Pioneer X-SMC3-K User Manual [en, es, fr]

X-SMC3

Slim AV Micro System Système AV Compact Sistema Micro Slim AV

Indoor Use Only Utiliser à l’intérieur seulement

Discover the benefits of registering your product online at

-K/-S

http://www.pioneer.co.uk (or http://www.pioneer.eu).

Découvrez les nombreux avantages offerts en enregistrant votre produit en ligne maintenant sur

http://www.pioneer.fr (ou http://www.pioneer.eu).

Registre su producto en http://www.pioneer.eu) Descubra los beneficios de registrarse on-line:

Operating Instructions Mode d’emploi Manual de instrucciones

http://www.pioneer.es (o en

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the AC adapter label.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c*_A1_En

When using this product, confirm the safety information shown on the bottom of the unit and the AC adapter label.

D3-4-2-2-4_B1_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

K041_A1_En

WARNING

Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems (Microwave ovens and Cordless phones, etc.). In this event noise appears in your television image, there is the possibility this unit (including products supported by this unit) is causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and this unit (including products supported by this unit).

• Pioneer is not responsible for any malfunction of the

compatible Pioneer product due to communication error/malfunctions associated with your network connection and/or your connected equipment. Please contact your Internet service provider or network device manufacturer.

• A separate contract with/payment to an Internet service provider is required to use the Internet.

Information for users on collection and disposal of old equipment and used batteries

Symbol for

equipment

Symbol examples

for batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

K058a_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

S002*_A1_En

CAUTION

STANDBY/ON switch on this unit will not

The completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

AC adapter CAUTION

• Make sure to grasp the body of the AC adapter when removing it from the power outlet. If you pull the power cord, it may become damaged which could lead to fire and/or electrocution.

• Do not attempt to plug in or remove the AC adapter with wet hands. This may result in electrocution.

• Do not insert the power cord of AC adapter into a power outlet where the connection remains loose despite inserting the prongs all the way into the outlet. Heat may be generated which could lead to fire. Consult with the retailer or an electrician regarding replacement of the power outlet.

Store the AC adapter out of the reach of children and infants.

The AC adapter cord may accidentally wind around the neck and it may cause suffocation.

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Loading the batteries in the remote control. . . . . . . . . . 5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . .5

02 Connections

Connecting the FM antenna . . . . . . . . . . . . . . . . . . . . . . 6

Connecting optional Bluetooth® adapter

(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting USB storage devices . . . . . . . . . . . . . . . . . . 6

Connecting your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting to the network through the LAN

interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connecting using LAN cable . . . . . . . . . . . . . . . . . . . . . . . 7

Connecting using wireless LAN . . . . . . . . . . . . . . . . . . . . . 7

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

03 Part names and functions

Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Top panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Main display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

04 Getting started 05 iPod/iPhone playback

Confirming what iPod/iPhone models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting your iPod/iPhone . . . . . . . . . . . . . . . . . . . . 14

Connecting your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Playing your iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . 15

06 Bluetooth®

Music playback using Bluetooth wireless

technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Remote control operation. . . . . . . . . . . . . . . . . . . . . . . . .17

Connecting optional Bluetooth® adapter . . . . . . . . . . 17

Setting the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Pairing Bluetooth® adapter and Bluetooth wireless

technology device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Listening to music contents of Bluetooth wireless

technology device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AIR JAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Audio playback (optional)

07 USB playback

Playing files stored on USB storage devices . . . . . . . . 20

08 Internet radio

Listening to the Internet radio. . . . . . . . . . . . . . . . . . . . 21

Connecting to a LAN network. . . . . . . . . . . . . . . . . . . . . . 21

Listening to the Internet radio for the first time . . . . . . .21

Tune into a station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Adding the stations to the Favorites. . . . . . . . . . . . . . . 22

To delete the stations from the list. . . . . . . . . . . . . . . . . .22

Advanced operations for the Internet radio . . . . . . . . . 22

Registering broadcast stations not on the vTuner list from

the special Pioneer site. . . . . . . . . . . . . . . . . . . . . . . . . . .22

09 Music server

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

About playable DLNA network devices . . . . . . . . . . . . . . 23

Using AirPlay on iPod touch, iPhone, iPad and

iTunes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

About the DHCP server function . . . . . . . . . . . . . . . . . . . 23

Authorizing this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Playing audio files stored on PCs or other

components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting to the LAN network. . . . . . . . . . . . . . . . . . . .24

Playback with Music Server . . . . . . . . . . . . . . . . . . . . . . . 24

10 Using the tuner

Listening to the FM radio broadcasts. . . . . . . . . . . . . . 25

Saving stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Listening to station presets. . . . . . . . . . . . . . . . . . . . . . 25

11 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . 26

Listening to auxiliary components . . . . . . . . . . . . . . . . 26

12 Changing the settings

Using the timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning on/off the wake-up timer. . . . . . . . . . . . . . . . . . . 29

Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . .29

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Wired Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Wireless Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

WPS connection setting . . . . . . . . . . . . . . . . . . . . . . . . 31

Connecting using PIN Input. . . . . . . . . . . . . . . . . . . . . . . 32

Friendly Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Parental lock setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Turn on/off the parental lock . . . . . . . . . . . . . . . . . . . . . . 32

Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Software Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Software Update messages . . . . . . . . . . . . . . . . . . . . . . . 33

Sound settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Using the Virtual Surround/Sound Retriever . . . . . . . . . 33

Adjusting the bass and treble . . . . . . . . . . . . . . . . . . . . .33

Resetting the system . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

13 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Playable file formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

About network playback . . . . . . . . . . . . . . . . . . . . . . . . 40

About iPod/iPhone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

About Wi-Fi® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

• Illustrations featured in the Operating Instructions may have been modified or simplified for ease of explanation, and may therefore differ from the actual product appearance.

Before you start 01

30°

7 m

30°

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box when you open it.

