Pioneer AVH-P4000DVD Installation Manual

Connecting the units

AVH-P4000DVD

INSTALLATION MANUAL

Printed in Thailand Imprimé en Thaïlande

<CRD4281-A/N> UC

MANUEL D’INSTALLATION

WARNING

• To avoid the risk of accident and the potential violation of applicable laws, the front DVD or TV (sold separately) feature should never be used while the vehicle is being driven. Also, Rear Displays should not be in a location where it is a visible distraction to the driver.

• In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit’s DVD features should not be used.

CAUTION

• PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.

• Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the vehicle battery. Engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point.

• It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving.

• Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism.

• Do not shorten any leads. If you do, the protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Note

• This unit cannot be installed in a vehicle without ACC (accessory) position on the ignition switch.

ACC position

• Use this unit in other than the following conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a battery.

— Cover any disconnected cable connectors with

insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly

to ground. — Never band together multiple speaker’s

negative cables.



No ACC position



• Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

• Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to connect connectors of the same color.

• Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.

Parts supplied

This product Power cord USB cable

Frame Flush surface screw

Touch panel pen

(5 × 6 mm) (8 pcs.)

Binding screw

(5 × 6 mm) (8 pcs.)

Connecting the units

Connecting the units Connecting the units

Connecting the units

Connecting the power cord

This product

Antenna input

Fuse (10 A)

Yellow Connect to the constant 12 V supply terminal.

Red Connect to terminal controlled by ignition switch (12 V DC).

Orange/white Connect to lighting switch terminal.

Black (chassis ground) Connect to a clean, paint-free metal location.

Front speaker Front speaker

Left Right

Rear speaker or Subwoofer (4 Ω)

When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything to Green and Green/black leads.









Not used.

White Gray

Gray/blackWhite/black

Green Violet

Green/black Violet/black

Green

Green/black

Violet

Violet/black













Fuse resistor

Rear speaker or Subwoofer (4 Ω)

Subwoofer (4 Ω) × 2

Yellow/black If you use equipment with Mute function, wire this lead to the Audio Mute lead on that piece of equipment. If not, keep the Audio Mute lead free of any connections.

Connection method

1. Clamp the lead.

Note:

· The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer.

Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

When you connect the separately sold multi-channel processor (e.g., DEQ-P8000) to this unit, do not connect anything to the speaker leads and system remote control (blue/white).

Note:

· Change the initial setting of this unit (refer to the

2. Clamp firmly with needle-nosed pliers.

Parking brake

Power supply side

Ground side

Operation Manual). The subwoofer output of this unit is monaural.

switch

When connecting to separately sold power amp

This product

Power amp (sold separately)

Front output

Rear output or subwoofer output

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal. (max. 300 mA 12 V DC).

When you connect the separately sold multi-channel processor (e.g., DEQ-P8000) to this unit, do not connect anything to the speaker leads and system remote control (blue/white).

When you connect the multi-channel processor to this unit, refer to multi-channel processor’s installation manual for the connection method.

Note:

· Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural.

Connect with RCA cables (sold separately)

System remote control

Left Right



Front speaker Front speaker

Rear speaker or Subwoofer









Perform these connections when using the optional amplifier.

Power amp (sold separately)

Rear speaker or Subwoofer

Connecting the system

USB cable Connect to sparately sold USB device.

1.5 m

(4 ft.11 in.)

Multi-CD player (sold separately)

Wired remote input H

ard-wired remote control adaptor can be connected (sold separately).

This product

20 cm (7-7/8 in.)

Gray

2 m (6 ft.7 in.)

Interface cable (e.g., CD-I200) (sold separately)

Dock connector

iPod with Dock connector

+ 4 hidden pages