Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by BB 0105 Service AudioPrinted in The NetherlandsSubject to modification
LASER PRODUCT
GB
3139 785 22660
3-43-4
SERVICE TEST PROGRAM
TUNER
TEST
TUNER
Button pressed?
Y
Display Tuner Version
"ccc"
TUNER
Button pressed?
Service frequencies are
copied to the RAM (see Table 1)
Tuner works normally except:
PROGRAM button
Disconnect
Mains cord ?
Y
Service Mode left
PRESET
10
11
Europe
"EUR"
1
87.5MHz
2
108MHz
3
531kHz
4
1602kHz
5
558kHz
6
1494kHz
7
153kHz
8
279kHz
9
198kHz
98MHz
87.5MHz
Note: * Depending on the selected grid frequency (9 or 10kHz)
By holding the TUNER and R buttons depressed while switching on the Mains supply, one
of the undermentioned features will be activated:
- the tuning grid frequency is toggled between 9kHz and 10kHz for the Oversea (/21) version.
- the extended FM1 (65.81MHz - 74MHz) is toggled on and off for East Eur. (/34) version.
N
N
N
East Eur.
"EAS"
87.5MHz
108MHz
531kHz
1602kHz
558kHz
1494kHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
East Eur. Extended-band
65.81MHz
108MHz
74MHz
87.5MHz
531kHz
1602kHz
558kHz
1494kHz
98MHz
70.01MHz
65.81MHz
Table 1
QUARTZ
TEST
Output at (Front Display Board)
pin 19 of uP = 2048Hz
Output at (Front Display Board)
pin 19 of uP = 2,929.6875Hz
"EAS"
O
Button pressed?
Y
Display shows
32K
O
Button pressed?
Y
Display shows
12M
9
Button pressed?
Y
USA
"USA"
87.5MHz
108MHz
530kHz
1700kHz
560kHz
1500kHz
98MHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
N
N
N
Oversea
"OSE"
87.5MHz
108MHz
531/530kHz*
1602/1700kHz*
558/560kHz*
1494/1500kHz*
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
To start service test program
hold
depressed while
plugging in the mains cord
Display shows the
ROM version
"S-Vyy"
(Main menu)
SERVICE
PLAY MODE
STANDBY-ON
Button pressed?
Y
Set is in Service PLAY Mode.
In case of failures, error
codes according to Table 2
will be displayed.
The Service Play Mode is intended to
detect and identify the failures in the CD Mode.
In this mode the electronics will still function
even when an error is detected so that
repair activities can be carried out.
Error code
E1000
E1001
E1002
E1003
E1005
E1006
E1007
E1008
E1020
E1070
E1071
E1079
Error Description
Focus Error
Triggered when the focus could not be found within a certain time when starting up the CD
or when the focus is lost for a certain time during play.
Radial Error
Triggered when the radial servo is off-track for a certain time during play.
Sledge In Error
The sledge did not reach its inner position (inner-switch is still close) before approximately
6 Sec. have passed by. Inner-switch or sledge motor problem.
Sledge Out Error
The sledge did not come out of its inner position (inner-switch is still open) before approximately
250 mSec. have passed by. Inner-switch or sledge motor problem.
Jump-offtrack error
Triggered in normal play when the jump destination could not be found within a certain time.
When this error occurred, software will try to recover by initiating the jump command again.
If it is recoverable, the disc will continue to play.
Subcode Error
Triggered when a new subcode was missing for a certain time during play.
PLL Error
The Phase Lock Loop could not lock within a certain time.
Turntable Motor Error
Generated when the CD could not reached 75% of speed during startup within a certain time.
Discmotor problem.
Focus Search Error
The focus point has not been found within a certain time.
The carousel switch is not open within certain time. This can happen when either the switch is
defective and closed all the time, or when the carousel is blocked when located exactly at a
disc position.
The carousel position switch did not close within a certain time. This can happen when the
switch is defective and never closes electrically, or when the carousel is blocked in between
two disc positions. The time-out is approximately 5 Sec.