• Remote Control

•Power cord

•AC adapter

•FM wire antenna

• AAA batteries (R03) x 2

•Operating instructions (this document)

Loading the batteries in the remote control

1 Open the rear lid and load the batteries as illustrated below.

2 Close the rear lid.

The batteries included with the unit have been provided to allow you check product operation and may not last long. We recommend using alkaline batteries that have a longer life.

Caution

• When inserting the batteries, make sure not to damage the springs on the battery’s  terminals.

• Do not use any batteries other than the ones specified. Also, do not use a new battery together with an old one.

• When loading the batteries into the remote control, set them in the proper direction, as indicated by the polarity marks ( and ).

• Do not heat batteries, disassemble them, or throw them into flames or water.

•Batteries may have different voltages, even if they are the same size and shape. Do not use different types of batteries to

•To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.

• WARNING Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This ca explode or catch fire. It can also reduce the life or performance of batteries.

gether.

n cause batteries to leak, overheat,

Using the remote control

The remote has a range of about 7 m at an angle of about 30º from the remote sensor.

Keep in mind the following when using the remote control:

•Make sure that there are no obstacles between the remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor.

• Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit.

•Replace the batteries when you notice a fall off in the operating range of the remote.

English

Français Español

Connections02

Note

FM wire antenna (supplied)

This unit’s rear panel

Bluetooth® adapter

(commercially available)

This unit’s rear panel

Cover

USB storage device (commercially available)

This unit’s front panel

Yellow

Video cable

(commercially available)

To video input terminals

This unit’s rear panel

Chapter 2:

Connections

•Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.

• Connect the power cord after all the connections between devices have been completed.

Connecting the FM antenna

Connect the FM antenna plug onto the center pin of the FM antenna socket.

Connecting optional (optional)

Connect the Bluetooth® adapter (Pioneer Model No. AS-BT200) to AS-BT200 terminal on the rear panel.

•Open the AS-BT200 terminal’s cover and connect the

Bluetooth

then close the cover.

ANTENNA

LAN

VIDEO

FM75

(10/100)

Bluetooth

adapter with the label side facing to the right,

DC IN

OUT

19 V

adapter

Connecting USB storage devices

Connecting your TV

To watch iPod/iPhone images on a television, connect it using a composite video cable.

• When an iPod/iPhone is connected to this unit, the TV output setting of the iPod/iPhone is automatically set to

‘ON’.

ANTENNA

LAN

VIDEO

FM75

(10/100)

DC IN

OUT

19 V

1To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit. 2 • Some iPod allow the TV output setting to be changed while connected.

• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state.

Connections 02

Note

Internet

Modem

Router

PC2

PC1

This unit’s rear panel

LAN cable

(commercially

available)

Internet

This unit

Router

Modem

Connecting to the network through the LAN interface

By connecting this unit to the network via the LAN interface, you can play back audio files stored on components on the network, including your PC, and listen to Internet radio

stations. Connect the LAN terminal on this unit to the LAN terminal on

your router (with or without the built-in DHCP server function) with a straight LAN cable (CAT 5 or higher). Also wireless connection to the network is possible.

Turn on the DHCP server function of your router. If your router does not have a built-in DHCP server function, you have to set up the network manually. For details, see page 29.

Connecting using LAN cable

LAN

321

ANTENNA

LAN

(10/100)

VIDEO

OUT

FM75

Connecting using wireless LAN

English

Français Español

LAN

321

WAN

DC IN

19 V

WAN

1• In order to connect to the Internet, you must conclude a contract with an Internet Service Provider (ISP).

• To listen to Internet radio stations, you must sign a contract with an ISP (Internet Service Provider) beforehand.

• Photo or video files cannot be played back.

• With Windows Media Player 11or 12, you can even play back copyrighted audio files on this unit.

Connections02

To AC outlet

AC adapter (supplied)

This unit’s rear panel

Power code (supplied)

Plugging in

Important

•Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

After you’ve finished making all connections, plug the unit into an AC outlet.

ANTENNA

LAN

VIDEO

(10/100)

DC IN

OUT

19 V

FM75

1 Plug the supplied AC adapter into the socket on the back of the unit.

2 Plug the supplied power cord into the AC adapter then plug the other end into an AC outlet.

DC IN

Part names and functions 03

Note

Chapter 3:

Part names and functions

STANDBY/ON

Remote control

STANDBY/ON

1 2

Press to turn the power on and off.

2DISP OFF

Press to turn the display off when you do not need it.

3 Number buttons (0 to 9)

Use them to select the station preset when using the tuner, etc.

4 SET UP

Use this to change the settings such as Timer Setting (page 27), Clock Setting (page 27), Display Setting (page 27), Network Setting (page 27), Option Setting (page 28) and see System Info (page 28).

5MENU

Select and play the track or file from the menu screen.

6 ///

Use these to select items, change settings and move the cursor.

ENTER

Use this to implement the selected item or enter a setting that you have changed.

PRESET +/–

Use these to select station presets.

TUNE +/–

Change the frequency one step at a time. To search for stations automatically, press and hold for about a few second.

SOUND

Turns Virtual Surround and Sound Retriever on and off (page 33). Also use to adjust the Bass and Treble.

FUNCTION /

Use to change the input source. The source changes as below.

iPod  BT Audio Internet Radio  Music Server  AUX  Return to the

beginning (Undisplayed)

 PLAY

Press to start playback.

10 

Press during playback to fast-reverse.

 Air Jam1  USB  FM 

English

Français Español

1Optionally available. To use BT Audio and Air Jam function, you need to connect the commercially available

AS-BT200 to the unit. See page 17 for details.

Bluetooth

adapter:

Part names and functions03

Note

 PREV

Press to return to the beginning of the currently playing track or file. Press twice to move back to the beginning of the previous track or file.

 STOP

Press to stop playback.

SLEEP

Use to put the unit in the sleep mode and select the amount of time before sleep (page 29).

Use to turn on and off the timer (page 28).

CLEAR

Press to clear the selected item. Use this for example if you input the wrong number.

RETURN

Press to return to the previous screen. Also, use to cancel the clock setting or the sound setting.

