
C
ASSY
CN601
V+3D
SPINDLE
MOTOR
PICKUP
ASSY-S
D
(5P)
VIDEO ASSY
V+33DAC
8 8
IC1014
BA033FP
3.3V REG
LOAB
A
DVDM ASSY
B
CN103
(5P)
33
V+3D
CN105
(12P)
11
V+5S
CN101
(26P)
V+5S
IC1016
S-8540B00FN-IMA
DC-DC Converter
3 7
V+5D SW+5V+5S
V+33DVD
VOUTVIN
IC1018
BA12FP
12V REG
V+25V
V+12
V12M
V+6EV
V+6M
1291113
VD+5DVD
VM+6DVD
VM+12DVD
1291113
IC1017
PQ025EH01ZP
2.5V REG
MM1561JF
V+3D V3VD
CN401
V+25DVD
V+33DVD
CN1002
IC1011
BA12FP
12V REG
IC791
1.8V REG
(13P)
(13P)
Q1001
CN513
V+3D
V18D
(20P)
Q1007
C
1919
CN801
(20P)
VA+5DAC
SACDB ASSY
IC906
BA25BC0FP
2.5V REG
IC1015
BA05ST
5V REG
IC1010
BA06SFP
6V REG
V+25V
VIN
J1003
CN1003
IC1012
BA05FP
5V REG
V+3D
3 1
VOUT
3 1
VA+12VV+12VX+12
E
REG ASSY
(4P)
(4P)
VD+5VV+5
IC1013
CN1001
(14P)
1179
4 12 2 1
BA05FP
5V REG
OEL
VD+5
VD+5
VD+5
U
CONTROL ASSY
2 9 1
CN5001
(10P)
DSP ASSY
I
CN8001
(21P)
3 4
V+11OEL V+33OEL VD+5
VD+5
VP+6
VP+12
VD+5DSP
IC5504
NJM7805DL1A
5V REG
VP+6
CN5507
(14P)
VA+12
VA-12
VA+12
VE+56
VA-12
Q8113
Q8114
R8433
R8434
VX+12
VA+5
VA-5
VA+7
VA-7
D8401
D8402
Q5701
10V REG
VD+5
VD+5
CN5201
CN5502
CN8301
VD+5
VA+12
VA-12
CN5701
(10P)
(23P)
(17P)
(13P)
3 9
10
VD+5
20
20
VD+5
21
21
VD+5
10
10
VA+12
12
12
VA-12
9
9
+10V
11
11
VP+3
V+33OEL
V+11OEL
1179
4 12 2 1
D
E
F
VP+3
VP+12
VP+6
From
VP+6
Subwoofer
VA-12
UNE+56
6
4
2 3
10
8
CN5506
(20P)
VP+12
VP+6
IC1019
VA-12
OEL JACK
V
ASSY
CN5651
(10P)
3 9
10
CN5101
DSP TRADE
J
ASSY
CN8701
(23P)
G
CN8603
(17P)
IF ASSY
CN8704
VD+5 VA+12
VA-12
FM/AM TUNER
H
MODULE
+10V
CN201
(13P)
(10P)
(21P)
2 9 1
V+11OEL
V+33OEL
3 4
22
1234
XV-DV1000
5678
A
B
C
D
E
56
XV-DV1000
F
7
8
23
1234

3.4 LOAB ASSY and OVERALL WIRING DIAGRAM

Note : When ordering service parts, be sure to refer to
A
"EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
DSP ASSY (AWX8188)
I
DSP TRADE ASSY (AWU7981)
J
B
PICKUP ASSY-S (OXX8003)
CN101
L
STBY KEY ASSY (AWU7992)
M
DOOR SW2 ASSY (AWU7990)
C
(RF)(RF)
(F)
(F) (F)
D
(T)
SPINDLE MOTOR
E
STEPPING
MOTOR
(VXM1090)
(F)(F)
(T)
(VXM1088)
(S)
(S)
(F) (F) (T)(T)
(T)(T) (F) (F)
(F)
(T)
(T)
(F)(F)
CN105
(S)
(S)
CN104
B 1/4- B 4/4
B
DVDM ASSY (AWX8156)
SACDB ASSY
C
(AWX8157)
D 1/2- D 2/2
D
VIDEO ASSY
(XV-DV1000/ZUCXJ : AWU7983)
(XV-DV1000/ZVYXJ : AWU7980)
A
LOAB ASSY (VWG2279)
F
LOADING MOTOR
ASSY (VXX2505)
A
24
S101
VSK1011
S2B-PH-K
S5B-PH-K
1234
CN103
XV-DV1000
5678
TIMER LED
O
ASSY (AWU7994)
KEY L ASSY
N
(AWU7989)
DVD
DOWNLOAD
P
KEY R ASSY (AWU7991)
T
HP ASSY (AWU7988)
Q
O/C KEY ASSY (AWU7993)
H
FM/AM TUNER MODULE
(XV-DV1000/ZUCXJ : AXQ7228) (XV-DV1000/ZVYXJ : AXQ7229)
IF ASSY
(AWU7987)
G
DOOR SW
S
ASSY (AWU7996)
MOTOR
R
ASSY (AWU7995)
DISPLAY UNIT
U
CN5001
CN5101
V
CN5651
OEL CONT ASSY (AWU7999)
OEL JACK ASSY (AWU8000)
L
TV INPUT
R
L
VIDEO2 INPUT
R
L
VIDEO3 INPUT
R
A
B
C
XV-DV1000/ZVYXJ ONLY
(RGB)-TV
AV CONNECTOR
DC FAN MOTOR (AXM7024)
REG ASSY
E
(AWU8046)
F
COMPONENT ASSY (AWU7984)
COMPONENT
XV-DV1000/ZUCXJ ONLY
L
VIDEO1 INPUT
R
K 1/4- K 4/4
K
CONTROL ASSY
(XV-DV1000/ZUCXJ : AWU7982)
(XV-DV1000/ZVYXJ : AWU7979)
L
VIDEO1 OUTPUT
R
COAXIAL
OPTICAL
OPTICAL
A
B
To Subwoofer (S-DV1000SW)
DIGITAL INPUT
DIGITAL OUTPUT
D
E
F
56
XV-DV1000
7
8
25
1234