The drawer could not enter the inside position is opening again. This can be caused because
the drawer is blocked by something and cannot go fully inside, or the drawer switch is defective
and does not close.
Æ™
& Aux
S refers to Service Mode
V refers to Version
yy refers to Software version number of the µProcessor
(counting up from 01 to 99)
DISPLAY
TEST
or
N
N
N
FW-C780
On
On
On
On
On
On
On
FW-P750
On
On
On
On
On
On
On
On
On
On
On
ACTION
"PASS" is displayed if the uProcessor read
back the test pattern correctly, otherwise
"ERROR" will be displayed.
Load default data. Display shows "NEW"
for 1 second.
Caution!
All presets from the customer will be lost!!
Display shows value for 2 seconds.
Values increases or decreases in steps of 1
until 0 (Min.) or 40 (Max.) is reached.
Mini 2001 FW-C5xx/7xx Service Test Program (dd wk0046)
Various
other Tests
N
Display shows Figure 1 and
switch all LEDs on (except ECO
POWER & VU Volume LEDs),
Figure 1
and switch alternate LEDs on
Figure 2
LEDs
FW-C500 , FW-C550
DISC 1
DISC 3
TAPE
TUNER
CENTRE
SURROUND LEFT
STEREO RIGHT
VAC
DBB
VU BACK LIGHT
VU VOLUME
TEST
EEPROM TESTA test pattern will be sent to the EEPROM.
2
Button pressed?
Y
and full VU deflection.
2
Button pressed?
Y
Display shows Figure 2
(see Table 3),
and partial VU deflection.
9
Button pressed?
Y
FW-C700 , FW-C720
On
On
On
On
On
On
On
On
Table 3
Activated with
R
9 to Exit
TEST
ROTARY
ENCODER TEST
QEEPROM FORMAT
Rotary
Volume Knob
Jog Shuttle Knob
Disconnect
mains cord
Table 2
LEAVE SERVICE
TESTPROGRAM
SET WIRING DIAGRAM
4-2
4-2
FRONT
VU Meter
( 1107 )
+5V6
VUmeter
GND_D
GND__D
1
HR 3p/100/3p OE
1840
1407
FFC AD 06p 140
1408
1
IR Receiver
FRONT
CDC KEYS
( 1107 )
GND_D
Cdc1Lit
Cdc3Lit
Key_Con
Cdc2Lit
Bit0
Bit1
1
1400
11
1409
1408
1
20
RC5
GND_B
+5V6_Con
GND-B
1800
1403
FFC AD 06p 180
Key2
TP_ADC1
+F
GND
TP_ADC2
TP_SH_CLK
1407
1406
FFC AD 07p 180
Key1
GND-B
CD Led
TP_SH_DATA
TP_SH_STR
7
1
TP_ADC2
( 1107 )( 1104 )
TAPE DD
ETF7
CD-CHANGER
3CDC-LC
1602
FFC AD 08p 120
1402
GND_D
Tuner Led
1
+F
GND
TP_ADC1
MPEG GND
ECHO I/P
FRONT
CONTROL/KEYS
1
1405
8
1
1412
Aux Led
Tape Led
FRONT
DISPLAY/u-P
( 1101 )
TP_SH_CLK
TP_SH_STR
TP_SH_DATA
( 1105 )
MPEG01B
CVBS
MIC_DET
1
( 1107 )
wOOx A
1
1403
1411
1706
SHR_DATA
DSA_DATA
DSA_ACK
GND_D_VCD
DSA_STR
GND_D
1603
wOOx B
1602
1404
1
VAC Led
GND_D
1405
TP_REC_LEFT
TP_REC_RIGHT
CD_SH_STR
CD_SH_DATA
GND_D_COAX
GND_D_CDTEXT
JOG A
GND_D
1600 (12p)
1603 (10p)
1601 (8p)
12
1404
FFC AD 10p 120 ( For C 5xx, 700 & 720 )
FFC AD 12p 120 (For C780 only )
FFC AD 12p 120 ( For P750 only )
Note : Some values may varies, see respective parts list for correct value.