Top panel

1 4

2 3

MUTE

Press to temporarily silence the sound.

SHUFFLE

Perform shuffle play of tracks on the selected iPod/iPhone, USB storage device or Music Server (page 15, 20, 24).

VOLUME +/–

Use to set the listening volume. (Default setting: 10)

REPEAT

Perform repeat play of tracks on the selected iPod/iPhone, USB storage device or Music Server (page 15, 20, 24).



Press during playback to fast-forward.

22

PAUSE

Press to stop playback temporarily. Press again to resume.

 NEXT

Press during playback to skip ahead to the beginning of the next track or file.

 STANDBY/ON

Press to turn the power on and off.

2FUNCTION

Use to change the input source. The source changes as below.

iPod  BT Audio Radio  Music Server  AUX  Return to the beginning

(Undisplayed)

BT AUDIO

Switches the input source to Bluetooth® Audio.

1Optionally available. To use BT Audio and Air Jam function, you need to connect the commercially available

AS-BT200 to the unit. See page 17 for details.

 Air Jam1  USB  FM  Internet

AIR JAM

Switches the input source to Air Jam.



Press to start playback. During playback, pause/unpause playback.



Press to stop playback.

VOLUME –/+

Use to set the listening volume. (Default setting: 10)

Bluetooth

adapter:

Part names and functions 03

Note

Front panel

POWER ON

When the power is on, this indicator lights.

BT AUDIO

When BT Audio is selected as the input source, this indicator lights.

AIR JAM

When Air Jam is selected as the input source, this indicator lights.

TIMER

When the wake-up timer is set to On, this indicator lights.

TUNE

When the tuner receives FM broadcasts, the TUNE indicator lights.

English

Français Español

Main Display

Sub Display

Speaker units

USB port

AUX IN

Use to connect auxiliary components.

7PHONES

Use to connect headphones.

iPod/iPhone connector port

1Optionally available. To use BT Audio and Air Jam function, you need to connect the commercially available

AS-BT200 to the unit. See page 17 for details.

Bluetooth

adapter:

Part names and functions03

Song 1 Artist Album

1 4

2 3

10 11 12

Main display

1 Input source

2 Sleep timer

When the sleep timer is set, the remaining time until power off is displayed.

3 AirPlay

This appears in blue during AirPlay operation, and in white during stop mode.

4 Network connection status

When the unit is connected to the wired network, this indicator lights.

When the unit is connected to the wireless network, this indicator lights.

When the unit is not connected to the network, this indicator lights.

5 Name of folder/file/track/artist/album/ station, etc.

6Mute

Displayed during Mute operation.

7 Play status

8 Artwork

Displayed when the currently playing file includes an album jacket image, etc.

9 Repeat and Shuffle

Repeat all files.

Repeat a file.

Shuffle

10 Elapsed playing time

11 Play bar

The bar becomes longer together with the elapsed playback time.

12 Remaining playing time

Getting started 04

Select "Start" to start Demo mode; otherwise "Cancel".

[PLAY] Start

[STOP] Cancel

Language

Français

Deutsch Nederlands

English

Chapter 4:

Getting started

When you use the unit for the first time, the following screens will be displayed.

Set up the following items to customize the unit.

1 Press

About twenty seconds after turning on the power, the following splash screen appears. About one minute is required between turning the power on and completion of startup.

Setting Quick Start Mode to On will allow faster startup (page 28).

2Use  STOP

The screen below will automatically appear after the screen in step 1.

STANDBY/ON

 PLAY

to deactivate Demo Mode.

• Demo Mode also can be activated in Auto mode select (page 28).

to activate Demo Mode or use

3Use

/

this unit, then press

The setting is done.

to select the menu language of

ENTER

English

Français Español

• When Start is selected, the demo mode operates. When starting up the next time, it will be necessary to set step

•If Cancel is selected, operation will automatically proceed to step 3.

iPod/iPhone playback05

Note

Push

Chapter 5:

iPod/iPhone playback

Merely by connecting your iPod/iPhone to this unit, you can enjoy high-quality sound from your iPod/iPhone. This unit can also be connected to a television set, letting you view images from your iPod/iPhone.

Playback and volume level setting for iPod/iPhone music and images can be performed from this unit or the iPod/iPhone itself.

Tip

• When using an iPod/iPhone not supported by this unit, use a commercially available cable to connect the iPod/ iPhone to the AUX IN connector of this unit.

Connecting your iPod/iPhone

Confirming what iPod/iPhone models are supported

The iPod/iPhone playable on this unit are shown below.1

iPod/iPhone Audio Control Video

iPod nano 2G 

iPod nano 3/4/5/6G 

iPod classic 

iPod touch 1/2/3/4G 

iPhone 

iPhone 3G/3GS 

iPhone 4 

* The iPod nano 6G cannot play back video, but can play slide

shows only.

• This system has been developed and tested for the software version of iPod/iPhone indicated on the website of Pioneer (http://pioneer.jp/homeav/support/ios/ eu/).

• Installing software versions other than those indicated on the website of Pioneer to your iPod/iPhone may result in incompatibility with this system.

1 Select “

When using iPod touch or iPhone, select “General” after selecting “Settings”.

2 Select “

The software version will be displayed.

Settings

About

” from the top menu.

”.

—



Caution

• When connecting iPod/iPhone units, always use the dock adapter provided with iPod/iPhone units, or a commercially available adapter designed to support iPod/iPhone. The iPod/iPhone cannot be connected without a dock adapter; attempting to connect an iPod/ iPhone without it will cause damage or malfunction.

• An iPod/iPhone universal dock adapter is not supplied with this unit.

1 Open the iPod/iPhone connector port.

2 Attach the dock adapter to iPod/iPhone connector port.

When attaching the dock adapter, be sure to orient the front- back directions of the dock adapter correctly. To attach, first place the protruding tabs on the front side of the adapter into the depressions on the iPod/iPhone connector port and press into position. When attaching the adapter, be careful not to strike the connectors.