3.5 DVDM ASSY (1/4)

A
B 1/4
DVDM ASSY (AWX8156)
(RF)
: RF SIGNAL ROUTE
(RF_V)
: RF (VIDEO) SIGNAL ROUTE
(RF_A)
: RF (AUDIO) SIGNAL ROUTE
(AD)
: AUDIO DATA SIGNAL ROUTE
(F)
: FOCUS SERVO LOOP LINE
(T)
: TRACKING SERVO LOOP LINE
(S)
: STEPPING SERVO LOOP LINE
Buffer
Buffer
(RF)
(RF_V) (RF_V)
(RF)
(RF) (RF)
B
(RF_A)
(RF)
(RF_A)
Buffer
(RF)
2
(RF_A)
1
(RF) (RF)
(F)
(T)
RF IC
(T)
(F)
C
LD Driver
for DVD
LD Driver
for CD
B 2/4
SW for
Detect Signal
(T)
(F)
B 2/4
4
D
E
F
(RF) (RF)
(F) (F) (T)
PICKUP ASSY-S
(T) (F) (F)
(T)
(F)
CN601
A
STEPPING
MOTOR
B 1/4
26
1234
B 2/4
(S)
(F)
(T)
(F)
(T)
(T)
(F)
(F)
B 2/4
(S)
(S) (S)
(S)
(F)
XV-DV1000
(S)
(S)
(S)
Focus, Tracking
and Loading Driver
(T)
(F)
(T)
(T)
(F)
(F) (F)
(T)
B 2/4
(T)
SPINDLE MOTOR
5678
B 3/4
(RF_V) (RF_V)
(RF_A)
(RF_A)
VCO Circuit
(RF_V)
B 3/4
B 2/4
2/2
1/2
(RF_V) (RF_V)
B 2/4
(AD)(AD)
6
B 3/4
B 2/4
A
B 3/4
B
B 2/4
C
(T)
(F)
(RF_A)
B 2/4
(T)
(F)
5
(RF_A)
(F)
(T)
(F)
(T)
B 3/4
(AD)
Servo DSP
2/2
B 2/4
D
E
8 9
B 3/4
1110
B 3/4
7
Spindle Drive IC
1/2
B 3/4
F
B 2/4
XV-DV1000
56
B 1/4
7
8
27
1234

3.6 DVDM ASSY (2/4)

A
B
C
B 2/4
DVDM ASSY (AWX8156)
VYW2060
PGM Flash Memory
B 1/4
B 3/4
B 1/4
B 1/4
B 3/4
B 3/4
B 1/4
B 1/4
B 3/4
B 3/4
B 3/4
B 4/4
D
E
F
B 1/4
B 2/4
28
B 1/4
B 1/4
B 3/4
FR CPU
B 4/4
B 1/4
B 3/4
B 3/4
B 1/4
B 1/4
B 4/4
B 4/4
B 1/4
B 4/4
B 4/4
1234
B 3/4
B 4/4
XV-DV1000
B 3/4
5678
Clock Generator
: The power supply is shown with the marked box.
B 3/4
(AD)
: AUDIO DATA SIGNAL ROUTE
B 4/4
B 3/4
B 3/4
B 3/4
B 1/4
B 4/4
B 3/4
A
B
C
B 3/4
B 1/4
(AD)
B 3/4
B 1/4
C
D 1/2
CN1002
D
B 4/4
E
CN901
B 3/4
(AD)
XV-DV1000
56
K 1/4
CN5505
F
B 2/4
7
8
29
1234

3.7 DVDM ASSY (3/4)

A
B 3/4
16M SDRAM
DVDM ASSY (AWX8156)
B 2/4, 3/4
B
B 4/4
(VD)
B 2/4
(AD)
B 2/4
B 2/4
C
B 2/4
(VD)
B 1/4
(AD)
(AD)
D
(AD)
(AD)
B 2/4
DVD Data Decoder
EBY-CHIP
(RF_V)
E
(RF_V)
B 1/4
(RF_V)
B 2/4
F
B 3/4
30
B 2/4
B 1/4
B 4/4
1234
XV-DV1000
B 1/4
B 1/4
B 1/4
Loading...
+ 137 hidden pages