This assembly drawing shows a summary of all possible versions.
For components used in a specific version see schematic diagram and respective parts list.
3139 113 3446 pt1 dd wk0047
5-3
FRONT CONTROL BOARD - CIRCUIT DIAGRAM
1600 F1
1601 H1
1602 D1
1603 H1
1650 D2
1651 C2
1652 C3
1653 C3
1654 C3
1655 C2
1656 D3
1657 D3
1658 D3
1659 D2
1660 D4
1661 D4
1662 C5
1663 C6
1664 C5
1665 C7
1666 C5
1667 C4
1668 C4
1669 C4
1670 C6
1671 D6
1672 D6
1673 D5
1674 D5
1675 D4
1690 A1
1691 A3
2600 G5
2603 G5
2604 B4
2605 B4
2606 B2
2607 B2
2608 C7
2613 D6
2615 A4
2620 F3
2622 F6
2623 F7
3600 G2
3604 A4
3605 A4
3606 A2
1234567
3612
270R
1652
CD
GND-B
3631
220R
1658
S_back
GND-B
6610
VacJOG_B
DSC
6611
6612
6613
TAPE
3632
270R
Woox_A
Woox_B
GND-B
STOP
+5V6
2620
3648
Gnd
3613
390R
1653
1657
GND-B
10u
10K
3649
10K
3654 120R
1691
EC12 1 3
Gnd
AUX
GND-B
3633
390R
NEXT
TapeCD
Aux
TunerAux
CD
220R3651
220R3652
270R3653
A
B
C
D
FE-ST-VK-N
E
F
G
H
JOG_A
JOG_B
1690
EC16
1602
1
2
3
4
5
6
7
8
WW00
1600
FE-ST-VK-N
1
2
3
4
5
6
7
8
9
10
11
12
1603
FE-ST-VK-N
12
MT14MT2
5
3
GndGnd
Key2
Key1
GND-B
Tuner
Gnd
Tape
Woox_A
Woox_B
1601
Vac
DSC
1
2
# 3600
3
4
+5V6
5
6
JOG_A
7
8
1
2
3
4
5
6
7
8
9
10
FE-ST-VK-N
9618
470R
Max_Woox_LedShClk
10K
10K
3607
3606
10n
10n
2607
2606
Gnd
3611
3610
220R
150R
1651
1655
PLAY
GND-B
3630
150R
1659
1650
S_fwd
GND-BGND-B
GND-B
Gnd
DBB_ShStr
IS_ShData
4600
9610
Gnd
DBB_Led
IS_Led
1234567
3607 A2
3608 G5
3609 G4
3610 C2
3611 C2
3612 C3
MT14MT2
1654
GND-B
+5V6
5
3614
560R
1656
3621
120R
3622
120R
Gnd
2
TUNER
GND-BGND-B
3634
560R
PREV
3623
120R
3624
120R
3650
7650
BC847B
3613 C3
3614 C4
3615 C4
3616 C5
3617 C5
3618 C6
3604
2604
Gnd
1669
WOOX_A
1675
GND-B
Tape
Aux
Tuner
CD
4K7
10K
Gnd
820R
3619 C6
3620 C6
3621 E4
3622 E4
3623 E4
3624 E4
+5V6
6602
1N4148
10K
10K
3605
2615
10n
10n
2605
Gnd
3615
820R
1668
Max/DPL
GND-B
GND-B
3636
3635
1K2
1661
RDS
NEWS
6603
6604
6605
6606
Gnd
DBB_ShStr
Max_Woox_LedShClk
3609
IS_ShData
Gnd
1667
3630 C2
3631 D3
3632 D3
3633 D3
3634 C4
3635 D4
47u
WOOX_B
1660
GND-B
5601
2u2
100p
Gnd
3636 D4
3637 D5
3638 D5
3639 D6
3640 D6
3643 G6
Note : Some values may varies, see respective parts list for correct value.
This assembly drawing shows a summary of all possible versions.
For components used in a specific version see schematic diagram and respective parts list.