1 • Pioneer does not guarantee that this unit plays iPod/iPhone models other than the ones specified.

• Some functions may be restricted depending on the model or software version.

• iPod/iPhone is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.

• Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizer off before connecting.

• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience or loss of recorded material resulting from iPod/iPhone failure.

• For detailed instructions on using the iPod/iPhone, please refer to the manual supplied with the iPod/iPhone.

2 When opening or closing the iPod/iPhone connector port, support the top of the unit with your hand to prevent it from moving.

iPod/iPhone playback 05

Note

Push

3 Connect your iPod/iPhone.





• When your iPod/iPhone is not connected to the unit, close the iPod/iPhone connector port firmly.

Connecting your TV

To watch iPod/iPhone images on a television, connect it using a composite video cable.

• When an iPod/iPhone is connected to this unit, the TV output setting of the iPod/iPhone is automatically set to

‘ON’.

Playing your iPod/iPhone

Caution

• When your iPod/iPhone is connected to this unit and you wish to operate the iPod/iPhone directly, be sure to hold the iPod/iPhone steady with the other hand to prevent malfunctions due to faulty contacts.

1 Connect your iPod/iPhone.

• To connect your iPod/iPhone, see Connecting your iPod/ iPhone on page 14.

2 Press input source.

iPod is shown on the main display and starts playback.

The following operations are possible for iPod/iPhone.

Button What it does

 PLAY

 PAUSE

 STOP

 PREV

 NEXT





SHUFFLE

REPEAT

//ENTER

When no device is connected to the iPod/iPhone connector port and this unit is not operated for 30 minutes or more, power will automatically turn off.

FUNCTION /

Starts normal playback.

Pauses playback.

Press to skip to the start of the current file, then previous files.

Press to skip to the next file.

Press and hold to start fast reverse scanning.

Press and hold to start fast forward scanning.

The currently selected iPod/iPhone tracks are played back in random order (shuffle play).

The currently selected iPod/iPhone tracks are played back repeatedly.

Use to access the iPod/iPhone menu.

Use to control the iPod/iPhone menu.

Each time you press REPEAT the repeat modes changes as

below.

Repeat 1  Repeat all  Normal playback Repeat 1: Repeats a file currently played back. Repeat all: Repeats all files.

to select

iPod

as the

English

Français Español

1 • Some iPod allow the TV output setting to be changed while connected.

• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state. 2 No icon will be displayed on the main display when the unit is in the repeat mode or shuffle mode. 3Only when Power Save mode is selected in Auto mode select (page 28).

iPod/iPhone playback05

Important

If this unit cannot play your iPod/iPhone, perform the following troubleshooting checks:

• Check whether the iPod/iPhone is supported by this unit.

• Reconnect the iPod/iPhone to the unit. If this doesn’t seem to work, try resetting your iPod/iPhone.

• Check the iPod/iPhone software is supported by this unit.

If the iPod/iPhone cannot be operated, check the following items:

• Is the iPod/iPhone connected correctly? Reconnect the iPod/iPhone to the unit.

• Is the iPod/iPhone experiencing a hangup? Try resetting the iPod/iPhone, and reconnect it to the unit.

Tip

• iPod/iPhone recharging occurs whenever an iPod/ iPhone is connected to this unit. (This function is supported in standby mode as well.)

• When input is switched from iPod to another function, the iPod/iPhone’s power will be turned off automatically.

• If the unit is set to standby when an iPod/iPhone is connected, the iPod/iPhone will be turned off automatically.

Bluetooth

Remote control operation

This unit

Bluetooth

adapter

Device not equipped with Bluetooth

wireless technology: Digital music player

Bluetooth® audio transmitter

(commercially available)

Bluetooth wireless technology

enabled device:

Digital music player

Bluetooth wireless technology

enabled device:

Cell phone

Note

Bluetooth® adapter

(commercially

available)

This unit’s rear panel

Cover

Audio playback (optional)

Chapter 6:

Bluetooth

Music playback using

Audio playback

Bluetooth

wireless

technology

When the Bluetooth® adapter (Pioneer Model No. AS-BT200) is connected to this unit, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music wirelessly. a commercially available transmitter supporting Bluetooth wireless technology, you can listen to music on a device not equipped with Bluetooth wireless technology. The AS-BT200 model supports SCMS-T contents protection, so music can also be enjoyed on devices equipped with SCMS-T type Bluetooth wireless technology.

Also, by using

(optional)

Connecting optional

1 Connect the

Bluetooth

Bluetooth® adapter to the unit

when the unit is in standby mode.

• Remove the AS-BT200 terminal’s cover and connect the

Bluetooth

then close the cover.

adapter with the label side facing to the right,

adapter

English

Français Español

Remote control operation

The remote control supplied with this unit allows you to play and stop media, and perform other operations.

1• The Bluetooth wireless technology enabled device must support A2DP profiles.

2• The Bluetooth wireless technology enabled device must support AVRCP profiles.

• Pioneer does not guarantee proper connection and operation of this unit with all

• The CORPORATION is under license. Other trademarks and trade names are those of their respective owners.

• Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.

Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth

wireless technology enabled devices.

Bluetooth

SIG, Inc. and any use of such marks by PIONEER

Note

Option Setting

Volume Limit Setting

Internet Parental Lock Auto mode select

BT PIN Select

Bluetooth

Audio playback (optional)

2 Press

3 Press top panel of the unit to select

input source.

The BT AUDIO indicator lights and BT Audio is shown on the main display.

STANDBY/ON

FUNCTION /

to turn the power on.

BT AUDIO

on the

as the

Setting the PIN code

Set this unit’s PIN code to the same setting as that for the Bluetooth wireless technology device used. Supported PIN code setting values include 0000, 1234 or 8888.

• Default setting: 0000

1 Press top panel of the unit to select input source.

The BT AUDIO indicator lights and BT Audio is shown on the main display.

2 Press

3Use Select, then press

4Use ENTER

The PIN code is stored.

FUNCTION /

BT AUDIO

BT Audio

SET UP

/

to select Option Setting  BT PIN

ENTER

/

to select the PIN code, then press

on the

as the

Pairing

Bluetooth

“Pairing” must be done before you start playback of Bluetooth wireless technology content using Bluetooth sure to pair devices the first time you operate the system or any time pairing data is cleared. “Pairing” is the step necessary to register Bluetooth wireless technology device to enable Bluetooth communications. also the operating instructions of your Bluetooth wireless technology device.

1Press

Bluetooth

wireless technology device

FUNCTION /

top panel of the unit to select

adapter and

For more details, see

BT AUDIO

BT Audio

adapter. Make

on the

as the

input source.

The BT AUDIO indicator lights and BT Audio is shown on the main display.

2 Turn on the

Bluetooth

wireless technology device that you want to pair, place it near the system and set it into pairing mode.

Pairing starts.

3 Check to see that the detected by the device.

•If the Bluetooth wireless technology device cannot be connected to the unit, perform the connection operation from the Bluetooth wireless technology device.

Bluetooth

Listening to music contents of

Bluetooth® adapter is

wireless technology

Bluetooth

wireless technology device

1Press top panel of the unit to select input source.

The BT AUDIO indicator lights and BT Audio is shown on the main display.

2 Make connection between the wireless technology device and the unit.

FUNCTION /

BT AUDIO

BT Audio

on the

as the

Bluetooth

• See Pairing Bluetooth® adapter and Bluetooth wireless technology device above.

1 When the Bluetooth® adapter is not connected and BT Audio is selected as the input source, the error message BT Adapter Not

Connected will be shown on the main display.

2 • Pairing is required when you first use Bluetooth wireless technology device and Bluetooth® adapter.

• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology device.

Bluetooth

Note

Audio playback (optional)

3 Press

The following operations are now possible for Bluetooth wireless technology devices, using the remote control.

Button What it does

 PLAY

 PAUSE

 STOP

 PREV

 NEXT





* This function may work differently depending on the connected

 PLAY

to start playback.

Starts normal playback.

Pauses playback.

Stops playback.

Press to skip to the start of the current file, then previous files.

Press to skip to the next file.

Press and hold to start fast reverse scanning.

Press and hold to start fast forward scanning.

device.

• When no Bluetooth wireless technology device is connected and no operation has been done for 30 minutes or more, the power will automatically turn off.

AIR JAM

Air Jam – a Pioneer-exclusive application and available for free.

Air Jam lets you connect multi compatible devices to this unit using Bluetooth wireless technology. With it, you can make a group playlist directly on a supported device to play in your home theater through the unit. You and your friends can add songs from your devices to the playlist. Also Air Jam lets you delete the song before anyone has to hear it.

1 Press panel of the unit to select source.

The AIR JAM indicator lights and Air Jam is shown on the main display.

For more details on using Air Jam, access our website.

http://pioneer.jp/product/soft/iapp_airjam/en.html

FUNCTION /

AIR JAM

on the top

as the input

English

Français Español

1• The Bluetooth wireless technology enabled device must support AVRCP profiles.

• The operation of some Bluetooth wireless technology devices may differ from what is shown in the above table.

2Only when Power Save mode is selected in Auto mode select (page 28).

USB playback07

Note

Song 1 Artist Album

Chapter 7:

USB playback

Playing files stored on USB storage devices

• This unit may not recognize a USB storage device, play files or supply power to a USB storage device. For details, see When a USB storage device is connected on page 35.

• Pioneer does not guarantee that any file recorded on a USB storage device will play or that power will be supplied to a USB storage device. Also note that Pioneer will accept no responsibility whatsoever for loss of files on USB storage devices caused by connection to this unit.

1 Press input source.

USB is shown on the main display.

2 Connect the USB storage device.

The folders/files stored on the connected USB storage device appear on the main display automatically.

3Use / to select the file, then press ENTER

Playback starts.

You can perform the following operations. Note that some buttons are not available for operation depending on the category currently being played back.

Button What it does

 PLAY

 PAUSE

 STOP

 PREV

 NEXT

SHUFFLE

REPEAT

*Press repeatedly to switch between repeat play options. ‘ ’

1Only when Power Save mode is selected in Auto mode select (page 28).

FUNCTION /

to select USB as the

•To return to the previous screen, press RETURN.

•Turn the power off before removing the USB storage device.

Unpauses playback.

Pauses playback.

Stops playback.

Press to skip to the previous files.

Press to skip to the next file.

The currently selected tracks are played back in random order (shuffle play).

The currently selected tracks are played back

repeatedly.

plays the currently playing file repeatedly. ‘ ’ plays all the files repeatedly.

When a USB storage device is not playing and the unit has not been operated for 30 minutes or more, the power will automatically turn off.

The following screen appears on the main display when you play back audio files. Note that some file types may not be displayed.

Internet radio 08

Internet Radio

Find Net Radio

Favorites

Genres

Countries

Podcasts By Genre Podcasts By Location

Chapter 8:

Internet radio

Listening to the Internet radio

Connecting to a LAN network

Connect to the network using the LAN interface. For details on the connections, see Connecting to the network

through the LAN interface on page 7.

Listening to the Internet radio for the first time

When you listen to the Internet radio first time, follow the instructions below to tune into your desired station.

1 Press Radio as the input source.

Internet Radio is shown on the main display.

2Use ENTER

FUNCTION /

/

to select Find Net Radio, then press

to select Internet

3Use

/

ENTER

to select the station, then press

Tune into a station

1 Press Radio as the input source.

2 Press menu screen.

3Use Favorites

4Use ENTER

FUNCTION /

•The information of the station you last selected is displayed on the main display.

to display the internet radio

/

to select

, then press

• Select Find Net Radio when you want to tune into a station which has not been added to Favorites.

• Select Favorites when you want to tune into a station which has been added to Favorites already.

• To add stations to the Favorites, see Adding the stations to the Favorites on page 22.

/

to select the station, then press

• When you select Find Net Radio, you can also select the available stations from the Internet radio menu.

to select Internet

Find Net Radio

ENTER

English

Français Español

Internet radio08

Adding the stations to the Favorites

1 Tune into the station from Find Net Radio.

• Follow the instructions Tune into a station on page 21.

•The information of the station is displayed on the main display.

2 Press and hold

1. FM AAAAA

[ENTER] (Press and hold): Add to Favorites

To delete the stations from the list

1 Press menu screen.

2Use ENTER

3Use delete, then press

4Use

Select OK to confirm.

/

• To cancel deleting the station, press RETURN.

ENTER

for a few seconds.

to display the internet radio

to select

Favorites

, then press

to select the station you want to

ENTER

to select Delete, then press

ENTER

Advanced operations for the Internet radio

Registering broadcast stations not on the vTuner list from the special Pioneer site

With this unit, broadcast stations not included on the list of stations distributed by vTuner can be registered and played. Check the access code required for registration on this unit, use this access code to access the special Pioneer Internet radio site and register the desired broadcast stations in your favorites. The address of the special Pioneer Internet radio site is:

http://www.radio-pioneer.com

1Display

To display the Internet radio list screen, perform steps 1 to 3 at Listening to the Internet radio for the first time on page 21.

2Use

3Use press

The access code required for registration on the special Pioneer Internet radio site is displayed. Make a memo of this address.

The following can be checked on the Help screen:

• Get access code

• Show Your WebID/PW

• Reset Your WebID/PW

4 Access the special Pioneer Internet radio site from your computer and perform the registration process.

Access the above site and use the access code in step 3 to perform user registration, following the instructions on the screen.

5 Register the desired broadcast stations as your favorites, following the instructions on the computer’s screen.

Both broadcast stations not on the vTuner list and stations on the vTuner list can be registered. In this case they are registered on the unit as favorite broadcast stations and can be played.

Find Net Radio

/

to select

/

to select

ENTER

registration on the special Pioneer Internet radio site is displayed.

special Pioneer Internet radio site, the registered ID and

password are displayed.

registered on the special Pioneer Internet radio site.

When reset, all the registered broadcast stations are also cleared. If you want to listen to the same stations, re- register after resetting.

The access code required for

screen.

Help

, then press

Get access code

After registering on the

Resets all the information

ENTER

, then

Music server 09

Note

Chapter 9:

Music server

This unit can play audio files stored on PCs or other components on a Local Area Network (LAN).

Introduction

This unit allows you to listen to audio files or listen to Internet radio stations on a computer or other component connected

to the unit via LAN interface. This chapter describes the setup and playback procedures required to enjoy these features. It is advisory that you also refer to the operation manual supplied with your network component.

•Photo or video files cannot be played back.

• With Windows Media Player 11 or Windows Media Player 12, you can even play back copyrighted audio files on this unit.

About playable DLNA network devices

This unit allows you to play music on media servers connected on an identical Local Area Network (LAN) as the unit. This unit allows you to play files stored on the following devices:

•PCs running Microsoft Windows Vista or XP with Windows Media Player 11 installed

•PCs running Microsoft Windows 7 with Windows Media Player 12 installed

•DLNA-compatible digital media servers (on PCs or other components)

Files stored in a PC or DMS (Digital Media Server) as described above can be played via command from an external Digital Media Controller (DMC). Devices controlled by this DMC to play files are called DMRs (Digital Media Renderers). This unit supports this DMR function. When in the DMR mode, such operations as playing and stopping files can be performed from t and the muting control are also possible. The DMR mode is canceled if the remote control unit is operated while in the DMR mode (aside from certain buttons, including the VOLUME +/–, MUTE and DISP OFF).

•Depending on the external controller being used, playback may be interrupted when the volume is adjusted from the controller. In this case, adjust the volume from the unit or remote control.

Using AirPlay on iPod touch, iPhone, iPad and iTunes

This unit supports AirPlay audio streaming from iPod touch (2nd, 3rd and 4th generations), iPhone 4, iPhone 3GS, iPad with iOS 4.2 or later, and iTunes 10.1 (Mac and PC) or later.

he external controller. Volume adjustment

To use AirPlay, select your unit on your iPod touch, iPhone, iPad or in iTunes and start playback.

Input to the unit will switch automatically when AirPlay is in use.

The following operations can be performed when in AirPlay mode:

• Adjustment of the unit’s volume from iPod touch, iPhone, iPad or iTunes.

•Pause/resume, next/previous track, and shuffle/repeat from the remote control of the unit.

•Display of the currently playing track information on the unit’s main display, including artist, song/album name and album artwork.

Tip

•A network environment is required to use AirPlay.

• The unit’s name that shows up in the AirPlay UI on iPod touch, iPhone, iPad and iTunes can be changed by Friendly Name from Network Setting.

•AirPlay provided on this unit has been developed and tested based on the software versions for the iPod touch, iPhone, iPad and the software versions for iTunes that are indicated on the Pioneer website. AirPlay may not be compatible with iPod touch, iPhone, iPad or iTunes software versions other than those indicated on the Pioneer website.

About the DHCP server function

To play back audio files stored on components on the network, you must turn on the DHCP server function of your router.

In case your router does not have the built-in DHCP server function, it is necessary to set up the network manually. Otherwise, you cannot play back audio files stored on components on the network or listen to Internet radio stations. See Network setting on page 29 for more on this.

Authorizing this unit

This unit must be authorized to enable playback. The unit is automatically authorized when it is connected to a PC over a network. If not, please authorize this unit manually on the PC. The authorization (or permission) method for access varies depending on the type of server currently being connected. For more information on authorizing this unit, refer to the instruction manual of your server.

English

Français Español

1For more information, see the Apple website (http://www.apple.com). 2 It may not be displayed other than song name.

Music server09

Playing audio files stored on PCs or other components

Connecting to the LAN network

Be sure to connect PC or other components to the network using the LAN interface before you use this function.

For details on the connections, see page 7.

Playback with Music Server

Important

• You cannot access a PC on a network while you are logged onto a domain that is configured in a Windows network environment. Instead of logging onto the domain, log onto the local machine.

•There are cases where the time elapsed may not be correctly displayed.

1 Press

All available servers are shown on the main display.

2Use you want to play is stored on, then press

The folders/files stored on the server are shown on the main display.

3Use then press ENTER.

Playback starts.

FUNCTION /

• When no sever is available to play, “Empty” will be displayed.

/

to select the server that the file

to select Music Server.

ENTER

/

to select the file you want to play,

You can perform the following operations. Note that some buttons are not available for operation depending on the category currently being played back.

Button What it does

 PLAY

 PAUSE

 STOP

 PREV

 NEXT

SHUFFLE

REPEAT

*Press repeatedly to switch between repeat play options. ‘ ’

plays the currently playing file repeatedly. ‘ ’ plays all the files repeatedly.

Unpauses playback.

Pauses playback.

Stops playback.

Press to skip to the previous file.

Press to skip to the next file.

The currently selected tracks are played back in random order (shuffle play).

The currently selected tracks are played back

repeatedly.

Song 1 Artist Album

• When the file you want to play is in the folder, select the folder first.

•If you press RETURN during playback, the previous (folders/files) screen will be displayed.

Using the tuner 10

Note

Chapter 10:

Using the tuner

Listening to the FM radio broadcasts

The tuner can receive FM broadcasts, and can save your favorite stations.

1 Press

The tuned frequency will be displayed on the main display.

2 Tune into a station.

When the tuner receives FM broadcasts, the TUNE indicator lights.

There are two ways to do this:

Saving stations

You can save up to 9 station presets so that you always have easy access to your favorite stations without having to tune in manually each time.

• Manually saving station presets

1 Press

The tuned frequency will be shown on the main display.

2 Tune into a station.

3 Press and hold a number button (1 to 9) for a few seconds.

The tuned frequency is preset to the selected number button. The previous station preset is overwritten.

• Automatically saving station presets

1 Press and hold

Auto tuning starts.

FUNCTION /

Automatic tuning - To search for stations, press and

TUNE +/– for about a few seconds. This unit will

hold start searching for the next station, stopping when it has found one. Repeat to search for other stations.

Manual tuning - To change the frequency one step at

a time, press TUNE +/–.

FUNCTION /

• The tuned frequencies will be preset to the buttons in numerical order.

• Auto tuning stops after the FM band has finished, or the limit of 9 presets has been reached.

to select FM.

PRESET +

for a few seconds.

Listening to station presets

1 Press

The tuned frequency will be shown on the main display.

2 Press the number button (1 to 9) that stores the FM radio station.

FUNCTION /

Tip

• Press PRESET +/– repeatedly to selected the station preset in numerical order.

to select FM.

English

Français Español

1 When a new broadcast frequency is stored in a station containing a previously stored frequency, the previous frequency will be overwrit-

ten with the new one.

Other connections11

Digital audio player, etc.

Stereo mini-plug cable (commercially available)

This unit’s front panel

Chapter 11:

Other connections

•Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet.

•If the AUX IN mini-plug jack is connected to auxiliary phones jack, the volume of the unit will be adjusted by the volume on the playback component. If the sound is distorted after you lower the volume of the unit, try lowering the volume on the auxiliary playback component.

Connecting auxiliary components

Connect the front panel AUX IN mini-plug jack to your auxiliary playback component.

• This method can be used to play music on this unit from iPods/iPhones that do not support use of an iPod Dock.

Listening to auxiliary components

1Press

2 Start playback of the auxiliary component.

FUNCTION /

• AUX is shown on the main display.

to select AUX.

Changing the settings 12

Chapter 12:

Changing the settings

The factory default settings are indicated in italic.

1 Press 2Use 3 Follow the descriptions on the main display to change the setting.

Settings What it does

Timer Setting

Display Setting (Level3/Level2/Level1)

SET UP

/

to select the item, then press

Clock Setting

Clock Display (On/On (Standby)/Off)

Time Format (12H/24H)

Clock Adjustment (Auto/Manual)

Time Zone

Default setting is

Daylight Saving Time (On/Off)

Network Setting

Network Type (Wired/Wireless/Auto)

Network Configuration (Wired Setting/Wireless Setting)

WPS (PBC/PIN Input)

Friendly Name

to show the

GMT ±0

Initial Setup

Setting the wake-up timer and the time the unit will be turned on.

• Select On to show clock on the sub display.

•When On (Standby) is selected, the clock will appear in the sub-display even when the power is set to Off.

Select the 12-hour (

• Select Auto to adjust the clock automatically.

• Select Manual to adjust the clock manually. How to adjust the clock, see page 28.

Select the time zone of your area. Time Zone can be adjusted only when

Auto

e.g. If you are in Hawaii (GMT -10:00), use

Select On when daylight saving time is in effect. The time advances 1 hour.

Dims or brightens the display.

Select the network connection type. When

Auto

is depending on the occasion when the unit is powered on.

For details on settings, see page 29.

WPS connection settings, see page 31.

The name of this system displayed on a computer or other device connected to the network can be changed.

screen.

ENTER

12H)

clock or 24-hour (

is selected, the network type is automatically switched between

24H

) clock.

/

to select Hawaii and press

Clock Adjustment

ENTER

Wired

and

Wireless

English

Français Español

is set to

. It

Changing the settings12

Note

Settings What it does

Option Setting

BT PIN Select (0000/1234/8888)

Volume Limit Setting (On/Off)

Internet Parental Lock (Change Password/Internet Parental Lock)

Auto mode select (Power Save mode/Demo Mode/Off)

Language

(English/Other languages)

Quick Start Mode (On/Off)

Software Update

System Info

Using the timer

Setting the clock

Setting the clock before using the timer.

1 Press

The Initial Setup screen is displayed on the main display.

2 Select Clock Setting  Clock Adjustment. 3 Select

If you select Manual, go to step 4.

SET UP

Auto

Manual

• Auto works only when this unit is connected to the network. Connect to the network if you want to use automatic time adjustment.

Use this to set the

When On is selected, the volume can be set between 0 to 30. Each time this setting has been changed, the volume becomes to 0.

Restricts usage of internet radio using password. Select You can set up the password from

When operation has done for more than 30 minutes. When

Demo Mode

than 5 minutes.

Change the language of the operation messages displayed on the main display. Other languages: French, German, Netherlands, Italian, Spanish, Russian, Japanese

When this is set to On, the time required for bootup will be shortened. In addition, power-on will occur simultaneously when AirPlay is performed. Note, however, that when to On, the electrical current consumed in the power-off (standby) mode will be about the same as that required when the power is turned on. Also, if the power cord is disconnected while

Mode

is set to On, the next time the plug is reconnected, about one minute warm-up will be required

before the unit responds. Wait for one minute after reconnecting the cord before pressing

STANDBY/ON

Use this to update unit software.

Use this to check unit information details.

Bluetooth

Power Save mode

is selected, the demons tration screen will start if no operation has done for more

PIN code. (page 18)

Change Password

is selected, the unit will be automatically in the standby mode if no

4Use the clock, then press

•Using / moves the adjusting digit (hour/minute/ second/AM, PM

•Using / increases or decreases values.

Internet Parental Lock

. (page 32)

///

or number buttons to adjust

ENTER

to On/

Quick Start Mode

Off

Quick Start

Clock Adjustment

2 21 0 AM

H:M:S AM/PM

is set

•If you press RETURN, the previous screen will be displayed.

Setting the wake-up timer

1Press

The Initial Setup screen is displayed on the main display.

1 You’ll need to set the clock again if you unplug the unit (or in case of a power failure). 2 The “AM” and “PM” indicators appear only when the Time Format is set to the 12H mode. 3 When the unit is in iPod, FM, Internet Radio, or Aux modes, you can set the timer.

SET UP

Changing the settings 12

Note

2 Select Timer Setting.

The Timer Setting screen is displayed.

3Use

///

the clock, then press

The TIMER indicator lights and the wake-up timer has been set.

•Using / moves the adjusting digit (hour/minute/

•Using / increases or decreases values.

AM, PM

or number buttons to adjust

ENTER

Timer Setting

7 0 AM

H:M AM/PM

•If you press RETURN, the previous screen will be displayed.

•The wake-up timer will turn on an input source at the volume level you selected when you set the timer.

Turning on/off the wake-up timer

1 Press to turn on the timer.

The TIMER indicator lights.

•To turn off the timer, press during the timer is on.

Using the wake-up timer

1 Set the wake-up timer to on.

2 Press

STANDBY/ON

to turn the power off.

3 At the wake-up time, this unit will turn on automatically and play the selected input function.

If this unit is not operated for 60 minutes or more after playback is started by the wake-up timer, power will automatically turn off (standby mode).

Using the sleep timer

The sleep timer switches off the unit after a specified time so you can fall asleep without worrying about it.

1 Press SLEEP repeatedly to select a switch off time.

Choose between 5 min, 15 min, 30 min, 60 min, 90 min or Off.

Network setting

If a broadband router (with built-in DHCP server function) is connected to this unit, you can simply turn on the DHCP server function without having to set up the network manually. A broadband router without a DHCP server function connected to this unit must be set up as described below. Before you set up the network, consult with your ISP or the network manager for the required settings.

It is advised that you also refer to the operation manual supplied with your network component.

• Any changes made to a router without the DHCP server function must be reflected to unit network settings.

1 Press

The Initial Setup screen is shown on the main display.

2 Select Network Setting  Configuration

3Use Setting, then press

Next steps are described separately between Wired Setting and Wireless Setting. Follow the instructions of the appropriate network type.

SET UP

Network

/

to select Wired Setting or Wireless

ENTER

Network Configuration

Wired Setting

Wireless Setting

English

Français Español

1 The “AM” and “PM” indicators appear only when the Time Format is set to the 12H mode. 2 Timer Setting need to be done before you turn on the timer. 3The sleep timer can be set by pressing SLEEP while the remaining time is displayed.

Changing the settings12

Static IP Address

192 . 168 . 2 . 4

SSID

[SOUND]

Change Text

Delete One Character

[CLEAR]

Wired Setting

1Use

/

to select DHCP

ENTER

The IP address setting screen is displayed.

2Use

///

or number buttons to adjust

the numbers, then press

• /: Moves the adjusting digit.

• /: Increases or decreases values.

Static IP Address

The IP address to be entered must be defined within the following ranges . If the IP address defined is beyond the following ranges, you cannot play back audio files stored on components on the network or listen to Internet radio stations.

Class A: 10.0.0.1 to 10.255.255.254 / Class B: 172.16.0.1 to 172.31.255.254 / Class C: 192.168.0.1 to

192.168.255.254

Subnet Mask

If an xDSL modem or a terminal adapter is directly connected to this unit, enter the subnet mask listed in your ISP documentation. In most of the cases, enter

255.255.255.0.

Gateway Address

If a gateway (router) is connected to this unit, enter the corresponding IP address.

Preferred DNS/Alternate DNS

If there is only one DNS server address listed in your ISP documentation, enter Preferred DNS. In case there are more t

han two DNS server addresses, enter Alternate

DNS in the other DNS server address field. Proxy Setup

Select Use Proxy Server when you connect this unit to the Internet via a proxy server. Enter the IP address of your proxy server in the Proxy Server Address field. Also, enter the port number of your proxy server in the ‘Proxy Port’ field.

Off

ENTER

, then press

Wireless Setting

1Use

/

to select Manual, then press

ENTER

Tip

• To select Auto, select the network name which you want to connect to and follow the instruction from the step 4.

Available Wireless Network AAAAA

BBBBB

CCCCC DDDDD

2Use

///

ENTER

• /: Moves the adjusting digit.

• /: Changes displayed character.

• SOUND: Switches character types.

• CLEAR: Deletes one character at a time.

to enter the SSID, then press

+ 102 hidden pages